Effects of synthesis-solvent on swelling and elastic properties of poly(N-isopropylacrylamide) hydrogels

Thermosensitive N-isopropylacrylamide (NIPA) hydrogels were synthesized by a free radical copolymerization with N,N′-methylenebisacrylamide (MBAA) in four solvents: water, ethanol, acetone and N,N-dimethylformamide. The swelling and elastic properties of the hydrogels were affected by the synthesis-solvents; the hydrogels (e.g. NIPA/MBAA = 1000/50 mol/m³-pre-gel solution) synthesized in water have smaller swelling volume and larger shear modulus at 10 °C than those synthesized in amphiphilic solvents. The network structure of hydrogels was estimated in terms of the conversion and two sorts of effective crosslinking density based on the Flory theory and the concentration of crosslinker. The hydrogels synthesized in water can have the microscopic inhomogeneous network arising from the entanglement of polymer chains, while the hydrogels synthesized in amphiphilic solvents can have the homogeneous network arising from the polymer concentration lower than the pre-gel solution and can be similar in network structure to the lightly crosslinked hydrogel synthesized in water.     

Collagen-based highly porous hydrogel without any porogen: Synthesis and characteristics

In this contribution we have developed a collagen-based highly porous hydrogel by neutralizing the grafted poly(acrylamide-co-acrylic acid) after gel formation. Preparation of the hydrogels involved free radical polymerization of a combination of hydrolyzed collagen, acrylic acid (AA), acrylamide (AAm) and distilled water, in appropriate amounts and contained a crosslinking agent called N,N′-methylene bisacrylamide (MBA). The chemical structure of the hydrogels was characterized by means of FTIR spectroscopy, DSC and TGA thermal methods. Morphology of the samples was examined by scanning electron microscopy (SEM). Systematically, the certain variables of the graft copolymerization were optimized to achieve maximum swelling capacity. The absorbency under load (AUL) and centrifuge retention capacity (CRC) were measured. The swelling ratio in various salt solutions was also determined and additionally, the swelling of hydrogels was measured in solutions with pH ranged 1-13. The synthesized hydrogel exhibited a pH-responsiveness character so that a swelling-collapsing pulsatile behavior was recorded at pH 2 and 8.     

Synthesis and Characterization of Hydrogels Based on Gamma Radiation Copolymerization of N‐isopropylacrylamide and Ethylene Glycol Dimethacrylate Monomers

Hydrogels based essentially on N‐isopropylacrylamide (NIPAAm) and different ratios of ethylene glycol dimethacrylate (EGDMA) monomer were synthesized by gamma radiation copolymerization. The thermal decomposition behavior of NIPAAm/EGDMA hydrogels was determined by thermogravimetric analysis (TGA). The effect of temperature and pH on the swelling behavior was also studied. The results showed that the ratio of EGDMA in the comonomer feeding solution has a great effect on the yield product, gel fraction and water content in the final hydrogel. In this regard, it was observed that the increase of EGDMA ratio decreased these properties. The TGA study showed that all the compositions of NIPAAm/EGDMA hydrogels displayed higher thermal stability than the hydrogel based on pure PNIPAAm hydrogel. The swelling kinetics in water showed that pure PNIPAAm and NIPAAm/EGDMA hydrogels reached equilibrium after 6 h. However, NIPAAm/EGDMA hydrogels show swelling in water lower than pure PNIPAAm. The results showed that the swelling character of pure PNIPAAm and NIPAAm/EGDMA hydrogels was affected by the change in temperature within the temperature range 25–40°C, and showed a reversible change in swelling in the pH range 4–7 depending on composition.     

Adsorption of Apollo reactive dyes on poly(N,N dimethylamino ethylmethacrylate) hydrogels

Poly(N,N-dimethylamino ethylmethacrylate) [P(DMAEMA)] hydrogels were prepared by irradiating the ternary mixtures of dimethylamino ethylmethacrylate (DMAEMA)/ethyleneglycol dimethacrylate (EGDMA)/water (H₂O) by γ-rays at ambient temperature. The swelling of four types of DMAEMA hydrogels in distilled water is higher than the swelling of these hydrogels in dye solutions. The value of equilibrium swelling of P(DMAEMA)1 hydrogel was 338% at pH 7.0 in distilled water, while it was 325% and 326% at pH 7.0 in Apollofix Red (AR) and Apollofix Yellow (AY) solutions, respectively. The adsorption capacity of P(DMAEMA)1 hydrogel was found to increase from 85 to 131 mg for AR g⁻¹ dry gel and from 58 to 111 mg for AY g⁻¹ dry gel with decreasing pH of the dye solutions.     

Influence of crosslinker and ionic comonomer concentration on glass transition and demixing/mixing transition of copolymers poly(N-isopropylacrylamide) and poly(sodium acrylate) hydrogels

Hydrogels based on N-isopropylacrylamide and sodium acrylate as ionic comonomer were synthesized by free radical polymerization in water using N,N′-methylenebisacrylamide as crosslinker and ammonium persulfate as initiator. The glass transition of dried copolymers poly(N-isopropylacrylamide) (PNIPA) and poly(sodium acrylate) (SA) gels and demixing/mixing transition of PNIPA-SA hydrogels swollen with increasing amounts of water were studied using conventional differential scanning calorimetry. In the crosslinked polymers, the glass transition linearly increases, and the transition range becomes broader, with increasing crosslinker content. Increasing content of ionic comonomer also produces an increase of glass transition temperature, which moves to higher temperatures with higher sodium acrylate fraction. The influence of chemical structure of PNIPA-SA hydrogels on the lower critical solution temperature (LCST) of PNIPA-SA/water mixtures during heating and cooling was quantified as function of the content of the crosslinker and the ionic comonomer, as well as water content of the hydrogel in the range from 95 to 70 wt%. At parity of water content, the LCST occurs at higher temperatures for gels containing higher amounts of sodium acrylate. Similarly, the introduction of N,N′-methylenebisacrylamide causes an increase of the LCST, which grows with increasing of crosslinking degree of the hydrogel.     

Taguchi optimized synthesis of collagen-g-poly(acrylic acid)/kaolin composite superabsorbent hydrogel

A novel biopolymer-based hydrogel composite was synthesized through chemical crosslinking by graft copolymerization of partially neutralized acrylic acid onto the hydrolyzed collagen. The Taguchi method, a robust experimental design, was employed for the optimization of the synthesis based on the swelling capacity of the hydrogels. This method was applied for the experiments and standard L16 orthogonal array with five factors and four levels. In the synthesis of the composite superabsorbent, N,N′-methylene bisacrylamide (MBA) as crosslinker, ammonium persulfate (APS) as initiator, acrylic acid (AA) as monomer, neutralization percent (NU), and collagen/kaolin weight ratio were used as important factors. From the analysis of variance of the test results, the most effective factor controlling equilibrium swelling capacity was obtained and maximum water absorbency of the optimized final product was found to be 674 g/g. The surface morphology of the gel was examined using scanning electron microscopy. Furthermore in this research, swollen gel strength of composite SAPs already swollen under realistic conditions (saline solution absorbency under load) was determined.     

Swelling and network parameters of crosslinked thermoreversible hydrogels of poly(N-ethylacrylamide)

Samples of Poly(N-ethylacrylamide) (PEA) have been synthesized by free radical polymerization in water using N,N′-methylene bis-acrylamide (BIS) as crosslinker. Hydrogels obtained by swelling them in water, 15 wt% KCl and 1 wt% sodium dodecyl sulphate (SDS) were examined by gravimetric, dimensional and compression-strain measurements to afford values of swelling ratio, polymer-solvent interaction parameters, elastic moduli and effective crosslinking density ν_e. Crosslinking inefficiency is evidenced by the low value (0.23) of ν_e relative to the theoretical crosslinking density ν_t based on the content of BIS in the synthesis. A small but finite extrapolated value of ν_e at ν_t = 0 is indicative of hydrophobic physical interactions. In water at 298 K increasing the content of BIS leads to a decrease in swelling and increases in values of elastic moduli and polymer-water interaction parameter. At a fixed content of BIS the values of ν_e and the elastic moduli exhibit an unusual increase with temperature, the crosslinking thus being thermally reversible. It is proposed that this results from a balance between hydrophobic interaction and breakage of hydrophilic hydrogen bonding. Although KCl in the medium decreases the swelling compared with that in water, the opposite effect occurs on incorporation of SDS, which is assumed to confer some polyelectrolyte character to the PEA chains. The finding, that these two swelling media reduce the values of ν_e and elastic moduli cf the value in water, has not been resolved satisfactorily.     

Biodegradable and pH-sensitive hydrogels: Synthesis by crosslinking of N,N-dimethylacrylamide copolymer precursors

Novel pH-sensitive hydrogels containing azoaromatic crosslinks were synthesized by the crosslinking of polymeric precursors. First, a reactive polymeric precursor was synthesized by copolymerization of N,N-dimethylacrylamide, N-tert-butylacrylamide, acrylic acid, and N-methacryloylglycylglycine p-nitrophenyl ester. The hydrogel was prepared in the second step by the reaction of the polymeric precursor with N,N′-(ω-aminocaproyl)-4,4′-diaminoazobenzene. The hydrogels were characterized by the network structure, (that is, content of crosslinks, unreacted pendent groups, and cycles), the equilibrium swelling ratio as a function of pH, modulus of elasticity in compression, and the degradability in vitro. The results obtained indicated that the hydrogel network structure strongly depends on the reaction conditions such as polymer concentration, and the ratio of the reactive groups during the crosslinking reaction. The swelling and mechanical properties of hydrogels can be controlled by the modification of polymer backbone structure and/or the crosslinking density. The rates of hydrogel degradation depended on their degree of swelling. The higher the degree of swelling, the higher the degradability. The properties of the hydrogels suggest that they have a potential as carriers for colon-specific drug delivery. © 1994 John Wiley & Sons, Inc.     

An enhanced immobilization of BSA biomolecule on anionic hydrogels: swelling and adsorption modeling

The three-dimensional structure of hydrogels plays a leading role in several areas of applications. The hydrogels are more and more used as systems of immobilized and controlled release of biomolecules in biotechnology and bio-pharmacy industries. To improve protein adsorption capacity in poly(acrylamide) hydrogels, maleic acid co-monomer was included into the reaction mixture during hydrogel synthesis. So, hydrogels of poly(acrylamide) and its copolymers with diprotic maleic acid were prepared by copolymerization and chemical crosslinking with N,N′-methylene bis-acrylamide. Swelling behavior in distilled water, in physiological saline and in bovine serum albumin (BSA) solutions was studied. Influence of initial BSA concentration on hydrogel swelling and BSA adsorption was investigated. The high amount of maleic acid present in the hydrogels has a significant effect on the swelling behavior and BSA adsorption. Results showed that the pH sensitivity of hydrogels resulted in the high amount of adsorbed BSA. The adsorption isotherms were described by Langmuir and Freundlich models. The thermodynamic parameter (ΔG _ads ⁰ ) was determined for all obtained hydrogels. We demonstrated the favorable character and reversibility of the BSA adsorption process.     

Modified carrageenan 3. Synthesis of a novel polysaccharide-based superabsorbent hydrogel via graft copolymerization of acrylic acid onto kappa-carrageenan in air

A novel biopolymer-based superabsorbent hydrogel was synthesized through chemically crosslinking graft copolymerization of acrylic acid (AA) onto kappa-carrageenan (κC), in the presence of a crosslinking agent and a free radical initiator. A proposed mechanism for κC-g-polyacrylic acid was suggested and the affecting variables onto graft polymerization (i.e. the crosslinker, the monomer and the initiator concentration, the neutralization percent and reaction temperature) were systematically optimized to achieve a hydrogel with swelling capacity as high as possible. Maximum water absorbency of the optimized final product was found to be 789 g/g. The swelling capacity of the synthesized hydrogels was also measured in various salt solutions. The time-temperature profile of the polymerization reaction, in order to investigate the effect of molecular oxygen was conducted in terms of the absence and presence of the atmospheric oxygen. The overall activation energy (E_a) of the graft polymerization reaction was found to be 2.93 KJ/mol.     

Network and thermodynamic properties of hydrogels of poly[1-(3-sulfopropyl)-2-vinyl-pyridinium-betaine]

Samples of poly[1-(3-sulfopropyl)-2-vinyl-pyridinium-betaine] (PSPV) have been synthesized to high conversion by free radical polymerization in aqueous solution of the zwitterionic monomer SPV with several concentrations of the crosslinker N,N′-methylene-bis-acrylamide (MBA). Hydrogels obtained by swelling them in water and aqueous KSCN solution were examined by gravimetric and dimensional analysis, and by compression-strain measurements. The derived effective crosslinking density ν_e was only ca. 11% of the theoretical value, indicating low efficiency of chemical crosslinking by MBA. At 298 K increasing content of MBA produces increases in the values of ν_e, elastic moduli and polymer-water interaction parameter χ. At a fixed MBA content, increasing temperature led to decreases in the values of ν_e, elastic moduli and χ, but an increase in water content of hydrogel. For swelling in aq. KSCN solution the mechanical properties are insensitive to content of salt. Experimental and theoretical analysis afforded values of the water/polymer, salt/water and salt/polymer interaction parameters. Where appropriate the findings are compared with those reported for a different zwitterionic hydrogel and a neutral non-zwitterionic hydrogel.     

Rapid swelling and deswelling in cryogels of crosslinked poly(N-isopropylacrylamide-co-acrylic acid)

Thermally sensitive hydrogels of poly[N-isopropylacrylamide (NIPA)-co-acrylic acid (AA)] hydrogels with N,N-methylene bisacrylamide (BIS) as crosslinker have been synthesized via a two-step procedure in which, the initial polymerisation is conducted for various times at 18 °C, this step being followed by polymerisation for one fixed time at −22 °C. The gravimetrically determined rates of swelling/deswelling for these materials termed “cryogels” prepared by this two-step polymerisation are much higher than those for the same type of hydrogel prepared via conventional methods (30 °C for 24 h). For example the time for the former xerogel to take up 70% of its final water content at 25 °C is just 18 min, compared with a time 300 min for the latter to attain the same uptake of water. During deswelling (shrinking) at 50 °C, which is above the lower critical temperature, the hydrogel loses 60 and 90 wt% water in 1 and 10 min respectively, compared to a timescale for the corresponding crosslinked copolymers prepared by conventional methods of about 100 min for 50 wt% water loss. A third type of hydrogel was made by a cold treatment (CT), for which the hydrogel prepared by conventional polymerization was stored in the frozen state. The swelling rate of these CT xerogels was the same as that for xerogels prepared by conventional polymerization, but the deswelling rate of the former was higher than that of the latter; for example, during deswelling, a loss of 90% water is attained within a few minutes.Scanning electron microscopy, digital photographs and flotation experiments together with swelling ratio studies reveal that the polymeric network of cryogel produced by the two-step polymerization method is characterized by an open structure with more pores and higher swelling ratio but lower mechanical strength compared to the conventional hydrogels. Such rapid response hydrogels have potential applications in separation and drug release technologies for example.     

Modeling of absorption kinetics of poly(acrylamide) hydrogels crosslinked by EGDMA and PEGDMAs

In this study, acrylamide-based hydrogels are synthesized by free radical solution polymerization in aqueous solution using ethylene glycol dimethacrylate (EGDMA) and its derivative polyethylene glycol dimethacrylate (PEGDMA) with different molecular weights as crosslinkers in the solution medium. The Fourier transform infrared spectroscopy technique is used for the structural characterization of the hydrogels. Dynamic swelling tests are conducted on acrylamide-based hydrogels for the determination of the swelling characteristics with respect to different crosslinking concentrations at room temperature. The parameters of swelling kinetics and diffusion mechanisms of the hydrogels are calculated with the aid of the data obtained. Accordingly, PEGDMA and EGDMA absorption capacity is found to increase with increasing concentrations. The lowest and highest water absorption capacities in PEGDMA₈₁₀ and EGDMA crosslinked hydrogels are 22.73–48.39 and 10.15–16.02 g/g, respectively. Water intake of hydrogels crosslinked by EGDMA and PEGDMAs followed Fickian nature type diffusion except for PEGDM₈₁₀, which has a swelling exponent greater than 0.5 and so does not follow a Fickian type of diffusion. PEGDM₈₁₀ showed the fastest diffusion rate of between 5.87 × 10^?4 and 10.87 × 10^?4 cm² s^?1.     

Synthesis and characterization of thermo-sensitive poly (N-isopropylacrylamide) hydrogel with fast response rate

Thermo-sensitive poly (N-isopropylacrylamide) (PNIPA) hydrogel with fast response rate was prepared by polymerizing N-isopropylacrylamide (NIPA) in an aqueous hydroxyl-propyl-methyl cellulose solution. The volume phase transition temperature of PNIPA hydrogels was characterized by differential scanning calorimetry (DSC), and the surface morphology was observed by scanning electron microscopy (SEM). The swelling ratios of the hydrogels at different temperatures were measured. Furthermore, the deswelling kinetics of the hydrogels was also studied by measuring their water retention capacity. In comparison with a conventional PNIPA hydrogel prepared in water, the hydrogel synthesized in aqueous hydroxyl-propyl-methyl cellulose solution has higher swelling ratios at temperatures below the lower critical solution temperature and exhibits a much faster response rate to temperature changes. For example, the hydrogel made in aqueous hydroxyl-propyl-methyl cellulose solution lost 89% water within 1 min and about 93% water in 4 min, whereas the conventional hydrogel lost only about 66% water in 15 min from the deswelling measurement in similar conditions. Translated from Chinese Journal of Applied Chemistry, 2006, 23(6): 581–585 (in Chinese)     

Crosslinking Parameter on the Preparation of Cellulose Based Hydrogel with Divynilsulfone

Polymeric hydrogels are crosslinked polymers which display high sorption capacity in water and water solution. In this work, cellulose based hydrogel was prepared with divinylsulfone as crosslinking agent. Cellulose based hydrogel was synthesized as a mixture of sodium salt of carboxymethylcellulose (CMCNa) and hydroxyethylcellulose (HEC). The effect of chemical composition, temperature and reaction time during crosslinking processes was investigated both the value of equilibrium water uptake and swelling ratio. Infrared spectra of the synthesized polymeric networks were studied to investigate the chemical structure of crosslinking reaction qualitatively. The thermal properties and morphology of the obtained cellulose based hydrogels were observed by means of TGA (thermo-gravimetry analysis) and SEM (scanning electron microscopy), respectively. Crosslinking of CMCNa/HEC polymeric network results in a decrease in thermal stability. Hydrogel with weight ratio of CMCNa/HEC 5 to 1 at reaction temperature of 60 °C gave the highest absorption capacity in distilled water.     

Studies on radiation synthesis of polyethyleneimine/acrylamide hydrogels

Polyethyleneimine(PEI)/acrylamide(AAM) hydrogels were synthesized by γ-radiation-induced polymerization/crosslinking of aqueous mixtures containing different ratios of PEI and AAM. The gel percentage and equilibrium degree of swelling (EDS) of the synthesized hydrogels were investigated. The compositions of the hydrogels produced were found to be different from the feed composition. Ion-chromatography technique was used to determine the amount of Pb (II) and Cd (II) absorbed by the hydrogel. The maximum binding capacity of the PEI/AAM hydrogels, for Pb and Cd was found to be 19 and 12.6 mg/g, respectively, (at 100 ppm). PEI/AAM hydrogels had better metal uptake efficiency than the pure AAM hydrogel at concentrations less than 50 ppm. Pure PEI was observed to be highly degrading type polymer on exposure to gamma radiation. TGA and FT-IR techniques were used to characterize the prepared hydrogels.     

Doublestimuli-responsive degradable hydrogels for drug delivery: Interpenetrating polymer networks composed of oligopeptide-terminated poly(ethylene glycol) and dextran

Biodegradable hydrogels composed of oligopeptide-terminated poly(ethylene glycol) (PEG) and dextran with interpenetrating polymer network (IPN) structure were proposed as a novel substrate for multistimuli-responsive drug delivery. IPN-structured hydrogels were synthesized by sequential crosslinking reactions of N-methacryloyl-glycilglycilglycil-terminated PEG and dextran. In vitro degradation of the IPN-structured hydrogels was examined using papain and dextranase as model enzymes for hydrolyzing the oligopeptide and the dextran. Specific degradation in the presence of papain and dextranase was observed in the IPN-structured hydrogel with a particular composition of PEG and dextran, whereas this hydrogel was not degraded by one of the two enzymes.     

Studies of sodium humate/polyacrylamide/clay hybrid hydrogels. I. Swelling and rheological properties of hydrogels

A type of novel hybrid hydrogels from sodium humate (SH), polyacrylamide (PAM), and hydrophilic Laponite clay were prepared using potassium persulfate (KPS) as the initiator and N,N′-methylenebisacrylamide (MBA) as the cross-linker. The structures of the hydrogels were characterized by field emission scanning electron microscope and FTIR. Their swelling properties, swelling mechanism and rheological properties were also investigated. Experiments show that the composite is heterogeneous in the PAM/SH hydrogel system, while the clay collaborates with SH and improves the network structure of PAM/SH/clay hydrogel. High water-absorbing capability is shown for both hydrogel systems. Han plot proves that clay and SH are compatible with PAM for PAM/SH/clay hydrogels.     

Uptake of Basic Blue 17 from aqueous solutions by using chemically crosslinked polyelectrolyte AAm/AASS hydrogels

In this study, the removal of a cationic thiazin dye such as Basic Blue 17 (Toluidin Blue, BB 17) by chemically crosslinked acrylamide (AAm)/acrylic acid sodium salt (AASS) hydrogels was investigated. Super water retainer AAm/AASS hydrogels with various compositions were prepared from ternary mixtures of AAm, AASS and water by free radical polymerization in aqueous solution using multifunctional crosslinkers such as ethylene glycol dimethacrylate (EGDMA), N,N′ methylenebisacrylamide (NMBA), 1,4 butanediol dimethacrylate (BDMA) and trimethylolpropane triacrylate (TMPTA). Adsorption of Basic Blue 17 from aqueous solutions was studied by batch sorption technique at 25^°C. The effect of Basic Blue 17 concentration and mass of adsorbent on the dye adsorption were examined. In the experiments of the sorption, C type and L type sorption in the Giles classification system was found. Some binding parameters such as initial binding constant (K _i ), equilibrium constant (K), monolayer coverage (n), site-size (u), and maximum fractional occupancy (Ô) for AAm/AASS hydrogel-dye binding system were calculated by using Klotz linearization method. Finally, the amount of sorbed Basic Blue 17 per gram of dry hydrogel (q) was calculated to be 1.96–21.35 μ mol dye per gram for AAm/AASS hydrogels. Adsorption of Basic Blue 17 was changed range 39.17–96.63%. AAm/AASS hydrogels crosslinked by TMPTA, EGDMA, BDMA or NMBA can be used a sorbent in biotechnology, environment, sorption, separation, purification, immobilization and enrichment of some species.     

Synthesis and network structure of ionic poly(N,N-dimethylacrylamide-co-acrylamide) hydrogels: Comparison of swelling degree with theory

At four different charge densities, ionic hydrogels based on N,N-dimethylacrylamide (DMAAm), acrylamide (AAm), and itaconic acid (IA) were synthesized by free-radical cross-linking copolymerization in water with N,N-methylenebis(acrylamide) (BAAm) as the cross-linker, ammonium persulfate (APS) as the initiator, and N,N,N′,N′-tetramethylenediamine (TEMED) as the activator. The swelling behaviors of these hydrogels were analyzed in buffer solutions at various pH. It was observed that the swelling behavior of cross-linked ionic poly(N,N-dimethylacrylamide-co-acrylamide) [P(DMAAm-co-AAm)] hydrogels at different pHs agreed with the modified Flory-Rehner equation based both on the phantom network and affine network models and the ideal Donnan theory. In addition, the kinetics of swelling of the hydrogels was studied in pH 2, 5 and 9 buffer solutions. The swelling curves exhibited the characteristic features of transport process, apparently the Fickian diffusion of fast rates.