气相色谱-质谱联用测定紫花苜蓿中的硒蛋氨酸

建立了气相色谱质谱联用(GC—MS)测定紫花苜蓿中硒蛋氨酸含量的方法。将紫花苜蓿中提取的叶蛋白样品在6 mol/L HCl溶液中,超声处理20 min。离心分离后,以丁醇及三氟乙酸酐为衍生化试剂对硒蛋氨酸进行衍生化,采用选择离子监测模式对衍生物进行GC—MS测定。硒蛋氨酸的回收率为97.6%~105.2%,相对标准偏差为1.7%~3.6%,检出限为0.3 mg/L。该法样品前处理简单,测定快速,结果准确,灵敏度高,可用于植物样品中硒蛋氨酸含量的测定。     

微波消解-电感耦合等离子体质谱法测定粮食中12种重金属元素

粮食样品用硝酸-过氧化氢微波消解处理,采用电感耦合等离子体质谱法测定样品溶液中12种重金属元素(砷、铅、镉、硒、铬、铊、锰、镍、铜、铀、钴、钒)的含量。采用内标法消除基体的影响。方法的检出限(3S/N)在0.092~17.5pg·g-1之间。方法的加标回收率在88.1%~118%之间,相对标准偏差(n=5)小于6.0%。方法用于鸡肉标准物质(GBW 10018)中重金属含量的测定,测定值与认定值相符。     

六极杆碰撞反应池-等离子体质谱测定生物样品中痕量铬和钒

采用带六极杆碰撞反应池的电感耦合等离子体质谱直接测定了生物样品中痕量铬和钒。在碰撞反应池中引入He/NH3(93∶7)混合气,有效地消除了分子离子(ArC 、NCl 、Cl O 、Cl OH 等)对超痕量铬、钒测定的干扰,降低了方法的检出限。比较了干法灰化和湿法消解两种样品处理方法,两种消解方式获得的结果基本一致。方法的检出限(3σ):钒为0.005 0μg.g-1,铬为0.001 8μg.g-1。相对标准偏差:钒为3.25%~14.08%;铬为4.20%~8.24%。经国家一级生物标准物质验证,测定值与标准值吻合。     

气相色谱-质谱法测定富硒酵母中的硒蛋氨酸

建立了气相色谱-质谱（GC-MS）测定富硒酵母中硒蛋氨酸含量的方法。比较了3种从样品中提取硒蛋氨酸方法的效果。样品在三羟甲基氨基甲烷（Tris）缓冲液中酶解24 h后,以丁醇及三氟乙酸酐为衍生化试剂对硒蛋氨酸进行衍生化,采用选择离子模式对衍生物进行GC-MS测定。硒蛋氨酸的回收率为98.5%~103.7%,相对标准偏差为0.9%~2.4%,检出限为0.5 mg/L（S/N=3）。对实际样品进行测定,得到样品中硒蛋氨酸的含量结果。该法简便快速,准确可靠,灵敏度高。     

火花直读光谱法测定铝及铝合金中的钒含量

通过对测定条件的优化,采用高钒系列标准样品建立分析程序,完成类型标准化,校验后再进行测定,建立了火花直读光谱法对铝及铝合金中的钒含量进行测定的方法。选用E2235高钒标准样品进行标准化,所得测定值与标准值基本一致,相对标准偏差为2.9%(n=8)。结果表明,当测定元素含量不超过0.020%时,方法准确、可靠,适合于铝及铝合金中微量钒含量的测定。     

电感耦合等离子体质谱（ICP-MS）法与氢化物发生-原子吸收光谱（HG-AAS）法测定土壤中硒含量的对比研究

基于氢化物发生器与原子吸收光谱联用(HG-AAS),测定土壤样品中硒的含量,并与电感耦合等离子体质谱(ICP-MS)法测定值进行了对比。在两种仪器的最佳工作条件下,测定土壤硒的含量,实验结果表明:ICP-MS法和HG-AAS法对土壤硒含量测定的线性范围分别为0.85~100.00μg/L和0.08~16.00μg/L,检出限分别为0.25μg/L和0.02μg/L,精密度分别为1.3%和2.1%;用加标回收实验和测定国家标准土壤样品(GSS-7)对这两种方法的准确性进行了验证,ICP-MS法和HG-AAS法的加标回收率分别为96.7%~99.4%和94.9%~99.5%,GSS-7标准土样的结果均在标准值范围内,说明这两种测定土壤中硒含量的方法是准确可靠的。HG-AAS法测定线性范围窄,部分样品需要稀释,而且氢化物发生系统是手动进样,导致操作复杂,分析周期长;ICP-MS法仪器测定快速,但是仪器昂贵。     

催化动力学光度法测定钒尾矿中痕量钒(Ⅴ)

基于硫酸-柠檬酸钠介质中,钒(Ⅴ)催化H2O2氧化甲基绿的显色反应,建立了测定痕量钒(Ⅴ)的光度分析新方法。确定了催化褪色反应测定钒(Ⅴ)的动力学条件,催化反应的表观活化能E′a=83.34kJ/mol,反应速率常数K′=2.25×10-4/s。方法线性范围为0.20～80μg/L,检出限为0.88μg/L。方法的表观摩尔吸光系数ε=3.31×105L/(mol·cm)。用于本地钒尾矿中钒含量的测定,相对标准偏差为2.2%～2.9%,标准加入回收率为98.8%～102.9%。     

双四极杆电感耦合等离子体质谱(ICP-MS/MS)法测定婴幼儿配方奶粉中的硒含量

应用电感耦合等离子质谱法测定婴幼儿配方食品中硒元素含量时,由于硒元素存在难电离、质谱干扰等原因往往导致硒元素测定含量偏高,方法通过含碳有机物增敏,不同分析模式去干扰从而建立能准确测量婴幼儿配方食品中硒元素含量的电感耦合等离子体质谱方法。试验方法采用分析不同含碳有机物如甲醇、乙醇、异丙醇、正丁醇的增敏效果,考察有机物浓度0%-10%范围内的影响,并研究标准模式（no gas模式）, 单杆氦气碰撞模式（He模式）,串联氦气碰撞模式（HeHe模式）、串联氧气反应模式（O2模式）等不同分析模式下的抗质谱干扰能力,确定婴幼儿配方奶粉中硒含量分析的最佳条件。结果表明具有最佳增敏效果的试剂为5%正丁醇,相较于其他分析模式,串联氧气反应模式检测婴幼儿奶粉质控样中的硒含量更加准确,该方法在0.50-10.00μg/L范围内呈现良好的线性关系(r2＞0.999),平均回收率为94.3~100.4%,精密度小于5%,方法检出限和定量限分别为0.1μg/100g和0.3μg/100g,与原子荧光分光光度法做t检验比较,各类市售婴幼儿配方食品中硒含量测定值无显著性差异(P＞0.05)。本方法操作简便、检出限低、检测结果准确,适合于婴幼儿配方食品中硒元素的准确测量。     

紫外分光光度法测定硒氧化过程中二氧化硒

利用5-硝基-2,1,3-苯并苤硒脑对紫外光的吸收特性,用紫外分光光度计测定硒氧化过程中硒(Ⅳ)含量。研究了硒(Ⅳ)与4-硝基邻苯二胺(NPDA)生成5-硝基-2,1,3-苯并苤硒脑的衍生反应条件,验证了测定结果的准确性。结果表明:衍生反应适宜条件为pH2,反应温度60℃,反应时间10 min,NPDA试剂用量为硒(Ⅳ)的168倍。在0.002~0.02 g/L硒(Ⅳ)范围内,硒(Ⅳ)浓度与衍生产物5-硝基-2,1,3-苯并苤硒脑的吸光度线性关系良好。用该法测定硒氧化过程中二氧化硒含量,RSD为0.52%。硒(Ⅳ)的平均加标回收率为98.12%。本文建立的紫外分光光度法为硒含量较大的体系中硒(Ⅳ)定量分析提供了准确、便捷的测定方法,对于其它价态硒(Ⅵ价、Ⅱ价、0价)测定有借鉴作用。     

微波消解-电感耦合等离子体质谱法同时测定泥鳅中18种微量元素

建立了微波消解-电感耦合等离子体质谱(ICP-MS)同时测定泥鳅中镁、钒、铬、锰、铁、镍、铜、锌、砷、硒、镉、锡、汞和铅等18种微量元素的分析方法。实验中采用八级杆碰撞-反应池技术消除了多种原子离子质谱干扰,以Sc,In,Rh,Ir为内标元素校正了质谱分析中基体效应并补偿了信号漂移。方法的线性范围可达到6个数量级,r≥0.9995;检出限为0.004~37.5μg/kg。选择国家一级标准物质鸡肉(GBW10018)、扇贝(GBW10024)、大虾(GBW10050)、猪肝(GBW10051)验证方法的可靠性,待测元素测定结果均在标准值允许范围内,日间相对标准偏差(n=6)在0.79%~15%之间。应用该方法测定了连云港10个主要泥鳅养殖基地不同品种的泥鳅样品,发现泥鳅中富含大量人体所必需的Mg,Fe,Zn,Cu,Mn,Se等微量元素,而Cd,Pb,Cr,Hg等有害元素含量均符合水产品中相关限量标准要求。根据测定结果,建立了连云港出口泥鳅的元素指纹图谱,发现不同养殖基地不同品种的泥鳅样品中元素分布具有共同特征,可作为泥鳅与其它鱼类鉴别的参考依据。     

微波消解-ICP-MS法测定硫磺中18种微量元素

建立了用微波消解-电感耦合等离子体质谱法(ICP-MS)同时测定硫磺中18种微量元素(锂、镁、铝、钙、钒、铬、锰、铁、钴、镍、铜、锌、镉、砷、硒、钡、铅和汞)的定量分析方法。通过对消解所用试剂及条件进行研究,确定最佳的样品处理条件;为了获得最佳的信噪比并降低光谱干扰,研究采用单变量方法,对ICP-MS的射频功率和雾化气体流量等因素进行了性能优化。结果显示：该方法各元素的校准曲线线性相关系数在0.999以上,所有元素的检出限(LODs) 在0.001-0.962 mg/Kg之间,测定下限范围在0.004-3.85 mg/Kg之间,回收率在82.9 %~115 %之间,相对标准偏差均小于3 %。     

增敏剂改进超级微波消解-电感耦合等离子体质谱(ICP-MS)法测定食品中硒元素

合适比例增敏剂会对超级微波消解-电感耦合等离子体质谱法(ICP-MS)测定食品中硒元素含量具有一定的优化效果。本文采用超级微波消解仪对1.0 g食品样品进行全消解,采用碰撞池模式规避质谱干扰,内标校正非质谱干扰,选择甲醇、乙醇、乙酸、异丙醇、丙三醇作为增敏剂,并调整测试过程中的添加比例,用电感耦合等离子体质谱法测定。结果表明：2%异丙醇存在时硒元素各同位素响应值最高,其中78Se具有低至0.0003 mg·kg-1的方法检出限;用以上方法对食品标准物质（GSB-8、GSB-9、GSB-24、GSB-30）及实际样品进行分析,标准物质测定值均在其认定值及不确定度范围内,相对误差小于-5.4%;实际样品测定值的相对标准偏差（n=7,RSD）为0.3~1.7%,加标回收率为99.2~105%。本方法操作简便,精密度好,准确度高,可以作为各类食品样品中硒含量测试方法。     

Spectrophotometric determination of trace amounts of selenium with catalytic reduction of bromate by hydrazine in hydrochloric acid media

A method is presented for the determination of selenium, based on the catalytic effect of selenium(IV) on the reduction reaction of BrO(-)(3) by N(2)H(4).2HCl. The decolourization of Methyl Orange by the reaction products was used to monitor the reaction spectrophotometrically at 525 nm. This method is precise, highly sensitive, simple, rapid, widely applicable and selective for the determination of selenium(IV) and total selenium. The variables which affected the reaction rate were fully investigated and the optimum conditions were established. Selenium, as low as 1 ng/ml, can be determined by this method. The relative standard deviation of 20 ng of selenium was 0.94% (N = 10). The method was applied to the determination of Se(IV) in a health-care product.     

Simultaneous spectrophotometric determination of iron and vanadium by H-point standard addition method and partial least squares regression in micellar medium

Simultaneous determination of total iron and vanadium by H-point standard addition method (HPSAM) and partial least squares (PLS) is described. Gallic acid (GA) in a cationic micellar solution of CTAB was used for determination of iron and vanadium in different oxidation states at pH 5. The presence of a micellar system enables total iron and vanadium to be determined with improved sensitivities. The total relative standard error for applying the PLS method to 15 synthetic samples in the ranges 0.20–15.00 μg ml⁻¹ iron and 0.20–8.00 μg ml⁻¹ vanadium was 2.2%. The results of applying the H-point standard addition method showed that iron and vanadium can be determined simultaneously with the concentration ratios of iron to vanadium from 10:1 to 1:20 in the mixed sample. Both HPSAM and PLS methods showed suitable abilities to resolve accurately overlapped absorption spectra of the compounds. Both proposed methods were successfully applied to the determination of Fe and V in several synthetic alloy solutions.     

Determination of selenium in human serum by liquid chromatography/electron capture atmospheric pressure chemical ionization mass spectrometry after acid digestion and derivatization using 2,3-diaminonaphthalene

Analysis of selenium in biological samples is very important and numerous analytical methods for the element have been developed. One of the most convenient and widely used methods for routine determination of serum selenium is a fluorometric method using 2,3-diaminonaphthalene (DAN); however, this method lacks specificity. We observed that 4,5-benzopiazselenol (BPS), a selenium derivative of DAN, is ionized with electron capture in an atmospheric pressure chemical ionization (APCI) interface, and subsequently established a method for determining total human serum selenium by means of liquid chromatography/atmospheric pressure chemical ionization mass spectrometry. All pretreatment procedures were carried out in a single test tube to minimize selenium loss. The recovery of organic or inorganic selenium spiked to human serum was 97-103%.The detection limit of BPS was equivalent to 0.2 ng of selenium and the lower quantitative limit of serum selenium was 10 ng mL(-1). The coefficient of variation of standard concentrations in control serum samples was 4.5%. The purity of the observed peak obtained from serum samples was confirmed using the ion cluster technique.     

Application of factorial designs and Doehlert matrix in optimization of experimental variables associated with the preconcentration and determination of vanadium and copper in seawater by inductively coupled plasma optical emission spectrometry

In the present paper a procedure for preconcentration and determination of vanadium and copper in seawater using inductively coupled plasma optical emission spectrometry (ICP OES) is proposed, which is based on solid-phase extraction of vanadium (IV), vanadium (V) and copper (II) ions as 1-(2-pyridylazo)-2-naphthol (PAN) complexes by active carbon. The optimization process was carried out using two-level full factorials and Doehlert matrix designs. Four variables (PAN mass, pH, active carbon mass and shaking time) were regarded as factors in the optimization. Results of the two-level full factorial design 2⁴ with 16 runs for vanadium extraction, based on the variance analysis (ANOVA), demonstrated that the factors pH and active carbon mass, besides the interaction (pH×active carbon mass), are statistically significant. For copper, the ANOVA revealed that the factors PAN mass, pH and active carbon mass and the interactions (PAN mass×pH) and (pH×active carbon mass) are statistically significant. Doehlert designs were applied in order to determine the optimum conditions for extraction. The procedure proposed allowed the determination of vanadium and copper with detection limits (3σ/S) of 73 and 94 ng l⁻¹, respectively. The precision, calculated as relative standard deviation (R.S.D.), was 1.22 and 1.37% for 12.50 μg l⁻¹ of vanadium and copper, respectively. The preconcentration factor was 80. The recovery achieved for determination of vanadium and copper in the presence of several cations demonstrated that this procedure improved the selectivity required for seawater analysis. The procedure was applied to the determination of vanadium and copper in seawater samples collected in Salvador City, Brazil. Results showed good agreement with other data reported in the literature.     

Kinetic spectrophotometric determination of trace amounts of selenium and vanadium

A sensitive kinetic spectrophotometric method has been developed for the determination of Se(IV) over the range of 45 to 4000 ng in 10 mL of solution. The method is based on the catalytic effect of Se(IV) on the reduction reaction of bromate by hydrazinium dichloride, with subsequent reaction of Ponceau S with products of the above reaction (chlorine and bromine), causing color changing of Ponceau S. Method development includes optimization of time interval for measurement of slope, pH, reagents concentration, and temperature. The optimized conditions yielded a theoretical detection limit of 33 ng/?10 mL of solution of Se(IV). The interfering effects were studied and removed. The method was applied to the determination of selenium in spiked water, Kjeldahl tablet, selenium tablet, and shampoo. Vanadium(V) has an inhibition effect on the catalyzed reaction of bromate and hydrazine by selenium. Using this effect, V(V) can be determined in the range of 70 to 2500 ng in 10 mL of solution. The optimization procedure includes pH and selenium concentration. An extraction method was used for interference removal. The method was applied to the determination of vanadium in petroleum. Received: 20 October 1998 / Revised: 17 April 1999 / Accepted: 3 June 1999     

A definitive RNAA method for determination of selenium in biological samples: uncertainty evaluation and assessment of degree of accuracy

This article describes work on the development of a highly accurate RNAA method for determination of selenium in biological samples. The analytical post-irradiation procedure is based on a combination of cation-exchange and extraction chromatography with final selective and quantitative fixation of selenium on a column packed with 3,3′-diaminobenzidine (DAB) supported on Amberlite XAD4, followed by gamma-ray spectrometric measurement. The suitability and accuracy of the method was demonstrated by analysing CRMs with certified selenium content. The uncertainty budget for Se determination in standard reference material Peach Leaves NBS 1547 was estimated; the combined standard uncertainty was calculated as 1.7%. The described method fulfils all the criteria for definitive methods. It was subsequently used for determination of selenium in biological materials intended as new CRMs and proficiency test samples.     

A method for correction of matrix effects in activation analysis based on characteristic X-ray measurements

The empirical coefficient method represents the absorption and enhancement effect of each element on each other by parameters independent of mass concentrations. This method is used together with the internal standard method for the determination of cadmium, bromine and selenium by 14 MeV neutron activation followed by X-ray spectrometry. The results of analysis show a relative error not more than ±5%.