Microwave processing of TiO2 blocking layers for dye-sensitized solar cells

The microwave heat treatment of blocking layers for dye-sensitized solar cells has been investigated. It has been found that the solar cell efficiencies achieved with microwave heating were considerably higher than those achieved with conventional heating at low temperatures (100°C). This was attributed to microwave heating providing better sintering of the blocking layer and better interfacial contact between the substrate and the TiO₂ layers. These results are promising with regard to the application of microwave heating to the production of dye-sensitized solar cells on flexible polymer substrates.     

Partially nanowire-structured TiO2 electrode for dye-sensitized solar cells

Partially nanowire-structured TiO₂ was prepared by a hydrothermal processing followed by calcination in air. The hydrogen titanate powder as-synthesized was calcined at 300 °C for 4 h to obtain the partially nanowire-structured TiO₂. A dye-sensitized solar cell (DSC) with a film thickness of 5.6 μm, fabricated using the partially nanowire-structured TiO₂ showed better performance than using a fully nanowire-structured TiO₂ or a conventional equi-axed TiO₂ nanopowder. The short-circuit current density (J_SC), the open-circuit voltage (V_OC), the fill factor (FF) and the overall efficiency (η) are 11.9 mA/cm², 0.754 V, 0.673 and 6.01 %, respectively. The effects of one-dimensional nanostructure and electron expressway concept are discussed.     

Anisotropic TiO2 nanomaterials in dye-sensitized solar cells

The review presented below summarizes the up-to-date research efforts in using one-dimensional TiO(2) nanomaterials in dye-sensitized solar cells. A brief account of the methods of synthesis of the anisotropic nanomaterials as well as their photovoltaic performance in DSCs was summarily presented. The usefulness of the materials as scattering layer in DSCs was also surveyed.     

TiO2/SnO2复合空心球在染料敏化太阳能电池中的应用

采用模板辅助法制备了SnO2/TiO2复合空心球,样品直径为1.5~4.0μm,比表面积达到了92.9 m^2·g^-1,复合空心球表现出优越的光散射性能.以这种复合空心球作为染料敏化太阳能电池的光阳极,电池的光电转换效率可达到7.72%,高于SnO2微米球(2.70%)和TiO2微米球(6.26%).此外,以锐钛矿型TiO2纳米晶作为底层,SnO2/TiO2复合空心球作为光散射层制备的双层结构光阳极,电池光电转换效率进一步提升至8.43%.     

Rutile TiO2 nano-branched arrays on FTO for dye-sensitized solar cells

Hierarchical TiO(2) nanostructures would be desirable for preparing dye-sensitized solar cells because of their large amount of dye adsorption and superior light harvesting efficiency, as well as efficient charge separation and transport properties. In this study, rutile TiO(2) nano-branched arrays grown directly on transparent conductive glass (FTO) were prepared by a facile two-step wet chemical synthesis process, using a simple aqueous chemical growth method involving immersing the TiO(2) nanorod arrays in an aqueous TiCl(4) solution as seeds, which were prepared by a hydrothermal method. The dye-sensitized solar cells based on the TiO(2) nano-branched arrays which were only about 3 μm in length show a short-circuit current intensity of 10.05 mA cm(-2) and a light-to-electricity conversion efficiency of 3.75%, which is nearly three times as high as that of bare nanorod arrays, due to the preferable nanostructure, which not only retains the efficient charge separation and transport properties of the nanorod arrays, but also can improve the amount of dye adsorption due to the increased specific surface area from the nanobranches.     

Hierarchical twin-scale inverse opal TiO2 electrodes for dye-sensitized solar cells

We describe the preparation of three-dimensional hierarchical twin-scale inverse opal (ts-IO) electrodes for dye-sensitized solar cells (DSSCs). The ts-IO TiO(2) structure was obtained from a template fabricated via the assembly of mesoscale colloidal particles (40-80 nm in diameter) in the confined geometry of a macroporous IO structure. The photovoltaic properties of ts-IO electrodes were optimized by varying the layer thickness or the size of mesopores in the mesoscale colloidal assembly. Electron transport was investigated using impedance spectroscopy. The result showed that due to the competing effects of recombination and dye adsorption, the maximum efficiency was observed at an electrode thickness of 12 μm. The electrodes of smaller mesopores diameters yielded the higher photocurrent density due to the decrease in the electron transport resistance at the TiO(2)/dye interface. A maximum efficiency of 6.90% was obtained using an electrode 12 μm thick and a mesopore diameter of 35 nm.     

Efficient dye-sensitized solar cells based on surfactant-mediated TiO2 nanostructures

Journal of Solid State Electrochemistry - Dye-sensitized solar cells (DSSCs) based on TiO2 nanostructures have attracted much attention due to their high photoconversion efficiency. Here, we report...     

Surface-treated TiO2 nanoparticles for dye-sensitized solar cells with remarkably enhanced performance

Dye-sensitized solar cells (DSSCs) were prepared by capitalizing on mesoporous P-25 TiO(2) nanoparticle film sensitized with N719 dyes. Subjecting TiO(2) nanoparticle films to TiCl(4) treatment, the device performance was improved. More importantly, O(2) plasma processing of TiO(2) film that was not previously TiCl(4)-treated resulted in a lower efficiency; by contrast, subsequent O(2) plasma exposure after TiCl(4) treatment markedly enhanced the power conversion efficiency, PCE, of DSSCs. Remarkably, with TiCl(4) and O(2) plasma treatments dye-sensitized TiO(2) nanoparticle solar cells produced with 21 μm thick TiO(2) film illuminated under 100 mW/cm(2) exhibited a PCE as high as 8.35%, twice of untreated cells of 3.86%.     

Addition of TiO2 nanowires in different polymorphs for dye-sensitized solar cells

TiO₂ (B) and TiO₂ anatase nanowires were prepared at 150 °C for 120 h by a hydrothermal method followed by calcination in air at 400 °C for 2 h and at 700 °C for 2 h for TiO₂ (B) and TiO₂ anatase, respectively. Although dye-sensitized solar cells (DSC) with fully nanowire electrodes showed a rather low light-to-electricity conversion efficiency of 1.33 % for TiO₂ (B) and 2.42% for TiO₂ anatase, 10 wt % nanowire-dispersed electrodes in a P-25 TiO₂-nanoparticle matrix demonstrated improved efficiency of 6.17 % for TiO₂ (B) and 6.53% for TiO₂ anatase, these exceeding that of pure P-25 electrodes in this work (η=5.59%). The dominant mechanisms of the improvement at 10 wt% for the two different polymorphs are thought to be different, i.e., a light-scattering and film-thickness increment for the TiO₂ (B) system, whereas there is an improved conduction path through the matrix for the TiO₂ anatase system.      

Facile synthesis of TiO2 inverse opal electrodes for dye-sensitized solar cells

Engineering of TiO(2) electrode layers is critical to guaranteeing the photoconversion efficiency of dye-sensitized solar cells (DSSCs). Recently, a novel approach has been introduced for producing TiO(2) electrodes using the inverted structures of colloidal crystals. This paper describes a facile route to producing ordered macroporous electrodes from colloidal crystal templates for DSSCs. Using concentrated colloids dispersed in a volatile medium, the colloidal crystal templates were obtained within a few minutes, and the thickness of the template was easily controlled by changing the quantity of colloidal solution deposited. Here, the effects of the structural properties of the inverse opal TiO(2) electrodes on the photovoltaic parameters of DSSCs were investigated. The photovoltaic parameters were measured as a function of pore ordering and electrode film thickness. Moreover, DSSC applications that used either liquid or viscous polymer electrolyte solutions were investigated to reveal the effects of pore size on performance of an inverse opal TiO(2) electrode.     

Bilayer inverse opal TiO2 electrodes for dye-sensitized solar cells via post-treatment

We investigated the formation of bilayer inverse opal TiO(2) (io-TiO(2)) structures via post-treatment with a TiO(2) precursor solution and characterized the photovoltaic performances of the resulting electrodes for use in dye-sensitized solar cells. The post-treatment of TiO(2) inverse opals in a precursor solution grew rutile TiO(2) nanoparticles on anatase crystalline phase io-TiO(2) surfaces, resulting in anatase/rutile bilayer structures. We achieved a maximum photovoltaic conversion efficiency of 4.6% using a 25 μm thick electrode formed with the post-treated io-TiO(2) under simulated AM 1.5 light. This efficiency represents a 183% improvement over the non-post-treated io-TiO(2) electrodes. The shell thickness was controlled by the post-treatment time. The effects of shell thickness on photovoltaic performance were investigated by measuring the morphologies and electrochemical impedance of the post-treated io-TiO(2). We found that post-treatment up to a certain period of time increased the surface area and electron lifetime, but further treatment resulted in decreased area and saturated lifetimes. The optimal post-treatment time was identified, and the optimal io-TiO(2) electrodes were characterized.     

Double-layer coating of SrCO3/TiO2 on nanoporous TiO2 for efficient dye-sensitized solar cells

Surface modification plays a crucial role in improving the efficiency of dye-sensitized solar cells (DSSCs), but the reported surface treatments are in general superior to the untreated TiO(2) but inferior to the typical TiCl(4)-treated TiO(2) in terms of solar cell performance. This work demonstrates a two-step treatment of the nanoporous titania surface with strontium acetate [Sr(OAc)(2)] and TiCl(4) in order, each step followed by sintering. An electronically insulating layer of SrCO(3) is formed on the TiO(2) surface via the Sr(OAc)(2) treatment and then a fresh TiO(2) layer is deposited on top of the SrCO(3) layer via the TiCl(4) treatment, corresponding to a double layer of Sr(OAc)(2)/TiO(2) coated on the TiO(2) surface. As compared to the typical TiCl(4)-treated DSSC, the Sr(OAc)(2)-TiCl(4) treated DSSC improves short-circuit photocurrent (J(sc)) by 17%, open-circuit photovoltage (V(oc)) by 2%, and power conversion efficiency by 20%. These results indicate that the Sr(OAc)(2)-TiCl(4) treatment is better than the often used TiCl(4) treatment for fabrication of efficient DSSCs. Charge density at open circuit and controlled intensity modulated photocurrent/photovoltage spectroscopy reveal that the two electrodes show almost same conduction band level but different electron diffusion coefficient and charge recombination rate constant. Owing to the blocking effect of the SrCO(3) layer on electron recombination with I(3)(-) ions, the charge recombination rate constant of the Sr(OAc)(2)-TiCl(4) treated DSSC is half that of the TiCl(4)-treated DSSC, accounting well for the difference of their V(oc). The improved J(sc) is also attributed to the middle SrCO(3) layer, which increases dye adsorption and may improve charge separation efficiency due to the blocking effect of SrCO(3) on charge recombination.     

Activation energy of electron transport in dye-sensitized TiO2 solar cells

Various characteristics of dye-sensitized nanostructured TiO2 solar cells, such as electron transport and electron lifetime, were studied in detail using monochromatic illumination conditions. The electron transport was found to be a thermally activated process with activation energies in the range of 0.10-0.15 eV for light intensities that varied 2 orders of magnitude. Electron lifetimes were determined using a new method and found to be significantly larger (>1 s) than previously determined. An average potential was determined for electrons in the nanostructured TiO2 under illumination in short-circuit conditions. This potential is about 0.2 V lower than the open-circuit potential at the same light intensity. The electron transport time varies exponentially with the internal potential at short-circuit conditions, indicating that the gradient in the electrochemical potential is the driving force for electron transport in the nanostructured TiO2 film. The applicability of the conventionally used trapping/detrapping model is critically analyzed. Although experimental results can be fitted using a trapping/detrapping model with an exponential distribution of traps, the distribution parameters differ significantly between different types of experiment. Furthermore, the experimental activation energies for electron transport are smaller than those expected in a trapping/detrapping model.     

Preparation of highly ordered TiO2 nanotubes on Ti-foil for dye-sensitized solar cells

TiO₂ nanotube arrays were grown on Ti foil in mixed electrolyte by the anodizing process. TiO₂ nanotube arrays were immersed in the TiCl₄ solution to improve the photocurrent by enhanced charge transfer between TiO₂ and dye molecules on the activity surface. Internal resistance of dye-sensitized solar cells (DSSC) was measured by impedance spectroscopy measurements. Backside illuminated DSSC with TiCl₄-treated TiO₂ nanotubes exhibited a conversion efficiency of 1.45% and showed improved electron transfer.     

One-pot easily-processed TiO2 macroporous photoanodes (Ti-HIPE) for dye-sensitized solar cells

1. Download : Download full-size image

     

Nb doping of TiO2 nanotubes for an enhanced efficiency of dye-sensitized solar cells

Nb-doped TiO(2) nanotube (with C(Nb) < 1 wt%) layers were successfully fabricated by self-ordered electrochemical anodization of Ti-Nb alloys. When used in dye-sensitized solar cells the efficiency enhanced by up to 30% compared to non-doped TiO(2) nanotubes. IMVS measurements indicate the beneficial effect to be due to lower recombination losses.     

静电喷雾法制备高效染料敏化太阳能电池的二氧化钛光阳极

TiO2光阳极膜是染料敏化太阳能电池（DSSC）的核心部件之一,它对电池的光电转换效率起决定性作用．TiO2电极一般采用刮涂法和丝网印刷法制备．近3年,通过静电喷雾制备光阳极的方法得到国内外学者的关注．静电喷雾制备光阳极会受到多种因素的影响,如电压、流速、悬浮液浓度、喷雾距离以及喷雾时间等．但这些因素对成膜和DSSC器件性能的影响却没有得到全面的研究或者报道．本文使用静电喷雾法制备了多孔TiO2纳米膜,并研究了以其为电极的电池器件特性．经过超声充分分散的稳定TiO2乙醇悬浮液在高电压下喷雾到导电玻璃上成膜．通过改变电喷雾距离,得到了具有不同形貌的TiO：光阳极膜,并解释了其形成的机理及其对电池性能的影响．研究还表明,光阳极膜的TiC14处理能够很好地改善电池性能．通过优化,基于流速为0．8mL／h、电喷雾距离和时间分别为2．2cm和8min条件下制备的光阳极,结合TiC14处理,组装的电池在模拟太阳光源AM1．5G下光电转化效率达6．24％．     

TiO2 derived by titanate route from electrospun nanostructures for high-performance dye-sensitized solar cells

We report the use of highly porous, dense, and anisotropic TiO(2) derived from electrospun TiO(2)-SiO(2) nanostructures through titanate route in dye-sensitized solar cells. The titanate-derived TiO(2) of high surface areas exhibited superior photovoltaic parameters (efficiency > 7%) in comparison to the respective electrospun TiO(2) nanomaterials and commercially available P-25.     

Low-temperature versus oxygen plasma treatment of water-based TiO2 paste for dye-sensitized solar cells

High-temperature treatment steps in fabrication process of dye sensitized solar cell (DSSC) significantly contribute to the manufacturing costs and limit the use of temperature sensitive substrates. Therefore our aim was to develop a simple method for the preparation of water-based TiO₂ paste. The paste is based on peroxotitanic acid (PTA) sol–gel matrix and commercial TiO₂ nanoparticles (P25). Two fabrication processes to decompose/transform the PTA matrix in the printed TiO₂ layer are explored and combined: annealing at temperatures up to 250 °C and/or oxygen plasma treatment. The results show that the PTA matrix in the paste converts to anatase phase and to some extent also attaches to the TiO₂ nanoparticles P25 acting as an interconnecting network within TiO₂ layer. The transformation of the PTA matrix occurs around 250 °C, but in the presence of TiO₂ nanoparticles P25 it starts already at 120 °C. In addition the results reveal that the crystallization is achievable also solely with the oxygen plasma treatment. The efficiency of the TiO₂ layers, exposed to different post-deposition treatments, is evaluated in DSSCs. The results show that oxygen plasma treatment of the TiO₂ layers could efficiently replace temperature curing at 250 °C. Within this study the DSSCs with the efficiency up to 4.2 % measured under standard test conditions (1,000 W/m², AM1.5, 25 °C) were realized.