Fabrication and characterization of Meldola's blue/zinc oxide hybrid electrodes for efficient detection of the reduced form of nicotinamide adenine dinucleotide at low potential

We report the synthesis and the electrochemical properties of hybrid films made of zinc oxide (ZnO) and Meldola's blue dye (MB) using cyclic voltammetry (CV). MB/ZnO hybrid films were electrochemically deposited onto glassy carbon, gold and indium tin oxide-coated glass (ITO) electrodes at room temperature (25 ± 2 °C) from the bath solution containing 0.1 M Zn(NO₃)₂, 0.1 M KNO₃ and 1 × 10⁻⁴ M MB. The surface morphology and deposition kinetics of MB/ZnO hybrid films were studied by means of scanning electron microscopy (SEM), atomic force microscopy (AFM) and electrochemical quartz crystal microbalance (EQCM) techniques, respectively. SEM and AFM images of MB/ZnO hybrid films have revealed that the surfaces are well crystallized, porous and micro structured. MB molecules were immobilized and strongly fixed in a transparent inorganic matrix. MB/ZnO hybrid films modified glassy carbon electrode (MB/ZnO/GC) showed one reversible redox couple centered at formal potential (E⁰′) −0.12 V (pH 6.9). The surface coverage (Γ) of the MB immobilized on ZnO/GC was about 9.86 × 10⁻¹² mol cm⁻² and the electron transfer rate constant (ks) was determined to be 38.9 s⁻¹. The MB/ZnO/GC electrode acted as a sensor and displayed an excellent specific electrocatalytic response to the oxidation of nicotinamide adenine dinucleotide (NADH). The linear response range between 50 and 300 μM NADH concentration at pH 6.9 was observed with a detection limit of 10 μM (S/N = 3). The electrode was stable during the time it was used for the full study (about 1 month) without a notable decrease in current. Indeed, dopamine (DA), ascorbic acid (AA), acetaminophen (AP) and uric acid (UA) did not show any interference during the detection of NADH at this modified electrode.     

Evaluation of DGT techniques for measuring inorganic uranium species in natural waters: Interferences,deployment time and speciation

Three adsorbents (Chelex-100, manganese dioxide [MnO₂] and Metsorb), used as binding layers with the diffusive gradient in thin film (DGT) technique, were evaluated for the measurement of inorganic uranium species in synthetic and natural waters. Uranium (U) was found to be quantitatively accumulated in solution (10–100 μg L⁻¹) by all three adsorbents (uptake efficiencies of 80–99%) with elution efficiencies of 80% (Chelex-100), 84% (MnO₂) and 83% (Metsorb). Consistent uptake occurred over pH (5–9), with only MnO₂ affected by pH < 5, and ionic strength (0.001–1 mol L⁻¹ NaNO₃) ranges typical of natural waters, including seawater. DGT validation experiments (5 days) gave linear mass uptake over time (R² ≥ 0.97) for all three adsorbents in low ionic strength solution (0.01 M NaNO₃). Validation experiments in artificial sea water gave linear mass uptake for Metsorb (R² ≥ 0.9954) up to 12 h and MnO₂ (R² ≥ 0.9259) up to 24 h. Chelex-100 demonstrated no linear mass uptake in artificial sea water after 8 h. Possible interferences were investigated with SO₄²⁻ (0.02–200 mg L⁻¹) having little affect on any of the three DGT binding layers. PO₄³⁻ additions (5 μg L⁻¹–5 mg L⁻¹) interfered by forming anionic uranyl phosphate complexes that Chelex-100 was unable to accumulate, or by directly competing with the uranyl species for binding sites, as with MnO₂ and the Metsorb. HCO₃⁻ (0.1–500 mg L⁻¹) additions formed anionic species which interfered with the performance of the Chelex-100 and the MnO₂, and the Ca²⁺ (0.1–500 mg L⁻¹) had the affect of forming labile calcium uranyl species which aided uptake of U by all three resins. DGT field deployments in sea water (Southampton Water, UK) gave a linear mass uptake of U over time with Metsorb and MnO₂ (4 days). Field deployments in fresh water (River Lambourn, UK) gave linear uptake for up to 7 and 4 days for Metsorb and MnO₂ respectively. Field deployment of the Metsorb-DGT samplers with various diffusive layer thicknesses (0.015–0.175 cm) allowed accurate measurements of the diffusive boundary layer (DBL) and allowed DBL corrected concentrations to be determined. This DBL-corrected U concentration was half that determined when the effect of the DBL was not considered. The ability of the DGT devices to measure U isotopic ratios with no isotopic fractionation was shown by all three resins, thereby proving the usefulness of the technique for environmental monitoring purposes.     

A highly sensitive hydrogen peroxide amperometric sensor based on MnO2-modified vertically aligned multiwalled carbon nanotubes

In this report, a highly sensitive amperometric sensor based on MnO₂-modified vertically aligned multiwalled carbon nanotubes (MnO₂/VACNTs) for determination of hydrogen peroxide (H₂O₂) was fabricated by electrodeposition. The morphology of the nanocomposite was characterized by scanning electron microscopy, energy-dispersive X-ray spectrometer and X-ray diffraction. Cyclic voltammetry, chronoamperometry and electrochemical impedance spectroscopy were applied to investigate the electrochemical properties of the MnO₂/VACNTs nanocomposite electrode. The mechanism for the electrochemical reaction of H₂O₂ at the MnO₂/VACNTs nanocomposite electrode was also discussed. In borate buffer (pH 7.8, 0.20 M), the MnO₂/VACNTs nanocomposite electrode exhibits a linear dependence (R = 0.998) on the concentration of H₂O₂ from 1.2 × 10⁻⁶ M to 1.8 × 10⁻³ M, a high sensitivity of 1.08 × 10⁶ μA M⁻¹ cm⁻² and a detection limit of 8.0 × 10⁻⁷ M (signal/noise = 3). Meanwhile, the MnO₂/VACNTs nanocomposite electrode is also highly resistant towards typical inorganic salts and some biomolecules such as acetic acid, citric acid, uric acid and d-(+)-glucose, etc. In addition, the sensor based on the MnO₂/VACNTs nanocomposite electrode was applied for the determination of trace of H₂O₂ in milk with high accuracy, demonstrating its potential for practical application.     

Synthesis and high electrochemical performance of polyaniline/MnO2-coated multi-walled carbon nanotube-based hybrid electrodes

Multi-layered electrodes which consist of polyaniline (PANI)/manganese dioxide (MnO₂)-multi-walled carbon nanotubes (MWNTs) are prepared as the electrode materials for supercapacitors. MnO₂-MWNTs are made by the in situ direct coating method to deposit MnO₂ onto MWNTs; the core/shell structure of multi-layered fibrous electrodes can also be obtained by PANI coating onto the MnO₂-MWNTs. The effect of PANI coating on the electrochemical performance and cyclic stability of MnO₂-MWNTs is investigated. From the cyclic voltammograms, the PANI/MnO₂-MWNTs show remarkably enhanced specific capacitance and cycle stability compared to MnO₂-MWNTs, where the highest specific capacitance (350 F/g) is obtained at a current density of 0.2 A/g for the PANI/MnO₂-MWNTs as compared to 92 F/g for pristine MWNTs and 306 F/g for MnO₂-MWNTs. This indicates that the improved electrochemical performance of PANI/MnO₂-MWNTs is due to the enhanced electrical properties by nano-scale-coated MnO₂ onto MWNTs and the PANI coating that leads to the increased cycle stability by delaying the dissolution of MnO₂ during charge/discharge tests.     

Doping of polyaniline films with organic sulfonic acids in aqueous media and the effect of water on these doped films

Polyaniline (PANI) films in the form of emeraldine salt (ES) doped with aqueous organic sulfonic acids such as camphorsulfonic acid (CSA), p-toluenesulfonic acid (p-TSA) and dodecylbenzenesulfonic acid (DBSA) were studied. The ES films were obtained by treating the PANI in the form of emeraldine base (EB) with the aqueous solution of the acids. The dopant weight fraction (w), which is related to the mass gain during the redoping of EB, was in situ determined using a quartz crystal microbalance (QCM). The behaviour of PANI doping with different acids indicates that the uptake shows a slow diffusion process. The kinetics of the doping reaction is dominated by Fickian diffusion kinetics. The diffusion coefficients (D) of the dopant ions into the PANI chains were determined and were found to vary within the range of (1.6-18) × 10⁻¹⁵ cm² s⁻¹. Moreover, the effect of water on these doped ES films was studied. The starting point is the fact that PANI-coated the electrode of QCM shows significant frequency shifts on exposure to water. The changes in the frequency as a function of treatment time in water were quantitatively measured. The response of the device suggests that the mass decrease under water exposure is due to dopant ions release. The latter films were dedoped by exposure to ammonia solution to obtain the EB film form. A further decrease in the mass of the films was observed. The percentage of the mass loss due to water exposure is found to be less than w determined during the dedoping process.     

Layer-by-layer self-assembly of polyelectrolyte complexes and their multilayer films for pervaporation dehydration of isopropanol

Two negatively charged polyelectrolyte complex colloidal nanoparticles (PEC⁻) and one positively charged nanoparticle (PEC⁺) were prepared and used as novel layer-by-layer (LbL) building blocks. These PEC nanoparticles include poly(2-methacryloyloxy ethyl trimethylammonium chloride)/sodium carboxymethyl cellulose (PDMC/CMCNa PEC⁻), poly(diallyldimethylammonium chloride)/CMCNa (PDDA/CMCNa PEC⁻) and PDDA/poly(sodium-p-styrenesulfonate) (PDDA/PSS PEC⁺). LbL multilayer films based on (PEC⁺/PEC⁻) were constructed on both quartz slides and modified polyamide (MPA) reverse osmosis support membranes. UV–vis spectroscopy, quartz crystal microbalance (QCM), field emission scanning microscopy (FESEM) and atomic force microscopy (AFM) were utilized to follow the thickness growth and morphology evolution of these multilayer films with increasing bi-layer numbers. LbL multilayer films deposited on MPA support membranes were subjected to pervaporation dehydration of 10 wt% water–isopropanol and effect of bi-layer numbers and feed temperature on pervaporation performance was studied. Generally, PEC⁺/PEC⁻ can be LbL self-assembled successfully on both substrates with a thickness growth rate ca. 200 nm/bi-layer. Moreover, PEC⁺/PEC⁻ multilayer films show high pervaporation performance with film thickness up to several micrometers. For example, performance of the multilayer films in dehydrating 10 wt% water–isopropanol at 50 °C is J = 1.18 kg/m² h, α = 1013 for (PEC⁺/PDMC-CMCNa PEC⁻)₂₄ and J = 1.36 kg/m² h, α = 938 for (PEC⁺/PDMC-CMCNa PEC⁻)₂₅, respectively.     

Photoluminescence and Raman spectroscopy studies on polyaniline/PbI2 composite

Functionalization of PbI₂ with conjugated polymers (polyaniline-emeraldine base (PANI-EB) or polyaniline-emeraldine salt (PANI-ES)) is demonstrated by Raman and luminescence studies. PbI₂/PANI hybrid material was prepared by electrochemical polymerization of aniline onto the PbI₂ modified Pt electrode and mechanico-chemical reaction between the two constituents. PANI interacting with the PbI₂ gives rise to new Raman bands at 80, 144 and 170 cm⁻¹. First line reveals the formation of “stacking faults” that disrupt the I-Pb-I layers stacking along the c axis by the insertion of polymer molecules. The bands at 144 and 170 cm⁻¹ are attributed to the vibrational mode associated with Pb-NHR″₂ (R″=C₆H₄) bond. The functionalization of PbI₂ with PANI-EB brings forth the PANI-ES form. Depending on the semiconducting (PANI-EB) or conducting (PANI-ES) properties of the polymer in the PbI₂/PANI intercalated material, a partial or total collection of the charges generated under band to band irradiation is revealed by photoluminescence studies.     

Direct electrochemistry with enhanced electrocatalytic activity of hemoglobin in hybrid modified electrodes composed of graphene and multi-walled carbon nanotubes

A graphene (GR) and multi-walled carbon nanotubes (MWCNT) hybrid was prepared and modified on a 1-hexylpyridinium hexafluorophosphate based carbon ionic liquid electrode (CILE). Hemoglobin (Hb) was immobilized on GR-MWCNT/CILE surface with Nafion as the film forming material and the modified electrode was denoted as Nafion/Hb-GR-MWCNT/CILE. Spectroscopic results revealed that Hb molecules retained its native structure in the GR-MWCNT hybird. Electrochemical behaviors of Hb were carefully investigated by cyclic voltammetry with a pair of well-defined redox peaks obtained, which indicated that direct electron transfer of Hb was realized in the hybrid modified electrode. The result could be attributed to the synergistic effects of GR-MWCNT hybrid with enlarged surface area and improved conductivity through the formation of a three-dimensional network. Electrochemical parameters of the immobilized Hb on the electrode surface were further calculated with the results of the electron transfer number (n) as 1.03, the charge transfer coefficient (a) as 0.58 and the electron-transfer rate constant (k_s) as 0.97 s⁻¹. The Hb modified electrode showed good electrocatalytic ability toward the reduction of different substrates such as trichloroacetic acid in the concentration range from 0.05 to 38.0 mmol L⁻¹ with a detection limit of 0.0153 mmol L⁻¹ (3σ), H₂O₂ in the concentration range from 0.1 to 516.0 mmol L⁻¹ with a detection limit of 34.9 nmol/L (3σ) and NaNO₂ in the concentration range from 0.5 to 650.0 mmol L⁻¹ with a detection limit of 0.282 μmol L⁻¹ (3σ). So the proposed electrode had the potential application in the third-generation electrochemical biosensors without mediator.     

Defluoridation kinetics of 200 °C calcined bauxite, gypsum, and magnesite and breakthrough characteristics of their composite filter

Reaction kinetics and breakthrough characteristics in water defluoridation were studied through experiments with 200 °C-calcined bauxite, gypsum and magnesite and their composite filter. The aim was to determine defluoridation potential of a composite filter of the three locally sourced natural materials in contribution towards fluorosis mitigation. The materials were crushed and sieved to particle sizes of 1.2-1.4 mm diameter, and then heat-treated at 200 °C for 2 h. Their defluoridation capacities and reaction kinetics were determined in batch. A composite was then prepared in the ratio of the loading capacities. Breakthrough characteristics were experimented on in fixed bed through bed depth service time (BDST) design model, empty bed residence time (EBRT) optimisation model and the two parameter-logistics (2-PL) model. Mean loading capacities of 5.6, 3.4 and 1.7 mg F⁻/g were obtained for bauxite, gypsum and magnesite, respectively. Loading capacities decreased, while sorption percentages increased, with increase in dose level. Second order kinetics observed had rate constants 4.07 × 10⁻², 1.87 × 10⁻², 1.59 × 10⁻² g mg⁻¹ min⁻¹ for bauxite, gypsum and magnesite, respectively. Composites, bauxite and gypsum decreased, while magnesite increased water pH. Time at 50% breakthrough (τ) obtained experimentally compared well with τ obtained through the two-parameter logistics model indicating good fitness of data to the model. Greater doses obtained higher breakthrough times that were, 120, 210, 255 and 360 min for 45, 75, 120 and 150 g, respectively. Critical bed depth (Z_o), 7.71 cm and an operating line, ? = 4 × 10⁻⁴δ − 0.0757δ + 4.86 (? = adsorbent exhaustion rate, δ = EBRT) were obtained. The water quality was within recommended quality limits for pH, apparent colour, hardness, and residual concentrations of SO₄²⁻, Cl⁻, Fe²⁺, and Al³⁺ in fixed bed. The research showed that a composite filter of the three materials, prepared in the ratio of their loading capacities and calcined at 200 °C, is a potential defluoridating filter in fixed bed configuration.     

Production and characterization of a broad-specificity polyclonal antibody for O,O-diethyl organophosphorus pesticides and a quantitative structure-activity relationship study of antibody recognition

Polyclonal antibody (PAb) with broad-specificity for O,O-diethyl organophosphorus pesticides (OPs) against a generic hapten, 4-(diethoxyphosphorothioyloxy)benzoic acid, was produced. The obtained PAb showed high sensitivity to seven commonly used O,O-diethyl OPs in a competitive indirect enzyme-linked immunosorbent assay (ciELISA) using a heterologous coating antigen, 4-(3-(diethoxyphosphorothioyloxy)phenylamino)-4-oxobutanoic acid. The 50% inhibition value (IC₅₀) was 348 ng mL⁻¹ for parathion, 13 ng mL⁻¹ for coumaphos, 22 ng mL⁻¹ for quinalphos, 35 ng mL⁻¹ for triazophos, 751 ng mL⁻¹ for phorate, 850 ng mL⁻¹ for dichlofenthion, and 1301 ng mL⁻¹ for phoxim. The limit of detection (LOD) met the ideal detection criteria of all the seven OP residues. A quantitative structure-activity relationship (QSAR) model was constructed to study the mechanism of antibody recognition using multiple linear regression analysis. The results indicated that the frontier-orbital energies (energy of the highest occupied molecular orbital, E_HOMO, and energy of the lowest unoccupied molecular orbital, E_LUMO) and hydrophobicity (log of the octanol/water partition coefficient, log P) were mainly responsible for the antibody recognition. The linear equation was log(IC₅₀) = −63.274E_HOMO + 15.985E_LUMO + 0.556 log P − 25.015, with a determination coefficient (r²) of 0.908.     

Facile fabrication of mesoporous manganese oxides as advanced electrode materials for supercapacitors

Mesoporous manganese oxides (MnO₂) were synthesized via a facile chemical deposition strategy. Three kinds of basic precipitants including sodium carbonate (Na₂CO₃), sodium bicarbonate (NaHCO₃), and sodium hydroxide (NaOH) were employed to adjust the microstructures and surface morphologies of MnO₂ materials. The obtained MnO₂ materials display different microstructures. Great differences are observed in their specific surface area and porosity properties. The microstructures and surface morphologies characteristics of MnO₂ materials largely determine their pseudocapacitive behavior for supercapacitors. The MnO₂ prepared with Na₂CO₃ precipitant exhibits the optimal microstructures and surface morphologies compared with the other two samples, contributing to their best electrochemical performances for supercapacitors when conducted either in the single electrode tests or in the capacitor measurements. The optimal MnO₂ electrode exhibits a high specific capacitance (173 F g^–1 at 0.25 A g^?1), high-rate capability (123 F g^?1 at 4 A g^?1), and excellent cyclic stability (no capacitance loss after 5,000 cycles at 1 A g^?1). The optimal activated carbon//MnO₂ hybrid capacitor exhibits a wide working voltage (1.8 V), high-power and high-energy densities (1,734 W kg^?1 and 20.9 Wh kg^?1), and excellent cycling behavior (93.8 % capacitance retention after 10,000 cycles at 1 A g^?1), indicating the promising applications of the easily fabricated mesoporous MnO₂ for supercapacitors.     

Investigations on electrochemical supercapacitors using polypyrrole redox electrodes and PMMA based gel electrolytes

Polypyrrole based solid state electrochemical redox supercapacitors have been fabricated using the polymeric gel electrolytes comprising of poly methyl methacrylate (PMMA)-propylene carbonate (PC)-ethylene carbonate (EC)-perchlorate salts of different cations [Li⁺, Na⁺ and (C₂H₅)₄N⁺ (TEA⁺)]. A comparative study has been carried out using linear sweep reversal voltammetry, complex impedance spectroscopy and constant current charge-discharge tests. The capacitance values of the cells have been observed to be in the range of 15.3-22.5 mF cm⁻² (equivalent to single electrode specific capacitance of 120-178 F g⁻¹ of polypyrrole). This corresponds to the values of energy density 16.7-24.7 Wh kg⁻¹ and power density 1.6-2.8 kW kg⁻¹ calculated for the working voltage of 1.0 V limited for polypyrrole based redox capacitors. Substantial improvements in the coulombic efficiency of the cells have been observed (close to 100%) due to the application of gel electrolytes showing flexible and liquid like behaviour. Further, the types and sizes of the cations in the gel electrolytes do not play any dominant role in the capacitive behaviour of the redox cells.     

Pre-evaluation of metal ions as a catalyst on chemiluminometric sequential injection analysis with luminol-H2O2 system

Catalytic effect of metal ions on luminol chemiluminescence (CL) was investigated by sequential injection analysis (SIA). The SIA system was set up with two solenoid micropumps, an eight-port selection valve, and a photosensor module with a fountain-type chemiluminescence cell. The SIA system was controlled and the CL signals were collected by a LabVIEW program. Aqueous solutions of luminol, H₂O₂, and a sample solution containing metal ion were sequentially aspirated to the holding coil, and the zones were immediately propelled to the detection cell. After optimizing the parameters using 1 × 10⁻⁵ M Fe³⁺ solution, catalytic effect of some metal species was compared. Among 16 metal species examined, relatively strong CL responses were obtained with Fe³⁺, Fe²⁺, VO²⁺, VO₃⁻, MnO₄⁻, Co²⁺, and Cu²⁺. The limits of detection by the present SIA system were comparable to FIA systems. Permanganate ion showed the highest CL sensitivity among the metal species examined; the calibration graph for MnO₄⁻ was linear at the concentration level of 10⁻⁸ M and the limit of detection for MnO₄⁻ was 4.0 × 10⁻¹⁰ M (S/N = 3).     

Mechanism study on inorganic oxidants induced inhibition of Ru(bpy)₃²+ electrochemiluminescence and its application for sensitive determination of some inorganic oxidants

Inhibited Ru(bpy)₃²⁺ electrochemiluminescence by inorganic oxidants is investigated. Results showed that a number of inorganic oxidants can quench the ECL of Ru(bpy)₃²⁺/tri-n-propylamine (TPrA) system, and the logarithm of the decrease in ECL intensity (ΔI) was proportional to the logarithm of analyte concentrations. Based on which, a sensitive approach for detection of these inorganic oxidants was established, e.g. the log-log plots of ΔI versus the concentration of MnO₄⁻, Cr₂O₇²⁻ and Fe(CN)₆³⁻ are linear in the range of 1 × 10⁻⁷ to 3 × 10⁻⁴ M for MnO₄⁻ and Cr₂O₇²⁻, and 1 × 10⁻⁷ to 1 × 10⁻⁴ M for Fe(CN)₆³⁻, with the limit of detection (LOD) of 8.0 × 10⁻⁸ M, 2 × 10⁻⁸ M, and 1 × 10⁻⁸ M, respectively. A series of experiments such as a comparison of the inhibitory effect of different compounds on Ru(bpy)₃²⁺/TPrA ECL, ECL emission spectra, UV-Vis absorption spectra etc. were investigated in order to discover how these inorganic analytes quench the ECL of Ru(bpy)₃²⁺/TPrA system. A mechanism based on consumption of TPrA intermediate (TPrA^·) by inorganic oxidants was proposed.     

Theoretical study of intra- and inter-chain magnetic interactions in [Ni(chxn)2Br]Br2

The intra- and the inter-chain magnetic interactions in [Ni(chxn)₂Br]Br₂, which is one of the typical one-dimensional (1-D) MX complexes are examined by using an unrestricted hybrid DFT (UB3LYP) method. Calculated effective exchange integral (J) value along the 1-D chain is 2J_Intra = −4016 K and is close to an experimental result (−3600 K). On the other hand, a very weak anti-ferromagnetic inter-chain interaction through Br⁻ ions is observed. The value is estimated to be 2J_Inter = −2 to −6 K. In addition to the J values, transfer integral (t), on-site Coulomb repulsion (U) and charge transfer energy (E^CT) values along the 1-D chain are also estimated to be 0.46, 2.46 and 0.6 eV, respectively.     

Influence of carbon shell structure on electrochemical performance of multi-walled carbon nanotube electrodes

Core/shell nanostructures have received considerable attention due to the synergistic effect of their combination of materials. In this work, core/shell carbon/multi walled carbon nanotubes (MWNTs) (C-MWNTs) composed of core MWNTs and carbon shells were prepared to obtain a new type of carbon electrode materials. Carbon shells containing nitrogen groups were prepared by coating polyaniline (PANI) onto the MWNTs by in situ polymerization and subsequent carbonization at 850 °C. After carbonization, the C-MWNTs contained 5.84% nitrogen and showed a hollow structure and crystallinity like that of pristine MWNTs. In addition, the C-MWNTs exhibited electrochemical performance superior to that of pristine MWNTs, and the highest specific capacitance (231 F g⁻¹) of the C-MWNTs was obtained at a scan rate of 0.1 A g⁻¹, as compared to 152 F g⁻¹ for pristine MWNTs. This superior performance is attributed to the maintenance of high electrical conductivity by the π–π interaction between the carbon layer and the MWNTs, increased specific surface area of C-MWNTs, and the presence of nitrogen groups formed on the carbon electrode after the carbonization of the shell PANI.     

Electrochemistry and scanning electron microscopy of polyaniline/peroxidase-based biosensor

An amperometric biosensor was prepared by in situ deposition of horseradish peroxidase (HRP) enzyme on a polyaniline (PANI)-doped platinum disk electrode. The PANI film was electrochemically deposited on the electrode at 100 mV s⁻¹/Ag-AgCl. Cyclic voltammetric characterization of the PANI film in 1 M HCl showed two distinct redox peaks, which prove that the PANI film was electroactive and exhibited fast reversible electrochemistry. The surface concentration and film thickness of the adsorbed electroactive species was estimated to be 1.85×10⁻⁷ mol cm⁻² and approximately 16 nm, respectively. HRP was electrostatically immobilized onto the surface of the PANI film, and voltammetry was used to monitor the electrocatalytic reduction of hydrogen peroxide under diffusion-controlled conditions. Linear responses over the concentration range 2.5×10⁻⁴ to 5×10⁻³ M were observed. Spectroelectrochemistry was used to monitor the changes in UV-vis properties of HRP, before and after the catalysis of H₂O₂. The biosensor surface morphology was characterized by scanning electron microscopy (SEM) using PANI-doped screen-printed carbon electrodes (SPCEs) in the presence and absence of (i) peroxidase and (ii) peroxide. The SEM images showed clear modifications of the conducting film surface structure when doped with HRP, as well as the effect of hydrogen peroxide on the morphology of biosensor.     

Novel chemical synthesis of polypyrrole thin film electrodes for supercapacitor application

Present investigation describes the cost-effective, novel and simple chemical synthesis of polypyrrole (PPy) thin films for supercapacitor application. These PPy films are characterized by different techniques such as X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR) and scanning electron microscopy (SEM). The XRD pattern reveals the amorphous nature of PPy thin film, which is highly feasible for supercapacitors. Further, FTIR study confirms the formation of PPy. The surface morphological study exhibit the coverage of uniform and smooth morphology on thin film. The electrochemical supercapacitive properties of PPy thin films are evaluated using cyclic voltammetry (CV) in 0.5 M H₂SO₄ electrolyte, which exhibits the maximum specific capacitance of 329 Fg⁻¹ at the scan rate of 5 mV s⁻¹. Additionally, an equivalent series resistance (ESR) of PPy thin films is found to be 1.08 Ω using electrochemical impedance measurement.     

Elaboration and characterisation of PDMS-HTiNbO5 nanocomposite membranes

Poly(dimethylsiloxane) (PDMS)-HTiNbO₅ nanocomposite membranes with various HTiNbO₅ nanofiller content were prepared by melt intercalation. WAXS diffraction measurements and TEM observations have suggested that the HTiNbO₅ mineral was exfoliated in the PDMS matrix. The influence of the filler in the membrane was evaluated by water diffusion, gas permeation (CO₂, N₂, O₂, ethane and ethylene), toluene pervaporation and by CO₂ sorption measurements.A filler content of only 2 wt.% in PDMS-HTiNbO₅ nanocomposite membranes slows down the water diffusion significantly, and a filler content of 5 wt.% reduces also the permeability of the films for toluene. The addition of a filler content up to 10 wt.% do not significantly influences the gas permeability (P) except for CO₂. The PDMS matrix appears to be highly permeable and, therefore, a decreasing effect on P is only marked for a very high HTiNbO₅ content. This effect is more pronounced for CO₂, the P value of which decreases by 80% when the amount of nanofiller is 40 wt.%. The sorption measurements show that the interaction between CO₂ and PDMS is weak (isotherms agree with Henry’s law). The filler decreases the solubility of CO₂ in the films (S = 7.94 × 10⁻³ and S = 5.44 × 10⁻³ cm³ STPcm⁻³ film cmHg⁻¹ for PDMS and PDMS-HTiNbO₅ 40 wt.%, respectively).     

Sensing hydrogen peroxide involving intramolecular charge transfer pathway: A boronate-functioned styryl dye as a highly selective and sensitive naked-eye sensor

The synthesis, properties and applications of a novel boronate-functioned styryl dye, BSD, as a colorimetric sensor for hydrogen peroxide is presented. The dye displayed remarkable color change from colorless (λ_max = 391 nm) to deep red (λ_max = 522 nm) in the presence of H₂O₂ and the behavior could be rationalized by the chemoselective H₂O₂-mediated transformation of arylboronate to phenolate, resulting in the release of the merocyanine dye which featured with strong intramolecular charge transfer (ICT) absorption band. The absorption increment of merocyanine at λ_max = 522 nm (? = 87000 L mol⁻¹ cm⁻¹) is linear with the concentration of H₂O₂ in the range of 1.0 × 10⁻⁷-2.5 × 10⁻⁵ mol L⁻¹ with the detection limit of 6.8 × 10⁻⁸ mol L⁻¹ under optimum conditions. There is almost no interference by other species that commonly exist due to the specific deprotection of H₂O₂ towards arylboronate group on BSD. The chromogenic sensor has been applied to the detection of trace amounts of hydrogen peroxide in rain water.