Numerical investigation of separated flow in front of a spiked cylinder

The problem of axisymmetric flow of a perfect heat conducting gas over a cylinder from the front of which a spike projects is solved at subsonic and supersonic velocities of the oncoming flow in the model of a viscous fluid. The formation and development of the flow separation due to the spike ahead of the front surface of the cylinder is investigated. The change in the gas-dynamic and geometrical parameters of the separated flow is studied as a function of the Mach and Reynolds numbers of the oncoming flow. The obtained results are compared with the available experimental data.Translated from Izvestiya Akademii Nauk SSSR, Mekhanika Zhidkosti i Gaza, No. 6, pp. 162–166, October–December, 1981.     

Supersonic viscous perfect gas flow past a circular cylinder

The complete Navier-Stokes equations are used to calculate supersonic perfect gas flow past a circular isothermal cylinder by the method described in [1]. The effects of the Mach number M=2.5–10 and the Reynolds number Re=30-10⁵ on the flowfield structure and heat transfer to the cylinder wall are investigated. Special attention is paid to the study of the near wake and the local characteristics on the leeward side of the cylinder.Translated from Izvestiya Rossiiskoi Akademii Nauk, Mekhanika Zhidkosti i Gaza, No.6, pp. 107–115, November–December, 1993.     

Transverse subsonic flow past a cylinder

At around the critical Reynolds number Re = (1.5–4.0)·10⁵ there is an abrupt change in the pattern of transverse subsonic flow past a circular cylinder, and the drag coefficient C_x decreases sharply [1]. A large body of both experimental and computational investigations has now been made into subsonic flow past a cylinder [1–4]. A significant contribution to a deeper understanding of the phenomenon was made by [4], which gives a physical interpretation of a number of theoretical and experimental results obtained in a wide range of Re. Nevertheless, the complicated nonstationary nature of flow past a cylinder with separation and the occurrence of three-dimensional flows when two-dimensional flow is simulated in wind tunnels do not permit one to regard the problem as fully studied. The aim of the present work was to make additional experimental investigations into transverse subsonic flow past a cylinder and, in particular, to study the possible asymmetric stable flow regimes near the critical Reynolds number.Translated from Izvestiya Akademii Nauk SSSR, Mekhanika Zhidkosti i Gaza, No. 2, pp. 154–157, March–April, 1980.     

Interference between a blunt edge shock layer and an impinging inclined shock at low Reynolds numbers

The interference between the shock layer on a cylinder modeling the leading edge of an air intake and an impinging plane inclined shock is investigated experimentally and numerically for a Reynolds number Re₀=32. The low-pressure wind tunnel experiments made it possible to visualize the flow and determine the local heat transfer in the presence of interference. The corresponding flow regimes were calculated numerically within the framework of the system of Navier-Stokes equations by the through-calculation method. The principal properties of the distribution of the flow characteristics for a low value of the Reynolds number were obtained for various types of interference and the differences with respect to the previously investigated interference regimes for high Reynolds numbers were examined.Translated from Izvestiya Rossiiskoi Akademii Nauk, Mekhanika Zhidkosti i Gaza, No. 1, pp. 166–171, January–February, 1993.     

Supersonic boundary layer transition induced by roughness on the attachment line of a yawed cylinder

The effect of a single two-dimensional irregularity and sandy roughness on boundary layer transition in supersonic flow over a yawed cylinder (M = 6)-has been experimentally investigated. The characteristic flow regimes beyond the roughness are identified, and their limits are determined as a function of the Reynolds number and the ratio of the height of the roughness to the characteristic thickness of the boundary layer. A qualitative comparison is made with the flow regimes induced by roughness on the attachment line in incompressible flow over a cylinder [1–3]. The thermal indicator coating method is used to measure the heat fluxes along the attachment line and a comparison is made with calculations carried out in accordance with the methods of other authors.Translated from Izvestiya Akademii Nauk SSSR, Mekhanika Zhidkosti i Gaza, No. 6, pp. 28–35, November–December, 1991.The authors are grateful to A. F. Kiselev for helping to calculate the heat flux in the turbulent boundary layer.     

Direct Statistical Simulation of a Supersonic Flow of a Binary Mixture of Rarefied Gases around a Transversely Positioned Cylinder

A supersonic flow of a binary mixture of gases in a wide range of rarefaction (from a flow with a Knudsen number K _n = 0.1 to a free-molecular flow) around a cylinder is studied by means of direct statistical Monte Carlo simulations (DSMC method). The influence of a small fraction of heavy particles in a light gas flow on the region of significant nonequilibrium near the cylinder and on the heat flux is considered.__________Translated from Prikladnaya Mekhanika i Tekhnicheskaya Fizika, Vol. 46, No. 5, pp. 53–59, September–October, 2005.     

Experimental study of heat and mass transfer from a horizontal cylinder in downward air-water mist flow with blockage effect

An experimental study was made on convective heat and mass transfer from a horizontal heated cylinder in a downward flow of air-water mist at a blockage ratio of 0.4. The measured local heat transfer coefficients agree fairly well with the authors' numerical solutions obtained previously for the front surface of a cylinder over the ranges mass flow ratio 0–4.5×10⁻², a temperature difference between the cylinder and air 10–43 K, gas Reynolds number (7.9–23)×10³, Rosin-Rammler size parameter 105–168 μm, and dispersion parameter 3.4–3.7. Heat transfer augmentation, two-pahse to single-phase of greater than 19 was attained at the forward stagnation point. For heat transfer in the rear part of the cylinder, an empirical formula is derived by taking into account the dimensionless governing variables, that is, coolant-feed and evaporation parameters.     

Some effects of strong blowing of gas into a supersonic flow

The intense evaporation of bodies moving in the atmospheres of planets at high supersonic velocities has been partly simulated both theoretically [1–5] (numerical calculations of strong blowing in the framework of the Navier-Stokes equations were also made at the Scientific-Research Institute of Mechanics at the Moscow State University by É. A. Gershbein and A. F. Kolesnikov [6]) as well as experimentally [7–9]. Below, the results are given of investigations of strong blowing of gas from the flat end of a cylinder into a supersonic flow at Reynolds numbers such that the mixing layer separating the blown and the oncoming gas is fairly thin. In this case, the mixing layer can be regarded as a contact surface, so that the problem of blowing can be solved in the framework of Euler's equations. The results of a numerical solution are compared with the results of experiments on the separation and profile of the shock wave, the thickness of the blowing layer on the axis, and also on the pressure distribution on the end of the cylinder. It was established experimentally, and then confirmed numerically that there is a downwash of the blown gas on the periphery of a porous end. It is shown that for the same blowing parameter K, which is equal to the ratio of the dynamic head of the blown gas to the dynamic head of the oncoming gas, and for a given distribution of K over the surface of the body the contact surface tends to a certain limiting position with increasing Mach number of the oncoming flow, i.e., the profile of the contact surface is stabilized. The influence of the adiabatic exponent on the thickness of the blowing layer is estimated. The present investigations continue earlier experimental studies, the main results of which have been presented in [9].Translated from Izvestiya Akademii Nauk SSSR, Mekhanika Zhidkosti i Gaza, No. 1, pp. 91–98, January–February, 1980.     

Numerical and experimental investigation of thermal convection for a thermodependent Herschel-Bulkley fluid in an annular duct with rotating inner cylinder

Thermal convection for an incompressible Herschel-Bulkley fluid along an annular duct, whose inner cylinder is rotating and outer is at rest, is analyzed numerically and experimentally. The outer cylinder is heated at constant heat flux density and the inner one is assumed adiabatic. The first part of this study deals with the effect of the rheological behavior of the fluid and that of the rotation of the inner cylinder on the flow field and heat transfer coefficient. All the physical properties are assumed constant and the flow is assumed fully developed. The critical Rossby number Ro_c = (R₁Ω/U_d)_c, for which the dimension of the plug flow is reduced to zero is determined with respect to the flow behavior index, the radius ratio and the Herschel-Bulkley number for axial flow. The rotation of the inner cylinder induces a decrease of the axial velocity gradient at the outer cylinder thereby reducing the heat transfer between the heated wall and the fluid. The second part of this study introduces the variation of the consistency K with temperature and analyzes the evolution of the flow pattern and heat transfer coefficient along the heating zone. Two cases are distinguished depending on the Rossby number: (i) Ro < Ro_c, the plug flow dimension increases along the heating zone; (ii) Ro < Ro_c, the decrease of K with temperature leads to the reappearance of the plug flow. For high angular velocities, it is possible to have a plug zone attached to the outer cylinder. Finally, a correlation is proposed for the Nusselt number. It shows clearly that the effect of thermodependency of K on the heat transfer becomes more important with increasing rotational velocity of the inner cylinder.     

Slow gas flow around a nonuniformly heated plate

Slow flow of a rarefied gas over a nonuniformly heated plate is investigated numerically. The interaction of the oncoming stream with the flow due to the variable temperature of the gas near the body is considered.Translated from Izvestiya Akademii Nauk SSSR, Mekhanika Zhidkosti i Gaza, No. 5, pp. 181–184, September–October, 1981.     

Transonic crossflow of condensing wet steam past a cylinder

The shadow and interferometric methods and the laser probe method are used to investigate crossflow past a cylinder on the free-stream Mach number interval M _a =0.5–1.2 for subcritical Reynolds numbers Re _d and various initial steam states. Detailed pressure distributions are obtained and the pressure fluctuations on the cylinder surface are measured. The dependence of the Strouhal number on the velocity and thermodynamic parameters of the flow are determined. In single-phase steam flow past a cylinder the greatest fluctuations occur in the separation zone in regimes corresponding to transonic drag crisis. It is shown that spontaneous condensation in the turbulent wake and local supersonic zones may cause an increase in the periodic pressure fluctuations in the separation zone, the maximum increase in the fluctuations being noted when the critical pressure ratio is reached at the rear of the cylinder. The initial wetness of the steam has the greatest effect on the periodic separation characteristics at subsonic flow velocities, and in the case of supersonic flow leads to a substantial increase in the level of the low-frequency pressure fluctuations at the front of the cylinder.(deceased)Moscow. Translated from Izvestiya Rossiiskoi Akademii Nauk, Mekhanika Zhidkosti i Gaza, No. 6, pp. 118–138, November–December, 1994.     

Exact solution of the problem of convective heat exchange for an elliptic cylinder and a plate in a fluid with small Prandtl number

The heat exchange problem is solved for an elliptic cylinder and a plate in an incompressible fluid flow with small Prandtl number Pr1. For flow along a plate, the values of the Nusselt number Nu obtained by solving the complete energy equation and the heat boundary layer equation are compared.Moscow. Translated from Izvestiya Rossiiskoi Akademii Nauk, Mekhanika Zhidkosti i Gaza, No. 3, pp. 26–31, May–June, 1996.     

Experimental modeling of three-dimensional modes of hypersonic flow past cylindrically-blunted bodies

Several sets of experimental studies of the structure of transverse hypersonic flow past blunt bodies (cylinder and truncated wedge) and heat transfer on them are performed in the UT-1M shock tube of the Central Aerohydrodynamics Institute. The purpose of the investigation was to obtain three-dimensional modes of hypersonic flow past the nose surfaces of blunt bodies in an artificially disturbed and nominally uniform flows. The controlled disturbances in the freestream were produced by thin threads pulled over the nozzle exit. In the experiment the flow was visualized using the Töpler method and the heat flux distribution over the cylinder was measured using luminescent temperature transformers. The experiments show that both the flow and the heat transfer in the vicinity of the cylinder nose are very sensitive to vortex disturbances in the oncoming hypersonic flow. In a nominally uniform flow (M_∞ = 8 and Re_∞ = 3160–11670) a steady three-dimensional mode of flow past the nose surface of a blunt wedge could be obtained in the form of a single vortex pair.     

Simulation of cross-flow-induced vibration of cylinder arrays by surface vorticity method

The surface vorticity method (SVM), which is a fast and practical grid-free two-dimensional (2-D) method, and a fluid–structure interaction model incorporating the effects of cylinder motions and displacements is used to simulate the vortex-induced vibration of cylinder arrays at sub-critical Reynolds number Re=2.67×10⁴. The SVM is found to be most suitable for simulating a 2-D cylinder row with large-amplitude vibrations where the vorticity field and the fluid forces of the cylinder row change drastically, and the effect of the stream on the transverse direction vibration is very significant. The fluidelastic instability of a flexible cylinder row at small pitch ratio is also investigated, and the critical reduced velocity of the cylinder row at a reduced damping parameter S_G=1.29 is calculated, which is in good agreement with experimental and analytical results of the unsteady model. Vortex-induced vibration of a staggered cylinder array is simulated using different structural parameters. When the cylinders are relatively more flexible, the flow pattern changes dramatically and the fluid–structure interaction has a dominant impact on the flow field. Compared with grid-based methods, the grid-free SVM is a fast and practical method for the simulation of the FIV of cylinder arrays due to vortex shedding at sub-critical Reynolds numbers.     

Free thermoconcentration convection above a localized heat source

Shadowgraph and probe techniques are used to investigate the free convective flow pattern above various localized heat sources (electrolytic cell — point source, short vertical cylinder, sphere) in an exponentially stratified fluid. The characteristic types of structure are classified with respect to the appearance of new forms of instability. The critical values of the global Rayleigh number, at which the flow pattern is restructured, are determined. The dependence of the height of the convection zone and the height of the individual cells on the governing parameters of the problem is investigated and the results are reduced to universal form. Laboratory experiments and oceanic observations are qualitatively compared.Translated from Izvestiya Akademii Nauk SSSR, Mekhanika Zhidkosti i Gaza, No. 2, pp. 27–34, March–April, 1989.     

Vibrational thermal convection about a uniformly heated cylinder

Vibrational convection under conditions of weightlessness has now been investigated for closed cavities of various geometries (see, for example, [1–3]). However, the question of vibrational convection developing around a heated body in an unconfined fluid remains open. Here, the convection developing under conditions of weightlessness about a uniformly heated infinite cylinder vibrating at high frequencies together with the fluid in a direction perpendicular to the cylinder axis is considered. The nonlinear equations of averaged motion are solved numerically by a finite-difference method. It is shown that at high values of the vibrational Grashof number boundary-layer type flow with a structure consisting of two symmetrical jets perpendicular to the direction of vibration is formed. The flow and heat transfer characteristics are determined.Translated from Izvestiya Akademii Nauk SSSR, Mekhanika Zhidkosti i Gaza, No. 3, pp. 23–26, May–June, 1989.The author wishes to thank E. M. Zhukovitskii for supervising the work.     

Drag of porous cylinders in a viscous fluid at low reynolds numbers

The problem of flow past a permeable cylinder at low Reynolds numbers is of interest for the solution of a number of problems in chemical technology in, for example, the design of porous electrodes and porous catalysts and in the calculation of nonstationary filtration of aerosols by fibrous filters. In the present paper, we solve the problem of transverse flow of a viscous fluid past a continuous cylinder in a porous shell and, in particular, in the case of a porous cylinder under conditions of constrained flow (system of cylinders) and an isolated cylinder at arbitrary permeability. The analogous problem of Stokes flow past permeable spheres has been solved in a number of papers [1–3].Translated from Izvestiya Akademii Nauk SSSR, Mekhanika Zhidkosti i Gaza, No. 6, pp. 122–124, November–December, 1979.     

Effect on the flow and heat transfer characteristics for sinusoidal pulsating laminar flow in a heated square cylinder

Two-dimensional numerical simulation is performed to understand the effect of flow pulsation on the flow and heat transfer from a heated square cylinder at Re = 100. Numerical calculations are carried out by using a finite volume method based on the pressure-implicit with splitting of operators algorithm in a collocated grid. The effects of flow pulsation amplitude (0.2 ≤ A ≤ 0.8) and frequency (0 ≤ f _p  ≤ 20 Hz) on the detailed kinematics of flow (streamlines, vorticity patterns), the macroscopic parameters (drag coefficient, vortex shedding frequency) and heat transfer enhancement are presented in detail. The Strouhal number of vortices shedding, drag coefficient for non-pulsating flow are compared with the previously published data, and good agreement is found. The lock-on phenomenon is observed for a square cylinder in the present flow pulsation. When the pulsating frequency is within the lock-on regime, time averaged drag coefficient and heat transfer from the square cylinder is substantially augmented, and when the pulsating frequency in about the natural vortex shedding frequency, the heat transfer is also substantially enhanced. In addition, the influence of the pulsating amplitude on the time averaged drag coefficient, heat transfer enhancement and lock-on occurrence is discussed in detail.     

Aerodynamic loading on a cylinder behind an airfoil

The interaction between the wake of a rotor blade and a downstream cylinder holds the key to the understanding and control of electronic cooling fan noise. In this paper, the aerodynamic characteristics of a circular cylinder are experimentally studied in the presence of an upstream NACA 4412 airfoil for the cylinder-diameter-based Reynolds numbers of Re_d=2,100–20,000, and the airfoil chord-length-based Reynolds numbers of Re_c=14,700–140,000. Lift and drag fluctuations on the cylinder, and the longitudinal velocity fluctuations of the flow behind the cylinder were measured simultaneously using a load cell and two hot wires, respectively. Data analysis shows that unsteady forces on the cylinder increase significantly in the presence of the airfoil wake. The dependence of the forces on two parameters is investigated, that is, the lateral distance (T) between the airfoil and the cylinder, and the Reynolds number. The forces decline quickly as T increases. For Re_c<60,000, the vortices shed from the upstream airfoil make a major contribution to the unsteady forces on the cylinder compared to the vortex shedding from the cylinder itself. For Re_c>60,000, no vortices are generated from the airfoil, and the fluctuating forces on the cylinder are caused by its own vortex shedding.     

Anisotropic Organised Eddy Simulation for the prediction of non-equilibrium turbulent flows around bodies

The unsteady turbulent flow around bodies at high Reynolds number is predicted by an anisotropic eddy-viscosity model in the context of the Organised Eddy Simulation (OES). A tensorial eddy-viscosity concept is developed to reinforce turbulent stress anisotropy, that is a crucial characteristic of non-equilibrium turbulence in the near-region. The theoretical aspects of the modelling are investigated by means of a phase-averaged PIV in the flow around a circular cylinder at Reynolds number 1.4×10⁵. A pronounced stress–strain misalignment is quantified in the near-wake region of the detached flow, that is well captured by a tensorial eddy-viscosity concept. This is achieved by modelling the turbulence stress anisotropy tensor by its projection onto the principal matrices of the strain-rate tensor. Additional transport equations for the projection coefficients are derived from a second-order moment closure scheme. The modification of the turbulence length scale yielded by OES is used in the Detached Eddy Simulation hybrid approach. The detached turbulent flows around a NACA0012 airfoil (2-D) and a circular cylinder (3-D) are studied at Reynolds numbers 10⁵ and 1.4×10⁵, respectively. The results compared to experimental ones emphasise the predictive capabilities of the OES approach concerning the flow physics capture for turbulent unsteady flows around bodies at high Reynolds numbers.