激光脉冲宽度对有质动力加速电子的影响

基于真空中单电子运动模型,编程计算得到了高斯激光脉冲与初始位于激光传播轴上电子的相互作用结果。不同激光参鼍条件下,得到了电子的能量增益与激光强度、焦斑大小和脉冲宽度关系。结果表明,高斯激光脉冲焦斑较大时,电子没有明显的能量增益,高斯激光脉冲焦斑太小时,电子也没有明显的能量增益。电子的能量增益有一个最佳焦斑大小。在相同激光强度下,电子能量增益的最佳焦斑大小随脉冲宽度的增大而增大,但最佳焦斑大小与脉冲宽度的比值基本上是不变的。     

激光脉冲宽度对远距离尾流气泡后向检测的影响

为了分析激光脉冲宽度对远距离尾流气泡后向检测的影响,基于Fournier Forand体积散射函数,通过Monte Carlo方法建立了水中激光脉冲后向散射信号时域特征的分析模型.利用该模型研究了初始激光脉冲宽度不同时,水中远距离舰船尾流气泡的激光脉冲后向散射信号变化情况.结果表明:随着初始激光脉冲宽度的增加,后向散射信号中水体散射信号与尾流气泡回波信号的轮廓变得模糊|当脉冲宽度增大到一定程度时,无法从后向散射信号中辨别出回波信号|并且,随着尾流区气泡散射强度的减小以及气泡区与检测器之间距离的减短,这种变化趋势变得更加明显.基于仿真结果,提出一种基于逆卷积运算的尾流气泡回波信号提取方法.     

激光脉冲对氢负离子在金属面附近光剥离的影响

利用闭合轨道理论和金属面附近氢负离子的双脉冲光剥离截面的计算公式,计算了氢负离子在金属面附近激光脉冲作用下的光剥离截面.计算结果表明:如果脉冲宽度远大于闭合轨道的回归周期时,它对光剥离截面的影响很小;当脉冲宽度小于闭合轨道的周期或者可以和闭合轨道的周期相比较时,光剥离截面的振荡幅度大大地减弱.光剥离截面除了与脉冲宽度有关外,还与双脉冲之间的时间延迟、相位差有关.对于某些相位差, 双脉冲光剥离截面的取值增大; 而对于另外一些相位差, 光剥离截面的取值减小.因此,可以利用脉冲激光来控制氢负离子在表面附近光剥离 关键词： 激光脉冲 光剥离截面 金属面 闭合轨道理论     

Irradiation effects of CO2 laser parameters on surface morphology of fused silica

To understand the surface morphology evolution of fused silica induced by 10.6-μm CO2 laser irradiation at different parameters,this paper reports that optical microscopy,profilometry,and hydrophilicity tests are utilized to characterize the surface structure and roughness of the laser irradiated area. The results show that three typical surface morphologies and two typical hydrophilicity test images are observed at different laser powers and pulse durations. The correlations between surface temperature and surface morphology as well as hydrophilicity behaviours are presented. The different hydrophilicity behaviours are related to surface structures of the laser-induced crater and thermal diffusion area. The thermal diffusion length monotonously increases with increasing laser power and pulse duration. The crater width is almost determined by the laser beam size. The crater depth is more sensitive to the laser power and pulse duration than the crater width.     

High repetition rate femtosecond laser nano-machining of thin films

Thin film laser micromachining has been utilized for repairing semiconductor masks, creating solar cells and fabricating MEMS devices. A unique high repetition rate femtosecond fiber laser system capable of variable repetition rates from 200 KHz to 25 MHz along with helium gas assist was used to study the effect of pulse repetition rate and pulse energy on femtosecond laser machining of gold-coated silicon wafer. It was seen that high repetition rates lead to smaller craters with uniform line width. Craters created at 13 MHz pulse repetition rate with 2.042 J/cm² beam energy fluence measured 110 nm in width and had a heat affected zone of 0.79 μm. It was found that pulse repetition rate only played a significant role in the size of the heat affected zone in the lower pulse energy ranges. In the future, a 1 W laser system will be acquired to find the optimal repetition rate that would create the minimal feature size with the least heat affected zone. Using this kind of setup along with techniques such as radial polarization and a different gas assist may enable us to create sub 100 nm feature size with good quality.     

Effect of pulse width and fluence of femtosecond laser on the size of nanobump array

Conical nanobump arrays were generated on gold thin film processed by interfering femtosecond laser. The transition of the height and diameter as functions of fluence and pulse width was investigated. When the fluence was 87 mJ/cm², the height and diameter were not so different at 350 fs or shorter pulse width. They decreased at longer pulse width, and no bump could be generated over 1.6 ps. The results suggest the decrease of size is due to the diffusion of electron to not-excited region, and due to heat conduction to not heated region or substrate, or change of absorbance of laser. At long pulse width of 2.4 ps and relatively higher fluence of 190 mJ/cm², nanobump had liquid-like structure as a stop motion of a water drop.     

激光在烟幕中传输的蒙特卡罗模拟

建立蒙特卡罗计算模型,模拟计算1.06μm脉冲激光在石墨烟幕中的传输.分析透过率与石墨粒子粒径、烟幕浓度、烟幕厚度的关系,用卷积方法计算一定宽度的脉冲激光穿过烟幕后的波形,数值仿真δ脉冲和矩形脉冲激光在各种石墨烟幕中的时间展宽特性.模拟结果表明:石墨粒子存在一最佳半径(0.16μm),该半径的石墨粒子烟幕不仅使激光能量衰减最强,而且产生的时间展宽也最显著;激光脉冲宽度越小,其波形变化和时间展宽越显著,微秒量级脉宽的激光脉冲穿过烟幕后波形变化和时间展宽效应不明显.     

串联式电光开关实现光脉冲宽度大范围可调

为了获得大范围脉宽可调的光脉冲,以连续激光为光源,采用两个外腔调制型电光开关,将该连续激光调制成单脉冲光源.其中两个外腔调制型电光开关采用串联方式工作,两者之间的检偏方向相互垂直,由第一级电光开关实现激光脉冲的快速开启,第二级电光开关实现激光脉冲的快速关闭.通过延时同步机对两个电光开关的动作时间进行控制,从而实现光脉冲宽度大范围可调.实验研究获得了最窄脉冲宽度40 ns,最宽脉冲宽度400 μs的532 nm激光脉冲.     

YAG laser percussion drilling of a functional multi-layer thin plate

An Au-coated Fe–Ni alloy thin plate was laser drilled by a pulsed Nd:YAG laser. The influences of laser parameters on the diameter of perforation, the outer diameter of crater and the roundness of the perforation have been investigated by employing scanning electron microscopy. The diameter of perforation increases gradually with an increase in pulse width from 0.3 to 8 ms at the fixed average laser power and frequency, and increases with an increase in average laser power from 10 to 25 W at the fixed pulse width and frequency. Some craters are found around the perforations because of the heat affecting of laser beam to the non-irradiated zone. The diametric difference of the perforation between the incident and the effluent sides is very small under the shortest pulse width of 0.3 ms. Good roundness of the perforation can be achieved at either the lowest pulse width or the lowest laser power.     

脉冲单频Nd:YVO4激光器及其倍频输出特性研究

为了研制激光干涉成像所需的主振荡功率放大(MOPA)结构脉冲单频激光器,本文完成MOPA激光器的种子源即声光调Q脉冲单频1 064 nm激光器的特性研究,同时完成种子源腔外倍频绿光特性研究。脉冲单频激光器采用声光调Q模块实现脉宽约20 ns的1 064 nm脉冲激光输出,采用环形腔设计并采用一组不同厚度的标准具实现单纵模运转。实验研究基频1 064nm和倍频532 nm激光脉冲的线宽,得出在全脉宽范围内都具有较高时间相干性的结论。实验分别获得脉宽约28 ns峰值功率约6.5 kW的1 064 nm脉冲单频激光和脉宽约20 ns、峰值功率约0.5 kW的532 nm脉冲单频激光,腔外倍频效率为5.6%。实验同时也验证了腔外倍频的激光脉宽压缩效应。     

Spatiotemporal Evolution of Intense Short Gaussian Laser Pulses in Weakly Relativistic Magnetized Plasma

The weakly relativistic regime of propagation of a short and intense laser pulse in the magnetized plasma is investigated. By considering relativistic nonlinearity and using non‐linear Schrödinger equation with paraxial approximation, two second‐order coupled differential equations are obtained for the longitudinal pulse width parameter (in time) and for the transverse pulse width parameter (in space). The simultaneous evolution of spot size and length of a relativistic Gaussian laser pulse in a magnetized plasma can be calculated by the numerical solution of the equations. The effect of magnetic field is investigated. It is observed that in the presence of magnetic field both the self‐compression and the self‐focusing can be enhanced. Furthermore, the interplay between the longitudinal self‐compression and the transverse self‐focusing in a magnetized plasma is investigated. (© 2016 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Generation of 1.5-12 ns width-tunable 532 nm pulses by adopting laser-induced plasma shutter technique

The pulse-shaping technique has found widespread applications in nonlinear optics and material processing. Experimental research on laser-induced plasma shutter to control the 532 nm pulse width is conducted. The impacts of the total pulse output energy on pulse compression are investigated, and a useful conclusion can be drawn that there exists an optimal value of pulse energy at which the shortest output pulse of 3.23 ns can be obtained without a device for delay-time. Once the device for delay-time is employed to change the optical differences between two laser paths, the pulse width can be further shortened to 1.51 ns. In short, the 1.5-12 ns width-tunable 532 nm laser pulses have been obtained by adopting the laser-induced plasma shutter technique.     

斩波法在激光微能量计标定中的应用

针对激光微能量测量的问题,提出一种激光微能量计标定新方法与装置。研究内容包括使用稳功率连续激光作为光源,通过基于斩波的脉冲发生器组件产生微能量的脉冲激光,分别使用脉冲宽度测量组件与功率测量组件进行采集、软件分析,计算微能量值及通过比对给出待标定能量计的修正系数,计算机自动控制。结果表明,该方法获得的脉冲激光波形稳定,脉冲宽度测量不确定度为0.08%,激光功率测量不确定度为0.25%,实现了对0.1 pJ～1 mJ的激光能量进行准确复现和传递。     

Facile one-step sonochemical synthesis of ultrafine and stable fluorescent C-dots

This work describes a one-step synthesis of carbon dots (C-dots), which is carried out by sonication of polyethylene glycol (PEG-400) for 0.5–3 h. The effect of the various experimental parameters, such as sonication time, amplitude and temperature on the size and the fluorescence of the C-dots was studied. It was found that the average diameter of the C-dots is between 2 and 9 nm, depending on the preparation conditions. The highest quantum yield of emission was ∼16%. These high fluorescence properties of the C-dots could be used for bioimaging and for solar cell applications.     

Coherent control of photodetachment of H− in an electric field near a metal surface

We show that the photodetachment of H^? in an electric field near a metal surface can be controlled by using a single or double laser pulse. The method of theoretical analysis used is semi-classical closed orbit theory. The results show that if the period of a certain closed orbit is longer than the pulse width of the single-pulse laser, the contribution of that closed orbit to the photodetachment cross-section will be greatly reduced. As for the double-pulse laser, the pulse width, phase difference and the time delay between the two pulses all play an important role in the photodetachment cross-section. With the decrease of the time delay, the oscillating amplitude of the cross-section increases while the oscillating frequency decreases. Therefore, laser pulses can be used to control the photodetachment process of negative ions or atoms in an external field near metal surfaces.     

A Diode-Pumped Actively Q-Switched and Injection-Seeded Tm:LuAG Laser at Room Temperature

We elaborate a diode-end-pumped actively Q-switched injection-seeded Tm:LuAG laser. To achieve power scaling with good beam quality, we construct a more flexible laser with longer cavity accommodated strongly aberrated thermal lens in a Tm:LuAG laser and took special care in designing the laser resonator. Under Q-switched operation, we achieve a maximum output energy of 2.6 mJ with a pulse width of 318.2 ns at a pulse repetition frequency of 50 Hz. To control the spectral, temporal, and phase characteristics of the Tm:LuAG laser, the ring laser is injected by a seed laser, which provides a 50 mW single longitudinal-mode laser output at a wavelength of 2,022.6 nm. We achieve an output energy of 1.8 mJ with a pulse width of 293.0 ns after employing the injection seed.     

Passively Q-switched and mode-locked 1.3 μm Nd:YAG laser with Co:LMA saturable absorber

An xenon-lamp-pumped passively Q-switched and mode-locked (QML) Nd:YAG laser with Co:LMA saturable absorber at 1.3 μm is realized in a straight cavity. The modulation depth of mode locking pulse has reached 100%. The pulse energy and the pulse width of QML laser have been measured. The pulse width of the mode-locking laser is estamated to be 940 ps.     

利用NOLM实现连续光到归零码脉冲和波长的同时变换

利用非线性光学环路镜成功地实现了连续光到超短光脉冲和波长的同时变换.最大波长变换间距大于35nm.实验系统中采用增益开关分布反馈半导体激光器(GSDFB-LD)产生的超短光脉冲作为控制光,采用波长可调半导体激光器作为信号光.在变换过程中在1.55μm附近首次观测到了波长的反相变换.当信号光和控制光脉冲走离大于40.7ps时,变换信号脉冲发生畸变,变换脉冲展宽.     

线性模式下GaAs光电导开关的时间抖动特性

针对线性模式下GaAs光电导开关时间抖动特性的研究,对提高精密同步控制系统的输出性能具有重要意义.根据电脉冲的概率分布和时间与电脉冲波形的对应关系,结合载流子的输运过程,对光电导开关时间抖动进行了定性的理论推导.此外,通过搭建实验平台,利用正交光栅分光,将一束激光同时触发两路并联的GaAs光电导开关,改变触发激光脉冲宽度及外加偏置电压测试开关时间抖动,根据实验值的对比分析,得出在不同的外加偏置电压下,随着触发激光脉冲宽度的减小,开关时间抖动值随之减小.验证了触发激光脉冲宽度对开关时间抖动的影响及理论分析的正确性.研究结果对GaAs光电导开关时间抖动的进一步减小具有一定的指导意义.     

The Process of a Laser-Supported Combustion Wave Induced by Millisecond Pulsed Laser on Aluminum Alloy

We study the process of a laser-supported combustion wave(LSCW) when an aluminum alloy is irradiated by a millisecond pulse laser based on the method of laser shadowgraphy.Under the condition of different laser parameters,the obtained results include the velocity,ignition threshold of LSCW and the variation law.The speed of LSCW increases with the laser energy under the same irradiation laser pulse width,and the speed of LSCW reduces with the increase of the laser pulse width under the same irradiation laser energy.Moreover,the ignition time of LSCW becomes shorter by increasing the laser number of the pulse and is not effected by changing the frequencies,when keeping the laser pulse width and energy unchanged.The results of the study can be applied in the laser propulsion technology and metal surface laser heat treatment,etc.