共查询到18条相似文献,搜索用时 156 毫秒
1.
铅球运动最佳出手角的理论分析和实验模拟研究 总被引:7,自引:3,他引:4
从理论上分析了铅球运动的初速度,出手高度,出手角度对成绩的影响,力求寻找它们之间的最佳组合,并通过模拟实验进行了论证. 相似文献
2.
本文提出了利用运动叠加原理分析铅球最佳出手角的简便方法,与传统方法就两种不同情形下求解最佳出手角进行了对比,说明了叠加原理法的简洁性.同时通过对两组理论数据的对比,说明分析铅球最佳出手角可将出手高度视为独立变量. 相似文献
3.
设出手点的高度为h,出手的初速度为v0,出手角为α,投掷远度为L,其中包括铅球出手点的垂线到抵趾板之间的距离s′,球在空中飞行的水平距离为s,即L=s′ +s,s′可以通过摄影测量获得. 相似文献
4.
阻力作用下铅球在空中运动的规律 总被引:1,自引:0,他引:1
考虑了铅球出手时具有一定的高度、初速度与投射角及铅球在空中受到的阻力等情况 ,利用Mathmatic软件对铅球的运动方程进行求解 ,得到了铅球飞行的最远距离与投射角、初速度与投射角的关系 ;进一步的研究 ,可望得到一个“选拔具有潜质铅球运动员模型”。 相似文献
5.
6.
7.
投球手的“鞭打”素质(投物时手臂挥动抛物动作叫鞭打动作,鞭打动作奸坏由鞭打素质反映)是衡量运动员的重要参量.而球体的出手速度是反映这种素质的重要指标.本文介绍了一种测量出手速度的仪器.该仪器利用光敏元件组成的光敏列阵传感系统,将投掷球出手后经过光平面的时间转换成电讯量,经“直径代最大弦长”后输入计算机处理并由计算机打印出最终结果,实现了快速启动检测与记录. 相似文献
8.
9.
建立理想的投篮模型,运用蒙特卡罗数值计算方法得出给定点的空心中框概率,并由此得到最佳投篮速度、最佳投篮角度和截止投篮速度.根据中框投篮角分析了不同投篮速度区间对应的投篮弧线,还对空心中框率和投篮距离及投篮点高度间的关系作了讨论. 相似文献
10.
11.
The non-uniform flow field around high-speed flying vehicle “bends” the ray and imposes a deviation at the end of the propagation path. This imaging deviation is a kind of aero-optic effect. In this paper, we catalog the factors that influence the deviation into two classes: the vehicle-related factors and the flowfield-related factors. Flow density computation and density–refractive index conversion are discussed. A backward ray-tracing scheme is proposed. The deviations, the propagation path distances in the non-uniform flow field, and the density distributions along propagation paths for two different flying cases are computed. Three flowfield-related factors should be considered in order to reduce the deviation: the propagation path distance in the non-uniform flow field, which should be as short as possible; the angle of incidence at the freestream boundary, which should be as small as possible; and the density distribution along propagation path in the non-uniform flow field, which should be as flat as possible. 相似文献
12.
To improve four across screens system measurement precision on flying projectile location, the new method that adds two incline screens to four intersecting screens system to form six intersecting screens was put forward and the flying object coordinate test model was set up. This method not only gains object coordinate but also measures object's pitching and azimuth angle that can amend coordinates and improve measurement precision. The differential methods were used to analyze their measure errors, which came from the angle of intersection screen, the thick of screen, the time and distance of measuring, and give out measure errors distributing. The experimental result shows the new measure method can improve measurement precision that meets test demand. 相似文献
13.
针对现有的天幕靶幕面空间位置参数检定方法需要拆卸的不足,提出一种不拆卸天幕靶对其探测幕面位置检测的方法。以经纬仪建立基准面,采用放置在基准面内特制的频闪小光源和设定天幕靶输出阈值的方式,根据小光源作用在天幕靶上有信号输出时平移台相对基准面的移动距离,实现天幕靶幕面空间位置参数的检测。将天幕面相对基准位置倾斜2、-2、-5时,所测幕面倾斜角度与实际幕面倾斜角度间误差均小于1,试验结果表明天幕靶幕面位置检定方法精度优于1,与理论分析相一致。该方法不需要拆卸天幕靶,节省了时间,能用于使用中天幕靶的检定。 相似文献
14.
15.
The detection effect of laser active detection system is affected by various kinds of factors. In view of the application requirement of laser active detection, the influence factors for laser active detection are analyzed. The mathematical model of cat eye target detection distance has been built, influence of the parameters of laser detection system and the environment on detection range and the detection efficiency are analyzed. Various parameters constraint detection performance is simulated. The results show that the discovery distance of laser active detection is affected by the laser divergence angle, the incident angle and the visibility of the atmosphere. For a given detection range, the laser divergence angle and the detection efficiency are mutually restricted. Therefore, in view of specific application environment, it is necessary to select appropriate laser detection parameters to achieve optimal detection effect. 相似文献
16.
为了提高超声喷丸强化加工的面积、效率及加工质量,对传统单振子超声喷丸强化技术进行了改进,提出了压电振子阵列型超声喷丸强化加工方法。分析了超声喷丸强化的机理,进行了压电振子的优化设计,分析了激振片的谐振响应,实验测试了系统样机在不同超声电源功率下弹丸撞击工件的区域分布;探究了超声电源功率、喷丸距离、弹丸直径和喷丸时间对加工样件显微硬度的影响,结果表明:以超声电源功率作为唯一变量,弹丸冲击工件表面的区域面积随超声电源功率增大而增大;7075铝合金样件的表面显微硬度及其提高率,随超声电源功率的增大、喷丸时间的增加、喷丸距离的减小及弹丸直径的增大而增大;超声电源功率为50W、喷丸时间为20min、喷丸距离为5mm、弹丸直径为1.5mm时喷丸效果最好,此时工件表面显微硬度增加量为65.1HV,表面显微硬度提高率为36.7%。压电振子阵列型超声喷丸强化技术可以有效增加喷丸冲击工件的面积,提高工件的表面显微硬度和加工效率。 相似文献
17.
为了降低飞行器倾斜成像工作过程中视轴角误差对TDICCD空间相机成像质量的影响,提出满足相机成像质量的视轴角范围及控制误差的要求。根据空间相机成像机理,给出了焦面像移速度以及由视轴角误差引起的像移速度匹配误差计算公式,分析了视轴角对地面像元分辨力的影响。并以调制传递函数(MTF)为约束条件给出了不同积分级数下视轴角的范围。通过实际工程参数计算得出,当视轴角控制误差为0.8时,满足96级TDICCD成像质量要求的视轴角应不大于12.75;若要满足96级TDICCD倾斜成像时视轴角达到25,则视轴角控制误差应优于0.4。 相似文献
18.
小入射角条件下气动光学成像偏移 总被引:2,自引:0,他引:2
针对超声速飞行器在大气中飞行时由于气动光学效应产生的成像偏移,推导了光线偏折角和流场折射率梯度之间的关系,给出了小入射角情况下,离散折射率场光线偏折角的一种计算方法;利用不同流场的计算流体力学数据计算出对应的折射率场;使用光线追迹法得到光线通过不同流场后的偏折角和传播路径上的折射率梯度分布。仿真结果表明,新的偏折角计算方法所得结果在入射角小于30°时与Runge-Kutta和Snell光线追迹法具有很好的一致性;同一高度下小入射角时,光线的偏折角并不随着飞行速度的增加而增加,而是基本保持稳定;光线通过流场的偏折是正负折射率梯度区域共同作用的结果,负的折射率梯度区域可以减少光线偏折,起到部分"校正"作用。 相似文献