Elimination of adsorption effects in the analysis of water-soluble vitamins in pharmaceutical formulations by capillary electrophoresis.

A tendency to an increase in migration times was observed when different water-soluble vitamins were analysed repeatedly in pharmaceutical preparations by capillary electrophoresis. In order to better understand the origin of this effect, the influence of the vitamins and the excipients, such as cellulose derivatives, was investigated. These studies indicated that the increase in analyte migration times was most probably due to the adsorption of different kinds of constituents to the capillary wall. Different rinsing procedures were tested in order to eliminate these unfavourable effects. A rinse of the capillary with a 25 mM sodium dodecyl sulfate (SDS) solution in the running buffer between successive runs was found to be particularly effective when the analysis was performed by free solution capillary zone electrophoresis (CZE). When the vitamins were determined by micellar electrokinetic chromatography (MEKC) using SDS as surfactant, a short capillary rinse with the running buffer was sufficient to obtain reproducible migration times. The CZE and MEKC methods developed were validated and compared. Both methods could be applied to the determination of water-soluble vitamins in different multivitamin formulations.     

Analysis of synthetic chemical drugs in adulterated Chinese medicines by capillary electrophoresis/electrospray ionization mass spectrometry

Sixteen synthetic chemical drugs, often found in adulterated Chinese medicines, were studied by capillary electrophoresis/UV absorbance (CE/UV) and capillary electrophoresis/electrospray ionization mass spectrometry (CE/ESI-MS). Only nine peaks were detected with CZE/UV, but on-line CZE/MS provided clear identification for most compounds. For a real sample of a Chinese medicinal preparation, a few adulterants were identified by their migration times and protonated molecular ions. For coeluting compounds, more reliable identification was achieved by MS/MS in selected reaction monitoring mode. Micellar electrokinetic chromatography (MEKC) using sodium dodecyl sulfate (SDS) provided better separation than capillary zone electrophoresis (CZE), and, under optimal conditions, fourteen peaks were detected using UV detection. In ESI, the interference of SDS was less severe in positive ion mode than in negative ion mode. Up to 20 mM SDS could be used in direct coupling of MEKC with ESI-MS if the mass spectrometer was operated in positive ion mode. Because of better resolution in MEKC, adulterants can be identified without the use of MS/MS.     

Optimization of solid-phase extraction and solid-phase microextraction for the determination of alpha- and beta-endosulfan in water by gas chromatography-electron-capture detection

The electrophoretic behaviour of ionizable and neutral alkylxanthines commonly used in pharmaceutical preparations was studied. The performance of various separation modes including capillary zone electrophoresis (CZE), cyclodextrin electrokinetic chromatography, and micellar electrokinetic chromatography (MEKC) with either sodium dodecyl sulfate (SDS) or bile salts as surfactants, was assessed. CZE in an alkaline medium successfully separates ionizable xanthines and dyphylline. The addition of carboxymethyl-β-cyclodextrin to the background electrolyte allows only partial resolution of neutral xanthines. Based on MEKC results, bile salts exhibit more discrimination ability than SDS to separate similar xanthines. The best results are provided by taurodeoxycholic acid, which ensures baseline separation of xanthines.     

Online concentration of aristolochic acid I and II in Chinese medicine preparations by micellar electrokinetic chromatography

In this study, an online concentration method in micellar electrokinetic chromatography (MEKC) applying field-enhanced sample injection (FESI) mode was developed for the detection of aristolochic acids (AAs) in Chinese medicine preparations. AA-I and AA-II were baseline separated with high separation efficiency, and 100-fold enhancement of the detection sensitivity was achieved compared with those obtained from normal capillary zone electrophoresis (CZE) or simple MEKC method. The proposed method was successfully applied for the determination of AAs in Chinese medicine preparations.     

Evaluation of capillary electrophoretic techniques towards systematic toxicological analysis.

Two capillary electrophoresis (CE) methods were evaluated for their suitability in systematic toxicological analysis (STA). A test set of 25 barbiturates was analysed using capillary zone electrophoresis (CZE) and micellar electrokinetic chromatography (MEKC). Buffers used consisted of 90 mM borate set at pH 8.4 (CZE) and 20 mM phosphate, 50 mM sodium dodecyl sulphate set at pH 7.5 (MEKC). All analyses were carried out using fused silica capillaries using an electric field strength of 52.6 kV/m. The use of a reproducible identification parameter is very important in STA as it influences the identification power (IP). To deal with the poor reproducibility of the migration time, we introduced the corrected effective mobility. Inter-day reproducibilities of the latter parameter were < 0.6% for CZE and < 0.5% for MEKC, using daily prepared buffers. The IP of the methods was expressed by calculation of the discriminating power and the mean list length. Data obtained were compared to gas chromatographic and high-performance liquid chromatographic data, and correlations between all methods were calculated. It was shown that little correlation exists between chromatographic and electrophoretic techniques. The results indicated that CE has a good identification power for the application in STA, especially when a combination of methods having a low correlation is used.     

Capillary electrophoresis on unmodified genetically coded amino acids

The separation of mixtures of free genetically coded amino acids by capillary zone electrophoresis (CZE) and micellar electrokinetic chromatography (MEKC) using UV and refractometric detection was studied. Mixtures of 16 and 14 amino acids were separated by CZE and MEKC, respectively.     

Capillary electrophoretic determination of the constituents of Artemisiae Capillaris Herba

Two capillary electrophoretic methods, a micellar electrokinetic electrophoretic (MEKC) one and a capillary zone electrophoretic (CZE) one, were developed for the separation of 12 constituents in Artemisiae Capillaris Herba. Detection at 254 nm with 20 mM sodium dodecyl sulfate and 20 mM sodium borate buffer (pH 9.82) in MEKC or with 25 mM sodium borate and 6.75 mg/ml 2,3,6-tri-O-methyl-beta-cyclodextrin buffer in CZE was found to be the most suitable approach for this analysis. Within 42 min, the MEKC method could successfully separate 12 authentic constituents, whereof chlorogenic acid, however, appeared as a broad and split peak, and capillarisin and chlorogenic acid overlapped partially with other coexisting substances in crude extract of the herb. The CZE method could completely overcome these problems and was used to determine the amounts of capillarisin, chlorogenic acid, scopoletin and caffeic acid in the extract. The effect of buffers on the constituent separation and the validation of the two methods were discussed.     

Interlaboratory reproducibility of mobility parameters in capillary electrophoresis for substance identification in systematic toxicological analysis

An interlaboratory pilot study was performed to determine the reproducibility of mobility parameters in capillary zone electrophoresis (CZE) and micellar electrokinetic chromatography (MEKC). The study was performed by an intended small number of laboratories (three) that used different brands of instruments (two). The effective mobility was corrected using standards by a method that was recently introduced to obtain a more reproducible migration parameter. A test set of 20 acidic test compounds and 5 reference compounds were analyzed during five days in each laboratory using CZE and MEKC. Buffers used consisted of 90 mM borate set at pH 8.4 (CZE) and 20 mM phosphate, 50 mM sodium dodecyl sulfate set at pH 7.5 (MEKC). Analyses were carried out using fused-silica capillaries at an electric field strength of either 52.6 kV/m or 37.5 kV/m. The interlaboratory reproducibility (mean RSD) of the effective mobility was 3.0% for CZE and 6.7% for MEKC. After applying the correction method, these values became 3.0% for CZE and 3.3% for MEKC, which is adequate for systematic toxicological analysis (STA) applications. A significant improvement of reproducibility for the calculated corrected effective mobility mu(eff)c was observed when variations are high. Therefore, it is recommended to use the correction method in interlaboratory situations, especially when instruments and capillaries from different manufacturers are used.     

Comparative study of capillary zone electrophoresis and micellar electrokinetic chromatography for the separation of twelve aromatic sulphonate compounds

Summary Two modes of capillary electrophoresis (CE), capillary zone electrophoresis (CZE) and micellar electrokinetic chromatography (MEKC), were investigated for the separation of 12 aromatic sulphonate compounds. In CZE, although the voltage applied, the buffer concentration and the pH were optimized for effective separation of the compounds studied, under the best conditions four of the five amino compounds coeluted, as did naphthalene-1-sulphonic acid and naphthalene-2-sulphonic acid. In MEKC, sodium dodecyl sulphate (SDS) and Brij 35 were chosen as the anionic and nonionic surfactants and the effect of the concentration of micelles was examined. The effect of adding methanol as the organic modifier was also investigated with each of these micellar systems. All the analytes, including the isomers, were completely separated by use of MEKC with Brij 35 but when SDS was used only 11 compounds were separated because two amino compounds coeluted.     

在线富集二维毛细管电泳分析新体系检测尿样中药物及对映体

将在线富集技术同二维(2D)毛细管电泳(CE)分离相结合同时提高复杂样品中痕量组分的分离度和检测灵敏度.毛细管区带电泳(CZE)作为第一维,分析物根据淌度不同进行分离,第一维流出组分进入第二维毛细管,根据分配系数不同进行胶束电动毛细管色谱(MEKC)分离.采用阳离子选择性耗尽进样(CSEI)在柱预富集,延长进样时间,增大进样量;同时在二维毛细管接口处采用动态pH联接/胶束扫集在线富集技术不仅避免第一维分离组分在接口处扩散,还可进一步压缩样品区带.同常规电动进样CE分离相比,该在线富集二维分离技术的分离能力远远高于一维CZE或MEKC分离,富集倍数达到(0.5～1.2)×104.该法成功应用于人体尿样中四种药物及对映体的分析测定,浓度检出限为0.1～0.3μg/L.进一步研究了人体尿样中四种药物24h内的药代动力学规律.     

Study of the Electrophoretic Behaviour of Flavonoids

The electrophoretic behaviour of 13 flavonoids commonly found in medicinal plants has been studied. The performance of two modes of separation, capillary zone electrophoresis (CZE) and micellar electrokinetic capillary chromatography (MEKC), was assessed and compared. MEKC was found to be more effective for separation of the analytes. The effect of structure on the electrophoretic behaviour of the flavonoids is also discussed.     

不同缓冲体系对毛细管电泳法分离15种核苷类化合物效果的比较

对毛细管电泳法分离15种核苷类化合物所用的不同缓冲液体系进行了系统比较,确定不同模式毛细管电泳法分析多种核苷类化合物的最适合背景缓冲液体系(BGE)。分别以四硼酸钠、磷酸氢二钠、乙酸钠、碳酸氢钠、乙酸铵和乙二胺(DEA)为背景电解质,对毛细管区带电泳(CZE)、毛细管电泳-电喷雾飞行时间质谱(CE-ESI-TOF/MS)以及胶束电动毛细管电泳(MEKC)3种模式进行比较,并对其中几种优势缓冲体系进行了优化。结果表明,CZE模式下使用四硼酸钠和磷酸氢二钠缓冲体系无法同时分离15种核苷类化合物,因此只适用于分析核苷类化合物数量较少的样品。而使用含有2%丙酮的300 mmol/L DEA能完全分开15种核苷类化合物,且分辨率和峰形良好。MEKC模式下,以25 mmol/L磷酸氢二钠(添加70 mmol/L十二烷基磺酸钠(SDS))为缓冲盐的分离结果最佳,并且此方法能成功应用于海洋生物海葵中核苷类化合物的分离。CE-ESI-TOF/MS分析中,以20 mmol/L乙酸铵(pH 10.0)为背景电解质,正离子模式检测,15种核苷类化合物的质谱信号均良好,检测灵敏度明显优于文献中报道的使用DEA缓冲体系的结果。本研究阐明了不同缓冲体系对15种核苷类化合物分离的适用性,为毛细管电泳技术在复杂基质中多种核苷类化合物的分离方法中的应用奠定了基础。     

Analysis of organic components of smokeless gunpowders: high-performance liquid chromatogaphy vs. micellar electrokinetic capillary chromatography

The aim of the present study was to verify the analytical performances of high-performance liquid chromatography (HPLC) and micellar electrokinetic capillary chromatography (MEKC) for the separation and qualitative determination of a selected group of organic components of smokeless gunpowders. The HPLC method was based on a gradient reversed-phase elution with a mobile phase composed of 0.17 M H(3)PO(4)/methanol; detection was performed by UV absorption at the wavelengths of 220, 254, and 270 nm. The MEKC experiments were carried out by using uncoated fused-silica capillaries (50 microm inside diameter, 50 cm effective length) and a running buffer composed of 10 mM sodium tetraborate at pH 9.24 added with 25 mM sodium dodecyl sulfate (SDS); the applied voltage was 25 kV; detection was either at a fixed wavelength UV of 214 nm or with a diode-array detector operating in the wavelength range from 190 to 350 nm. Both reversed-phase HPLC and MEKC techniques succeeded in resolving the tested standard mixtures of organic components of smokeless powders. Although the sequence of elution of the different analytes was slightly different between HPLC and MEKC, a statistical analysis based on the Spearman's rank correlation test showed that the two separation patterns were highly correlated. HPLC and MEKC were comparable in terms of elution/migration time precision, whereas MEKC showed higher reproducibility of peak areas. The interfacing of capillary electrophoresis with diode array UV detection provided distinct UV spectra of the individual analytes, thus improving, on the detection side, the analytical selectivity and identification power of capillary electrophoresis.     

Profiling and screening analysis of 27 aromatic amino acids by capillary electrophoresis in dual modes

An efficient capillary electrophoretic (CE) profiling and screening system based on dual modes of capillary zone electrophoresis (CZE) and micellar electrokinetic capillary chromatography (MEKC) was developed for the simultaneous determination of 23 nonprotein amino acids (NPAAs) and 4 protein amino acids with aromatic moiety. It involves separation by an uncoated fused-silica capillary under phosphoric acid buffer in CZE mode and by another uncoated fused-silica capillary under neutral sodium dihydrogen phosphate buffer containing sodium dodecyl sulfate in MEKC mode. Migration orders of the amino acids studied on the two separation modes under each optimum condition were very different. The repeatability of migration times measured by the CZE and MEKC was found to be better than 4.8 and 3.4%, respectively, thereby enabling to cross-check the identification of each amino acid. The method linearity and limit of detection of the CZE for each amino acid were found to be adequate for the assay of aromatic amino acids. When the present CE profiling and screening analysis in dual modes was applied to plant seeds, NPAAs such as mimosine from Mimosa pudica Linné, and 2-phenylglycine from Lindera erythrocarpa Makino were positively detected along with tryptophan, phenylalanine and tyrosine.     

Development of an analytical method for beryllium in airborne dust by micellar electrokinetic chromatography

The separation of diacetylacetonato–beryllium [Be(acac)₂] from acetylacetone was achieved with micellar electrokinetic chromatography (MEKC) followed by subsequent beryllium analysis carried out using capillary electrophoresis. Analysis using a separation and absorption detector, with a 50 μm capillary cell, could detect approximately 1000 ppb of beryllium in the final sample. Be(acac)₂ is a promising reagent for absorption spectrophotometry, because its molar absorption coefficient, (32 000 l mol⁻¹ cm⁻¹) is very large. As the complex and acetylacetone have a similar absorption wavelength, the excess free ligand must removed from the sample to be measured. Acetylacetone is a weak acid with keto–enol tautomerism in aqueous solution. Acetylacetone and neutral Be(acac)₂ should be separated with capillary zone electrophoresis (CZE) using a neutral or basic buffer solution as the mobile phase. Although the pH and temperature of the mobile phase were optimized, separation with CZE was interfered with by a portion of acetylacetone. This interfering portion seems to be a neutral keto-form with the same migration time as Be(acac)₂. As a neutral species separation method, MEKC with sodium dodecyl sulfate was tried and the separation was completed. The optimum pH value and buffer temperature are pH 7.8 and 15°C, respectively.     

Intra- and interinstrument reproducibility of migration parameters in capillary electrophoresis for substance identification in systematic toxicological analysis

The intra- and interinstrument reproducibilities of four capillary electrophoresis instruments were studied for identification purposes in systematic toxicological analysis (STA). A test set of 20 acidic test compounds and 5 reference compounds were analyzed for five days on each instrument using capillary zone electrophoresis (CZE) and micellar electrokinetic chromatography (MEKC). The buffers consisted of 90 mM borate set at pH 8.4 (CZE) and 20 mM phosphate and 50 mM sodium dodecyl sulfate set at pH 7.5 (MEKC). All analyses were carried out using fused silica capillaries at an electric field strength of 52.6 kV/m. The use of a reproducible identification parameter is very important in STA. To deal with the poor reproducibility of the migration time, we recently introduced the corrected effective mobility. In this study, we investigated the intra- and interinstrument reproducibility of the migration time, the effective mobility, and the corrected effective mobility. Large differences in intra-instrument reproducibility were found when the migration time was used. The calculation of the effective mobility and the corrected effective mobility diminished these differences and enhanced the interinstrument reproducibility roughly by a factor 3. For (corrected) effective mobilities, intrainstrument reproducibilities were between 0.8-2.6% and interinstrument reproducibilities were between 3.2-3.9%.     

Potential of Capillary Electrophoresis for the Profiling of Propolis

The usefulness of capillary electrophoresis (CE) with diode array detection for the profiling of Propolis, a hive product, is investigated. Water extracts of Propolis were analyzed with both capillary zone electrophoresis (CZE) at pH 7.0 and 9.3, and micellar electrokinetic chromatography (MEKC) with sodium dodecyl sulfate at pH 9.3. Characteristic profiles were obtained and several organic acids and preservatives could be identified by means of library comparison of the recorded UV spectra combined with addition of reference compounds to the extracts. The selectivity of the CZE and MEKC system differed considerably but the information obtained with both methods was similar. The dry residues of the water extraction were extracted with ethanol-water (70 : 30, v/v) and analyzed with the MEKC system to enable the separation of the more hydrophobic constituents of the Propolis samples. Complex profiles containing various well separated peaks were obtained allowing the identification of some interesting flavonoids. On the basis of the recorded CZE and MEKC profiles, the Propolis samples could be divided into two clearly different groups which are probably from a different origin.     

Determination of berberine and strychnine in medicinal plants and herbal preparations by pressurized liquid extraction with capillary zone electrophoresis.

A simple and rapid method for the determination of berberine and strychnine in medicinal plants and herbal preparations for regulatory purposes using a home-made pressurized liquid extraction (PLE) system with capillary zone electrophoresis (CZE) using ultraviolet detection at 254 nm was developed. The effects of pH, concentration of buffer, and organic modifiers in the electrophoretic separation were investigated. The buffer used for CZE contained 50 mM ammonium acetate, pH 3.1. The effect of temperature on the extraction efficiency of strychnine in medicinal plants by PLE was demonstrated. Comparable or higher extraction efficiency was achieved with PLE for strychnine in medicinal plants and berberine in herbal preparations compared to soxhlet extraction. The effect of matrix interference in medicinal plants and herbal preparations containing a number of medicinal plants samples using CZE was investigated by standard additional experiments. The reproducibility of the method using PLE with CZE was found to vary between 2.4 and 10.7% (n = 5/6) for different types of samples on different days.     

Quality evaluation of Guan‐Xin‐Ning injection based on fingerprint analysis and simultaneous separation and determination of seven bioactive constituents by capillary electrophoresis

The purpose of this study was to develop a comprehensive, rapid and practical capillary electrophoresis (CE) method for quality control (QC) of Guan‐Xin‐Ning (GXN) injection based on fingerprint analysis and simultaneous separation and determination of seven constituents. In fingerprint analysis, a capillary zone electrophoresis (CZE) method with a running buffer of 30 mM borate solution (pH 9.3) was established. Meanwhile, ten batches of samples were used to establish the fingerprint electropherogram and 34 common peaks were obtained within 20 min. The RSD of relative migration times (RMT) and relative peak areas (RPA) were less than 5%. In order to further evaluate the quality of GXN injection, a micellar electrokinetic chromatography (MEKC) method was developed for simultaneous separation and determination of bioactive constituents. Seven components reached baseline separation with a running buffer containing 35 mM SDS and 45 mM borate solution (pH 9.3). A good linearity was obtained with correlation coefficients from 0.9906 to 0.9997. The LOD and LOQ ranged from 0.12 to 1.50 μg/mL and from 0.40 to 4.90 μg/mL, respectively. The recoveries ranged between 99.0 and 104.4%. Therefore, it was concluded that the proposed method can be used for full‐scale quality analysis of GXN injection.     

The multi-concentration and two-dimensional capillary electrophoresis method for the analysis of drugs in urine samples

A novel method has been developed by integration of multi-concentration and two-dimensional(2D) capillary electrophoresis(CE) for simultaneous enhancement of detection sensitivity and separation power in complex samples.Capillary zone electrophoresis(CZE) was used as the first dimension separation according to mobilities,from which the effluent fractions were further analyzed by micellar electrokinetic capillary chromatography(MEKC) acting as the second dimension.Cation-selective exhaustive injection(CSEI) ...