两亲接枝共聚物PS-g-N-PEO的合成及表面性能研究——铸膜溶剂及浓度的影响

采用大分子单体法合成了一系列聚苯乙烯接枝壬基酚聚氧乙烯 (PS g NPEO)两亲共聚物 ,采用溶液铸膜法将其在PET表面制膜 ,并利用扫描电子显微镜 (SEM) ,X射线光电子能谱 (XPS) ,衰减全反射红外光谱(ATR)和水接触角 (CA)等手段研究了共聚物组成、铸膜溶剂及浓度对共聚物膜表面形貌、组成及水浸润性能的影响 .结果表明 ,两亲接枝共聚物在不同条件下可形成规则的表面微孔 ,共聚物中NPEO含量越高 ,共聚物膜表面微孔孔径越大 ,对应的水接触角越小 .以THF为铸膜溶剂时 ,制膜浓度越大 ,共聚物膜表面微孔孔径越大 ,对应的水接触角越小 ;而以甲苯为溶剂时 ,制膜浓度对共聚物膜表面形貌影响不大 ,但水接触角要较THF体系显著降低 ,水接触角与浓度关系与THF体系相反 ,制膜浓度越大 ,对应的水接触角越大 .制膜浓度相同时 ,THF作溶剂 ,共聚物膜微孔较大 ,表面亲水组分含量较低 ;以甲苯为溶剂 ,微孔较密 ,表面亲水组分较高 .     

胶体颗粒在聚电解质多层膜表面的可控组装

利用原子力显微镜和扫描电子显微镜研究了磺化聚苯乙烯胶体颗粒在由聚二甲基二烯丙基氯化铵和聚苯乙烯磺酸钠层状自组装而成的多层膜表面的组装.该组装受表面性质影响,通过对多层膜的最外层的组装条件或利用盐溶液对多层膜进行后处理可以控制胶体颗粒在膜表面的组装密度.     

基于相转化全过程的聚合物微孔膜功能化研究进展

传统的相转化过程主要通过相分离的热力学及动力学因素对聚合物膜的微孔结构进行调控,该过程是一个典型的物理过程,不涉及膜的表/界面功能调控。微孔膜的表/界面功能如抗污染性能、抗菌性能和抗凝血性能等对于分离性能具有重要影响。本文提出了基于相转化全过程赋予聚合物微孔膜表/界面特定化学功能的方法,即"化学相转化",其本质是围绕相转化全过程控制功能分子在膜及微孔表面的迁移路径及固定方式,实现了膜的表/界面功能化。总结了通过"化学相转化"进行聚合物微孔膜的表/界面功能化策略,根据功能分子迁移路径可分为:基于铸膜液的由内而外(Inside-out)迁移及原位交联功能化策略、基于凝固浴的由外而内(Outside-in)迁移及离域交联功能化策略、基于微孔膜的自上而下(Top-down)迁移及界面交联功能化策略,从而实现了聚合物微孔膜的表/界面功能化改性及其在水处理、油水分离和血液净化等方面的应用。"化学相转化"理论为高性能、多功能聚合物微孔膜的制备及其分离应用提供了新的研究思路。功能分子的引入也会对相转化过程产生影响,从而影响膜的微孔结构,本课题组将从微孔结构调控和表/界面功能化这两个方面完善"化学相转化"理论。     

DOPA在聚乙烯微孔膜上的自聚合及肝素固定化

在溶液条件下,左旋3,4-二羟基苯丙氨酸(L-DOPA,或L-多巴)能在固体材料表面自发聚合,形成强力附着于材料表面的poly(DOPA)层.基于L-DOPA的这一特性,对聚乙烯(PE)微孔膜进行了表面改性,得到了PE/poly(DOPA)复合膜,并进一步通过poly(DOPA)层上的反应性基团将肝素共价固载在PE微孔膜上.X光电子能谱(XPS)分析结果证实了poly(DOPA)和肝素的固定,接触角测量数据表明膜的亲水性得到了显著提高.     

聚苯乙烯树脂固载聚乙二醇及吡啶weng盐的合成及其活性评价

以氯甲基化聚苯乙烯为原料，先后接枝聚乙二醇及吡啶，合成了双中心固载相转移催化剂──交联聚苯乙烯固载聚乙二醇４００及吡啶weng盐，并对氯甲基化聚苯乙烯树脂、聚苯乙烯固载聚乙二醇树脂、聚苯乙烯固载吡啶weng盐树脂及双中心树脂进行了红外光谱测试和分析，通过醋酸钾与溴节的反应，对各催化剂进行了活性评价，发现固载双中心相转移催化剂的活性明显高于各单中心固载相转移催化剂。     

利用层层自组装技术制备聚电解质多层膜高效液相色谱固定相

以聚(乙烯-alt-马来酸)的苯乙胺衍生物与聚烯丙基胺盐酸盐为原料,通过层层自组装技术(LBL)在色谱硅胶表面交替沉积得到聚电解质多层膜高效液相色谱(HPLC)固定相;利用紫外光谱、红外光谱和元素分析研究了HPLC固定相的结构和组成.结果表明,聚电解质多层膜HPLC固定相被成功构筑在硅胶颗粒表面;制备的多层膜固定相可方便地用于6种芳香烃类及4种烷基苯类物质的分离分析.本文的研究结果说明LBL技术在制备HPLC固定相方面具有一定的应用价值.     

聚苯乙烯树脂固载聚乙二醇及吡啶翁盐的合成及其活性评价

以氯甲基化聚苯乙烯为原料，先后接枝聚乙二醇及吡啶，合成了双中心固载相转移催化剂－交联聚苯乙烯固载聚乙二醇400及吡啶翁盐，并对氯甲基化聚苯乙烯树脂、聚苯乙烯固载聚乙二醇树脂、聚苯乙烯固载吡啶翁盐树脂及双中心树脂进行了红外光谱测试和分析。通过醋酸钾与溴苄的反应，对各催化剂进行了活性评价。发现固载双中心相转移催化剂的活性明显高于各单向中心固载相转移催化剂。     

表面微图案化聚乳酸膜的制备及其细胞亲和性评价

利用溶剂-非溶剂法(SNS)制备表面具有微孔图案的聚乳酸(PLA)膜和聚苯乙烯(PS)膜,并以微孔PS膜为模板,构建表面具有微岛图案的PLA膜.以此为基础,对所制备的微图案表面对PLA膜亲/疏水性及成骨细胞粘附与增殖性能的影响进行研究.结果显示微图案的存在显著增强了PLA膜的表面疏水性(水接触角90°);成骨细胞在微图案表面具有良好的铺展性,其黏附数量明显高于光滑PLA膜,但细胞的生长曲线相对较平缓,显示微图案表面虽有利于细胞在PLA膜表面的粘附与铺展,但对促进细胞的增殖无贡献.     

板式磁颗粒化学发光免疫分析在癌胚抗原测定中的应用

开发了一种板式磁颗粒化学发光免疫分析方法并将其用于人血清中癌胚抗原(CEA)的测定,该方法利用HRP标记的CEA抗体以及FITC标记的CEA抗体与CEA抗原在微孔板中进行夹心反应,使用抗FITC抗体包被的磁性微粒子溶液作为分离固相,利用了一个特殊的适用于微孔板的磁性分离器进行分离,最后加入鲁米诺和H2O2底物进行发光反应.该方法采用微孔板代替透明管作为反应容器,磁颗粒作为分离固相在微孔里与免疫试剂反应,提前用BSA将微孔板封闭,很好地解决了管式磁颗粒方法非特异吸附高以及包被板方法线性范围小的局限性,同时避免了管间差异以及包被不均问题.该方法结合了微孔板作为反应容器以及磁颗粒分离体系的优点,使用夹心法对人血清中的CEA在0～250ng/mL浓度范围进行了测定,检测灵敏度为0.57ng/mL,批内和批间变异分别小于7%和11%.与市售CLIA试剂盒测定结果做了比对,两者显示了很好的相关性.该法经济、优越,有望实现商品化.     

电压对含锌电解液微弧氧化TiO2膜结构和性能的影响

以纯钛(TA4)为原料,用含乙酸锌电解液制备微弧氧化(MAO)TiO₂膜,探究不同电压对膜的表面结构、亲水性、耐腐蚀性和抗菌性能的影响。结果表明,MAO处理后,涂层表现出多孔结构,主要由Ti相、锐钛矿和金红石TiO₂相组成。随着电压的升高,膜层中金红石TiO₂相增加,膜层上的微孔平均直径增加,孔隙率减小。所有膜层表现出良好的亲水性,与纯钛板相比,所有膜层均具有良好的抗菌性能,其中400 V条件下形成的MAO涂层的抗菌性能最好,达到91%,并且其耐腐蚀性最强。综上所述,当MAO电压为400 V时,制备的膜层综合性能最好。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.