HyperMacs. Long Chain Branched Analogues of Hyperbranched Polymers Prepared by the Polycondensation of AB2 Macromonomers

We describe here a new strategy for the synthesis of polymers with highly branched architectures. The strategy involves the synthesis by anionic polymerization of well-defined AB₂ polystyrene macromonomers with molecular weights from 3,600 to 94,000 gmol⁻¹, which are then converted via a one-pot polycondensation reaction into high molecular weight, long-chain (hyper)branched architectures. Since the Hyperbranched structures are built up from condensation Macromonomers we have coined the term ‘HyperMac’ to describe these branched polymers. In this paper we report the synthesis of the HyperMacs, the optimal conditions for the polycondensation reaction and some preliminary characterization studies.     

Rheological properties of HyperMacs—long‐chain branched analogues of hyperbranched polymers

HyperMacs are long chain branched analogues of hyperbranched polymers, differing only in the sense that they have polymer chains, rather than monomers between branch points. Although the building blocks for HyperMacs and AB₂ macromonomers can be well defined in terms of molecular weight and polydispersity, the nature of the coupling strategy adopted for the synthesis of the HyperMacs results in branched polymers with a distribution of molecular weights and architectures. Melt rheology showed polystyrene HyperMacs to be thermorheologically simple, obeying William–Landel–Ferry behavior. Zero shear viscosities of the polymers were shown to increase with average molecular weight and the melts display shear‐thinning behavior. HyperMacs showed little evidence for relaxation by reptation and the rheological behavior agreed well with the Cayley tree model for hierarchical relaxation in tube models of branched polymers. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2762–2769, 2007     

Synthesis and characterization of hyperbranched polystyrene via click reaction of AB2 macromonomer

Well‐defined hyperbranched polystyrenes have been successfully prepared by polymerization of AB₂ macromonomer, polystyrene containing an azide group at its one end and two terminal propargyl groups at the other end via click reaction. For preparation of AB₂ macromonomers, an ATRP initiator, bispropargyl 2‐bromosuccinate (BPBS) with two propargyl groups and one bromine group was synthesized by the successive bromination and esterification reaction of L ‐aspartic acid. The resulting BPBS initiated the ATRP of St, and subsequently, the terminal bromine groups of (CH≡C)₂‐PS‐Brs were substituted by N₃ via the reaction with sodium azide resulting the AB₂ macromonomer, (CH≡C)₂‐PS‐N₃ with various molecular weights. All intermediates and the resultant polymers were characterized by GPC, ¹H NMR, FTIR, and MALLS methods. The polymerization kinetics study showed fast increase of DP at the initial stage of polymerization and then slow increase of their DP. The final “HyperMacs” have high‐molecular weight up to M_w,MALLS = 340,000 g/mol, their molecular weight distributions were moderately narrow (M_w/M_n = 1.47–1.65). The ratios of [η]_H/[η]_L of the HyperMacs formed in the polymerization system increased with evolution of polymerization. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 454–462, 2010     

Evidence for chain transfer in the atom transfer radical polymerization of butyl acrylate

Poly(butyl acrylate) (PBuA) of high molecular weight was synthesized by atom transfer radical polymerization (ATRP) in ethyl acetate. Whereas for low molecular weight polymers, a linear increase of the number‐average molecular weight, M_n, versus conversion and narrow molecular weight distributions indicate the suppression of side reactions, a downward curvature in the plot of M_n versus conversion was observed for high molecular weights (M_n > 50 000). This effect is explained by chain transfer reactions, leading to branched polymers. GPC measurements with a viscosity detector give evidence for the branched structure of high molecular weight polymers obtained in ATRP. In addition, transfer to solvent or monomer is likely to occur.     

Anionic polymerization of styrenic macromonomers of polyisoprene,polybutadiene, and polystyrene

Anionic polymerization and high‐vacuum techniques were used to prepare a series of well‐defined polyisoprene, polybutadiene, and polystyrene polymacromonomers. The procedure involved (1) the synthesis of styrenic macromonomers in benzene by the selective reaction of the corresponding macroanion with the chlorine of 4‐(chlorodimethylsilyl)styrene (CDMSS) and (2) the in situ anionic polymerization of the macromonomer without previous isolation. The synthesis of the macromonomers [polyisoprene macromonomer: 11 samples, weight‐average molecular weight (M_w) = 1000–18,000; polybutadiene macromonomer: 5 samples, M_w = 2000–4000; and polystyrene macromonomer: 2 samples, M_w = 1300 and 3600] was monitored by size exclusion chromatography with refractive index/ultraviolet detectors. Selectivity studies with CDMSS indicated that polybutadienyllithum had the highest selectivity, and polystryryllithium the lowest. From kinetic studies it was concluded that the polymerization half‐life times were longer but comparable to those of styrene, and they appeared to only slightly depend on the molecular weight of the macromonomer chain (at least for low degrees of polymerization of the polymacromonomer and for M_w < 7000 for the macromonomer side chain). Dependence on the polymerization degree of the polymacromonomer product was also observed. All the prepared polymacromonomers were characterized by size exclusion chromatography with refractive index, ultraviolet and two‐angle laser light scattering detectors, and NMR spectroscopy. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 1038–1048, 2005     

Synthesis of branched polymers by means of anionic polymerization. 11. anionic synthesis of densely branched polystyrenes carrying double branches in each repeating unit

We have demonstrated the first successful synthesis of well-defined densely branched polystyrenes carrying double branches in each of all repeating unit of backbone polymer by the coupling reaction of 1,1-diphenylethylene-end-capped polystyryllithiums with novel polystyrene derivatives having two benzyl bromide moieties in each monomer unit. The coupling reaction efficiently and quantitatively proceeded without any steric limitations to introduce two polystyrene branches in each repeating unit under certain conditions in THF at −40°C. Thus, a series of 36.4- and 181-arm densely branched polystyrenes were synthesized (M_w = 365 ∼ 2 000 kg/mol, M_w/M_n = 1.01 ∼ 1.03). In the 36.4-arm branched polystyrenes thus synthesized, the maximum M_w value of the introduced polystyrene as a branch segment was 55.1 kg/mol. The experimental g‘ values of the 36.4-arm branched polystyrenes deterimined in the range of 0.14 ∼ 0.15 were very close to the value of 0.13 calculated from the empirical equation previously reported by Roovers.     

Synthesis of arborescent styrene homopolymers and copolymers from epoxidized substrates

The synthesis of arborescent styrenic homopolymers and copolymers was achieved by anionic polymerization and grafting. Styrene and p‐(3‐butenyl)styrene were first copolymerized using sec‐butyllithium in toluene, to generate a linear copolymer with a weight‐average molecular weight M_w = 4000 and M_w/M_n = 1.05. The pendant double bonds of the copolymer were then epoxidized with m‐chloroperbenzoic acid. A comb‐branched (or arborescent generation G0) copolymer was obtained by coupling the epoxidized substrate with living styrene‐p‐(3‐butenyl)styrene copolymer chains with M_w ≈ 5000 in a toluene/tetrahydrofuran mixture. Further cycles of epoxidation and coupling reactions while maintaining M_w ≈ 5000 for the side chains yielded arborescent copolymers of generations G1–G3. A series of arborescent styrene homopolymers was also obtained by grafting M_w ≈ 5000 polystyrene side chains onto the linear and G0–G2 copolymer substrates. Size exclusion chromatography measurements showed that the graft polymers have low polydispersity indices (M_w/M_n = 1.02–1.15) and molecular weights increasing geometrically over successive generations. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Large‐scale synthesis of arborescent polystyrenes

A method was developed for the large (100 g) scale synthesis of arborescent polystyrenes using acetyl coupling sites. Successive generations of dendritic graft polymers were obtained from cycles of polystyrene substrate acetylation with acetyl chloride and coupling in the presence of LiCl with “living” polystyryllithium chains capped with 2‐vinylpyridine units. The grafting yield for the synthesis of a generation zero (G0 or comb‐branched) arborescent polystyrene under the conditions previously reported for the 10 g scale reactions decreased from 95 to 75% when scaled up to 100 g. The lowered yield was linked to side chain dimerization and deactivation of the macroanions. The modified 100 g scale procedure, using end‐capping of the polystyryllithium with 1,1‐diphenylethylene and the addition of 3–6 equivalents per living end of 2‐vinylpyridine as a dilute solution, eliminated side chain dimerization and provided grafting yields of up to 95%. The large‐scale procedure developed was applied to the synthesis of arborescent polystyrenes of generations up to G2 with low polydispersity indices (M_w/M_n ≤ 1.04) and molecular weights increasing in an approximately geometric fashion for each cycle. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 5742–5751, 2008     

Arborescent polypeptides from γ‐benzyl l‐glutamic acid

The synthesis of arborescent polymers with poly(γ‐benzyl L‐glutamate) (PBG) side chains was achieved through successive grafting reactions. The linear PBG building blocks were produced by the ring‐opening polymerization of γ‐benzyl L‐glutamic acid N‐carboxyanhydride initiated with n‐hexylamine. The polymerization conditions were optimized to minimize the loss of amino chain termini in the reaction. Acidolysis of a fraction of the benzyl groups on a linear PBG substrate and coupling with linear PBG using a carbodiimide/hydroxybenzotriazole promoter system yielded a comb‐branched or generation zero (G0) arborescent PBG. Further partial deprotection and grafting cycles led to arborescent PBG of generations G1 to G3. The solvent used in the coupling reaction had a dramatic influence on the yield of graft polymers of generations G1 and above, dimethylsulfoxide being preferable to N,N‐dimethylformamide. This grafting onto scheme yielded well‐defined (M_w/M_n ≤ 1.06), high molecular weight arborescent PBG in a few reaction cycles, with number‐average molecular weights and branching functionalities reaching over 10⁶ and 290, respectively, for the G3 polymer. α‐Helix to coiled conformation transitions were observed from N,N‐dimethylformamide to dimethyl sulfoxide solutions, even for the highly branched polymers. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 5270–5279     

Polystyrene with dendritic branching by convergent living anionic polymerization. II. Approach using vinylbenzyl chloride

Vinylbenzyl chloride (VBC) has been used as a coupling agent in Convergent Living Anionic Polymerization to produce polymers with dendritic branching. The slow addition of a stoichiometric amount of VBC to living polystyrene chains allows the coupling to proceed through macromonomer formation followed by vinyl addition. Changing the reaction conditions produced two types of structures. Star‐shaped polymers with a hyperbranched core were made by the continuous slow addition of VBC alone, and chain‐extended hyperbranched structures with varied molecular weight between branch points were produced by the slow addition of VBC mixed with different amounts of styrene monomer. The extent of growth of the two different types of structures ranged from 2.4 to 2.6 generations for the case of VBC added alone, corresponding to an average of 5.3 to 6.1 arms attached to the hyperbranched core, and from 3.2 to 4.2 generations for polymers produced from the addition of VBC mixed with styrene. Relatively low polydispersities were obtained for all samples. The highly branched nature of the polymers was reflected in the low intrinsic viscosity relative to linear polystyrene and in the dependence of glass‐transition temperature on the molecular weight relative to the number of end groups. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 4289–4298, 2000     

How good is CuAAC “click” chemistry for polymer coupling reactions?

¹H NMR and SEC analyses are used to investigate the overall efficiency of Copper Catalyzed Azide Alkyne Cycloaddition (CuAAC) “click” coupling reactions between alkyne‐ and azide‐terminated polymers using polystyrene as a model. Quantitative convolution modeling of the entire molecular weight distribution is applied to characterize the outcomes of the functional polymer synthesis reactions (i.e., by atom transfer radical polymerization), as well as the CuAAC coupling reaction. Incomplete functionality of the azide‐terminated polystyrene (∼92%) proves to be the largest factor compromising the efficacy of the CuAAC coupling reaction and is attributed primarily to the loss of terminal bromide functionality during its synthesis. The efficiency of the S_N2 reaction converting bromide to azide was found to be about 99%. After taking into account the influence of non‐functional polymer, we find that, under the reaction conditions used, the efficiency of the CuAAC coupling reaction determined from both techniques is about 94%. These inefficiencies compromise the fidelity and potential utility of CuAAC coupling reactions for the synthesis of hierarchically structured polymers. While CuAAC efficiency is expected to depend on the specific reaction conditions used, the framework described for determining reaction efficiency does provide a means for ultimately optimizing the reaction conditions for CuAAC coupling reactions. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 75–84     

Cryogenic degradation of polystyrene in solution

An ultra-high molecular weight and narrow distribution polystyrene ($\text{M}{}_{\mathrm{<mtext>w</mtext>}}\text{= 7.3 × 10}{}^6$, M_w/M_n = 1.13) was dissolved in a wide range of solvents. Potential degradation by freezing was studied as a function of solvent type, concentration, cooling rate and number of freezing cycles. Cryogenic experiments were conducted in dioxane, tetrahydrofuran, benzene, dichloroethane, cyclohexanone, p-xylene, methyl methacrylate and styrene. The extent of degradation did not relate to a single solvent parameter, but there seemed to be a tendency towards a limited degradation in solvents with low melting points and/or solubility parameters greatly different from that of polystyrene. A low polymer concentration as well as a high cooling rate promoted chain scission, the latter parameter being the most important. In cyclohexanone and p-xylene, linear relationships were observed between the number of scission per molecule and the number of freezing cycles at high polymer concentrations and at high cooling rates. At lower concentrations and slower cooling, the relationships were non-linear suggesting a different degradation mechanism. The most extensive change in molecular weight distribution was observed on freezing in styrene. After 45 freezing cycles, an $\text{M}$_w of only 2.3 × 10⁶ was observed. The results indicate that chain scission occurred together with polymerization and combination reactions. Freezing of suitable solutions of ultra-high molecular weight polymers can thus be used as a new way of initiating polymerizations by cooling rather than heating.     

Synthesis of star‐shaped polystyrenes via nitroxide‐mediated stable free‐radical polymerization

High molecular weight star‐shaped polystyrenes were prepared via the coupling of 2,2,6,6‐tetramethyl‐1‐piperidinyloxy (TEMPO) terminated polystyrene oligomers with divinylbenzene (DVB) in m‐xylene at 138 °C. The optimum ratio of the coupling solvent (m‐xylene) to divinylbenzene was determined to be 9 to 1 based on volume. Linear polystyrene oligomers (M_n = 19,300 g/mol, M_w/M_n = 1.10) were prepared in bulk styrene using benzoyl peroxide in the presence of TEMPO at approximately 130 °C under an inert atmosphere. Coupling of the TEMPO‐terminated oligomers under optimum conditions resulted in a product with a number average molecular weight exceeding 300,000 g/mol (M_w/M_n = 3.03) after 24 h, suggesting the formation of relatively well‐defined star‐shaped polymers. Additionally, the intrinsic viscosities of the star‐shaped products were lower than calculated values for linear analogs of equivalent molecular weight, which further supported the formation of a star‐shaped architecture. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 216–223, 2001     

A styryl tipno‐based nitroxide as efficient mediator for the synthesis of multiblock polystyrenes and well‐grafted polymers

The chloromagnesium exchange of 4‐chlorostyrene provides an easy access to a new versatile polymerizable 2,2,5‐trimethyl‐4‐phenyl‐3‐azahexane‐3‐nitroxide (TIPNO)‐based nitroxide. Indeed, first, its alkoxyamine based on the α‐methyl benzyl radical fragment efficiently mediates the polymerization of styrene (respectively n‐butyl acrylate) to yield branched polystyrene [respectively poly(n‐butyl acrylate)] with alkoxyamine function as branch point and well‐defined branches. Second, the self‐condensing of this polymerizable nitroxide by manganese coupling affords a mixture of oligomeric linear polyalkoxyamines. Polymerization of styrene mediated with these polyalkoxyamines gives multiblock polystyrenes with alkoxyamine group as linker between polystyrene blocks and exhibits the following features: the synthesis of the polystyrene blocks is controlled as their average molecular weight M_n(block) increases linearly with conversion and their average dispersity M_w/M_n(block) decreases with it. At a given temperature, the molecular weight and the dispersity of the polyalkoxyamines weakly impact M_n(block) and M_w/M_n(block). In contrast, the molecular weight of the multiblock polystyrene increases linearly with conversion until reaching a constant value. The number of block is independent of the molecular weight of the polyalkoxyamines. These unusual results can be explained by the fact that during polymerization, mediating TIPNO‐based polymeric nitroxides with different lengths are generated and are exchanged. Finally the dispersity of the multiblock polystyrene is quite broad and lies between 1.7 and 2.8. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Synthesis of well‐defined cyclodextrin‐core star polymers

The synthesis of 21‐arm methyl methacrylate (MMA) and styrene star polymers is reported. The copper (I)‐mediated living radical polymerization of MMA was carried out with a cyclodextrin‐core‐based initiator with 21 independent discrete initiation sites: heptakis[2,3,6‐tri‐O‐(2‐bromo‐2‐methylpropionyl]‐β‐cyclodextrin. Living polymerization occurred, providing well‐defined 21‐arm star polymers with predicted molecular weights calculated from the initiator concentration and the consumed monomer as well as low polydispersities [e.g., poly(methyl methacrylate) (PMMA), number‐average molecular weight (M_n) = 55,700, polydispersity index (PDI) = 1.07; M_n = 118,000, PDI = 1.06; polystyrene, M_n = 37,100, PDI = 1.15]. Functional methacrylate monomers containing poly(ethylene glycol), a glucose residue, and a tert‐amine group in the side chain were also polymerized in a similar fashion, leading to hydrophilic star polymers, again with good control over the molecular weight and polydispersity (M_n = 15,000, PDI = 1.03; M_n = 36,500, PDI = 1.14; and M_n = 139,000, PDI = 1.09, respectively). When styrene was used as the monomer, it was difficult to obtain well‐defined polystyrene stars at high molecular weights. This was due to the increased occurrence of side reactions such as star–star coupling and thermal (spontaneous) polymerization; however, low‐polydispersity polymers were achieved at relatively low conversions. Furthermore, a star block copolymer consisting of PMMA and poly(butyl methacrylate) was successfully synthesized with a star PMMA as a macroinitiator (M_n = 104,000, PDI = 1.05). © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2206–2214, 2001     

Effects of radiation and chain ends on fatigue behaviour of polystyrene

Fatigue lifetimes, under a given alternating stress amplitude, have been determined for a series of linear and branched polystyrenes. The branched polymers were obtained by a crosslinking reaction using γ-irradiation from a Co⁶⁰ source. By control of irradiation time, a series of branched samples of progressively increasing weight average molecular weight ($\text{M}$_w), with little change in number average molecular weight ($\text{M}$_n, were obtained. From comparison of fatigue data for these irradiated and branched samples with fatigue data obtained on a series of linear polystyrenes of increasing molecular weight, it may by concluded that appreciable increases in fatigue endurance can be achieved by increase in $\text{M}$_n and reduction in chain end density. For the irradiated samples, whether irradiated in air or in vacuum, fatigue lifetimes were comparable to or less than lifetimes to fracture for the unirradiated polymer, even though significant increases in $\text{M}$_w had occurred. It is suggested that the improved fatigue performance with increase of $\text{M}$_n is a consequence of increased craze stability resulting from the greater degree of chain entanglement and the smaller proportion of chain end defects.     

Synthesis of well‐defined polymers end‐functionalized with crosslinkable aziridine groups by living anionic polymerization

Well‐defined end‐functionalized polystyrene, poly(α‐methylstyrene), and polyisoprene with polymerizable aziridine groups were synthesized by the termination reactions of the anionic living polymers of styrene, α‐methylstyrene, and isoprene with 1‐[2‐(4‐chlorobutoxy)ethyl]aziridine in tetrahydrofuran at ?78 °C. The resulting polymers possessed the predicted molecular weights and narrow molecular weight distributions (weight‐average molecular weight/number‐average molecular weight < 1.1) as well as aziridine terminal moieties. The cationic ring‐opening polymerization of the ω‐monofunctionalized polystyrene having an aziridinyl group with Et₃OBF₄ gave the polymacromonomer, whereas the α,ω‐difunctional polystyrene underwent crosslinking reactions to afford an insoluble gel. Crosslinking products were similarly obtained by the reaction of the α,ω‐diaziridinyl polystyrene with poly(acrylic acid)‐co‐poly(butyl acrylate). © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 4126–4135, 2005     

Theoretical study of chain transfer in anionic polymerization. Transfer by the mechanism of side-group substitution

A new theoretical consideration of chain transfer to monomer in the anionic polymerization of hydrocarbon monomers is presented. It is shown that the kinetic scheme used in theoretical studies reported previously contradicts the widespread views on the chemical mechanism of carbanionic reactions. It is suggested that the most probable path of the transfer reaction is the proton abstraction from the side group of the monomer; the terminal double bond of the monomer molecule remains unchanged, and therefore the intermediate species can participate in succeeding reactions as a macromonomer. The molecular characteristics of polymer formed in processes with monomer transfer by side-group substitution are determined. At high conversion, the polymer formed in such a process is shown to possess a number-average degree of polymerization, P̄_n, approaching the theoretical value for living polymers, and a P̄_w exceeding it the more the higher the intensity of transfer. Furthermore, it shows a broad molecular weight distribution and a fairly noticeable degree of branching. These results considerably differ from those previously reported.     

Generalized Universal Molecular Weight Calibration Parameter in GPC

Abstract

In this report we show by experimental and theoretical investigations that the commonly used GPC universal calibration parameter, the intrinsic viscosity multiplied by the weight average molecular weight ([η] M^w) is incorrect. The error which can arise by using [η] M to calculate the molecular weight across the GPC chromatogram for nonuniformly branched polymers [poly(vinyl acetate) and low density polyethylene] and copolymers with compositional drift, could be very large. We also show conclusively that the number average molecular weight M_n is the correct average to use for the universal calibration parameter. We therefore recommend that our general universal Calibration parameter [η] M_n be used for calculating the molecular weight across the chromatogram for all polymer systems (linear and branched homopolymers, copolymers with or without compositional drift and for polymer blends).     

Crystallizable Polyphenylacetylene-Preparation and Solution Properties

The molecular weight distribution (MWD) of crystallizable polyphenylacetylene prepared near room temperature in the presence of ferric acetylacetonate and triethylaluminum was determined through use of fractions characterized by vapor pressure osmometry and gel permeation chromatography (GPC). The number- and weight-average molecular weights (M _n and M _w) are both less than the molecular weight corresponding to the maximum of the weight distribution function, which lacks a high molecular weight tail. M _wandM _n is less than is consistent with models allowing for chain termination characteristic of vinyl polymers. GPC elution volumes are much less than those characteristic of polystyrene of similar molecular weight, and the Mark-Houwink exponent is high (2.4 for M _v 4800 to 6800). These data indicate more rodlike behavior than for polystyrene of equivalent molecular weight. The MWD and other data suggest intramolecular chain termination, possibly associated with the molecule's tendency to form paramagnetic defect states.