Oxygen permeability, thermal expansion and mixed conductivity of GdxCe0.8−xPr0.2O2−δ, x=0, 0.15, 0.2

The non-linear thermal expansion behaviour observed in Ce_1−yPr_yO_2−δ materials can be substantially controlled by Gd substitution. Coulometric titration shows that the charge compensation mechanism changes with increasing x, in the system Gd_xCe_0.8−xPr_0.2O_2−δ. For x=0.15, charge compensation is by vacancy formation and destabilises the presence of Pr⁴⁺. At x=0.2, further Gd substitution is charge compensated by additionally raising the oxidation state of Pr rather than solely the creation of further oxygen ion vacancies. Oxygen concentration cell e.m.f. measurements in an oxygen/air potential gradient show that increasing Gd content decreases ionic and electronic conductivities. Ion transference numbers measured under these conditions show a positive temperature dependence, with typical values t_o=0.90,0.98 and 0.80 for x=0,0.15 and 0.2, respectively, at 950 °C. These observations are discussed in terms of defect association. Oxygen permeation fluxes are limited by both bulk ambipolar conductivity and surface exchange. However, the composition dependent trends in permeability are shown to be dominated by ambipolar conductivities, and limited by the level of electronic conductivity. At the highest temperatures, oxygen permeability of composition x=0.2 approaches that of composition x=0, Ce_0.8Pr_0.2O_2−δ, with specific oxygen permeability values approximately 2×10⁻⁹ mol s⁻¹ cm⁻¹ at 950 °C, but offering much better thermal expansion properties.     

Phase relation studies in the CeO2-Gd2O3-ZrO2 system

The phase relations in the CeO₂-Gd₂O₃-ZrO₂ system have been established after slowly cooling the samples from 1400 °C. Ceria has been used as a surrogate material in place of plutonia. About 80 compositions in Zr_1−xGd_xO_2−x/2, Ce_1−xGd_xO_2−x/2, Ce_1−xZr_xO_2.00, (Zr_0.5Ce_0.5)_1−xGd_xO_2−x/2, (Ce_0.5Gd_0.5)_1−xZr_xO_1.75+x/4, (Zr_0.5Gd_0.5)_1−xCe_xO_1.75+x/4, and (Ce_0.8Zr_0.2)_xGd_1−xO_1.5+x/2 were prepared by a three steps heating protocol. Based on the refinement of the XRD data, several phase regions namely; cubic fluorite type solid solution, C-type solid solution, and various biphasic regions could be delineated. This system showed the existence of a very wide cubic phase field. About 17.5 mol% GdO_1.5 was found to fully stabilize the cubic zirconia. On the other hand ceria did not stabilize the cubic zirconia. The anion-excess gadolinia, i.e., Gd_1−xCe_xO_1.5+x was found to retain the C-type lattite unlike pure gadolinia. The ternary phase relations were mainly characterized by the presence of wide homogeneity ranges of fluorite type or C-type phases.     

Dependence of the mixed alkali effect on temperature and total alkali oxide content in y[xLi2O·(1−x)Na2O]·(1−y)B2O3 glasses

The complex conductivity spectra of mixed alkali borate glasses of compositions y [xLi₂O·(1−x)Na₂O]·(1−y)B₂O₃ (with x=0.0, 0.2, 0.4, 0.6, 0.8, 1.0; y=0.1, 0.2, 0.3) in a frequency range between 10⁻² Hz and 3 MHz and at temperatures ranging from 298 to 573 K have been studied. For each glass composition the conductivities show a transition from the dc values into a dispersive regime where the conductivity is found to increase continuously with frequency, tending towards a linear frequency dependence at sufficiently low temperatures. Mixed alkali effects (MAEs) in the dc conductivity and activation energy are identified and discussed. It has been for the first time found that the strength of the MAE in the logarithm of the dc conductivity linearly increases with the total alkali oxide content, y, and the reciprocal temperature, 1/T.     

Synthesis and electrical conductivity of perovskite-type PrCo1−xMgxO3

Oxides in the system PrCo_1−xMg_xO₃ (x=0.0, 0.05, 0.10, 0.15, 0.20, 0.25) were synthesized by citrate technique and characterized by powder X-ray diffraction and scanning electron microscope. All compounds have a cubic perovskite structure (space group ). The maximum ratio of doped Mg in the system PrCo_1−xMg_xO₃ is x=0.2. Further doping leads to the segregation of Pr₆O₁₁ in PrCo_1−xMg_xO₃. The substitution of Mg for Co improves the performance of PrCoO₃ as compared to the electrical conductivity measured by a four-probe electrical conductivity analyzer in the temperature range from 298 to 1073 K. The substitution of Mg for Co on the B site may be compensated by the formations of Co⁴⁺ and oxygen vacancies. The electrical conductivity of PrCo_1−xMg_xO₃ oxides increases with increasing x in the range of 0.0-0.2. The increase in conductivity becomes considerable at the temperatures ?673 K especially for x?0.1; it reaches a maximum at x=0.2 and 1073 K. From x>0.2 the conductivity of PrCo_1−xMg_xO₃ starts getting lower. This is probably a result of the segregation of Pr₆O₁₁ in PrCo_1−xMg_xO₃ , which blocks oxygen transport, and association of oxygen vacancies. A change in activation energy for all PrCo_1−xMg_xO₃ compounds (x=0-0.25) was observed, with a higher activation energy above 573 K and a lower activation energy below 573 K. The reasons for such a change are probably due to the change of dominant charge carriers from Co⁴⁺ to Vö in PrCo_1−xMg_xO₃ oxides and a phase transition mainly starting at 573 K.     

Structural studies on W and Nd substituted La2Mo2O9 materials

The structure of a series of new ionic conductors based in lanthanum molybdate (La₂Mo₂O₉) has been investigated using transmission electron microscopy (TEM), high-resolution X-ray diffraction (XRD) and differential scanning calorimetry (DSC). The superstructure 2a_c×3a_c×4a_c of the low temperature α-polymorph relative to the β-polymorph was confirmed by HRTEM imaging and electron diffraction. Furthermore, the effects of partial cation substitution in the La_2−xNd_xMo₂O₉ and La₂Mo_2−yW_yO₉ series have been also evaluated in the search of new clues to understand the structure and stabilisation of the high temperature and better conductor β-polymorph. The thermal analysis studies show that Nd-substitution does not stabilise completely the β-polymorph at room temperature, although no superstructure ordering was observed by both XRD and HRTEM. On the other hand, W-substitution stabilises the cubic β-polymorph for y>0.25, although, electron diffraction indicates a slight distortion from the cubic symmetry for low W-content. This distortion disappears as the W content increases and the Rietveld refinements gradually render better results.     

The fluorite-pyrochlore transformation of Ho2−yNdyZr2O7

Twelve members of the Ho_2−yNd_yZr₂O₇ series, prepared using conventional solid state methods, have been characterised by neutron powder diffraction. Ho₂Zr₂O₇ has a defect fluorite structure whereas Nd₂Zr₂O₇ is found to adopt the ordered pyrochlore structure with the composition induced fluorite-pyrochlore transformation occurring near y=1. Rietveld analysis on the neutron data for all the compositions reveals an increase in lattice parameter as a function of y across the entire series, with a small discontinuity associated with the transformation. The neutron profile results suggest that domains of pyrochlore-type initially begin to form before crystallising into a separate phase, and therefore that anion and cation ordering processes are distinct. There is a strong correlation between the extent of disorder in the anion sublattice and the x-parameter of 48f oxygen. These results point the way to a better understanding of the stability observed in pyrochlore structures.     

Crystal structure and electrical conductivity of lanthanum-calcium chromites-titanates La1−xCaxCr1−yTiyO3−δ (x=0-1, y=0-1)

Five series of perovskite-type compounds in the system La_1−xCa_xCr_1−yTi_yO₃ with the nominal compositions y=0, x=0-0.5; y=0.2, x=0.2-0.8; y=0.5, x=0.5-1.0; y=0.8, x=0.6-1.0 and y=1, x=0.8-1 were synthesized by a ceramic technique in air (final heating 1350 °C). On the basis of the X-ray analysis of the samples with (Ca/Ti)?1, the phase diagram of the CaTiO₃-LaCr^IIIO₃-CaCr^IVO₃ quasi-ternary system was constructed. Extended solid solution with a wide homogeneity range is formed in the quasi-ternary system CaCr^IVO₃-CaTiO₃-LaCr^IIIO₃. The solid solution La_{(1−x′−y)}Ca_(x′+y)Cr^IV_x′Cr^III_{(1−x′−y)}Ti_yO₃ exists by up to 0.6-0.7 mol fractions of CaCr^IVO₃ (x^′<0.6-0.7) at the experimental conditions. The crystal structure of the compounds is orthorhombic in the space group Pbnm at room temperature. The lattice parameters and the average interatomic distances of the samples within the solid solution ranges decrease uniformly with increasing Ca content. Outside the quasi-ternary system, the nominal compositions La_0.1Ca_0.9TiO₃, La_0.2Ca_0.8TiO₃, La_0.4Ca_0.6Cr_0.2Ti_0.8O₃ and La_0.3Ca_0.7Cr_0.2Ti_0.8O₃ in the system La_1−xCa_xCr_1−yTi_yO₃ were found as single phases with an orthorhombic structure. In the temperature range between 850 and 1000 °C, the synthesized single-phase compositions are stable at pO₂=6×10⁻¹⁶-0.21×10⁵ Pa. Oxygen stoichiometry and electrical conductivity of the separate compounds were investigated as functions of temperature and oxygen partial pressure. The chemical stability of these oxides with respect to oxygen release during thermal dissociation decreases with increasing Ca-content. At 900 °C and oxygen partial pressure 1×10⁻¹⁵-0.21×10⁵ Pa, the compounds with x>y (acceptor doped) are p-type semiconductors and those with x<y (donor doped) and x=y are n-type semiconductors. The type and level of electrical conductivity are functions of the concentration ratios of cations occupying the B-sites of the perovskite structures: [Cr³⁺]/[Cr⁴⁺] and [Ti⁴⁺]/[Ti³⁺]. The maximum electrical conductivity at 900 °C and pO₂=10⁻¹⁵ Pa was found for the composition La_0.1Ca_0.9TiO₃ (near 50 S/cm) and in air at 900 °C for La_0.5Ca_0.5CrO₃ (close to 100 S/cm).     

The Crystal Structures, Microstructure and Ionic Conductivity of Ba2In2O5 and Ba(InxZr1−x)O3−x/2

This paper describes the results of electron microscopy, high-temperature powder neutron diffraction, and impedance spectroscopy studies of brownmillerite-structured Ba₂In₂O₅ and perovskite structured Ba(In_xZr_1−x)O_3−x/2. The ambient temperature structure of Ba₂In₂O₅ is found to adopt Icmm symmetry, with disorder of the tetrahedrally coordinated (In³⁺) ions of the type observed previously in Sr₂Fe₂O₅. Ba₂In₂O₅ undergoes a ∼6-fold increase in its ionic conductivity over the narrow temperature range from ∼1140 K to ∼1230 K, in broad agreement with previous studies. This transition corresponds to a change from the brownmillerite structure to a cubic perovskite arrangement with disordered anions. Electron microscopy investigations showed the presence of extended defects in all the crystals analyzed. Ba(In_xZr_1−x)O_3−x/2 samples with x=0.1 to 0.9 adopt the cubic perovskite structure, with the lattice parameter increasing with x.     

O NMR studies of local structure and phase evolution for materials in the Y2Ti2O7-ZrTiO4 binary system

¹⁷O MAS NMR and XRD studies of precursor-derived Y_1.6Zr_0.4Ti₂O_7.2 and Y_1.2Zr_0.8Ti₂O_7.4 have been performed to investigate the development of local and long-range order in these materials as they evolve from a metastable amorphous state upon heating. Zirconium titanate (ZrTiO₄) was also investigated to help interpret the ¹⁷O NMR spectra of the ternary compositions. Consistent with earlier studies, crystallization was observed at 800 °C to form a fluorite structure and a small amount of rutile; weak broad reflections were also observed which were ascribed to the presence of small pyrochlore-like ordered domains or particles within the fluorite phase. As the temperature was increased further, the sizes of these domains grew along with the concentration of rutile. At the highest temperature studied (1300 °C), the reflections of the thermodynamic phases, pyrochlore and zirconium titanate (ZrTiO₄), dominated the XRD pattern. The ¹⁷O NMR spectra revealed a series of different peaks that were assigned to different 3- and 4-coordinate O local environments. The data were consistent with the formation of a metastable phase Y_2−xZr_xTi_2−yZr_yO_7+x with pyrochlore-like ordering but with Zr substitution on both cation sites of the pyrochlore structure. At low temperatures, doping on the A (Y³⁺) sites predominates (i.e., x>y), consistent with the fact that the pyrochlore develops out of a more disordered fluorite-like, phase. As the temperature is raised, the Zr doping on the A site decreases and the metastable phase at this temperature can now be written as Y_2−x′Zr_x′Ti_2−y′Zr_y′O_7+x′ (i.e., x′<y′); TiO₂ is also observed, consistent with this suggestion. At high temperatures, doping on the B site decreases and the resonances due to the stoichiometric pyrochlore yttrium titanate (Y₂Ti₂O₇) dominate the NMR spectra. Weaker ¹⁷O NMR resonances due zirconium titanate (ZrTiO₄) are also observed.     

Order-disorder transition in the Nd2−yYyZr2O7 system: Probed by X-ray diffraction and Raman spectroscopy

A series of compositions having the general formula Nd_2−yY_yZr₂O₇ have been synthesized by heating of mixtures of oxides of the components cation and characterized by X-ray diffraction and Raman spectroscopy. Rietveld analysis on the XRD data of all the compositions has been performed which revealed a decrease in lattice parameter as a function of y in the series Nd_2−yY_yZr₂O₇ (y=0.0-0.8). Subsequently, a biphasic region starts which continues for y=1.2 and 1.6. The other end member, i.e. Y₂Zr₂O₇ is found to be defect fluorite. On the other hand, Nd³⁺ has been used as surrogate material for Am³⁺, which is a minor actinide found in spent nuclear fuel. In the pyrochlore range, the increasing trend of the x-parameter of 48f oxygen indicates the enhancement of disorder in the system. Raman spectroscopy has been employed to validate the data obtained from XRD. The involvement of 48f oxygen in disorder has also been verified by Raman spectroscopic investigation.     

Oxygen-ion and electron conductivity in Sr2(Fe1−xGax)2O5

High-temperature electrical conductivity measurements, structural data from powder X-ray diffraction and ⁵⁷Fe Mössbauer spectroscopy were combined to study the interrelationship of oxygen ion transport and p- and n-type transport in Sr₂(Fe_1−xGa_x)₂O₅, where x=0, 0.1 and 0.2. Although gallium substitution generally decreases the total ion-electron transport, the transition of the orthorhombic brownmillerite structure to a cubic phase on heating results in the recurrence of the conductivity to the same high level as in the parent ferrite (x=0). The changes of the partial contributions to the total conductivity as a function of x are shown to reflect a complicated interplay of the disordering processes that develop in the oxygen sublattice on heating in response to replacement of iron with gallium.     

Lanthanum pyrochlores and the effect of yttrium addition in the systems La2−xYxZr2O7 and La2−xYxHf2O7

The crystal structures of the compounds La_2−xY_xZr₂O₇ and La_2−xY_xHf₂O₇ with x=0.0, 0.4, 0.8, 1.2, 1.6, and 2.0 have been studied using neutron powder diffraction and electron microscopy to determine the stability fields of the pyrochlore and fluorite solid solutions. The limits of pyrochlore stability in these solid solutions are found to be close to La_0.8Y_1.2Zr₂O₇ and La_0.4Y_1.6Hf₂O₇, respectively. In both systems the unit cell parameter is found to vary linearly with Y content across those compositions where the pyrochlore phase is stable, as does the x-coordinate of the oxygen atoms on the 48f (x,,) sites. In both systems, linear extrapolations of the pyrochlore data suggest that the disordering is accompanied by a small decrease in the lattice parameter of approximately 0.4%. After the pyrochlore solid solution limit is reached, a sharp change is observed from x∼0.41 to 0.375 as the disordered defect fluorite structure is favoured. Electron diffraction patterns illustrate that some short-range order remains in the disordered defect fluorite phases.     

Crystal chemistry of Co-doped Zn7Sb2O12

Zn₇Sb₂O₁₂ forms a full range of Co-containing α solid solutions, Zn_7−xCo_xSb₂O₁₂, with an inverse-spinel structure at high temperature. At low temperatures for x<2, the solid solutions transform into the low temperature β-polymorph. For x=0, the β→α transition occurs at 1225±25 °C; the transition temperature decreases with increasing x. At high x and low temperatures, α solid solutions are formed but are non-stoichiometric; the (Zn+Co):Sb ratio is >7:2 and the compensation for the deficiency in Sb is attributed to the partial oxidation of Co²⁺ to Co³⁺. From Rietveld refinements using ND data, Co occupies both octahedral and tetrahedral sites at intermediate values of x, but an octahedral preference attributed to crystal field stabilisation, causes the lattice parameter plot to deviate negatively from the Vegard's law. Sub-solidus compatibility relations in the ternary system ZnO-Sb₂O₅-CoO have been determined at 1100 °C for the compositions containing ?50% Sb₂O₅.     

Luminescent and structural properties of the series Ba6−xEuxTi2+xTa8−xO30 and Ba4−yKyEu2Ti4−yTa6+yO30

The series Ba_6−xEu_xTi_2+xTa_8−xO₃₀ and Ba_4−yK_yEu₂Ti_4−yTa_6+yO₃₀ have been synthesized at 1400°C in air. They exhibit efficient excitation at about 400 nm and typical emission of Eu³⁺ at about 580-620 nm, form solid solutions within 0.0?x?2.0 and 0?y?4 respectively, and crystallized in P4/mbm at room temperature with Eu atoms occupied at centrosymmetric site (0, 0, 0). Their conductivity is very low (2.8×10⁻⁶ Ω⁻¹ cm⁻¹ at 740°C for Ba₆Ti₂Ta₈O₃₀).     

Evolution and characterization of fluorite-like nano-SrBi2Nb2O9 phase in the SrO-Bi2O3-Nb2O5-Li2B4O7 glass system

Transparent glasses of various compositions in the system (100−x)Li₂B₄O₇−x(SrO-Bi₂O₃-Nb₂O₅) (where x=10, 20, 30, 40, 50 and 60, in molar ratio) were fabricated via splat quenching technique. The glassy nature of the as-quenched samples was established by differential thermal analyses. X-ray powder diffraction (XRD) and transmission electron microscopic studies confirmed the amorphous nature of the as-quenched and crystallinity in the heat-treated samples. Fluorite phase formation prior to the perovskite SrBi₂Nb₂O₉ phase was analyzed by both the XRD and high-resolution transmission electron microscopy. Dielectric and the optical properties (transmission, optical band gap and Urbach energy) of these samples have been found to be compositional dependent. Refractive index was measured and compared with the values predicted by Wemple-Didomemenico and Gladstone-Dale relations. The glass nanocomposites comprising nanometer-sized crystallites of fluorite phase were found to be nonlinear optic active.     

Temperature and composition dependent structural investigation of the defect perovskite series Sr1−xTi1−2xNb2xO3, 0≤x≤0.2

The crystal structure of the defect perovskite series Sr_1−xTi_1−2xNb_2xO₃ has been investigated over a range of temperatures using high-resolution synchrotron X-ray diffraction, neutron diffraction and electron diffraction. Three distinct regions were observed: 0<x≤0.125 was a solid solution of Sr_1−xTi_1−2xNb_2xO₃ with minor SrTiO₃ intergrowth, 0.125<x≤0.2 was a pure Sr_1−xTi_1−2xNb_2xO₃ solid solution adopting the cubic perovskite type structure (Pm3¯m) and for x>0.2 Sr_0.8Ti_0.6Nb_0.4O₃ and Sr₃TiNb₄O₁₅ formed a two phase region. The cubic structure for Sr_0.8Ti_0.6Nb_0.4O₃ was stable over the temperature range 90-1248 K and the thermal expansion co-efficient was determined to be 8.72(9)×10⁻⁶ K⁻¹. Electron diffraction studies revealed diffuse scattering due to local scale Ti/Nb displacements and slightly enhanced octahedral rotations that did not lead to long range order. The octahedral rotations were observed to ‘lock-in’ at temperatures below ∼75 K resulting in a tetragonal structure (I4/mcm) with anti-phase octahedral tilting about the c-axis.     

An experimental investigation of ionic transport properties in CuI-Ag2WO4 and CuI-Ag2CrO4 mixed systems

The phenomenon of ionic transport in the case of two different mixed systems (CuI)_(1−x)-(Ag₂WO₄)_x(0.15?x?0.6) and (CuI)_(1−y)-(Ag₂CrO₄)_y(0.15?y?0.5) has been investigated. Powder X-ray diffraction (XRD) analysis coupled with differential scanning calorimetry (DSC), Fourier transform infrared (FT-IR), FT-Raman and electrical transport studies involving ionic transport number and temperature-dependent electrical conductivity measurements have been carried out in order to identify the various phases responsible for the conduction process. The occurrence of typical ionic conductivity values of 4.5×10⁻³ Scm⁻¹ for the composition (CuI)_0.45-(Ag₂WO₄)_0.55 and 1.1×10⁻⁴ Scm⁻¹ in the case of (CuI)_0.55-(Ag₂CrO₄)_0.45 at room temperature has been discussed in terms of the observed characteristics.     

Structure and phase composition of nanocrystalline Ce1−xLuxO2−y

The microstructure and phase stability of nanocrystalline mixed oxide Lu_xCe_1−xO_2−y (x=0-1) are described. Nano-sized (3-4 nm) oxide particles were prepared by the reverse microemulsion method. Morphological and structural changes upon heat treatment in an oxidizing atmosphere were studied by transmission electron microscopy (TEM), X-ray diffraction (XRD), Raman and Yb³⁺ emission spectroscopy, the latter ion being present as an impurity in the Lu₂O₃ starting material. Up to 950 °C, the samples were single phase, with structure changing smoothly with Lu content from fluorite type (F) to bixbyite type (C). For the samples heated at 1100 °C phase separation into coexisting F- and C-type structures was observed for 0.35<x<0.7. It was also found that addition of Lu strongly hinders the crystallite growth of ceria during heat treatment at 800 and 950 °C.     

Structural characterization and electrical properties of NiNb2−xTaxO6 (0≤x≤2) and some Ti-substituted derivatives

A structural and electrical characterization of the system NiNb_2−xTa_xO₆ (0≤x≤2) is presented. For x≤0.25 materials with the columbite-type structure typical of NiNb₂O₆ have been obtained whereas for x≥1 tri-rutile-like oxides were obtained. The electrical properties are similar in both cases; they are semiconducting with very low electrical conductivity and very high activation energy, though slight differences were found as a function of Ta content. Improvement of conductivity by reducing the stoichiometric materials could not be achieved due to decomposition. In this connection, partial substitution of Nb or Ta by Ti has been carried out in order to create oxygen vacancies. Tantalum was partially replaced by Ti to a significant extent in the tri-rutile structure inducing a slight increasing of conductivity. However, for the columbite case neither Nb nor Ta could be partially replaced. This behavior is quite different from that reported for other similar columbites such as MnNb₂O_6−δ, which exhibits high electrical conductivity upon substitution of niobium by titanium.     

Order-disorder transition in Nd2−yGdyZr2O7 pyrochlore solid solution: An X-ray diffraction and Raman spectroscopic study

Powder X-ray diffraction (XRD) and Raman spectroscopic study of order-disorder-phase transition with increase in the content of Gd in Nd_2−yGd_yZr₂O₇ solid solution is being reported. It has been observed from Rietveld analysis that with increase in concentration of Gd in Nd_2−yGd_yZr₂O₇, the value of the x parameter of the 48f oxygen changes from 0.332(1) to 0.343(1) with a sudden change in the slope for y=1.8, which indicates that the structure is transforming from ordered pyrochlore to disordered pyrochlore. In addition to that a sudden and drastic change in the Raman spectra including changes in the position and width of several Raman modes beyond y?1.8 has also been observed which has been correlated with increasing disorder. Based on these studies, it is suggested that there is a discontinuous order-disorder transition from ‘perfect pyrochlore’ to ‘defect pyrochlore’ phase in Nd_2−yGd_yZr₂O₇ solid solution.