Surface-initiated atom-transfer radical polymerization (ATRP) of poly(ethylene glycol) monomethacrylate (PEGMA) was carried out on the hydrogen-terminated Si(100) substrates with surface-tethered alpha-bromoester initiator. Kinetic studies confirmed an approximately linear increase in polymer film thickness with reaction time, indicating that chain growth from the surface was a controlled "living" process. The "living" character of the surface-grafted PEGMA chains was further ascertained by the subsequent extension of these graft chains, and thus the graft layer. Well-defined polymer brushes of near 100 nm in thickness were grafted on the Si(100) surface in 8 h under ambient temperature in an aqueous medium. The hydroxyl end groups of the poly(ethylene glycol) (PEG) side chains of the grafted PEGMA polymer were derivatized into various functional groups, including chloride, amine, aldehyde, and carboxylic acid groups. The surface-functionalized silicon substrates were characterized by reflectance FT-IR spectroscopy and X-ray photoelectron spectroscopy (XPS). Covalent attachment and derivatization of the well-defined PEGMA polymer brushes can broaden considerably the functionality of single-crystal silicon surfaces. 相似文献
Surface-initiated atom transfer radical polymerization (ATRP) was used to graft hydrophilic comb-like poly((poly(ethylene glycol) methyl ether methacrylate), or P(PEGMA), brushes from chloromethylated poly(phthalazinone ether sulfone ketone) (CMPPESK) membrane surfaces. Prior to ATRP, chloromethylation of PPESK was beforehand performed and the obtained CMPPESK was prepared into porous membranes by phase inversion process. It was demonstrated that the benzyl chloride groups on the CMPPESK membrane surface afforded effective macroinitiators to graft the well-defined polymer brushes. Attenuated total reflectance Fourier transform infrared (ATR-FTIR) spectroscopy and X-ray photoelectron spectroscopy (XPS) confirmed the grafting of P(PEGMA) chains. Water contact angle measurements indicated that the introduction of P(PEGMA) graft chains promoted remarkably the surface hydrophilicity of PPESK membranes. The effects of P(PEGMA) immobilization on membrane morphology, permeability and fouling resistance were investigated. It was found that the comb-like P(PEGMA) grafts brought smaller pore diameters and higher solute rejections to PPESK membranes. The results of dynamic anti-fouling experiments showed the anti-fouling ability of the membranes was significantly improved after the grafting of P(PEGMA) brushes. 相似文献
Novel, unique amphiphilic pentablock terpolymers consisting of the highly hydrophobic polyisobutylene (PIB) mid-segment attached to the hydrophilic combshaped poly(poly(ethylene glycol) methacrylate) (PPEGMA) polymacromonomer chains, which are coupled to poly(methyl methacrylate) (PMMA) outer segments were synthesized by the combination of quasiliving carbocationic polymerization and atom transfer radical polymerization (ATRP). First, a bifunctional PIB macroinitiator was prepared by quasiliving carbocationic polymerization and subsequent quantitative chain end derivatizations. Quasiliving ATRP of PEGMAs with different molecular weights (Mn = 188, 300 and 475 g/mol) led to triblock copolymers which were further reacted with MMA under ATRP conditions to obtain PMMA-PPEGMA-PIB-PPEGMA-PMMA ABCBA-type pentablock copolymers. It was found that slow initiation takes place between the PIB macroinitiator and PEGMA macromonomers with higher molecular weights via ATRP. ATRP of MMA with the resulting block copolymers composed of PIB and PPEGMA chain segments led to the desired block copolymers with high initiating efficiency. Investigations of the resulting pentablock copolymers by DSC, SAXS and phase mode AFM revealed that nanophase separation occurs in these new macromolecular structures with average domain distances of 11-14 nm, and local lamellar self-assembly takes place in the pentablocks with PPEGMA polymacromonomer segments of PEGMAs with Mn of 118 g/mol and 300 g/mol, while disordered nanophases are observed in the block copolymer with PEGMA having molecular weight of 475 g/mol. These new amphiphilic block copolymers composed of biocompatible chain segments can find applications in a variety of advanced fields. 相似文献
Hydrophilic surface modification of poly(phthalazinone ether sulfone ketone)(PPESK) porous membranes was achieved via surface-initiated atom transfer radical polymerization(ATRP) in aqueous medium.Prior to ATRP.chloromethyl groups were introduced onto PPESK main chains by chloromethylation.Chloromethvlated PPESK(CMPPESK) was fabricated into porous membrane through phase inversion technique.Hydrophilic poly(poly(ethylene glycol) methyl ether methacrylate)(P(PEGMA)) brushes were grafted from CMPPESK membra... 相似文献
Surface-grafted block copolymer brushes with continuous composition gradients containing poly(poly(ethylene glycol) monomethacrylate) (P(PEGMA)) and poly(N-isopropylacrylamide) (PNIPAAm) chains were fabricated by integration of the surface-initiated atom transfer radical polymerization (SI-ATRP) and continuous injection method.Three types of copolymer gradients were prepared: (1) a uniform P(PEGMA) layer was block copolymerized with a gradient PNIPAAm layer (PP1);(2) a gradient P(PEGMA) layer was block copo... 相似文献
This contribution presents a new strategy to grow nonfouling poly (poly(ethylene glycol)methacrylate) (PPEGMA) brushes from polydimethylsiloxane (PDMS) substrates. The strategy presented here is based on the use of a sequence of vapor deposition/hydrolysis cycles to generate a surface-confined atom transfer radical polymerization (ATRP)-initiator functionalized interpenetrating polymer network (IPN) layer. In contrast to most other approaches that have been developed to graft thin polymer layers from PDMS substrates, this technique obviates the need for UV/ozone pretreatment of the PDMS substrate. It is shown that the surface-confined ATRP-initiator functionalized IPN layer can be used to grow PPEGMA brushes in a controlled fashion and that the resulting PPEGMA coating significantly reduces nonspecific protein adsorption as compared to unmodified PDMS substrates. 相似文献
Preparation of an amphiphilic graft copolymer having poly(phthalazinone ether sulfone ketone)(PPESK) as main chains was carried out by atom transfer radical polymerization(ATRP).The precursor,chloromethylated PPESK (CMPPESK),was prepared by using chioromethylether as chloromethylation agent.Then,poly(ethylene glycol) methyl ether methacrylate(PEGMA) was used as monomer to synthesize PPESK-g-P(PEGMA) by ATRP method under the catalysis of a cuprous chloride/2,2'-bipyridyl system.PPESK/PPESK-g-P(PEGMA) blen... 相似文献
Argon plasma-induced graft polymerization of a solution-coated macromonomer, poly(ethylene glycol) methyl ether methacrylate (PEGMA), on the Si(100) surface was carried out to impart anti-fouling properties to the Si(100) surface. The surface composition and microstructure of the PEGMA graft-polymerized Si(100) surfaces were characterized by X-ray photoelectron spectroscopy (XPS), Fourier-transform infrared spectroscopy (FTIR), and atomic force microscopy (AFM) measurements. The extent of crosslinking in the plasma-graft polymerized PEGMA (pp-PEGMA) was estimated by gel fraction determination. In general, an appropriate RF power of about 15 W and a PEGMA macromonomer concentration of about 1 wt% in the coating solution for plasma polymerization produced a high graft yield of pp-PEGMA on the Si(100) surface (the pp-PEGMA-g-Si surface). The Si(100) surface with a high concentration of the grafted pp-PEGMA was effective in preventing bovine serum albumin (BSA) adsorption and platelet adhesion. 相似文献
Poly(L ‐lactic acid)‐block‐poly(poly(ethylene glycol) monomethacrylate) (PLLA‐b‐PPEGMA) has been prepared by the ring‐opening polymerization of lactide with a double‐headed initiator, 2‐hydroxyethyl 2′‐methyl‐2′‐bromopropionate (HMBP), followed by atom transfer radical polymerization (ATRP) of poly(ethylene glycol) monomethacrylate (PEGMA). PLLA‐b‐PPEGMA nanoparticles with encapsulated Fe3O4 are prepared by a solvent evaporation/extraction technique, and then further functionalized with folic acid, a cancer targeting ligand. Our results show that such functionalized PLLA‐b‐PPEGMA nanoparticles have good potential as carriers for targeted drug delivery in cancer treatment.
Poly(PEGMA) homopolymer brushes were developed by atom transfer radical polymerization (ATRP) on the initiator-modified silicon surface (Si-initiator). Through covalent binding, protein immobilization on the poly(PEGMA) films was enabled by further NHS-ester functionalization of the poly(PEGMA) chain ends. The formation of polymer brushes was confirmed by assessing the surface composition (XPS) and morphology (atomic force microscopy (AFM), scanning electronic microscopy (SEM)) of the modified silicon wafer. The binding performance of the NHS-ester functionalized surfaces with two proteins horseradish peroxidase (HRP) and chicken immunoglobulin (IgG) was monitored by direct observation. These results suggest that this method which incorporates the properties of polymer brush onto the binding surfaces may be a good strategy suitable for covalent protein immobilization. 相似文献
A simple one-step method for the chloromethylation of polyimide (PI) under mild conditions was used to introduce benzyl chloride groups into PI film surface. Covalently tethered hydrophilic polymer brushes of poly(ethylene glycol) monomethacrylate (PEGMA) and glycidyl methacrylate (GMA) were prepared via surface initiated atom-transfer radical polymerization (ATRP) from the chloromethylated PI surfaces using benzyl chloride groups as the active ATRP initiators. A kinetics study indicated that the chain growth from the films was in agreement with a controlled process. The dormant chain ends of the grafted polymer on the PI films could reinitiate the consecutive surface-initiated ATRP to prepare surface-functionalized diblock copolymer brushes on the PI films. The modified surface was characterized by X-ray photoelectron spectroscopy (XPS) after each modification stage. Protein adsorption experiments indicated that the PI-P(PEGMA) membrane exhibited substantially improved anti-fouling properties compared to the pristine PI surface. 相似文献
In this study, a surface grafting of nonfouling poly(ethylene glycol) methyl ether acrylate (PEGMA) on poly(ethylene terephthalate) (PET) was carried out via surface-initiated atom-transfer radical polymerization (SI-ATRP) to improve hemocompatibility of polymer based biomaterials. To do this, the coupling agent with hydroxyl groups for the ATRP initiator was first anchored on the surface of PET films using photochemical method, and then these hydroxyl groups were esterified by bromoisobutyryl bromide, from which PET with various main chain lengths of PEGMA was prepared. The structures and properties of modified PET surfaces were investigated using water contact angle (WAC), ATR-FTIR, X-ray photoelectron spectroscopy (XPS) and Atomic force microscopy (AFM). The molecular weights of the free polymer from solution were determined by gel permeation chromatography (GPC). These results indicated that grafting of PEGMA on PET film is a simple way to change its surface properties. The protein adsorption resistance on the surfaces of PET was primarily evaluated by an enzyme-linked immunosorbent assay (ELISA). The result demonstrated that the protein adsorption could be well suppressed by poly(PEGMA) brush structure on the surface of PET. This work provides a new approach for polymers to enhance their biocompatibility. 相似文献
The ability to manipulate and control the surface properties of nylons is of crucial importance to their widespread applications. In this work, surface-initiated atom-transfer radical polymerization (ATRP) is employed to tailor the functionality of the nylon membrane and pore surfaces in a well-controlled manner. A simple two-step method, involving the activation of surface amide groups with formaldehyde and the reaction of the resulting N-methylol polyamide with 2-bromoisobutyryl bromide, was first developed for the covalent immobilization of ATRP initiators on the nylon membrane and its pore surfaces. Functional polymer brushes of 2-hydroxyethyl methacrylate (HEMA) and poly(ethylene glycol)monomethacrylate (PEGMA) were prepared via surface-initiated ATRP from the nylon membranes. A kinetics study revealed that the chain growth from the membranes was consistent with a "controlled" process. The dormant chain ends of the grafted HEMA polymer (P(HEMA)) and PEGMA polymer (P(PEGMA)) on the nylon membranes could be reactivated for the consecutive surface-initiated ATRP to produce the corresponding nylon membranes functionalized by P(HEMA)-b-P(PEGMA) and P(PEGMA)-b-P(HEMA) diblock copolymer brushes. In addition, membranes with grafted P(HEMA) and P(PEGMA) brushes exhibited good resistance to protein adsorption and fouling under continuous-flow conditions. 相似文献