含Chern-Simons项的(2+1)维标量量子电动力学

本文用一种方便的微扰展开方法,将一个含有Chem-Simons项的(2+1)维标量量子电动力学(QED)模型中的标量场φ量子化,在一圈图近似下,导出矢量场A_μ的等效作用量,从而证明有两支(不稳定的)元激发谱。Chern-Simons项的耦合系数不受φ场量子化的影响。     

(Nd1-x Erx)3 Fe25 Cr4.0(0≤x≤1.0)化合物的结构与磁性

合成了 (Nd1 -xErx) 3Fe2 5Cr4 . 0 (0≤x≤ 1 .0 )系列化合物并采用x射线衍射和磁测量等手段研究了它们的结构和磁性 .发现当 0≤x≤ 0 . 8时化合物保持Nd3(Fe,Ti) 2 9型结构 ,属于单斜晶系 ,A2 m空间群 ,当 0 8相似文献   

Nb掺杂导致LaMnO_3绝缘体-金属转变的第一性原理研究

采用基于密度泛函理论(DFT)的第一性原理计算,系统研究了Nb掺杂LaMn_(1-x)Nb_xO_3(x=0,0. 25,0. 5,0. 75)的结构和电磁性质.计算结果表明,所有的LaMn_(1-x)Nb_xO_3都稳定在正交结构. LaMn_(1-x)Nb_xO_3当x 0. 5时为A型反铁磁绝缘体,在x=0. 5和0. 75时为G型反铁磁金属.随着Nb掺杂量增加,当x=0. 5时掺杂电子占据导带的底部,系统产生绝缘体-金属转变.这意味着LaMn_(1-x)Nb_xO_3在电子器件上可能有重要的应用.另外,LaMn_(1-x)Nb_xO_3在x=0. 25和0. 75时出现了自旋玻璃行为.     

Ti1－xCoxO2铁磁性半导体薄膜研究

利用射频磁控反应溅射制备了Ti1-xCoxO2薄膜样品.超导量子干涉仪(SQUID)测量了样品在常温，低温下的磁特性.结果显示样品在常温下已经具有明显的铁磁性.常温时其矫顽力32×103A/m,饱和磁化强度55emu／cm3磁性元素的磁矩达0679μB／Co.饱和场12×104A/m.x射线衍射(XRD)和x射线光电子能谱(XPS)实验分析初步表明样品中没有钴颗粒. 关键词： 铁磁半导体 TiO2 薄膜     

(Nd1－xErx)3Fe25Cr4.0(0≤x≤1.0) 化合物的结构与磁性

合成了(Nd1-xErx)3Fe25Cr4.0(0≤x≤1.0)系列化合物并采用x射线衍射和磁测量等手段研究了它们的结构和磁性.发现当0≤x≤0.8时化合物保持Nd3(Fe,Ti)29型结构,属于单斜晶系,A2/m空间群,当0.8＜x≤1.0时,化合物形成一种哑铃对Fe-Fe无序替代Th2Ni17结构,P63/mmc空间群.随着Er含量的增加,化合物的居里温度TC和饱和磁化强度Ms单调下降.当x=0时,Nd3Fe25Cr4.0化合物的易磁化方向非常靠近[040]方向,仅略微偏离15结构的基面,但随Er含量的增加,(Nd1-xErx)3Fe25Cr4.0化合物的易磁化方向从靠近[040]方向转向靠近[4 0 2]方向,同时与15结构的基面所成的倾角也增大.通过测量交流磁化率发现,x=0-0.4和x=1.0的化合物在低温下出现自旋重取向.在x=0-0.4的化合物中,自旋重取向温度Tm随Er含量增加单调升高.用高达13T的磁场测量难磁化方向的磁化曲线发现,在0≤x≤0.8的化合物中发生了一级磁化过程(FOMP),其临界场Bcr随Er含量的增加而降低.     

类富勒烯纳米晶CNx薄膜及其场致电子发射特性

利用微波等离子体增强化学气相沉积技术制备出了CNx薄膜,并利用x射线光电子能谱、x射线衍射、扫描电子显微镜和Raman光谱等测试手段对所制备的CNx薄膜的微结构和成分进行了分析.研究了其场致电子发射特性.发现薄膜的结构和场发射特性与反应系中的甲烷、氮气及氢气的流量比有关,当甲烷、氢气及氮气流量比为8/50/50sccm时,制备的薄膜具有弯曲层状的纳米石墨晶体结构(类富勒烯结构)和很好的场发射特性.场发射阈值电场降低至1.1V/μm.当电场为5.9V/μm时,平均电流密度达70μA/cm2,发射点密度大于1×104cm-2.     

零质量玻色场,自发破缺与Goldstone定理

本文讨论零质量玻色场φ(x)在动量空间的零频部分,它不是动量趋于零时的极限,所以并不代表粒子的产生和湮灭算符。由于正则量子化得到一连续量子数,因此所有物理态都不能归一。真空变成一个无穷宽能带中的任意一个态。当φ(x)是厄米场时,真空并不存在简并,因此没有真空自发破缺;当φ(x)是复数场时,每一真空都是无穷地分立简并,因此也没有连续对称的自发破缺。利用这些态容易验证 Goldstone 定理证明中所插入的零动量零能量中间态并非代表不同数目的 Goldstone 粒子的相干迭加,也不一定与原来的真空态正交。文章亦讨论了φ(x)→φ(x)+η的生成元,它作用在φ(x)上的真空平均值及作用在真空态上的结果。     

少量Mn替代对Gd2Co17化合物结构与磁性的影响

通过X射线衍射和磁性测量研究了Gd2Co17-xMnx(x=0—1)化合物的结构和磁性.X射线衍射表明样品均为Th2Zn17型菱方结构.晶胞体积随Mn含量x线性增大,居里温度TC单调下降,饱和磁化强度Ms单调增加,化合物的磁晶各向异性场μ0Ha先随Mn含量减少,当x=0.6时达到最小,然后再增大 关键词： 2∶17型化合物 晶体结构 磁性     

RCo12-xTix(R=Y，Sm)化合物的结构与磁性研究

通过x射线衍射分析和磁性测量研究了RCo12-xTix(R=Y，Sm)化合物的结构与磁性，所有化合物全部具有ThMn12型结构.常规取向样品的x射线衍射谱表明，SmCo12-xTix化合物具有室温面磁晶各向异性，而YCo12-xTix化合物具有室温单轴磁晶各向异性.随着Ti含量的增加，SmCo12-xTix和YCo12-xTix化合物的居里温度TC及饱和磁化强度Ms均单调降低.YCo12-xTix化合物的磁晶各向异性场μ0Ha随Ti含量的增加而降低，而SmCo12-xTix化合物的磁晶各向异性场μ0Ha在x=1.74时出现一极大值，这可以用双次晶格模型来解释.     

具有Eckart势的Schrdinger方程的任意l波解析解

使用完全量子化规则计算了具有离心项的Eckart势,根据动量积分∫xBxAk(x)dx-∫x0Bx0Ak0(x)dx=nπ和Greene-Aldrich近似化条件,得到了系统的任意l波Schrdinger方程的解析解.讨论了:(1)基态和激发态下,势能范围参数λ和势阱深度η对具有不同角动量量子数的能量本征值的影响;(2)径向量子数n和角动量量子数l与能量本征值的关系.     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.     

A stereo matching algorithm using multi-peak candidate matches and geometric constraints

Gray cross correlation matching technique is adopted to extract candidate matches with gray cross correla- tion coefficients less than some certain range of maximal correlation coefficient called multi-peak candidate matches. Multi-peak candidates are extracted corresponding to three closest feature points at first. The corresponding multi-peak candidate matches are used to construct the model polygon. Correspondence is determined based on the local geometric relations between the three feature points and the multi-peak candidates. The disparity test and the global consistency checkout are applied to eliminate the remaining ambiguous matches that are not removed by the local geometric relational test. Experimental results show that the proposed algorithm is feasible and accurate.