Effect of filler networking on the response of thermosensitive composite hydrogels

Several composite hydrogels of poly(N-isopropylacrylamide) (pNIPAAm) with sodium montmorillonite (NaMM) have been synthesized using a fixed polymer/NaMM ratio (4:1 wt./wt.), but various monomer concentrations, in order to obtain hydrogels with different degrees of swelling, and thus different clay contents in the swollen state. For comparison, unfilled pNIPAAm gels have been also prepared at the same concentrations. The equilibrium swelling behaviour of the gels has been studied both in the swollen and in the shrunk state. In the swollen state, the polymer volume fraction increases with the initial monomer concentration C₀. In the shrunk state, the polymer fraction in pNIPAAm hydrogels is dependent on the specimen size and on C₀, whereas in the composite gels a constant polymer content is observed. When subjected to stepwise heating from 25 to 45 °C, unfilled gels undergo only poor deswelling. By contrast, complete deswelling takes place in composite gels. The latter show half-shrinking times varying over two orders of magnitude, depending on the monomer concentration and on the procedure followed to disperse NaMM, which determine the overall dispersion state of the filler, as evidenced by transmission electron microscopy (TEM). In particular, TEM observations show clay networking above a percolation threshold near 2.5 wt.% of NaMM. The effect of the incorporation of clay on the response to thermal stimuli is discussed in terms of the ability of NaMM to hinder the hydrophobic association of pNIPAAm segments and in terms of its dispersion state. It is suggested that, above the percolation threshold, NaMM forms a hydrophilic, physical network, through which water can flow also above the volume transition temperature, where pNIPAAm acquires a hydrophobic character.     

A comparative study of surfactant adsorption on model surfaces using the quartz crystal microbalance and the ellipsometer

The nature of hexaethylene glycol mono-n-tetradecyl ether (C(14)EO(6)) layers adsorbed onto different model surfaces was systematically investigated by means of QCM-D (quartz crystal microbalance-dissipation) and ellipsometry. The amount of non-ionic surfactant adsorbed is determined both at hydrophilic and hydrophobic surfaces. In particular, the substrates employed were hydrophilic silica, hydrophobized silica (using dimethyldichlorosilane), and hydrophobized gold surfaces (using 10-thiodecane and 16-thiohexadecane). It was shown that the frequency shift obtained from the QCM-D experiments results in an overestimation of the adsorbed mass. This is attributed to two different effects, viz. water that is coupled to the adsorbed layer due to hydration of the polar region of the surfactant and second water that for other reasons is trapped within the adsorbed layer. Furthermore, from the ellipsometry data the adsorbed layer thickness is determined. By combining the thickness information and the dissipation parameter (obtained from the QCM-D experiments), we note that the dissipation parameter is insufficient in describing the viscoelastic character of thin surfactant films.     

Effect of adsorbed layer surface roughness on the QCM-D response: focus on trapped water

The effect of surface roughness on the quartz crystal microbalance with dissipation monitoring (QCM-D) response was investigated with emphasis on determining the amount of trapped water. Surfaces with different nanoroughnesses were prepared on silica by self-assembly of cationic surfactants with different packing parameters. We used surfactants with quaternary ammonium bromide headgroups: the double-chained didodecyltrimethylammonium bromide (C12)2DAB (DDAB), the single-chained hexadecyltrimethylammonium bromide C16TAB (CTAB), and dodecyltrimethyl-ammonium bromide C12TAB (DTAB). The amount of trapped water was obtained from the difference between the mass sensed by QCM-D and the adsorbed amount detected by optical reflectometry. The amount of water, which is sensed by QCM-D, was found to increase with the nanoroughness of the adsorbed layer. The water sensed by QCM-D cannot be assigned primarily to hydration water, because it differs substantially for adsorbed surfactant layers with similar headgroups but with different nanoscale topographies.     

Bacterial polyesters grafted with poly(ethylene glycol): Behaviour in aqueous media

An easy method for grafting of poly(3-hydroxyoctanoate-co-3-hydroxyundecenoate) (PHOU) was developed. Oxidation of the pendant double bonds of PHOU into carboxyl groups to yield poly(3-hydroxyoctanoate-co-3-hydroxy-9-carboxydecanoate) (PHOD) and the esterification of the carboxyl side groups with poly(ethylene glycol) (PEG) were carried out in a single reaction solution. The grafting yield is dependent on the molar mass of the PEG graft. The maximum carboxyl group conversion (52%) was obtained with PEG M_n = 350 and decreased with increasing molar mass of PEG (19% for PEG M_n = 2000). Yields were determined by ¹H and ¹³C NMR. Short PEG grafts lowered the glass transition temperature (PHOD-g-PEG 350 −57 °C) compared to PHOD (−19 °C) and PHOU (−39 °C). This effect depends on the COOH conversion and PEG chain length. Grafting enhanced the hydrophilic character of the modified polymers making them soluble in polar solvents, such as alcohols and water/acetone mixtures. PHOD-g-PEG films were more stable towards hydrolytic degradation as PHOD films. No obvious modification of films was observed after more than 200 days at pH 7.2 and 37 °C. The molar mass of the grafted polymers decreased only slightly during this period, while PHOD films were hydrolyzed into soluble fragments.     

Water sorption and polymer dynamics in hybrid poly(2-hydroxyethyl-co-ethyl acrylate)/silica hydrogels

This work probes the hydration properties and molecular dynamics of hybrid poly(hydroxyethyl-co-ethyl acrylate)/silica hydrogels. Two series of hybrid copolymers were prepared by simultaneous polymerization and silica preparation by sol-gel method, the first with hydroxyethyl acrylate/ethyl acrylate (HEA/EA) composition at 100/0, 90/10, 70/30, 50/50, 30/70, 10/90 and fixed silica content at 20 wt.%, and the second with fixed HEA/EA organic composition at 70/30 and 0, 5, 10 and 20 wt.% of silica. The hydration properties of these systems were studied at 25 °C by exposure to several controlled water vapor atmospheres (water activities 0-0.98) in sealed jars and by immersion in distilled water. Finally, the molecular dynamics of the hydrated hybrids at several levels of hydration was probed with Thermally Stimulated Depolarization Currents (TSDC) in the temperature interval between −150 and 20 °C. The results indicate that a critical region of silica content between 10 and 20 wt.% exists, above which silica is able to form an inorganic network. This silica network prevents the expansion of water clusters inside the hydrogels and subsequently the total stretching of the polymer network without obstructing the water sorption at the first stages of hydration from the dry state. As concerns the copolymer composition, the presence of EA reduces water sorption and formation of water clusters affecting directly to the hydrophilic regions. The TSDC thermograms reveal the presence of a single primary main broad peak denoted as α_cop relaxation process, which is closely related to the copolymer glass transition, and of a secondary relaxation process denoted as β_sw relaxation, which originates from the rotational motions of the lateral hydroxyl groups with attached water molecules. The single α_cop implies structural homogeneity at the nanoscale in HEA-rich samples (x_HEA > 0.5), while for high EA content (x_EA ? 0.5) phase separation is detected. Both relaxation processes show strong dependence on water content and organic phase composition.     

Synthesis and characterization of sulfonated single-walled carbon nanotubes and their performance as solid acid catalyst

Single-walled carbon nanotubes (SWCNTs) were treated with sulfuric acid at 300 °C to synthesize sulfonated SWCNTs (s-SWCNTs), which were characterized by electron microscopy, infrared, Raman and X-ray photoelectron spectroscopy, and thermo analysis. Compared with activated carbon, more sulfonic acid groups can be introduced onto the surfaces of SWCNTs. The high degree (∼20 wt%) of surface sulfonation led to hydrophilic sidewalls that allows the SWCNTs to be uniformly dispersed in water and organic solvents. The high surface acidity of s-SWCNTs was demonstrated by NH₃ temperature-programmed desorption technique and tested by an acetic acid esterification reaction catalyzed by s-SWCNTs. The results show that the water-dispersive s-SWCNTs are an excellent solid acid catalyst and demonstrate the potential of SWCNTs in catalysis applications.     

Principles of quartz crystal microbalance/heat conduction calorimetry: Measurement of the sorption enthalpy of hydrogen in palladium

A sensitive new measurement technology is described which combines calorimetry, gravimetry, and rheology applied to chemical reactions in thin films: quartz crystal microbalance/heat conduction calorimetry (QCM/HCC). The quartz crystal microbalance/heat conduction calorimeters constructed so far simultaneously measure heat generation, mass uptake or release, and viscoelastic property changes in the same, sub-milligram solid film sample when gases interact with the film in an isothermal surrounding. It is possible to measure the energetics of formation of a single layer of adsorbed molecules on a gold surface with this technique. The principles of operation of both the mass and the heat flow sensor are described, and one implementation of the combined sensor and apparatus and its electronics is presented. Methods for calibration and the preparation of thin sample films are summarized. As an illustrative example, the determination of the sorption enthalpy of hydrogen in a 25 °C palladium film of 140 nm thickness is discussed in detail. Other examples of the operation of the QCM/HCC are tabulated.     

Determination of lead in hair and its segmental analysis by solid sampling electrothermal atomic absorption spectrometry

A rapid and practical solid sampling electrothermal atomic absorption spectrometric method was described for the determination of lead in scalp hair. Hair samples were washed once with acetone; thrice with distilled-deionized water and again once with acetone and dried at 75 °C. Typically 0.05 to 1.0 mg of dried samples were inserted on the platforms of solid sampling autosampler. The effects of pyrolysis temperature, atomization temperature, the amount of sample as well as addition of a modifier (Pd/Mg) and/or auxiliary digesting agents (hydrogen peroxide and nitric acid) and/or a surfactant (Triton X-100) on the recovery of lead were investigated. Hair samples were washed once with acetone; thrice with distilled-deionized water and again once with acetone and dried at 75 °C. Typically 0.05 to 1.0 mg of dried samples were inserted on the platforms of solid sampling autosampler. The limit of detection for lead (3σ, N = 10) was 0.3 ng/g The addition of modifier, acids, oxidant and surfactant hardly improved the results. Due to the risk of contamination and relatively high blank values, the lead in hair were determined directly without adding any reagent(s). Finally, the method was applied for the segmental determination of lead concentrations in hair of different persons which is important to know when and how much a person was exposed to the analyte. For this purpose, 0.5 cm of pieces were cut along the one or a few close strands and analyzed by solid sampling.     

Preparation and properties of a thermo-sensitive latex film

Polymer particles with hydrophobic core and hydrophilic shell were prepared via a three-step method. First, poly(butyl methacrylate-co-methyl methacrylate) (p-(BMA-MMA)) latex was prepared through emulsion polymerization. Then, a shell of poly(glycidyl methacrylate) (p-GMA) was introduced around the p-(BMA-MMA) particles by using a redox initiation system under kinetically controlled conditions. Finally, part of the epoxy groups existing in the shell were converted into quaternary ammonium salts, resulting in an ionic hydrophilic shell. The core-shell particles could be redispersed in water to form a stable emulsion. The contact angle of the core-shell latex film with water was around 16° at 25 °C, which became larger than 90° after the film was heated at 150 °C for a short period of time. This showed that the latex film was completely switched from hydrophilicity to hydrophobicity by the action of heat. Additionally, the latex film before heat treatment could be easily washed away from the substrate with neutral water, but it could no longer be removed after the heat treatment. When an IR dye with the maximum absorption at 830 nm was incorporated into the film, it became sensitive to LD laser emitting at 830 nm and gave negative image after exposed by LD laser and developed with neutral water. This showed that the latex film might find uses in chemical-free thermal laser imaging applications.     

Comparative study on hydrolytic degradation and monomer recovery of poly(l-lactic acid) in the solid and in the melt

The hydrolytic degradation of poly(l-lactide) (PLLA) and the formation of its monomer in the solid and in the melt were investigated at 120-150 °C (in the solid), at 160 °C (in the solid up to 40 min and in the melt exceeding 40 min), and at 170-190 °C (in the melt). Such state difference caused the difference in the degradation behavior of PLLA and the behavior of lactic acid formation, although the degradation of PLLA proceeds via a bulk erosion mechanism, regardless of its state. The crystalline residues were formed at the degradation temperatures below 140 °C, but not at the degradation temperatures above 160 °C. The lactic acid yield exceeding 95% can be successfully attained for all the temperatures of 120-190 °C. The activation energy for hydrolytic degradation values of PLLA were 69.6 and 49.6 kJ mol⁻¹ for the temperature ranges of 120-160 °C (in the solid) and 170-250 °C (in the melt), respectively, and are compared with the reported values.     

Behavior of 10-(perfluorohexyl)-decanol, a partially fluorinated analog of hexadecanol, at the air-water interface

10-(Perfluorohexyl)-decanol is a partially fluorinated analog of hexadecanol, an important detergent alcohol. With a melting point of T=48.82 °C and a melting enthalpy of ΔH=53.96 J/g, the intermolecular interactions of the fluorinated alcohol are weaker compared to hexadecanol (T=52.67 °C, ΔH=244.41 J/g). The behavior of this fluorinated alcohol at the air-water interface was studied on five different subphases, namely, water, NaCl (150 mM), CaCl₂ (2 mM), HCl (pH=2.0), and urea (0.5 M). Similar to other partially fluorinated amphiphiles, the compression isotherms of the fluorinated alcohol on all subphases are more expanded compared to the hydrocarbon alcohol with a limiting area of 32-36 Å² per molecule and a temperature-dependent phase transition at 5.6-8.2 mN/m (37 °C, compression rate of 10 mm/min). The dependence of the compression isotherms of 10-(perfluorohexyl)-decanol on subphase composition and temperature follows the trends reported for tetra- and hexadecanol. In particular, a shift to smaller molecular areas with increasing temperatures was observed on all five subphases. The shift to smaller molecular areas on urea indicates that in the case of 10-(perfluorohexyl)-decanol the effect is largely due to a loss of material from the air-water interface during compression of the monolayers. However, a squeezing-out of water molecules from the hydration sphere of the polar headgroup may still occur but can not be unambiguously proven.     

Humidity sensing properties of ZnO-based fibers by electrospinning

Zinc oxide (ZnO) based fibers with a diameter of 80-100 nm were prepared by electrospinning. Polyvinyl alcohol (PVA) and zinc acetate dihydrate were dissolved in water and the polymer/salt solution was electrospun at 2.5 kV cm⁻¹. The resulting electrospun fibers were subjected to calcination at 500 °C for 2 h to obtain ZnO-based fibers. Humidity sensing properties of the fiber mats were investigated by quartz crystal microbalance (QCM) method and electrical measurements. The adsorption kinetics under constant relative humidity (RH) between 10% and 90% were explained using Langmuir adsorption model. Results of the measurements showed that ZnO-based fibers were found to be promising candidate for humidity sensing applications at room temperature.     

Synthesis of photochromic diarylethene polymers for a write-by-light/erase-by-heat recording system

A functionalized styrene monomer (1a) having a photochromic diarylethene chromophore with functional properties of photocoloration, photostability of the colored state, and thermal erasion by heating was synthesized, and the polymer and copolymers of 1a were prepared by radical polymerization and copolymerization. Their polymers exhibited excellent photocoloration and rapid thermal bleaching above 150 °C in solution and in the solid state as well as the performance of the monomeric diarylethene chromophore. In addition, the colored state has a high photostability under visible room light. The diarylethene homopolymer had a glass transition temperature (T_g) as high as polystyrene. The copolymer of 1a with N-1-adamantylmaleimide exhibited extremely high T_g above 200 °C with keeping the photofunctional performance. Such photochromic polymer and copolymers with high T_g can be potentially applied to rewritable display materials and image recordings by a write-by-light/erase-by-heat system.     

Human immunoglobulin adsorption investigated by means of quartz crystal microbalance dissipation, atomic force microscopy, surface acoustic wave, and surface plasmon resonance techniques

Time-resolved adsorption behavior of a human immunoglobin G (hIgG) protein on a hydrophobized gold surface is investigated using multitechniques: quartz crystal microbalance/dissipation (QCM-D) technique; combined surface plasmon resonance (SPR) and Love mode surface acoustic wave (SAW) technique; combined QCM-D and atomic force microscopy (AFM) technique. The adsorbed hIgG forms interfacial structures varying in organization from a submonolayer to a multilayer. An "end-on" IgG orientation in the monolayer film, associated with the surface coverage results, does not corroborate with the effective protein thickness determined from SPR/SAW measurements. This inconsistence is interpreted by a deformation effect induced by conformation change. This conformation change is confirmed by QCM-D measurement. Combined SPR/SAW measurements suggest that the adsorbed protein barely contains water after extended contact with the hydrophobic surface. This limited interfacial hydration also contributed to a continuous conformation change in the adsorbed protein layer. The viscoelastic variation associated with interfacial conformation changes induces about 1.5 times overestimation of the mass uptake in the QCM-D measurements. The merit of combined multitechnique measurements is demonstrated.     

The effect of fluorine substituents on the polymerization mechanism of 2-methylene-1,3-dioxolane and properties of the polymer products

Perfluoro-2-methylene-1,3-dioxolane (III) was synthesized and polymerized with an initiator, perfluoro dibenzoyl peroxide, and a white solid product III-P was quantitatively isolated. The polymer was insoluble in organic solvents including fluorinated solvents such as Fluorinert FC 75 and hexafluorobenzene, but dissolved in hexafluorobenzene by heating at around 140 °C in a sealed ampoule. The X-ray measurement showed that III-P was semi-crystalline and melted at 230 °C. The IR spectrum of III-P indicated that the polymer obtained did not show carbonyl peak and it was the vinyl addition product. When the solid product was heated above the melting temperature and pressed under 100-200 kg/cm², we obtained an amorphous and flexible film, which is transparent from the UV region to the near IR region. The glass transition temperature was 110 °C and refractive indexes were 1.3443, 1.3434 and 1.3373 at 633, 839 and 1544 nm, respectively. The film did not degrade in concentrated sulfuric acid and aqueous sodium hydroxide solutions even heated at 80-90 °C for 2 days. The film was thermally stable and began to decompose at 300 °C under air atmosphere.     

Fibronectin adsorption on gold, Ti-, and Ta-oxide investigated by QCM-D and RSA modelling

The adsorption of fibronectin on gold, Ti-, and Ta-oxide surfaces is investigated by means of the quartz crystal microbalance with dissipation (QCM-D) technique. The surface chemistry (gold, Ti-, and Ta-oxide) is found to influence the frequency shift observed during adsorption of the fibronectin layer with the magnitude being Delta f Au>Delta f Ti-oxide approximately Delta f Ta-oxide. Corresponding variations in the dissipation change normalised to frequency change (Delta D/Delta f) for the layer are observed. The QCM-D data are further analyzed by the random sequential adsorption (RSA) model, and adsorption rate parameter ka and footprint (a) determined, which supported the trend seen in the Delta f and Delta D/Delta f values. The value of ka found by the RSA modelling of the QCM-D resonance frequency data is found to match the ratio between the mass measured by QCM-D and the mass reported by optical techniques in literature. We conclude that comparison of the adsorption rate parameter (ka) obtained by RSA modelling of the QCM-D data with ka values obtained from RSA modelling of data obtained using optical techniques can be a route to determine the degree of hydration of the adsorbed protein layer.     

Conformation of oligo(ethylene glycol) grafted poly(norbornene) in solutions: A small angle neutron scattering study

The conformation of newly synthesized amphiphilic poly(methoxyoligo(ethylene oxide) norbornenyl esters) macro-homopolymers in dilute solutions of toluene-d8 and D₂O was investigated by small angle neutron scattering (SANS). The macro-homopolymers consist of a polynorbornene (PNB) backbone with a degree of polymerization (DP) of 50, and each repeat unit has a grafted ethylene glycol (EG) side chain with an average DP of 6.6. The hydrophobic backbone and hydrophilic side chains interact differently with solvents of different polarity, which makes the polymer conformation very sensitive to the solvent quality. It was found that in a 0.5 wt.% toluene solution the polymers assume coil-like conformation and gradually contract and become more compact with increasing polymer concentration. In D₂O, the conformation of the polymers were studied at different concentrations: 0.1, 0.5, 1.0 and 2.0 wt.% and at different temperatures: 25, 44, 60 and 74 °C. The polymers are partially contracted in D₂O and their shape can be described by the form factor of a rigid cylinder. The second virial coefficient A₂ was extracted at three temperatures (25, 44 and 60 °C) and the theta point was estimated to be reached at ∼45 °C. The attractive interactions between the polymers in D₂O increase with temperature, which leads to the polymer-solvent phase separation at the cloud point temperature (CPT). The polymer conformation remains virtually temperature independent below the CPT and at 74 °C polymers collapse and form compact structures with water soluble side chains in the shell.     

Molecular dynamics simulation on ion-pair association of NaCl from ambient to supercritical water

Molecular dynamics (MD) simulations for aqueous NaCl solution were performed from ambient to supercritical conditions (25 °C, 1.0 g cm⁻³; 250–350 °C, 0.67–0.8 g cm⁻³; 380 °C, 0.2–0.8 g cm⁻³; and 400–600 °C, 0.4 and 0.7 g cm⁻³) in the canonical ensemble to examine how the hydration structure relates with the thermodynamics of the ion-pair association. Hydration structure and the potential of mean force (PMF) of Na⁺Cl⁻ ion-pair were calculated. Ion-pair association constants were also calculated from the PMFs. Energies and entropies of the ion-pair at arbitrary inter-ionic distances from 2.0 to 8.0 Å were evaluated from the temperature derivative of the PMFs. From the calculation of energies and entropies, Na⁺–Cl⁻ pair association was found to be endothermic and promoted by the entropy gain. PMFs had minimums and a slight maximum corresponding to CIP, SShIP, and the transition state between CIP and SShIP, and similar minimums and maximum were only observed for the energy term and not clearly observed for the entropy term. This result indicates that the shape of the PMF and stability of SShIP are determined by the energy of the system. Relationship between the hydration structure and the energy of the system was examined and it was confirmed that the hydration structure in the first hydration shell of the ion-pair was one of the important factor, which made the minimums and maximum in the energy terms and PMFs, and stabilized the SShIP structure.     

Preparation and properties of Nafion/hollow silica spheres composite membranes

In present work, hollow silica spheres (HSS)/Nafion^® composite membranes were prepared by solution casting. The thermal properties, water retention, swelling behavior and proton conductivity of the composite membranes were explored. It was found that HSS dispersed well at micrometer scale in the obtained composite membranes by SEM and TEM observation. Thermal properties of composite membranes were improved than that of recast Nafion^® membrane. Compared with the recast Nafion^® membrane, the composite membranes showed higher water uptake and lower swelling degree at the temperature range from 40 to 100 °C. At the same HSS loading, the smaller the diameter of HSS in composite membranes, the more the water uptake, however, the swelling degree of composite membranes was increased. The proton conductivity of the composite membrane with 3–5 wt.% HSS (120 and 250 nm) increased distinctively at above 60 °C, reached the optimal value at 100 °C, and decreased slowly when the temperature exceeded 100 °C.     

Thermal behavior of aluminum powder and potassium perchlorate mixtures by DTA and TG

In this work the thermal decomposition characteristics of micron sized aluminum powder + potassium perchlorate pyrotechnic systems were studied with thermal analytical techniques. The results show that the reactivity of aluminum powder in air increases as the particle size decreases. Pure aluminum with 5 μm particle size has a fusion temperature about 647 °C, but this temperature for 18 μm powder is 660 °C. Pure potassium perchlorate has an endothermic peak at 300 °C corresponding to a rhombic-cubic transition, a fusion temperature around 590 °C and decomposes at 592 °C. DTA curves for Al₅/KClO₄ (30:70) mixture show a maximum peak temperature for thermal decomposition at 400 °C. Increasing the particle size of aluminum powder increases the ignition temperature of the mixture. The oxidation temperature increased by enhance in the aluminum content of the mixture.