β-环糊精聚合物-二茂铁安培型葡萄糖氧化酶电极

利用 β-环糊精的空穴结构 ,通过主客体化学反应将二茂铁包络在 β-环糊精聚合物的空穴中 ,同时将葡萄糖氧化酶交联在 β-环糊精聚合物上 ,制成对葡萄糖有灵敏响应的生物传感器。循环伏安和安培检测表明包络在 β-环糊精聚合物空穴中的二茂铁更加接近酶的氧化还原中心 ,可以有效地作为葡萄糖氧化酶和玻碳电极之间的电子媒介体 ,葡萄糖浓度在1.0×10-2 ～8.0mmol/L范围内 ,其浓度与电流响应值呈良好的线性关系 ,方法的检出限为2.0×10-3 mmol/L(S/N=3) ,在10s之内达到最大响应的95 %。用该法测定了血清中的葡萄糖含量 ,结果与传统方法吻合。     

蒙脱石-石墨-聚氯乙烯复合电极的研制

化学修饰电极自1975年正式问世以来^[1],经过多年的不断发展,现已出现了许多修饰方法^[2];如表面吸附法,聚合物薄膜法,共价键合法等。这些方法虽在一定程度上改善了修饰电极的表面结构,提高了电极的灵敏度和选择性,但由于此类修饰都是在电极表面附上一层修饰剂,容易因修饰层不牢而脱落,或修饰厚度不均匀而影响电极的性能,近年来出现了组合法制作碳糊电极^[3]及蒙脱石修饰碳糊电极^[4]的研究,但由于碳糊及其修饰电极存在电极表面柔软的缺点而使其生理性,稳定性欠佳,本文用聚氯乙烯作粘合剂,在其融状态下,将石墨和蒙脱石混合,加压,冷却制成复合电极,该复合电极用于苯酚测定时,表现出良好的稳定性,重现性和催化效果,并克服了蒙脱石修饰碳糊电极稳定性,重现性差的缺点。     

二茂铁修饰青椒籽碳糊电极测定抗坏血酸

以二茂铁作为电子传递介体,制成Ｆｅ修饰的青椒籽碳糊电极,研究了该电极的性能,用恒电位电流法测定了抗坏血酸的浓度并用于药物中抗坏血酸的含量分析,结果与药典法相符。     

自组装单层界面β-环糊精非电活性客体的电化学测定

提出了用电化学技术测定非电活性物质的新方法.利用合成的β-CD对甲苯磺酸基衍生物(Ts-β-CD)获得新型β-CD单层.虽然β-CD的覆盖率只有10%左右,但该单层对二茂铁表现出有效的主客体响应.界面上二茂铁的包络符合Langmuir吸附响应.利用Langmuir吸附等温式,得到二茂铁与β-环糊精形成包络物的包络常数为4.2×10~4mol-1·L二茂铁在该单层上的最大表面覆盖度为8.6×10~(-12)mol/cm2.当二茂铁溶液中含有非电活性物质间甲苯甲酸(mTA)或十二烷基磺酸钠(SDS)时,mTA和SDS与包络在电极表面的二茂铁发生客体竞争反应而使二茂铁的氧化还原峰电流降低.利用该原理,分别测定了非电活性物质mTA和SDS,线性范围分别为0.8~2.7μmol/L和5~100nmol/L.     

基于纳米MnO_2二茂铁修饰丝网印刷碳电极的尿酸生物传感器研究

在丝网印刷碳电极上修饰纳米MnO2,并利用戊二醛和β-环糊精交联固定尿酸酶,以二茂铁作为电子媒介体,研制用于测定尿酸浓度的生物传感器.实验结果表明,纳米MnO2降低了电子媒介体二茂铁的氧化还原反应电位,且纳米MnO2与电子媒介体二茂铁在尿酸生物传感器中表现出协同增效效应.该尿酸生物传感器线性响应范围是6.0×10-6～1.2×10-3 mol/L,检出限为3.0×10-6 mol/L.用纳米MnO2修饰酶电极,改善了电极表面条件,加快了电极反应速率,提高了尿酸传感器的灵敏度.     

β-环糊精与二茂铁包合物修饰碳糊电极上抗坏血酸的催化氧化波研究

二茂铁及其衍生物不能牢固吸附于电极表面, 特别是其氧化态(Fc+)溶于水, 影响了电极的稳定性[1].     

抗坏血酸在β-环糊精/二茂铁甲酸修饰电极上的电化学行为及测定

利用主客体化学反应将二茂铁甲酸包络在β-环糊精聚合物的空穴中,用新鲜蛋清作交联剂制成β-环糊精聚合物/二茂铁甲酸化学修饰玻碳电极,用电化学阻抗法和循环伏安法研究了修饰电极的电化学性能。在pH 7.0的磷酸盐缓冲溶液中,该修饰电极对抗坏血酸的电化学氧化有很好的催化活性,氧化峰电流与其浓度在6.2×10-6~5.0×10-3mol/L范围内呈良好的线性关系,线性回归方程为ip=0.4375+0.0301C(ip:μA,C:μmol/L),相关系数r=0.9982,检出限为1.0×10-6mol/L。抗坏血酸和多巴胺在修饰电极上于不同的电位(ΔE=490 mV)被氧化,可用于多巴胺存在下选择性测定抗坏血酸。     

多金属氧簇阴离子[Mo6O19]2-/PAMAM超分子化合物的制备、表征及性能

采用树状聚酰胺-胺(PAMAM)大分子化合物与同多酸阴离子[Mo6O19]2-,基于静电作用合成了同多金属氧酸盐/树型分子超分子化合物。用元素分析、FTIR、UV-V is、TG/DTA、荧光光谱等测试技术分别对样品进行了结构表征及性能测试。并利用其作为电极修饰剂,制得化学体修饰的碳糊电极(CMCPE),用循环伏安法研究了同多金属氧酸盐/树型分子超分子化合物修饰碳糊电极在1 mol/L H2SO4水溶液中的电化学行为。结果表明,该化合物具有良好的荧光性能和可逆光致变色性能;用该化合物修饰的碳糊电极与[Mo6O19][N(C4H9)2]2修饰的电极相比,在-0.2~0.2 V范围内多了1对氧化还原峰;当扫描速率低于100 mV/s时,该电极过程为表面控制过程,而当扫描速率高于100 mV/s时,电极过程变为扩散控制过程;且该电极在室温下具有很好的稳定性。     

水溶液中几种苯衍生物与β-环糊精包合物的热力学研究

β 环糊精 (β Ｃｙｃｌｏｄｅｘｔｒｉｎ ,β ＣＤ)是由 7个葡萄糖残基以α 1 ,4 糖苷键连接而成的环状化合物 ,具有疏水的空腔和亲水的外表面。这种特殊的结构使它可以作为宿主 (主体 )而依疏水作用力、范德华力或氢键包合多种客体分子形成包合物[1～ 3] ,并可增强客体分子对光、热、氧化等的稳定性[4,5] 。有机物质与 β ＣＤ形成包合物后通常会发生光谱等特征的变化 ,因此可用光谱等方法研究包合物的稳定常数[4] ,并进而获得水溶液中包合体系的热力学参数[6 ] 。本文采用紫外分光光度法 ,研究水溶液中几种苯衍生物与β ＣＤ包合物的稳定…     

5,11,17,23-四叔丁基-25,26,27,28-四[3-(甲氧基羰基)苄氧基]杯[4]芳烃包合性能的研究

杯芳烃是继冠醚和环糊精后的第三代主体化合物 .这类主体分子不仅可以识别和络合阳离子 ,而且还具有包合中性有机分子的性能 [1～ 5] .杯 [4]芳烃类包合物的晶体结构测定表明 ,它们可分为分子内和分子间包合两种类型 [3 ,5] ,前者是客体分子被包合在主体分子的空穴内 ,后者是客体分子被包合在主体分子之间 .对叔丁基杯 [4]芳烃的下沿酚氧基与上沿均可进行化学修饰得到不同的杯 [4]芳烃衍生物 .最早报道的对叔丁基杯 [4]芳烃及其衍生物的分子内包合物是与甲苯或乙腈的 1∶ 1包合物 [4 ,5] ,客体分子依靠 CH3 -π的作用被包结在主体分子内[6]…     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Selective syntheses of 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones via temperature-dependent Rh(II)-carbenoid-mediated 2H-azirine-ring expansion

The Rh(II)-catalyzed reaction of 2-carbonyl-substituted 2H-azirines with ethyl 2-cyano-2-diazoacetate or 2-diazo-3,3,3-trifluoropropionate provides an easy access to 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones. These compounds can be selectively prepared from the same starting material using temperature as the only varied parameter. The 2-azabuta-1,3-diene intermediate, a common precursor for both heterocyclic products, isomerizes into 2H-1,3-oxazine under kinetic control, while 1H-pyrrol-3(2H)-one is the sole product of the reaction at elevated temperatures. According to DFT-calculations a one-atom oxazine ring contraction involving ring-opening to a 2-azabuta-1,3-diene intermediate, followed by a 1,5- and 1,2-prototropic shift leads to the consecutive formation of imidoylketene and azomethine ylide, which then further undergo cyclization to the pyrrole derivative.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.