Nanocomposites of natural rubber and polyaniline-modified cellulose nanofibrils

Cellulose nanofibrils (CNF) were isolated from cotton microfibrils (CM) by acid hydrolysis and coated with polyaniline (PANI) by in situ polymerization of aniline onto CNF in the presence of hydrochloride acid and ammonium peroxydisulfate to produce CNF/PANI. Nanocomposites of natural rubber (NR) reinforced with CNF and CNF/PANI were obtained by casting/evaporation method. TG analyses showed that coating CNF with PANI resulted in a material with better thermal stability since PANI acted as a protective barrier against cellulose degradation. Nanocomposites and natural rubber showed the same thermal profiles to 200 °C, partly due to the relatively lower amount of CNF/PANI added as compared to conventional composites. On the other hand, mechanical properties of natural rubber were significantly improved with nanofibrils incorporation, i.e., Young’s modulus and tensile strength were higher for NR/CNF than NR/CNF/PANI nanocomposites. The electrical conductivity of natural rubber increased five orders of magnitude for NR with the addition of 10 mass% CNF/PANI. A partial PANI dedoping might be responsible for the low electrical conductivity of the nanocomposites.     

原位聚合法制备聚酰胺/聚苯胺复合导电纤维

研究了原位聚合法制备聚酰胺/聚苯胺导电纤维,并对制备的复合纤维进行红外及光学显微镜测试,结果表明聚苯胺与纤维成功复合。对制备的复合纤维进行电导率测试,采用控制单一变量法探讨了苯胺单体在不同的条件下聚合对纤维电导率的影响,并讨论了反应温度对聚合过程和电导率的影响,得出最佳的工艺条件为:纤维经30%的甲酸溶液预处理20min,苯胺单体浓度为0.8M,氧化剂过硫酸铵浓度为1M,掺杂酸为盐酸,浓度为0.8M,冰水浴条件,反应时间为4h,得到的聚酰胺/聚苯胺导电纤维的电导率为3.7S/m。     

Preparation and characterization of polyaniline/manganese dioxide composites and their catalytic activity

This paper is devoted to the preparation of polyaniline/MnO2 (PANI/MnO2) composites via chemical oxidation of aniline in H2SO4 medium using beta-MnO2 as an oxidant. The parameters affecting the polymerization reaction are considered. These parameters are [aniline], amount of beta-MnO2, stirring time, and polymerization temperature. SEM, FT-IR, XRD, and TGA techniques are used to characterize the resulting composites. XRD measurements reveal the distortion of the crystal structure of beta-MnO2 after the polymerization reaction. Thus, the XRD pattern of PANI is predominating. The crystalline composites are obtained using higher molar ratio of [Ox]/[ANI] and at higher temperature. Increasing the amount of beta-MnO2 led to an increase in the acidic character of the obtained composites due to adsorption of excess H+ on the oxide surface. The thermal stability of the composites decreased with increasing both [aniline] and stirring time, while it increased with increasing amount of beta-MnO2. The applications of the composites in the oxidative degradation of Direct Red 81, Acid Blue 92, and Indigo Carmine dyes exhibited good catalytic activity in the presence of H2O2 as an oxidant. The reactions followed first-order kinetics and the rate constants were determined. The degradation reaction involved the catalytic action of the PANI counterpart of the composite toward H2O2 decomposition, which can lead to the generation of HO radicals as a highly efficient oxidant attacking the target dyes. The detailed kinetic studies and the mechanism of these catalytic reactions are under consideration in our group.     

Thermal stability of several polyaniline/rare earth oxide composites (I): polyaniline/CeO<Subscript>2</Subscript> composites

Polyaniline (PANI)/CeO₂ composites were prepared by adding CeO₂ powder into the polymerization reaction mixture of aniline. Fourier transform infrared spectra (FTIR) and X-ray diffraction (XRD) were used to characterize the composites. Thermogravimetry (TG) and derivative thermogravimetry (DTG) were used to study the thermal stability of the composites. IR and XRD results show that interaction exists between PANI and CeO₂. This interaction maybe is hydrogen bonding action between the hydroxyl groups on the surface of the CeO₂ and the imine groups in the PANI molecular chains. TG–DTG analysis indicates that the thermal stability of the composites is higher than that of the pure PANI. The improvement in the thermal stability of the composites is attributed to the interaction between PANI and CeO₂, which restricts the thermal motion of PANI chains and shields the degradation of PANI in the composites.     

Coating of multiwalled carbon nanotubes with polymer nanospheres through microemulsion polymerization

We report a simple and noncovalent method for coating multiwalled carbon nanotubes (MWCNTs) with polyaniline (PANI) nanospheres using a microemulsion polymerization method. In this method, aniline polymerization is performed with MWCNTs in the presence of sodium dodecyl sulfate (SDS), which serves as both a surfactant and a dopant. Morphological, structural, thermal, and electrical properties of MWCNT–PANI nanocomposites were analyzed. The TEM results of the nanocomposites prepared with surfactant reveal that 30–50-nm-diameter PANI nanospheres were coated on the surface of the MWCNTs. Composites prepared without surfactant were found to be in core–sheath-type cable structures. The conductivities of the nanocomposites synthesized through microemulsion polymerization were found to be one order of magnitude higher than both the conductivities of pure PANI and the composites prepared via in situ chemical polymerization without an assisting SDS surfactant. The mechanism for the formation of nanostructured composites is presented.     

Synthesis and characterization of red mud/polyaniline composites: Electrical properties and thermal stability

New types of conducting composites using red mud as an inorganic substrate and polyaniline as the conducting phase were prepared. Red mud/polyaniline (RM/PANI) composites were synthesized in acidic aqueous solution by the chemical oxidative polymerization of aniline using ammonium peroxydisulfate as the oxidant. The composites exhibit conductivities in the 0.42-5.2 S cm⁻¹ range, depending on the amount of polyaniline. They were characterized by infrared and UV-vis spectroscopy, scanning electron microscopy and X-ray diffraction. The IR and X-ray results show that PANI is deposited on the RM surface. The composites have a globular structure and the PANI globules synthesized on the surface of RM are smaller than those prepared under the same conditions without the substrate. Thermogravimetric analysis was used for investigation of the thermal stability of the composites. The thermal stability of the conductivity of RM/PANI composites was studied by ageing at 125 °C, the conductivity being measured in situ during this process.     

Composites of polyaniline and lead dioxide: preparation,characterization, and catalytic activity

This paper is devoted to the preparation of polyaniline/lead dioxide composites (PANI/PbO₂) via chemical oxidation of aniline in H₂SO₄ medium using β-PbO₂ as an oxidant. The parameters affecting the polymerization reaction are considered. These parameters are [aniline], amount of β-PbO₂, stirring time, and different acids. The prepared composites were characterized by SEM, FT-IR, XRD, TGA, DTA, and elemental analysis. From XRD and FT-IR spectra, it was concluded that high molecular weight polymer could be obtained with high aniline concentration, high amount of β-PbO₂, increasing polymerization time and polymerization of ANI at lower temperatures. Thermogravimetric study exhibited that the composite prepared using high amount of β-PbO₂ has a higher thermal stability. The application of the composites in the oxidative degradation of Alizarin yellow G and Acid alizarin violet N dyes exhibited good catalytic activity in presence of H₂O₂ as an oxidant. The reactions followed first-order kinetics and the rate constants were determined.     

Synthesis, characterization and thermal analysis of polyaniline/ZrO2 composites

Conducting polyaniline-zirconium dioxide (PANI/ZrO₂) composites were synthesized by ‘in situ’ deposition technique in the presence of hydrochloric acid (HCl) as dopant by adding the fine grade powder (average particle size of approximately 20 nm) of ZrO₂ into the polymerization reaction mixture of aniline. The composites obtained were characterized by infrared spectra (IR) and X-ray diffraction (XRD) and thermogravimetric analysis (TGA). TG curves and DTG curves of the composites suggest that the thermal degradation process of PANI/ZrO₂ composites proceeds in two-steps and the composites are more thermally stable than that of the pure PANI. The improvement in the thermal stability for the composites is attributed to the interaction between PANI and ZrO₂, which restricts the thermal motion of PANI chains and shields the degradation of PANI in the composites.     

Electrical Properties Investigation in PA12/PANI Composites

Summary: Volume conducting PA-12 based composites powders were chemically prepared by in situ polymerization and aniline doping at room temperature. These kinds of polyamide / PANI composites were investigated regarding their electrical properties. Their ac and dc electrical properties measured in the frequency range of 10⁻²–10⁷ Hz are reported and the frequency dependence of electrical conductivity was investigated as a function of PANI concentration leading to the determination of the conductivity. The experimental conductivity was found to increase continuously with PANI content and explained by percolation theory with a relatively low percolation threshold of about 0.4 wt.%. The dielectric behavior of various PANI polymer composites has been characterized by the critical frequency ω_c (denoting the crossover from the dc plateau of the conductivity to its frequency dependent ac behaviour). Modelling the conductivity behavior versus volume fraction using Slupkowski approach has revealed that the considered parameters are not sufficient to describe the electrical conductivity behavior.     

Conductive Nanocomposites Based on Cellulose Nanofibrils Coated with Polyaniline-DBSA Via In Situ Polymerization

Summary: Cellulose nanofibrils (CNF) were extracted by acid hydrolysis from cotton microfibrils and nanocomposites with polyaniline doped with dodecyl benzenesulphonic acid (PANI-DBSA) were obtained by in situ polymerization of aniline onto CNF. The ratios between DBSA to aniline and aniline to oxidant were varied in situ and the nanocomposites characterized by four probe DC electrical conductivity, ultraviolet-visible-near infrared (UV-Vis - NIR) and Fourier-transform infrared (FTIR) spectroscopies and X-ray diffraction (XRD). FTIR and UV-Vis/NIR characterization confirmed the polymerization of PANI onto CNF surfaces. Electrical conductivity of about 10⁻¹ S/cm was achieved for the composites; conductivity was mostly independent of DBSA/aniline (between 2 and 4) and aniline/oxidant (between 1 and 5) molar ratios. X-ray patterns of the samples showed crystalline peaks characteristic of cellulose I for CNF samples, and a mixture of both characteristic peaks of PANI and CNF for the nanocomposites. Field emission scanning electron microscopy (FESEM) characterization corroborated the abovementioned results showing that PANI coated the surface of the nanofibrils.     

Polymerization of aniline on polyaniline membranes

When solutions of aniline hydrochloride and ammonium peroxydisulfate were separated by a semipermeable cellulose membrane, the reactants met at the membrane and produced a polyaniline (PANI) membrane at the interface. The oxidative polymerization of aniline then proceeded in situ on the PANI-cellulose composite membrane. PANI was produced entirely at the monomer side of the membrane; about 80% conversion of aniline to PANI was observed after 24 h. The oxidation of aniline with peroxydisulfate consists in the transfer of electrons from aniline to the oxidant; it is proposed that electrons pass through the PANI membrane, which is conducting, and electroneutrality is maintained by the simultaneous transfer of protons. The reaction between aniline and peroxydisulfate thus takes place without the need for both reactant molecules to be in physical contact. The residual aniline is located only at its original side of the membrane, but the product of ammonium peroxydisulfate conversion, ammonium hydrogen sulfate, was found on both sides of the membrane. Fourier-transform infrared spectroscopy has been used to analyze PANI, the reaction residues and byproducts, and to prove that PANI is protonated with counter-ions of the sulfate type. Using this technique, we have detected only small differences in the molecular structure of PANI prepared with the membrane-separated reactants and in the polymerization when reactants were mixed; also, the molecular weights differed only marginally. The conductivity of both types of PANI was about the same. The repeated polymerization of aniline on the earlier prepared PANI-cellulose membrane yielded similar results, thus confirming the proposed concept of coupled electron- and proton-transfer through the PANI membrane.     

Novel filled polymer composites prepared from in situ polymerization via a colloidal approach: II. Blends of kaolin/Nylon-6 in situ composites with conventional Nylon-6 and -66

A novel in situ composite comprised of kaolin clay fillers and polyamide 6 (Nylon-6) was synthesized via a colloidal approach by suspending kaolin particles in aqueous caprolactam and then polymerizing the caprolactam under elevated temperature and pressure. This in situ polymerization technique enables the deposition of nylon molecules directly onto the filler surface. It offers a much larger contact surface area for the nylon molecules to interact with the filler particles and enhances filler/matrix interaction through polymer miscibility. The kaolin particles were shown to be uniformly dispersed in Nylon-6 matrix without appreciable agglomeration. In the highly clay-loaded composites such as the 50/50 kaolin/Nylon-6 in situ composite, the deposited nylon molecules probably form a coated layer on the filler particles. This kind of nylon coated fillers may be applied as a reinforcing entity to commercial Nylon-6 or −;66 by improving particle dispersion and melt processability. The 50/50 kaolin/Nylon-6 in situ composites have been used as a masterbatch for blending with commercial Nylon-6 and Nylon-66 to take advantage of their good properties and to reduce cost. Rheology and mechanical properties of the masterbatch/nylon composites have been investigated in comparison with those of the conventional melt-mixed composites. The improvement of rheological and mechanical properties of the in situ composites has been discussed in relation to the composite structure. © 1996 John Wiley & Sons, Inc.     

Coating of zinc ferrite particles with a conducting polymer, polyaniline

Particles of zinc ferrite, ZnOFe2O3, were coated with polyaniline (PANI) phosphate during the in situ polymerization of aniline in an aqueous solution of phosphoric acid. The PANI-ferrite composites were characterized by FTIR spectroscopy. X-ray photoelectron spectroscopy was used to determine the degree of coating with a conducting polymer. Even a low content of PANI, 1.4 wt%, resulted in the 45% coating of the particles' surface. On the other hand, even at high PANI content, the coating of ferrite surface did not exceeded 90%. This is explained by the clustering of hydrophobic aniline oligomers at the hydrophilic ferrite surface and the consequent irregular PANI coating. The conductivity increased from 2 x 10(-9) to 6.5 S cm(-1) with increasing fraction of PANI phosphate in the composite. The percolation threshold was located at 3-4 vol% of the conducting component. In the absence of any acid, a conducting product, 1.4 x 10(-2) Scm(-1), was also obtained. As the concentration of phosphoric acid increased to 3 M, the conductivity of the composites reached 1.8 S cm(-1) at 10-14 wt% of PANI. The ferrite alone can act as an oxidant for aniline; a product having a conductivity 0.11 S cm(-1) was obtained after a one-month immersion of ferrite in an acidic solution of aniline.     

Preparation and characterization of polyaniline-containing Na-AlMCM-41 as composite material with semiconductor behavior

Composite material formed from a mesoporous aluminosilicate, Na-AlMCM-41, with conducting polyaniline (PANI) has been synthesized by an in situ polymerization technique. Studies of aniline adsorption over mesoporous Na-AlMCM-41 synthesized in our laboratory allowed us to find the modes in which aniline interacts with the active sites of Na-AlMCM-41. In order to obtain the best reaction conditions to polymerize aniline onto Na-AlMCM-41, aniline was first polymerized to produce pure PANI. Hence, the oxidative in situ polymerization was carried out by two procedures, differing in the polymerization time and in static or stirring conditions. Studies of infrared spectroscopy and UV-vis spectroscopy indicated that higher polymerization time and static conditions allowed us to obtain mainly polyaniline in emeraldine form on the host. The N(2) isotherm of the polyaniline/Na-AlMCM-41 composite (PANI/MCM) indicated that the shape was similar to that of MCM, but the shift to saturation transition to lower partial pressure shows that the channels are occupied by PANI and they are now narrowed. The thermal properties of PANI, Na-AlMCM-41, and composite were investigated by TGA analyses and we found that the polymer shows higher thermal stability when it is forming the composite. Scanning electron microscopy indicated that PANI is not on the outer surface of the host. Conductivity studies show that PANI/Na-AlMCM-41 exhibits semiconductor behavior at room temperature and its conductivity was 7.0 x 10(-5) S/cm, smaller than that of pure polyaniline. PANI/Na-AlMCM-41 conductivity shows an increase as temperature increases. Magnetic measurements at room temperature confirmed that the composite has paramagnetic behavior; at lower temperatures the composite became diamagnetic.     

The Electrochemical Properties of Nanocomposite Films Obtained by Chemical In Situ Polymerization of Aniline and Carbon Nanostructures

Interactions between the π bonds in the aromatic rings of polyaniline (PANI) with carbon nanostructures (CNs) facilitate charge transfer between the two components. Different types of phenyleneamine‐terminated CNs, including carbon nano‐onions (CNOs) and single‐walled and multi‐walled carbon nanotubes (SWNTs and MWNTs, respectively), were prepared as templates, and the CN/PANI nanocomposites were easily prepared with uniform core–shell structures. By varying the ratio of the aniline monomers relative to the CNs in the in situ chemical polymerization process, the thickness of the PANI layers was effectively controlled. The morphological and electrical properties of the nanocomposite were determined and compared. The thickness and structure of the PANI films on the CNs were characterized by transmission electron microscopy (TEM), scanning electron microscopy (SEM), and infrared spectroscopy. TEM and SEM revealed that the composite films consisted of nanoporous networks of CNs coated with polymeric aniline. The electrochemical properties of the composites were investigated by cyclic voltammetry and electrochemical impedance spectroscopy. These studies showed that the CN/PANI composite films had lower resistance than pure polymeric films of PANI, and the presence of CNs much improved the mechanical stability. The specific electrochemical capacitance of the CNO/PANI composite films was significantly larger than for pure PANI.     

乳液聚合中聚苯胺膜形成的动力学研究

以(NH4)2S2O8(APS)为氧化剂,十二烷基苯磺酸(DBSA)同时为乳化剂和掺杂剂,采用乳液聚合方法制备聚苯胺膜(PANIfilm),用石英晶体微天平(QCM)实时监测聚苯胺膜的形成过程,并对其动力学过程进行研究.结果表明,聚苯胺成膜反应对APS是0.5级,对苯胺是1级,聚苯胺膜增长速率随温度的升高而增加,而聚苯胺膜的最终沉积量却减小,表观活化能Ea=41.15kJ/mol,与均相溶液聚合成膜法的结果相近;随着DBSA浓度的增加,聚苯胺膜增长速率减小,而最终的沉积量增大.     

Fabrication, morphology and thermal degradation behaviors of conductive polyaniline coated monodispersed polystyrene particles

This study describes the preparation of polyaniline (PANI) coated on the surface of monodispersed 400 nm polystyrene (PS) particles by in situ chemical oxidative polymerization. The monodispersed 400 nm PS particles served as cores were synthesized using the emulsion polymerization. Both images observed by field-emission scanning electron microscopy and transmission electron microscopy show the presence of a thin PANI layer uniformly coated on the surface of PS particle. The electrical conductivity of various amounts of PANI-coated PS particles is significantly increased about 13 orders of magnitude compared to that of the pristine PS particles. Differential scanning calorimetry (DSC) and thermogravimetric analyzer (TGA) were used to investigate the thermal stability and thermal degradation behavior of PS and PANI-coated PS particles. Both DSC and TGA curves revealed that the coating of a thin PANI layer on the surface of PS can drastically increase the thermal stability of PS matrix. TGA isothermal degradation data illustrate that the activation energy of the PANI-coated PS particle is larger than that of PS. This phenomenon can be attributed to the incorporation of PANI coating on the surface of PS particle caused a decrease in the degradation rate and an increase in the residual weight for the PANI-coated PS particle.     

聚苯胺/碳化钨导电复合材料的合成

以苯胺和过硫酸胺为原料,采用原位聚合方法合成了聚苯胺/碳化钨(PANI/WC)导电复合材料。研究了反应体系中碳化钨的含量对复合材料电导率的影响,确定了较佳的聚合条件,并且通过FT-IR、XRD、XPS和DSC-TGA等手段对复合材料的结构和性能进行了表征和分析。结果表明:碳化钨(WC)的加入提高了聚苯胺的电子导电性能,复合材料中聚苯胺组分为无定型,WC的晶型在反应前后并未发生变化,复合材料的热稳定性好并且质子化程度更高。     

模板合成H_4PMo_(11)VO_(40)/聚苯胺纳米线列阵及其聚合机理探讨

在氧化铝模板中制备了HPA/PANI纳米线列阵,SEM、TEM表明列阵中纳米线直径约为80 nm;XRD与FT-IR证明形成了有效掺杂;单根纳米线的导电率为16.2 S.cm-1;材料的TG-DTA表明PANI纳米线材料有三步失重过程,失去吸附水过程,多酸失去结晶水和PANI结构持续分解过程,多酸结构分解过程;在氧化聚合过程中H4PMo11VO40即为质子酸又为氧化剂和掺杂剂;聚合反应采用自由基机理进行,掺杂反应发生在形成醌二亚胺式自由基正离子和双苯胺式自由基正离子和醌二亚胺式自由基正离子偶联聚合成链结构时.     

Synthesis and characterization of C60/polyaniline composites from interfacial polymerization

C₆₀/polyaniline (PANI) nanocomposites have been synthesized by the oxidative polymerization of aniline with ammonium peroxydisulfate in the presence of C₆₀ by using an interfacial reaction. When compared with the pure PANI nanofibers from the similar process, the diameter of the obtained C₆₀/PANI nanofibers was increased because of the encapsulation of C₆₀ into PANI during aniline polymerization, which resulted from the charge‐transfer interactions between C₆₀ and aniline fragment in PANI. In addition, the resulting C₆₀/PANI nanocomposites synthesized from the low initial C₆₀/aniline molar ratio (less than 1:25) showed the homogenous morphology composed of fiber network structures, which has an electrical conductivity as high as 1.1 × 10^?4 S/cm. However, the C₆₀/PANI nanocomposites from the higher initial C₆₀/aniline molar ratio (more than 1:15) showed the nonuniformly distributed morphology, and the electrical conductivity was decreased to 3.5 × 10^?5 S/cm. Moreover, the C₆₀/PANI nanocomposites from the interfacial reaction showed a higher value of electrical conductivity than the mechanically mixed C₆₀/PANI blends with the same C₆₀ content, because of the more evenly distributed microstructures. FTIR, UV–vis, and CV data confirmed the presence of C₆₀ and the significant charge‐transfer interactions in the resultant nanocomposites, which was responsible for the morphology development of the C₆₀/PANI and the variation of the electrical conductivity. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012