The effect of gel layer thickness on the salt rejection performance of polyelectrolyte gel-filled nanofiltration membranes

The effect of gel layer thickness on salt separation of positively charged pore-filled nanofiltration membranes has been examined both theoretically and experimentally. The extended Nernst-Planck (ENP) equation coupled with the Teorell-Meyer-Sievers (TMS) model were used to calculate the pressure-driven sodium chloride rejections for membranes having gel densities in the range typically used in nanofiltration applications. It was found that salt rejection was dependent on membrane (gel-layer) thickness with salt rejections increasing rapidly with thickness up to 50–75 μm. Further increases in thickness beyond this point had a much smaller effect on salt rejection. The theoretical predictions were examined experimentally by preparing a series of membranes with cross-linked poly(3-acrylamidopropyl)-trimethylammonium chloride (PAPTAC) gels with varying densities within the pores of a thin microporous polyethylene (PE) support. The membranes were characterized by their polymer volume fractions (gel concentration), thicknesses and effective charge densities. The effect of membrane thickness was examined by using single and stacks of two membranes. The pure water fluxes and salt rejections of the membranes and membrane stacks were determined in the pressure range 50–550 kPa. The single salt rejections of the membranes which were very dependent on the thickness of the membrane or membrane stack, were fully in accord with the calculated salt rejections of the membranes.     

Theory of pressure-driven transport of neutral solutes and ions in porous ceramic nanofiltration membranes

Hindered transport theory and homogeneous electro-transport theory are used to calculate the limiting, high volume flux, rejection of, respectively, neutral solutes and binary electrolytes by granular porous nanofiltration membranes. For ceramic membranes prepared from metal oxides it is proposed that the membrane structural and charge parameters entering into the theory, namely the effective pore size and membrane charge density, can be estimated from independent measurements: the pore radius from the measured hydraulic radius using a model of sintered granular membranes and the effective membrane charge density from the hydraulic radius and the electrophoretic mobility measurements on the ceramic powder used to prepare the membrane. The electro-transport theory adopted here is valid when the membrane surface charge density is low enough and the pore radius is small enough for there to be strong electrical double layer overlap in the pores. Within this approximation the filtration streaming potential is also derived for binary electrolytes.     

Effect of solution chemistry on the surface charge of polymeric reverse osmosis and nanofiltration membranes

A streaming potential analyzer has been used to investigate the effect of solution chemistry on the surface charge of four commercial reverse osmosis and nanofiltration membranes. Zeta potentials of these membranes were analyzed for aqueous solutions of various chemical compositions over a pH range of 2 to 9. In the presence of an indifferent electrolyte (NaCl), the isoelectric points of these membranes range from 3.0 to 5.2. The curves of zeta potential versus solution pH for all membranes display a shape characteristic of amphoteric surfaces with acidic and basic functional groups. Results with salts containing divalent ions (CaCl₂, Na₂SO₄, and MgSO₄) indicate that divalent cations more readily adsorb to the membrane surface than divalent anions, especially in the higher pH range. Three sources of humic acid, Suwannee River humic acid, peat humic acid, and Aldrich humic acid, were used to investigate the effect of dissolved natural organic matter on membrane surface charge. Other solution chemistries involved in this investigation include an anionic surfactant (sodium dodecyl sulfate) and a cationic surfactant (dodecyltrimethylammonium bromide). Results show that humic substances and surfactants readily adsorb to the membrane surface and markedly influence the membrane surface charge.     

Preparation and characterization of nanofiltration membranes by coating polyethersulfone hollow fibers with sulfonated poly(ether ether ketone) (SPEEK)

A new type of nanofiltration membrane is reported based on coating a sulfonated poly(ether ether ketone) (SPEEK) layer on top of a polyethersulfone support. The membranes were characterized by dextran mixtures, salt solutions as well as negatively charged dyes. The SPEEK coated nanofiltration membranes showed molecular weight cutoff for dextran in the range of ultrafiltration, however, rather high rejection for sodium sulfate; retention for salts in the order of RNa₂SO₄>RNaCl>RMgCl₂$R_{\text{N}{\text{a}}_2\text{S}{\text{O}}_4}>R_{\text{NaCl}}>R_{\text{MgC}{\text{l}}_2}$; in addition, the membranes showed a 97–100% retention to the organic dyes. The rejection rates were improved by an increase in the coating thickness and the polymer concentration in the coating solution at the penalty of permeability decrease. Furthermore, it was found that pore penetration of SPEEK into the support membrane effectively constrained the swelling rate of SPEEK and increased the retention. The Donnan–Steric Pore Model was used to describe the transport properties of the membrane. Modeling identified a very tortuous passage within the active separation layer.     

Glass transition of polymers confined to nanoporous glasses

The glassy dynamics of poly(propylene glycol) (PPG) and poly(methyl phenyl siloxane) (PMPS) confined to nanoporous glasses (pore sizes 2.5–20 nm) investigated by dielectric spectroscopy, temperature modulated DSC and neutron scattering is compared. For both systems the relaxation rates estimated from dielectric spectroscopy and temperature modulated DSC agree quantitatively indicating that both experiments sense the glass transition.For PPG the glassy dynamics in nanopores is determined by a counterbalance of an adsorption and a confinement effect where the temperature dependence of the relaxation times obeys the Vogel/Fulcher/Tammann (VFT-) equation. The former effect results from an interaction of the confined macromolecules with the internal surfaces which in general slows down the molecular dynamics. A confinement effect leads to an acceleration of the segmental dynamics compared to the bulk state and points to an inherent length scale on which the glassy dynamics takes place. The step of the specific heat capacity c_p at the glass transition vanishes at a finite length scale of 1.8 nm. This result supports further the conception that a characteristic length scale is relevant for glassy dynamics.For PMPS down to a pore size of 7.5 nm the temperature dependence of the relaxation times follows the VFT-dependence and a confinement effect is observed like for PPG. At a pore size of 5 nm this changes to an Arrhenius-like behavior with a low activation energy. At the same pore size c_p vanishes for PMPS. This points to a dramatic change in the character of molecular motions responsible for glassy dynamics and supports further the relevance of a characteristic length scale on which it takes place.Quasielastic neutron scattering experiments on PMPS reveal that the microscopic dynamics characterized by the mean square displacement depends on confinement above the glass transition. The diffusive character of the relevant molecular motions seems to disappear at a length scale of about 1.6 nm.     

Fine structure and formation mechanism of particulate phase‐inversion poly(vinylidene fluoride) membranes

The structure and formation mechanism of a microporous phase‐inversion poly(vinylidene fluoride) (PVDF) membrane exhibiting a relatively loosely packed agglomerate of semicrystalline globules are explored. The membrane has been prepared by the coagulation of a solution of PVDF in dimethylformamide by the action of 1‐octanol, which is a soft nonsolvent. Experimental observations pertain to the globule surface, which is dominated by a grainy nanostructure; the globular interior, which exhibits a range of fine structures (e.g., twisted sheets and treelike branches); and the globule–globule connections, which exhibit a sheetlike or ropelike structure. On the basis of the observed structural details and phase diagram considerations, it is proposed that the membrane structure is the result of a unique combination of a polymer crystallization and a liquid–liquid phase‐separation process, with end‐result globular structural features of remarkable uniformity. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1578–1588, 2003     

Structure formation of integral-asymmetric membranes of polystyrene-block-Poly(ethylene oxide)

For the first time the combination of solution casting and solvent–nonsolvent exchange (phase inversion) has been applied to generate asymmetric membranes with highly ordered hexagonally packed cylinders with perpendicular orientation composed of polystyrene-block-poly(ethylene oxide). The influence of parameters like solvent composition and evaporation time on the membrane formation is presented. The development is based on a study of the solution behavior by dynamic light scattering and the precipitation behavior of the cylinder forming diblock copolymer by turbidity measurements from different solvent and nonsolvent systems. The water flux properties, as an important membrane characteristic, show a time dependent behavior, due to swelling of the polyethylene oxide blocks. The morphologies of the membranes are imaged by scanning electron microscopy. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2013     

Ultrasensitive electrochemical immunosensor for zeranol detection based on signal amplification strategy of nanoporous gold films and nano-montmorillonite as labels

Nano-montmorillonites belong to aluminosilicate clay minerals with innocuity, high specific surface area, ion exchange, and favorable adsorption property. Due to the excellent properties, montmorillonites can be used as labels for the electrochemical immunosensors. In this study, nano-montmorillonites were converted to sodium montmorillonites (Na-Mont) and further utilized for the immobilization of thionine (TH), horseradish peroxidase (HRP) and the secondary anti-zeranol antibody (Ab₂). The modified particles, Na-Mont-TH-HRP-Ab₂ were used as labels for immunosensors to detect zeranol. This protocol was used to prepare the immunosensor with the primary antibody (Ab₁) immobilized onto the nanoporous gold films (NPG) modified glassy carbon electrode (GCE) surface. Within zeranol concentration range (0.01–12 ng mL⁻¹), a linear calibration plot (Y = 0.4326 + 8.713 X, r = 0.9996) was obtained with a detection limit of 3 pg mL⁻¹ under optimal conditions. The proposed immunosensor showed good reproducibility, selectivity, and stability. This new type of immunosensors with montmorillonites and NPG as labels may provide potential applications for the detection of zeranol.     

Synthesis and characterization of asymmetric polyethersulfone membranes: effects of concentration and polarity of nonsolvent additives on morphology and performance of the membranes

In this study, effects of methanol, ethanol and 1‐propanol as variable nonsolvent additives (NSAs) on the morphology and performance of flat sheet asymmetric polyethersulfone (PES) membranes were investigated. The membranes were prepared from PES/Polyvinylpyrrolidone (PVP)/N‐methyl‐2‐pyrrolidone (NMP) system via phase inversion. The obtained results indicate that with the addition of NSAs to the casting solution, the membrane morphology changes slowly from macrovoids to an asymmetric structure with finger‐like pores. By increasing the NSAs concentrations in the casting solution and decreasing their polarities, the membrane structure changes from finger‐like pores to sponge. The AFM and SEM images reveal that addition of NSA to the casting solution decreases the pore size of the prepared membranes and reduces the pure water flux and BSA solution flux, while increasing the protein rejection. Surface analysis of the membranes showed that mean pore size and surface porosity of the prepared membranes with NSAs in the casting solution are smaller compared with those of the membrane prepared with no NSA. Pure water flux and BSA solution flux through the membranes decrease and BSA rejection increases with increase in the concentration of NSAs and decrease in their polarity. Finally, it can be concluded that the T_g values of the PES membranes increase by addition of NSAs to the casting solution. Copyright © 2009 John Wiley & Sons, Ltd.     

Fabrication and development of interfacial polymerized thin-film composite nanofiltration membrane using different surfactants in organic phase; study of morphology and performance

The effects of addition of cationic cetyltrimethylammonium bromide (CTAB), non-ionic (Triton X-100) and anionic sodium dodecyl sulfate (SDS) surfactants in organic phase for preparing the composite nanofiltration membranes were investigated. The interfacial polymerization technique was employed by applying trimesoyl chloride (TMC) and piperazine (PIP) as the reagents for the preparation of poly(piperazineamide) on a UF support. The obtained thin layer membranes were placed in oven for 2 min at 70 °C. Water permeation performance, salt rejection, membrane surface charge, chemical structure and membrane morphology including top surface and cross-section were investigated for characterization of the prepared membranes using IR-ATR, SEM, filtration and zeta potential measurement. The prepared membranes using SDS showed higher flux compared to the other membranes. SEM surface images demonstrate some defects and cracks on the thin layer surface of the membrane prepared with SDS. For membrane containing CTAB, the salt rejection increased in the order of Na₂SO₄ > NaCl > MgCl₂ with variation around 50–90%.     

Influence of non-reactive solvent on optical performance, photopolymerization kinetics and morphology of nanoporous polymer gratings

A study of nanoporous polymer gratings, with controllable nanostructured porosity, as a function of grating performance, photopolymerization kinetics and morphology is presented. Modifying the standard holographic polymer dispersed liquid crystal (H-PDLC) system, by including a non-reactive solvent, results in a layered, nanoporous morphology and produces reflective optical elements with excellent optical performance of broadband reflection. The addition of the non-reactive solvent in the pre-polymer mixture results in a morphology typified by void/polymer layer-by-layer structures if sufficient optical energy is used during the holographic writing process. The duration and intensity of optical exposure necessary to form well-aligned nanoporous structures can only be obtained in the modified system by (a) illumination under longer time of holographic interference patterning (30 min) or (b) illumination under very short time of holographic interference patterning (30 s) and followed by post-curing using homogeneous optical exposure for 60 min. Comparatively, a typical H-PDLC is formed in less than 1 min. To further understand the differences in the formation of these two analogous materials, the temporal dynamics of the photoinitiation and polymerization (propagation) kinetics were examined. It is shown herein that the writing exposure gives a cross-linked polymer network that is denser in the bright regions. With 60% (or even 45%) acrylate conversion, almost no free monomer would be left after the writing. Continued exposure serves primarily to add cross-links. This has the tendency to collapse the network, especially the less dense portions, which in effect get glued down to the more dense parts. To the extent that the solvent increases the mobility of the polymer network, this process will be aided. Equally important, the size of the periodic nanopores can be varied from 10 to 50 nm by controlling either the LC concentration in the pre-polymer mixture or by controlling the time of the homogeneous post-cure.     

Fabrication of free-standing nanoporous silver by selectively dissolving gold from gold–silver alloys via a novel converse dealloying method

A novel converse dealloying method was developed to fabricate free-standing nanoporous silver (np-Ag). One remarkable characteristic of the new dealloying method is that inert component (Au) is selectively removed from Au–Ag alloys while active component (Ag) is left undissolved. Thiourea plays a key role in the formation of a free-standing porous Ag framework since it not only leads to anodic dissolution of Au component but also causes the surface passivation of Ag component. Because of the excellent electrocatalytic activity toward the reduction of trichloroacetic acid (TCA), the as-prepared np-Ag materials can be directly used as working electrodes to detect TCA in the concentration range from 2.50 to 25.0 mM.     

Electrochemical immunoassay of hepatitis B surface antigen by the amplification of gold nanoparticles based on the nanoporous gold electrode

We describe herein the combination of electrochemical immunoassay using nanoporous gold (NPG) electrode with horseradish peroxidase (HRP) labeled secondary antibody-gold nanoparticles (AuNPs) bioconjugates for highly sensitive detection of protein in serum. The electroactive product of o-phenylenediamine (OPD) oxidized with H₂O₂ catalyzed by HRP was reduced in the Britton-Robinson (BR) buffer and the peak current of which was used to determine the concentration of antigen (Ag) in the analyte. The active surface area of NPG electrode was larger than that of a bare flat one. The presence of AuNPs enhanced the immobilized amount of HRP labeled antibody (Ab), which improved the sensitivity of the immunoassay when used as the secondary antibodies. As a result of these two combined effects, the sensitivity of the immunoassay for the determination of target protein was increased significantly. Using hepatitis B surface antigen (HBsAg) as a model, we demonstrate a dose response in the range of 0.01-1.0 ng/mL with a detection limit of 2.3 pg/mL. Analytical results of several human serum samples obtained using the developing technique are in satisfactory agreement with those given by enzyme-linked immune-absorbent assays (ELISA). In addition, the technique was about 100 times more sensitive in the detection of HBsAg than ELISA. All these demonstrated the feasibility of the present immunoassay method for clinical diagnosis.     

Performance and pore characterization of nanoporous carbon membranes for gas separation

The performance of a novel nanoporous carbon membrane for separation of hydrogen-hydrocarbon gas mixtures is described. The membrane selectively adsorbs hydrocarbons from hydrogen at the high pressure side and the adsorbed molecules then diffuse along the pore walls to the low pressure side. Pressure levels at thigh gh and low pressure sides of the membrane and the type and flow rate of the sweep gas at the low pressure side of the membrane were varied. The effects of these variables on the hydrogen recovery and hydrocarbon rejection by the membrane were investigated.     

High performance of PES-GNs MMMs for gas separation and selectivity

In this study, graphene nanosheets (GNs) were incorporated into polyethersulfone (PES) by phase inversion approach for preparing PES-GNs mixed matrix membranes (MMMs). To investigate the impact of filler content on membrane surface morphology, thermal stability, chemical composition, porosity and mechanical properties, MMMs were constructed with various GNs loadings (0.01, 0.02, 0.03, and 0.04 wt%). ?The performance of prepared MMMs was tested for separation and selectivity of CO₂, N₂, H₂ and CH₄ gases at various pressures from 1 to 6 bar and temperature varying from 20 to 60 °C. It was observed that, compared to the pristine PES membrane, the prepared MMMs significantly improved the gas separation and selectivity performance with adequate mechanical stability. The permeability of CO₂, N₂, H₂ and CH₄ for the PES + 0.04 wt% GNs increases from 9 to 2246, 11 to 2235, 9 to 7151, and 3 to 4176 Barrer respectively, as compared with pure PES membrane at 1 bar and 20 °C due to improving the membrane absorption and porosity. In addition, by increasing the pressure, the permeability and selectivity of CO₂, N₂, H₂ and CH₄ are increased due to the increased driving force for the transport of gas via membranes. Furthermore, the permeability of CO₂, N₂, H₂ and CH₄ increased by increasing the temperature from 20 to 60 °C due to the plasticization in the membranes and the improvement in polymer chain movement. This result proved that the prepared membranes can be used for gas separation applications.     

Preparation and characterization of asymmetric polyethersulfone (PES) membranes

Flat‐sheet asymmetric polyethersulfone (PES) membranes were prepared from polyethersulfone (PES)/ polyethylene glycol (PEG)/ N‐methyl‐2‐pyrrolidone (NMP) system via phase inversion induced by immersion precipitation in water coagulation bath. Effects of propionic acid (PA) as a non‐solvent additive (NSA) on morphology and performance of the membranes prepared from PES/PEG 6000/NMP system in water coagulation bath were investigated. The cross section morphology of the membranes was studied by scanning electron microscopy (SEM). In addition, performance of the membranes was studied by water content measurements and separation experiments using pure water and human serum albumin (HSA) protein solution as feeds. According to SEM analysis, it was found out that the NSA has a significant influence on the structure of the skin layer and the sublayer. The obtained results indicated that addition of PA to the casting solution decreases permeation flux of the prepared membranes. Copyright © 2009 John Wiley & Sons, Ltd.     

新型荧光分子印迹膜特异性识别和检测目标蛋白质

制备了一种新型荧光分子印迹膜(L-半胱氨酸修饰的量子点嵌入的分子印迹膜(QDs@MIM)),并将其作为荧光人工受体用于目标蛋白质(溶菌酶)的特异性识别和检测。QDs@MIM以溶菌酶为模板分子、丙烯酰胺为功能单体、L-半胱氨酸修饰的量子点为辅助单体、N,N′-亚甲基双丙烯酰胺为交联剂,在预硅烷化的玻璃板上制备而成。在最佳条件下,QDs@MIM对溶菌酶检测的线性范围为0.1~1.0μmol/L,吸附平衡时间为4 min,选择性因子为6.2。该方法操作简单、吸附平衡时间短、选择性高,具备作为生物传感器快速分析样品中目标蛋白质的潜力。     

Effect of pyrolysis temperature and operating temperature on the performance of nanoporous carbon membranes

Technology designed to capture and store carbon dioxide (CO₂) will play a significant role in the near-term reduction of CO₂ emissions and is considered necessary to slow global warming. Nanoporous carbon (NPC) membranes show promise as a new generation of gas separation membranes suitable for CO₂ capture.We have made supported NPC membranes from polyfurfuryl alcohol (PFA) at various pyrolysis temperatures. Positron annihilation lifetime spectrometry (PALS) and wide angle X-ray diffraction (WAXD) results indicate that the pore size decreases whilst the porosity increases with increasing pyrolysis temperature. The membrane performance results support these findings with a significant increase in permeance being seen with increasing pyrolysis temperature, which relates to the increase in porosity.Mixed gas performance measurements also show an increase in CH₄ permeance as the operating temperature is increased from 35 to 200 °C, which can be related to an increase in the rate of diffusion. However, the selectivity decreases with increasing operating temperature due to the smaller changes in the CO₂ permeance. These smaller changes in CO₂ permeance can be related to the stronger adsorption of this gas on the carbon surface at lower operating temperatures. Interestingly, regardless of the original pyrolysis temperature, the selectivity at higher operating temperatures is similar, whereas the permeance remains related to this pyrolysis temperature.     

固相萃取-高效液相色谱法测定地表水中的苯并三唑和苯并噻唑

建立了固相萃取-高效液相色谱分析地表水中苯并噻唑、苯并三唑、5-甲基-苯并三唑、5-氯-苯并三唑及5,6-二甲基-苯并三唑的方法。地表水样品采用HLB固相萃取柱富集净化后,在甲醇-水(55:45, v/v)流动相中用ZORBAX SB-C18色谱柱(250 mm×4.6 mm, 5 μm)分离,紫外检测,外标法定量。结果表明,5种目标化合物在0.064～80 mg/L范围内均呈良好的线性关系,线性相关系数均大于0.9999,仪器检出限为1.9～3.2 μg/L。空白自来水样中的加标回收率为87.8%～125.6%,相对标准偏差(n=3)为0.4%～9.4%。应用该方法测定了大连自来水及辽河入海口水样,在辽河入海口地表水中检出苯并噻唑、苯并三唑、5-甲基-苯并三唑、5-氯-苯并三唑。     

Molecular elucidation of morphology and mechanical properties of PVDF hollow fiber membranes from aspects of phase inversion, crystallization and rheology

This study explores the fundamental science of fabricating poly(vinylidene fluoride) (PVDF) hollow fiber membranes as well as elucidates the correlation among membrane morphology, crystallinity and mechanical properties as functions of non-solvent additives and dope rheology in the phase inversion process. A series of non-solvents (i.e. water, methanol, ethanol, isopropanol) are used either as non-solvent additives in the dope or as a component in the external coagulant. Depending on the strength of the non-solvent, the phase inversion of semi-crystalline PVDF membranes is dominated by liquid–liquid demixing or solid–liquid demixing accompanying crystallization. As a result, the membrane morphology transforms from an interconnected-cellular type to an interconnected-globule transition type with lower mechanical strengths when adding water, methanol, ethanol, or isopropanol into the spinning dopes or into the coagulation bath. The crystallinity and size of spherulitic globules in the morphology are controlled by the amounts of non-solvents presented in the systems. The rheological behavior of dope solutions is explored and the relationship between elongation viscosity and mechanical properties has been elaborated. Analytical methods and molecular dynamics simulations are employed to provide insights mechanisms from the views of thermodynamic and kinetic aspects as well as the state of polymer chains involved in the phase inversion process.