Ionic and electronic conductivities,stability and thermal expansion of La10 − x(Si,Al)6O26 ± δ solid electrolytes

Apatite-type La_10 − xSi_6 − yAl_yO_{27 − 3x/2 − y/2} (x = 0–0.33; y = 0.5–1.5) exhibit predominant oxygen ionic conductivity in a wide range of oxygen partial pressures. The conductivity of silicates containing 26.50–26.75 oxygen atoms per formula unit is comparable to that of gadolinia-doped ceria at 770–870 K. The average thermal expansion coefficients are (8.7–10.8) × 10^− 6 K^− 1 at 373–1273 K. At temperatures above 1100 K, silicon oxide volatilization from the surface layers of apatite ceramics and a moderate degradation of the ionic transport with time are observed under reducing conditions, thus limiting the operation temperature of Si-containing solid electrolytes.     

A co-doping approach towards enhanced ionic conductivity in fluorite-based electrolytes

A co-dopant strategy is used to investigate the effect that the elastic strain in the lattice has on the grain ionic conductivity of doped ceria electrolytes. Based on critical dopant ionic radius (r_c), different compositions in the Lu_xNd_yCe_1−x−yO_2−δ (x + y = 0.05, 0.10, 0.15, and 0.20) system are studied. Dopants are added such that the weighted average dopant ionic radius matches r_c for all the compositions. Dense ceramic discs are prepared using conventional solid oxide route and sintering methods. Precise lattice parameter measurements are used to calculate the lattice strain. The ionic conductivity of the samples is measured in the temperature range of 250 °C to 700 °C using two-probe electrochemical impedance spectroscopy technique. The elastic strain present in Lu_xNd_yCe_1−x−yO_2−δ system is found to be negligible when compared to Lu_xCe_1−xO_2−δ (negative) and Nd_xCe_1−xO_2−δ (positive) systems. Grain ionic conductivity of Lu_xNd_yCe_1−x−yO_2−δ (where x + y = 0.05) at 500 °C is observed to be 1.9 × 10^− 3 S/cm which is twice as high as that of Lu_0.05Ce_0.95O_2−δ. These results extend the validity of the r_c concept as a strategy for co-doping ceria electrolytes and open new designing avenues for solid oxide electrolytes with enhanced ionic conductivity.     

Effect of Ge4+ and Mg2+ doping on superconductivity,fluctuation induced conductivity and interplanar coupling of TlSr2CaCu2O7−δ superconductors

Substitution of Ge⁴⁺ in place of Cu in Tl_0.85Cr_0.15Sr₂CaCu_2?xGe_xO_7?δ (x = 0–0.6) showed initial increase in zero critical temperature value, T_{c zero} from 98 K (x = 0) to 100 K (x = 0.1) and in the range of 85–86 K for x = 0.2–0.3. The slow decrease in T_{c zero} is unexpected as tetravalent Ge⁴⁺ substitution is expected to strongly reduce hole concentration in the samples and suppress T_{c zero}. Excess conductivity analyses of resistance versus temperature data based on Asmalazov–Larkin (AL) theory revealed that the substitution induced 2D-to-3D transition of fluctuation induced conductivity with the highest transition temperature, T_2D–3D observed at x = 0.1. FTIR spectroscopy analysis indicates Ge⁴⁺ substitution cause reduction in CuO₂/GeO₂ interplanar distance while our calculation based on Lawrence–Doniach model revealed highest superconducting coherence length, ξ_c(0) and interplanar coupling, J at x = 0.3. On the other hand, substitution of divalent Mg²⁺ for Ca²⁺ in (Tl_0.5Pb_0.5)(Sr_1.8Yb_0.2)(Ca_1?yMg_y)Cu₂O₇ (y = 0–1.0), which is not expected to directly vary hole concentration, surprisingly caused T_{c zero} to increase from 89.6 K (y = 0) to an optimum value of 95.9 K (y = 0.6) before decreasing with further increase in y. Excess conductivity analyses showed 2D-to-3D transition of fluctuation induced conductivity for all samples where the highest T_2D–3D was at y = 0.4. Similar calculation revealed highest values of ξ_c(0) and J also at y = 0.4. FTIR analysis of the samples indicates inequivalent Cu(1)O(2)Pb/Tl lengths and possible tilting of CuO₂ plane as a result of Mg²⁺ substitution. The increased ξ_c(0) and J as a result of the Ge⁴⁺ and Mg²⁺ substitutions are suggested to contributed to sustenance of superconductivity above 80 K in the samples.     

Oxygen-rich Ti1−xO2 pillar growth at a gold nanoparticle–TiO2 contact by O2 exposure

In-situ gas-injection transmission electron microscopy revealed that a pillar grew at the edge of the interface of a gold nanoparticle and a TiO₂ substrate during exposure to O₂ gas at 100 Pa. The pillar was found to have a titanium-deficient chemical composition of Ti_1 ? xO₂ (x > 0) by electron energy loss spectroscopy (EELS). The spectra showed a chemical shift of oxygen and titanium ions to have ionic states of Ti³⁺ and O^y? (y < 3/2). The formation of the Ti_1 ? xO₂ at the contact edge of gold–Ti_1 ? xO₂ interface is discussed from the perspective of an O₂ affinity, which plays an important role in CO oxidation process of supported gold particle.     

Influence of Sr substitution on thermoelectric properties of La1−xSrxFeO3 ceramics

Perovskite La_1−xSr_xFeO₃ (0.10 ⩽ x ⩽ 0.20) ceramics have been synthesized by the conventional solid-state reaction technique. Their electrical resistivity, Seebeck coefficient and thermal conductivity have been measured. It has been found that the increase of Sr content reduces significantly both the electrical resistivity and the Seebeck coefficient, but slightly increases the high-temperature thermal conductivity. An adiabatic hopping conduction mechanism of small polaron is suggested from the analysis of the temperature dependence of the electrical resistivity. Seebeck coefficients decrease with increasing temperature, and saturate at temperature above 573 K. The saturated value of Seebeck coefficient decreases with increasing of Sr contents, from 200 μV/K for x = 0.10 to 100 μV/K for x = 0.20. All samples exhibit lower thermal conductivity with values around 2.6 W/m K. The highest dimensionless figure of merit is 0.031 at temperature 973 K in La_0.88Sr_0.12FeO₃.     

Electronic property and structure of double-doping Y1−2xPrxCaxBa2Cu3O7−δ with 0 ⩽ x ⩽ 0.14

Equal amount Pr and Ca double-doping Y_1?2xPr_xCa_xBa₂Cu₃O_7?δ with 0 ? x ? 0.14 have been investigated by X-ray diffraction, resistivity, and X-ray photoemission spectroscopy (XPS). The deviation of the linearly decreasing of T_c vs. x curve was observed when x < 0.10. The resistivity and the temperature coefficient of resistivity also exhibit abnormal behaviors around x = 0.10. It is revealed that the conductivity behavior of Y_1?2xPr_xCa_xBa₂Cu₃O_7?δ with low Pr content (x < 0.10) is different from that of the relative high Pr content (x > 0.10), which suggests a change of Pr valence with the Pr content. XPS measurement shows that the relative amount of Pr³⁺ and Pr⁴⁺ is closely related to the total Pr content x. The valence of Pr is close to +3 when x < 0.10 and increases towards +4 when x > 0.10, which implies a different mechanism for depression of superconductivity of Pr content x < 0.10 from that of Pr content x > 0.10 in Pr doping Y-123.     

The interfacial effect on ionic conduction of AgI–anatase TiO2 composites

AgI–anatase TiO₂ nanoparticle composites, (x)AgI–(1 ? x)anatase, with different porosities were fabricated over a wide range of 0–1 of AgI content. The electrical conductivity was measured at room temperature as function of AgI content (x) and porosity (p). The conductivity varies considerably with both x and p. In the vicinity of x = 0.4 and p = 0.31, the conductivity attains a maximum (2.5 × 10^? 3 S/cm). The conductivity is enhanced by three orders of magnitude in comparison with that of pristine AgI. The mechanism of the observed conductivity enhancement is discussed in the light of the scanning electron microscope images and X-ray diffraction patterns of the different (x)AgI–(1 ? x)anatase composites.     

Electrical and mechanical properties of diluted magnetic semiconductor Zn1−xMnxS nanocrystalline films

Nanostructured Zn_1−xMn_xS films (0 ⩽ x ⩽ 0.25) were deposited on glass substrates by simple resistive thermal evaporation technique. All the films were deposited at 300 K in a vacuum of 2 × 10⁻⁶ m bar. All the films temperature dependence of resistivity revealed semiconducting behaviour of the samples. Hot probe test revealed that all the samples exhibited n-type conductivity. The nanohardness of the films ranges from 4.7 to 9.9 GPa, Young’s modulus value ranging 69.7–94.2 GPa.     

Electrical conductivity of (Ba0.3Sr0.2La0.5)(In1−xFex)O3−δ

We have synthesized the perovskite oxides of the (Ba_0.3Sr_0.2La_0.5)(In_1−xFe_x)O_3−δ system and measured the total electrical conductivity as a function of temperature and oxygen partial pressure. It was found that the single-phase composition region extended from x = 0.0 to x = 1.0, and that the Fe valence increased from 3.06 to 3.50 in that region. The electrical conductivity was semiconducting from x = 0.0 to x = 0.40 and metallic from x = 0.50 to x = 1.0. The total electrical conductivity at 800 °C also increased with the Fe content and achieved a maximum value of 140 (S/cm) at x = 1.0. From the dependence of the electrical conductivity on the oxygen partial pressure, we conclude that above x = 0.50, the majority carriers are holes. The estimated hole conductivity increased exponentially with the amount of Fe⁴⁺ cation present. The oxide ion conductivity was dependent on the oxygen vacancy content.     

Synthesis and electrical properties of nanocrystalline Ca1 − xEuxMnO3 ± δ (0.1 ≤ x ≤ 0.4) powders prepared at low temperature using citrate gel method

Nanopowders of Ca_1 − xEu_xMnO₃ (0.1 ≤ x ≤ 0.4) manganites were synthesized as a single phase using the auto gel-combustion method. The citrate method shows to be simple and appropriate to obtain single phases avoiding segregation or contamination. The Ca_1 − xEu_xMnO₃ system has been synthesized at 800 °C during 18 h, against the conventional method of mixing oxides used to obtain these materials at higher temperatures of synthesis. The formation reaction was monitored by X-ray diffraction (XRD) analysis and an infrared absorption technique (FTIR). The polycrystalline powders are characterised by nanometric particle size, ∼ 48 nm as determined from X-ray line broadening analysis using the Scherrer equation. Morphological analysis of the powders, using the scanning electron microscope (SEM), revealed that all phases are homogeneous and the europium-substituted samples exhibit a significant decrease in the grain size when compared with the undoped samples. The structure refinement by using the Rietveld method indicates that the partial calcium substitution by europium (for x ≥ 0.3) modifies the orthorhombic structure of the CaMnO₃ perovskite towards a monoclinic phase. All manganites show two active IR vibrational modes around 400 and 600 cm^− 1. The high temperature dependence of electrical resistivity (between 25 and 600 °C) allows us to conclude that all the samples exhibit a semiconductor behaviour and the europium causes a decrease in the electrical resistivity by more than one order of magnitude. The results can be well attributed to the Mn⁴⁺/Mn³⁺ ratio.     

Synthesis and electrical transport properties of Lu2+xTi2−xO7−x/2 oxide-ion conductors

The Lu_2+xTi_2−xO_7−x/2 (x = 0; 0.052; 0.096; 0.286; 0.44; 0.63; 33.3–49 mol% Lu₂O₃) nanoceramics with partly disordered pyrochlore-type structure are prepared by sintering freeze-dried powders obtained by a co-precipitation technique with 1600 °C annealing. Similar to pyrochlore-like compositions in the zirconate system, some of the new titanates are good oxide-ion conductors in air. The new solid-state electrolytes have oxide-ion conductivity in the interval of 1.0 × 10^− 3 – 2.5 × 10^− 3 S/cm at 740 °C in air. This value of conductivity is comparable with that of ZrO₂/Y₂O₃ ceramics. The conductivity of Lu_2+xTi_2−xO_7−x/2 depends on the chemical composition. The highest ionic conductivity is exhibited by nearly stoichiometric Lu_2+xTi_2−xO_7−x/2 (x = 0.096; 35.5 mol% Lu₂O₃) material containing ∼ 4.8 at.% Lu_Ti anti-site defects.     

Ion and electron conduction in SrFe1−xScxO3−δ

The oxygen ion and electron transport in SrFe_1−xSc_xO_3−δ  (x = 0.1–0.3) system at 700–950 °C were studied analyzing the total conductivity dependencies on the oxygen partial pressure, pO₂. The conductivity measurements were performed both under reducing conditions (10^− 19 ≤ pO₂ ≤ 10^− 8 atm) comprising the electron-hole equilibrium point, and in oxidizing atmospheres (10^− 5 ≤ pO₂ ≤ 0.5 atm) which are characterized by extensive variations of the oxygen content studied by coulometric titration technique. The incorporation of 10% Sc³⁺ cations into the iron sublattice suppresses transition of the cubic perovskite phase into vacancy-ordered brownmillerite, thus improving ion conduction at temperatures below 850 °C. When scandium content increases, the ion conductivity becomes considerably lower. The hole mobility is thermally-activated and varies in the range of 0.001 to 0.05 cm² V^− 1 s^− 1, increasing with oxygen concentration and decreasing on Sc doping.     

Modification of B-site doping of perovskite LaxSr1 − xFe1 − y−zCoyCrzO3 − δ oxide by Mg2+ ion

Co-doping B-site of perovskite oxide La_xSr_1 ? xCo_yFe_1 ? yO_3 ? δ (LSCFO) with Cr⁶⁺ and Mg²⁺ ions has been attempted in this research for revamping chemical stability and oxygen ionic conductivity of this mixed conducting oxide. It is known that partial substitution for B-site cations of LSCFO by Cr gives rise to a significant improvement on chemical and thermal stability of the perovskite oxide. On the basis of this doped structure, introduction of an immaterial dose of Mg²⁺ ion into its B-site results in a microstructure consisting of smaller grains with higher density than its precursor. Furthermore, the resulting perovskite oxide La_0.19Sr_0.8Fe_0.69Co_0.1Cr_0.2 Mg_0.01O_3 ? δ (LSFCCMO) displays higher O^2? conductivity than the solely Cr-doped LSCFO besides the improved chemical stability against reduction in 5% CH₄/He stream at 850 °C. A detailed examination of the oxidation states of B-site transition metal ions by XPS has also been conducted as a part of structural characterizations of LSFCCMO. The assessment of relative O^2? conductivity shows that the grain boundary area plays a more important role than the bulk phase in facilitating ion transport, but with comparable boundary areas the higher densification level is favorable.     

Noise behavior of amorphous GexSi1−xOy for microbolometer applications

High resistivity sputtered a-Ge_xSi_1−xO_y compound was investigated for application to microbolometer fabrication for thermal imaging. Noise behavior of the fabricated bolometers was measured, showing no evidence of random telegraph switching (RTS) noise. 1/f noise was measured at several measuring currents, resulting in a 1/f noise factor of 2.9 × 10⁻¹¹ that can be used for further design and modeling.     

The effect of dispersed SrTiO3 particles on the ionic conduction of (La,Li)Ti2O6

Ionic conductivity of La_4/3 ? y Li_3yTi₂O₆ (LLTO), where y value is 0.21, dispersed by various amount of strontium titanate (SrTiO₃) was measured by complex impedance method, and powder X-ray diffraction (XRD) measurements and scanning electron microscope (SEM) observations were carried out. With increasing SrTiO₃ concentration, the conductivity decreased. At 34 mol%, the Bragg peaks at 11, 26 and 35° in LLTO disappeared in XRD patterns and small non-angulated crystals were shown in SEM. The behavior of ionic conductivity was discussed by using the effective medium approximation (EMA) theory.     

Preparation,characterization and electrical property of Mn-doped ceria-based oxides

Manganese-doped ceria-based oxides, Ce_1−xMn_xO_2−δ (0.05 ≤ x ≤ 0.3) and Ce_1−x−yGd_xMn_yO_2−δ˙ (0.05 ≤ x≤ 0.2, 0.05 ≤ y ≤ 0.25) were synthesized, and crystal phase analysis by XRD and measurements of electrical properties were performed. Solubility limit of Mn in Ce_1−xMn_xO_2−δ˙ seemed to be between 5 mol% and 10 mol% and Mn₃O₄ was the main by-product above the solubility limit in the case of heat treatment at 1300 °C. Judging from the oxygen partial pressure dependence of total conductivity and emf measurements, Ce_1−xMn_xO_2−δ˙ is a single-phase mixed conductor within the composition below the solubility limit, and when the composition of Mn exceeds the solubility limit, it becomes the dual-phase mixed conductor of Ce_1−xMn_xO_2−δ˙ and Mn₃O₄. The doing of Mn in gadlia-doped ceria, Ce_1−x−yGd_xMn_yO_2−δ˙ (0.05 ≤ x ≤ 0.2, 0.05 ≤ y ≤ 0.25), was more difficult than that in CeO₂ presumably due to the preferential reaction between Gd and Mn to give GdMnO₃ to the GDC solid solution formation, and the Mn doping seems not to be so effective in preparing the mixed ionic–electronic conductor based on GDC.     

Synthesis and characterization of layered Li1−x(Ni0.5Co0.5)1−yFeyO2(0 ≤ (1 − x) ≤ 1 and 0 ≤ y ≤ 0.2) cathodes

Layered Li(Ni_0.5Co_0.5)_1−yFe_yO₂ cathodes with 0 ≤ y ≤ 0.2 have been synthesized by firing the coprecipitated hydroxides of the transition metals and lithium hydroxide at 700 °C and characterized as cathode materials for lithium ion batteries to various cutoff charge voltages (up to 4.5 V). While the y = 0.05 sample shows an improvement in capacity, cyclability, and rate capability, those with y = 0.1 and 0.2 exhibit a decline in electrochemical performance compared to the y = 0 sample. Structural characterization of the chemically delithiated Li_1−x(Ni_0.5Co_0.5)_1−yFe_yO₂ samples indicates that the initial O3 structure is maintained down to a lithium content (1 − x) ≈ 0.3. For (1 − x) < 0.3, while a P3 type phase is formed for the y = 0 sample, an O1 type phase is formed for the y = 0.05, 0.1 and 0.2 samples. Monitoring the average oxidation state of the transition metal ions with lithium contents (1 − x) reveals that the system is chemically more stable down to a lower lithium content (1 − x) ≈ 0.3 compared to the Li_1−xCoO₂ system. The improved structural and chemical stabilities appear to lead to better cyclability to higher cutoff charge voltages compared to that found before with the LiCoO₂ system.     

Oxygen non-stoichiometry and electrical conductivity of Pr2−xSrxNiO4±δ with x = 0–0.5

Oxygen non-stoichiometry and electrical conductivity of the Pr_2−xSr_xNiO_4±δ series with x = 0.0–0.5 were investigated in Ar/O₂ (pO₂ = 2.5 to 21 000 Pa) within a temperature range of 20–1000 °C. The equilibrium values of oxygen non-stoichiometry and electrical conductivity of these nickelates were determined as functions of temperature and oxygen partial pressure (pO₂). The nickelates with x = 0–0.5 appear to be p-type semiconductors in the investigated temperature and pO₂ ranges. The nickelates with x = 0.3–0.5 show very feebly marked pO₂ dependencies of the conductivity. Pr_1.7Sr_0.3NiO_4±δ shows the anomalies of the conductivity versus oxygen partial pressure which can be related to the orthorhombic–tetragonal crystal structure transformations. The conductivity of the Pr_2−xSr_xNiO_4±δ samples correlates with the average oxidation state of the nickel cations. The samples with x = 0.5 have the highest nickel oxidation state (≈ 2.5+), the highest [Ni³⁺]/[Ni²⁺] ratio close to 1 and show the highest conductivity (≈ 120 S/cm) in the whole pO₂ and temperature ranges investigated.     

Ionic conductivities of Nasicon-type glass-ceramic superionic conductors in the system Na2O–Y2O3–XO2–SiO2 (X = Ti,Ge, Te)

Glass-ceramics of the titanium-, germanium- or tellurium-containing Na₅RSi₄O₁₂-type (R = rare earth; Y) Na⁺-superionic conductors (N5YXS) were prepared by crystallization of glasses with the composition Na_3+3xY_1 ? xX_ySi_3 ? yO₉ (X = Ti; NYTiS, Ge; NYGeS, X = Te; NYTeS), and the effects of X elements on the separation of the phase and the microstructural effects on the conduction properties of glass-ceramics were discussed. The combination of x and y was most varied in N5YGeS and more limited in the order of N5YTeS > N5YTiS. Their conductivities and activation energies are of the order of 10^? 2 S/cm at 300 °C and of 15 to 24 kJ/mol, respectively. The conductivity of the glass-ceramic N5YXS decreases giving the order N5YGeS > N5YTeS > N5YTiS. It is considered that this order corresponds to the N5 single phase region. Large enhancement of electrical conductivity was observed in the glass-ceramics as the grain growth was promoted with increase of heating temperature and heating time for crystallization.     

A study on the Raman spectra of Al-doped and Ga-doped ZnO ceramics

Al_xZn_1−xO and Ga_yZn_1−yO ceramics were synthesized through a solid-state reaction technique. The crystal phase of the samples was identified by an X-ray diffraction experiment. For each sample, the electrical resistivity was determined. The Al 2-mol%-doped and Ga 0.5-mol%-doped ZnO ceramics had the lowest resistivity. Raman measurement was performed to study the doping effects in the ZnO ceramics including ZnO single crystal as a reference. The line-shape parameters, q₁ and Γ₁, at the same certain doping rate and the solubility limit of Al (2 mol%) and Ga (0.5 mol%) in ZnO ceramics, are strongly related to the each other, and that the solubility limit plays an important role. The second-order Raman peak at 1162 cm⁻¹ of the ZnO ceramics was fitted by Fano formalism. The Fano’s fitting parameters, such as the lifetime of phonon and the degree of asymmetry degree of the second-order Raman peak changed as the amounts of dopants were varied.