Band-rejection filter based on a Bragg fiber with a defect layer

<正>A novel band-rejection filter based on a Bragg fiber with a defect layer is proposed.A defect layer is introduced in the periodic high/low index layers in the cladding of the Bragg fiber,which results in large confinement loss for some resonant wavelengths inside the band gap range of the Bragg fiber.A segment of the Bragg fiber with a defect layer can be used as a band-rejection filter,whose characteristics are mainly determined by the structure of the Bragg fiber.The simulation results show that the bandwidth of such a band-rejection filter is dependent on the number of the periodic high/low index layers in both sides of the defect layer in the cladding of the Bragg fiber.     

基于SM-NCF反射光谱辨识的液体折射率监测方法

针对分子生物学与环境监测领域高灵敏度特异性检测需求,提出一种基于反射光谱特征辨识的单端反射式光纤折射率传感器模型,并给出了这种基于多模干涉原理的单模光纤-无芯光纤(Single mode fiber-No core fiber, SM-NCF)串接结构传感机理及其理论模型。无芯光纤实质上是一种结构特殊的多模光纤,在实际应用中无芯光纤结构本身作为纤芯,外界环境介质当作包层,构成光波导结构。这与普通多模光纤相比,不需要采用氢氟酸对多模光纤的包层进行化学腐蚀,不会降低光纤的机械性能,也不会破坏芯模传输条件,可以更好的实现对周围环境折射率的传感监测。当无芯光纤所处外界环境折射率发生改变时,其波导结构和包层有效折射率均会发生改变,从而引起传输光信号的纵向传播常数和模场分布也会随之发生改变,最终导致不同波长对应传输光功率的变化。上述效应反映在反射光谱上,即干涉波谷对应的谐振波长、波谷峰值强度以及半波宽度发生相应变化,通过辨识该反射光谱特征就可实现对外界环境折射率的测量。借助光束传播法(BPM),数值模拟得到无芯光纤长度分别为自映像距离和非自映像距离时的SM-NCF内部光场能量分布规律,并制作了无芯光纤长度分别为自映像距离和非自映像距离的SM-NCF光纤折射率传感探头,将作为传感区域的无芯光纤一端与标准单模光纤熔接,采用磁控溅射技术在无芯光纤另一端面镀上金膜,用以提升反射光谱强度。在此基础上,搭建了基于SM-NCF终端反射型的光纤折射率试验系统,并开展了相关实验研究。研究结果表明,当无芯光纤长度是15 mm(自映像距离)时,随着液体折射率从1.331 5依次增大至1.390 2,SM-NCF反射光谱逐渐向长波方向偏移,其反射峰谐振波长对应的折射率灵敏度约为197.57 nm·RIU-1,相关系数为0.93;反射峰值强度也呈现逐渐降低趋势,其折射率灵敏度约为-62.80 dB·RIU-1。当无芯光纤长度是20 mm(非自映像距离)时,随着液体折射率依次增大,SM-NCF反射光谱呈现明显双峰现象,且均逐渐向长波方向偏移,dip2谐振峰波长折射率灵敏度约为133 nm·RIU-1,相关系数为0.96;反射峰值强度也呈现逐渐降低趋势,其折射率灵敏度约为-31.66 dB·RIU-1。对比分析可知,不论是从反射峰谐振波长偏移的角度,还是从反射峰值强度的角度,自映像距离长度对应的 SM-NCF终端反射型光纤传感器均具有较高灵敏度。对于相同折射率液体环境,非自映像距离长度对应的SM-NCF反射光谱半波宽度与自映像距离长度相比,呈现显著变窄趋势。相对于SMS透射型传感结构,当传感区域长度相同时,SM-NCF反射型结构能够实现对光波信号的往返两次调节。这种终端反射型SM-NCF传感器改进了传统透射型折射率传感器不便与待测液体相接触的缺点,具有结构简单、易于制作、抗电磁干扰能力强以及便于远程遥测等优点,能够为后续生化与环保监测领域研究应用提供有益支持。     

基于包层模的光纤布拉格光栅折射率传感特性

提出了基于光纤布拉格光栅(FBG)包层模式的折射率传感方案。实验中,利用不同浓度的丙三醇水溶液作为外界折射率传感溶液,采用氢氟酸溶液化学腐蚀的方法来减小光纤包层的直径以增大包层模式对外界折射率的敏感度,研究了腐蚀后光纤布拉格光栅包层模式的耦合波长对外部折射率的变化关系。实验结果表明在1.3300~1.4584的折射率范围内,包层模式耦合波长随外界折射率增大而增大,在接近光纤包层折射率处具有很高的折射率灵敏度,最大达到了172 nm/riu(refractive index unit)。而且,包层模谐振的光谱半峰全宽(约0.07 nm)仅为布拉格纤芯模谐振光谱半峰全宽的1/4,能够获得更好的传感精度。     

基于模式转换及双峰谐振效应的薄包层镀膜长周期光纤光栅特性研究

基于耦合模理论,首先研究了镀膜长周期光纤光栅(LPFG)高阶包层模的模式转换,划分了高阶包层模的非模式转换区及模式转换区。分析了高阶包层模有效折射率随薄膜厚度增加的响应特性,包层模谐振波长在模式转换区的偏移量要大于非模式转换区。在此基础上,研究了不同包层半径下高阶包层模谐振波长随光栅周期的变化情况,结果表明,相同包层半径下模式转换区内双峰间距的偏移量大于非模式转换区;无论在模式转换区还是非模式转换区,包层半径的减小将增加双峰间距的偏移量。最后分析了不同包层半径下的高阶包层模双峰透射谱在模式转换区及非模式转换区内的折射率响应,进而提出了薄包层镀膜LPFG的优化设计方案,当选定敏感膜层厚度及折射率处于镀膜LPFG的模式转换区内,光栅周期靠近相位匹配转折点时,将得到灵敏度高于传统LPFG双峰传感器的镀膜LPFG折射率型双峰传感器;而减小包层半径,将进一步提高传感器的分辨本领。     

基于包层模谐振的三包层石英特种光纤温度传感特性研究

提出了一种基于包层模谐振的光纤温度传感器. 它是通过将三包层石英特种光纤(TCQSF)两端分别与普通单模光纤(SMF)电弧熔接构成的SMF-TCQSF-SMF结构. 根据耦合模理论, 首先将TCQSF等效为三个同轴波导, 按各波导模场的分布特点标量计算其传输模式的色散曲线, 并深入研究其耦合长度与传输谱线之间的关系; 其次根据光纤的热光效应及热膨胀效应, 分析计算该传感器的温度灵敏度; 最后选取耦合长度为一个拍长时的传感器进行温度传感实验. 实验结果表明, 在35-95 ℃的温度变化范围内, 其温度灵敏度为73.74 pm/℃, 与理论计算结果一致. 因此, 该传感器具有结构简单、制备容易、灵敏度高、包层模激发可控等优点, 可用于工业生产、生物医学等温度传感领域.     

Theoretical analysis of novel fiber grating pair

A novel fiber grating pair that consists of a conventional long-period fiber grating and a fiber Bragg cladding grating (FBCG) is proposed. The FBCG is a new type of fiber grating in which refractive index modulation is formed in the cladding. Through the coupled-mode theory, we accurately calculate the coupling coefficients between modes supported in the fibers. And some other mode coupling features in the fiber cladding gratings are analyzed in detail. The calculation of the modes involved in this paper is based on a model of three-layer step-index fiber geometry. Then, we have investigated the sensitivity characteristics for variation of the modulation strengths of the fiber Bragg cladding gratings’ resonance peaks and the long-period cladding gratings’ (LPCGs) dual resonant peaks. Finally, the modulation strength sensitivity of the grating pair’s three resonant peaks is demonstrated, and the results indicate that these grating pairs may find potential applications in optical fiber sensing.     

基于花生形和光纤布喇格光栅结构的温度不敏感光纤曲率传感器

为了解决光纤传感器波长解调成本高以及交叉敏感的问题,提出一种温度不敏感光纤曲率传感器,该传感器是由花生形结构连接一个光纤布喇格光栅组成,对反射光采用强度解调.光进入花生形结构后激发出包层模式,通过光纤布喇格光栅反射后,反射的纤芯模再次在花生形结构产生不同阶次的包层模,然后和反射的纤芯模耦合,在反射光谱中除了光纤布喇格光栅的布喇格反射峰外,在短波长处出现若干个谐振峰,波长越小,包层模的阶次越高.实验结果表明曲率的变化范围为0.669 0~1.250 0m~(-1)时,测量到反射谐振峰平均光功率为2.260×10~(-7)~1.501×10~(-7) mW,灵敏度为-1.306×10~(-7) mW/m-1,在温度范围25℃~75℃内,反射包层模光功率基本保持不变.该传感器成本低且花生形结构制作简单、机械强度大.     

倾斜光纤光栅溶液折射率传感器的实验研究

根据倾斜光纤光栅(TFBG)和表面镀金的TFBG传感器测量折射率的基本原理,通过OptiGrating软件模拟了不同浓度溶液下TFBG的透射谱和芯层模与某阶包层模耦合引起的谐振峰,初步得出了TFBG各阶包层模随着外界折射率的增大而向右偏移、在一定的传感范围内中心波长与外界折射率呈线性关系的结论。用小型离子溅射仪对TFBG镀45 nm厚度左右的金膜,并用扫描电镜在微观上观察镀膜效果。通过不同浓度下的NaCl溶液、MgCl₂溶液、CaCl₂溶液实验,对比研究了裸TFBG和镀金TFBG传感器对溶液折射率的传感特性。从而验证了模拟仿真得出的结论并定量分析得知：镀金后具有表面等离子体共振的TFBG溶液折射率灵敏度大于500 nm·RIU-1,而裸TFBG为2 nm·RIU-1左右,大约提高了200～300倍,且在一定范围内中心波长与溶液折射率的线性拟合度都在0.99以上。     

全光纤干涉式结构中传感模式仿真分析

全光纤干涉式传感结构中包层模场与外界物理量作用,携带被感测信息,因此对包层模的研究是设计制作和提高该类传感器传感性能的关键.利用有限差分光束传播法获得传感光纤不同长度和不同芯径比时传感器对应的光谱,通过傅里叶变换获得其干涉频谱,计算出各主要参与干涉的包层模组的有效折射率,利用色散方程确定对应包层模.理论仿真结果显示,随着传感部分光纤长度增加,参与干涉的包层模式随之增加,并且向高阶模式变化,光谱变得稠密,是多阶包层模干涉的叠加,传感器输出干涉谱的自由光谱范围变小.随着输入光纤与传感光纤芯径比变化,会明显改变纤芯包层功率分布,同时,芯径比增大也会增加参与干涉的包层模种类和阶数.     

Widely tunable long-period fiber grating with nm-thick higher refractive index film overlay

By introducing a four-layer step-index waveguide modeling, the characteristics of long-period fiber grating (LPFG) with an nm-thick film overlay, which has higher refractive index than that of fiber cladding are investigated in detail. The influence of both the overlay thickness and refractive index on the tuning ability of LPFG is analyzed. The numerical results demonstrate that spectral response of LPFG is divided into three distinct regions as the overlay deposition increases and the shift of resonant wavelength is drastic in some special thickness range. In conjunction with higher-order cladding mode coupling and fiber cladding etching, the sensitivity of LPFG to the overlay refractive index is enhanced significantly and over 120 nm resonant wavelength tunable range is achieved.     

Numerical analysis of plasmon polarition refractive index fiber sensors with hollow core and a long period grating

The main principle of this design is based on the efficient energy transfer between the waveguide mode (WM) and the co-directional SPP provided by a properly designed fiber long period grating (LPG). This LPG is imprinted into a waveguide fiber layer of a specially designed hollow core optical fiber. The simulations are based on the finite element method (FEM) algorithm in electromagnetics and coupled mode theory for gratings. Compared to the previous proposed structure using a fiber Bragg grating (FBG), this novel kind of sensor can greatly enhance the refractive index sensitivity, e.g., from 5.93 nm/RIU (with FBG) to 817 nm/RIU (with LPG) at the sensing refractive index of 1.40. The other advantage is that the working conditions can be performed for the well-developed telecom wavelength windows 1500-1600 nm.     

Fiber Optical Bragg Grating Refractometer

We have demonstrated an evanescent field refractive indexfiber sensor comprising a 42-mm Bragg grating in an etched fiber together with a tunable Distributed Bragg Reflector (DBR) laser. Characterization of different aqueous sucrose solutions resulted in a resolution of roughly 10 mM sucrose. The sensor in the presented form has a theoretical sensitivity of higher than 10 5 refractive index unit (riu) in a refractive index region close to the cladding index of the fiber. However, the technique allows for an even higher sensitivity than 10 6 riu with a proper signal processing scheme.     

Simultaneous Measurement of Temperature and Refractive Index of Liquid Using Cladding-Etched Double-Core Fiber Bragg Grating

Abstract

This study proposed and demonstrated a fiber Bragg grating sensor for simultaneous detection of the temperature and refractive index of a liquid. The fiber Bragg grating is composed of three index layers: an inner core, an outer core, and a cladding. The cladding was etched for evanescent wave coupling between the outer core mode and an external liquid. The Bragg wavelength of the inner core mode is used for obtaining temperature data, while the refractive index for the liquid was determined by using the difference between the Bragg wavelength of the inner core mode and that of outer core mode.     

高灵敏度光纤应变传感器

提出一种基于锥形光纤和光纤F-P腔组合结构的光纤应变传感器。该传感器包含单模光纤拉锥形成的锥区和石英毛细管构建的F-P腔2个应变敏感区域。理论分析了光波在该传感器中的传播过程,获得了该传感器的光强传输函数。由于锥形光纤中激发出的包层高阶模参与干涉,导致传感器干涉光谱具有调制特性。实验获得了该传感器的干涉光谱,通过分析谐振波长偏移或消光比变化对应变实现独立测量,在0~500 με的测量范围内,该传感器的应变灵敏度为14.6 pm/με。利用锥形光纤引发的模式干涉和F-P腔的双光束干涉效应共同作用形成受调制的干涉谱型进行应变传感,应变灵敏度高,同时具备2种独立的应变检测手段(谐振波长和消光比检测)。     

不同包层直径的倾斜光纤光栅折射率传感特性

倾斜光纤光栅的透射谱中有纤芯模和大量的包层模,它们具有与布拉格光栅相同的温度特性.利用HF酸腐蚀的方法得到具有不同包层直径的倾斜光纤光栅,研究了其对外界折射率的传感特性.结果表明,外界环境折射率在1.333～1.4532之间变化时,同一直径倾斜光纤光栅的高阶包层模的敏感性要比低阶包层模强;随着包层直径的减小,包层模的敏感性增强,且在折射率比较高的环境中有更高的敏感性.因此,利用倾斜光纤光栅的温度特性不仅可以解决温度交叉敏感问题,而且通过小同的腐蚀程度能定制所需要的灵敏度,以实现对环境折射率的高灵敏度测量.该办法可应用于对生物和化学等高灵敏度传感领域的各种溶液进行实时监控.     

基于薄包层极大倾角光纤光栅的灵敏度增强型振动传感器

提出了一种薄包层极大倾角光纤光栅悬臂梁振动传感器,采用基于标准单模光纤的极大倾角光纤光栅,从理论上分析包层半径的减小对波导色散因子、包层模的有效折射率、轴向应变灵敏度因子、轴向应变灵敏度及模式阶数的影响,并进行数值仿真,为其振动传感增敏方法提供理论依据.然后使用氢氟酸腐蚀光纤包层,构成不同直径的极大倾角光纤光栅并进行相...     

镀高折射率纳米膜的长周期光纤光栅特性研究

针对镀高折射率纳米膜的长周期光栅,建立了传感理论模型,研究了长周期光栅的谐振波长与纳米膜厚度及外界折射率的关系,给出不同纳米膜厚度下长周期光栅不同包层模式重组特性.研究发现,当长周期光栅外面镀上一层沿角向均匀分布的纳米膜时,随着膜厚变化会出现包层模分布的明显调制;适当选择镀膜参数和外界介质折射率,最低次包层模式HE1,2会成为镀膜层中的导模,其他的包层模式将会发生模式转换现象;对于较低次包层模式(如HE1.6),在模式转换的时候存在两步转换,而高次的包层模只有一步转换(如HE1.14).同时给出了包层模式转换对外界折射率响应的关系:当膜层厚度增加时,长周期光栅模式转换现象移至低折射率区域.     

Effect of the Pd-Au thin film thickness uniformity on the performance of an optical fiber hydrogen sensor

Thin alloy film of Pd and Au, formed by simultaneous electron-beam and thermal evaporation techniques, respectively, is used in the design of an optical fiber hydrogen sensor. The sensor consists of a multimode fiber (MMF) in which a short section of single mode fiber (SMF), coated with the Pd-Au thin film, is inserted. Due to core diameter mismatch, the SMF cladding guides light, allowing the interaction between the sensing layer and the guided light. When the sensor is exposed to hydrogen, the Pd-Au layer refractive index diminishes and causes attenuation changes on the transmitted light. Several samples with different layer thickness uniformity were fabricated and tested in a very simple experimental set-up. We have observed that the sensor signal change is dependant on layer thickness uniformity, since the effective interaction length between the evanescent field and the sensing layer is increased. By contrast, such uniformity practically has no influence on the time response of the sensor. The resulting Pd-Au film can detect 4% hydrogen with a response time of 15 s.     

Absorption Measurement Using a Leaky Waveguide Mode

We propose an optical waveguide sensor using a leaky mode for absorption measurement of liquid samples. This sensor uses a single coupling prism. A cladding layer and a waveguide layer are directly deposited on the reflecting surface of the prism. The intensity of the internally reflected beam at an appropriate incident angle is very sensitive to the imaginary part of the sample attached to the surface of the waveguide layer. The sensitivity of this sensor is controlled by the thicknesses of both cladding and waveguide layers. We studied the performance of the sensor by numerical calculation.     

基于长周期光纤光栅的磁场传感方案的实现

长周期光纤光栅是近几年出现的一种新型光纤器件。其耦合机理是前向传输的纤芯基模与前向传输的各阶包层模式之间的耦合 ,这与光纤布喇格光栅明显不同。它对温度、应力、弯曲及外部折射率的变化具有相当高的灵敏度 ,是一种理想的光纤型敏感结构。提出利用长周期光纤光栅谐振波长的移动或移动变化量进行磁场强度的测量 ,并进行了理论推导、仿真实验及分析研究。得出了谐振波长变化量与外界磁场强度的关系模型。分析了设计中应该考虑的因素。