Liquid crystalline thermosets based on anisotropic phases of cellulose nanocrystals

A new class of liquid crystalline thermosets (LCTs) was successfully produced containing lyotropic cellulose nanocrystals (CNCs) as the primary mesogenic component (up to 72 wt%) by the addition of non-mesogenic epoxy monomers. Cellulose-based LCTs were produced by totally aqueous processing methods and ultimately cured at elevated temperatures to produce ordered networks of ‘frozen’ liquid crystalline (LC) phases. Various degrees of birefringence were obtained via self-assembly of CNCs into oriented phases as observed by polarized optical microscopy and transmission electron microscopy. X-ray diffraction measurements highlighted the effects of texture of CNCs within LCT films compared to lyophilized CNCs. Cellulose-based LCT films uniquely exhibited thermo-mechanical properties of both traditional LCTs and LC elastomers, such as high elastic modulus (~1 GPa) under ambient conditions and low glass transition temperature (~?25 °C), respectively. The development of LCTs based on CNCs and aqueous processing methods provides a renewable pathway for designing high performance composites with ordered network structures and unique optical properties.     

表面官能团化增强碳纳米笼超级电容器性能

以具有多级孔结构、高比表面积、良好导电性等特征的碳纳米笼（CNCs）为前体,采用硝酸氧化法在CNCs表面引入含氧官能团。以CNCs为超级电容器电极材料,在相同电流密度下,官能团化样品的比电容显著高于纯CNCs;在1A·g^-1下比电容最高可达到255F·g^-1,比纯CNCs的188F·g^-1增加了34%,这表明表面含氧官能团化能够显著提高CNCs的超级电容器比电容。在100A·g^-1的大电流密度下,硝酸氧化后CNCs的比电容保持在111~167F·g^-1,表明具有良好的耐大电流充放电性能。在10A·g^-1的电流密度下循环10000圈后,CNC-6M样品的比电容由196F·g^-1下降到176F·g^-1,样品的比电容仍保留90%,具有良好的循环稳定性。表面含氧官能团化CNCs所表现出的这种优异的超级电容器性能归因于CNCs的多尺度分级孔结构、高比表面积、良好的导电性、表面亲水性含氧官能团化带来的浸润性提高和引入的赝电容。     

Isolation of a novel,crystalline cellulose material from the spent liquor of cellulose nanocrystals (CNCs)

We have modified the standard sulphuric acid hydrolysis method for the production of cellulose nanocrystals (CNCs) to successfully isolate a novel, highly crystalline cellulose material from the spent liquor of CNCs. The novel material has a cellulose II crystal structure that is distinctly different from the cellulose I crystal structure of CNCs. The modified method uses a shorter time for the hydrolysis, followed by maintaining a high residual acid concentration for the separation of the spent liquor and CNCs, and by adding the spent liquor to water. The modified method offers an opportunity to concurrently produce CNCs in up to ~40 % yield and the novel, highly crystalline, sulphated cellulose II in ~15 % yield in separate and pure forms from sulphuric acid hydrolysis of a commercial northern bleached softwood kraft pulp. It can potentially reduce the production cost of CNCs, allow easier downstream processing of CNCs and recovery of sulphuric acid, and generate a new cellulose bio-material for product development.     

表面官能团化增强碳纳米笼超级电容器性能

以具有多级孔结构、高比表面积、良好导电性等特征的碳纳米笼(CNCs)为前体,采用硝酸氧化法在CNCs表面引入含氧官能团。以CNCs为超级电容器电极材料,在相同电流密度下,官能团化样品的比电容显著高于纯CNCs;在1 A·g-1下比电容最高可达到255 F·g-1,比纯CNCs的188 F·g-1增加了34%,这表明表面含氧官能团化能够显著提高CNCs的超级电容器比电容。在100 A·g-1的大电流密度下,硝酸氧化后CNCs的比电容保持在111~167 F·g-1,表明具有良好的耐大电流充放电性能。在10 A·g-1的电流密度下循环10 000圈后,CNC-6M样品的比电容由196 F·g-1下降到176 F·g-1,样品的比电容仍保留90%,具有良好的循环稳定性。表面含氧官能团化CNCs所表现出的这种优异的超级电容器性能归因于CNCs的多尺度分级孔结构、高比表面积、良好的导电性、表面亲水性含氧官能团化带来的浸润性提高和引入的赝电容。     

High mechanical performance based on the alignment of cellulose nanocrystal/chitosan composite filaments through continuous coaxial wet spinning

Cellulose nanocrystals (CNCs) with high crystallinity exhibit high mechanical stiffness and strength. However, the high dispersibility of CNCs results in limited spinnability and orientation. In this study, oxidized nanocellulose was selected to obtain regionally oxidized CNCs (RO-CNC) with carboxyl groups appended. For the formation of orientable and extensible RO-CNC filaments, chitosan was introduced as the sheath solution to induce orientation by electrostatic action. The chemical structures were analyzed by Fourier transform infrared spectroscopy. The morphology of the oriented CNCs filaments was characterized by scanning electron microscopy and wide-angle X-ray scattering. Analysis of the relationship between the mechanical strength and the CNCs directional arrangement revealed that the mechanical strength of the composite fibers increased with the injection speed ratio as a result of the orientation of the RO-CNC. The mechanical strength of the oriented reinforced composite filaments reached as high as 104 MPa with an orientation index of 0.73. The tensile strength and elastic modulus of the filaments increased by 33% and 20%, respectively, compared to the unmodified CNCs spun fiber.

Graphic abstract

     

Structure and properties of polyimide aerogels with different skeleton flexibilities

ABSTRACT

In order to better understand the influences of polyimide (PI) skeleton structure and freeze-drying process on the properties of PI aerogel materials, PI molecular chains (ODPA-ODA, BPDA-ODA, BPDA-PPDA) with different stiffnesses and flexibilities were designed and a series of PI aerogels were accordingly fabricated by freeze-drying technique. The aerogels produced featured light weight (density of 0.01–0.16 g/cm³) and high flexibility, and their density, pore structure, and compress recovery performance could be well controlled by delicately tuning the molecular chain structure and solid contents of the poly (amic acid) salt solution. In addition, a hard PI aerogel with enhanced compressive strength was obtained by quick-freezing in liquid nitrogen.     

Flexible,fatigue resistant,and heat-insulated nanofiber-assembled polyimide aerogels with multifunctionality

Ultralight flexible polymers enable promising application in many fields but are often hindered by low reusability with fatigue failure, weak mechanical stability and low temperature resistance. Here, superelastic polyimide nanofiber aerogels (PNFAs) with high hydrophobicity have been prepared by utilizing the polyamic acid (PAA) nanofibers to construct a continuous and isotropic fibrous architecture. “Fiber-bonding” effect is designed to endow the PNFAs with the structure-derived superelasticity. The results demonstrate that the PNFAs possess ultralight densities (9.7–19.1 mg cm⁻³), excellent absorption capacity (58 times for n-hexane), broad working-temperature range, high resilience after 1000 fatigue cycles at 60% strain, and outstanding thermal insulation performance. Analysis of 50 absorption-harvesting cycle tests reveals that these highly hydrophobic PNFAs possess an ultrahigh reusability. The compressed PNFAs return to their original shape after they are distilled to recover the absorbed pollutants. These PNFAs with high absorption capacity and robust mechanical stability are promising to be applied in a variety of industrial and environmental applications.     

Flow‐Injection Pulsed‐Amperometric Determination of Free Glycerol in Biodiesel at a Gold Electrode

This work reports the highly‐sensitive amperometric determination of free glycerol in biodiesel at a gold electrode adapted in a flow‐injection analysis (FIA) cell. The amperometric method involved the continuous application of three sequential pulses to the working electrode (+250 mV, +700 mV, and ?200 mV, for 100 ms each). This sequence of potential pulses eliminated electrode passivation and dramatically increased the analytical signal. The proposed FIA‐amperometric method presented low relative standard deviation between injections (1.5 %, n=15), high analytical frequency (85 h^?1), satisfactory recovery values (93–118 %) for spiked samples, wide linear range (from 1 to 300 µmol L^?1), and low detection limit (0.5 µmol L^?1).     

Removal of Arsenazo-III from liquid radioactive waste by cloud point extraction

Optimization of a method, based on thermal oxidation using a tube furnace system (Pyrolyser), for the separation of organically bound tritium (OBT) from environmental matrices is discussed. Results show that a maximum of ~?4 g of the vegetation sample, typical wild plant leaves of tropical regions, and ~?8 g of sediment sample can be combusted efficiently in the pyrolyser system. The recovery of OBT from wheat sample was observed to be ~?92% and that for sediment sample was ~?88%. The minimum detectable activity (MDA) at 95% confidence level was 3.4 Bq kg^?1 for a sample weight?=?4 g, counting time?=?30,000 s, and detection efficiency?=?23%.

     

Cellulose nanocrystal extraction from rice straw using a chlorine-free bleaching process

Cellulose nanocrystals (CNCs) have attracted tremendous attention because of their excellent chemical and physical properties and due to their renewability and sustainability. This material can be extracted from agricultural by-products such as rice straw, banana tree, or bagasse. Rice straw was selected as the raw material in this study. Initially, a large amount of lignin must be removed by an alkaline process to obtain a slurry. Thereafter, a green bleaching process can be used to remove the remaining lignin in the slurry. An UV-emitting diode with 365 nm wavelength assisted the oxidation reaction of the H₂O₂ solution without the use of chlorine-containing chemical bleach. The reaction required only 2.5 h to obtain high-purity cellulose and successfully enhanced the yield. Transmission electron microscopy images showed that the CNCs from rice straw were?~?100 nm long and 10–15 nm wide. The crystalline index and degradation temperature of CNCs were 83.8% and 257 °C, respectively.

     

Acryloyl-modified cellulose nanocrystals: effects of substitution on crystallinity and copolymerization with acrylic monomers

Cellulose nanocrystals (CNCs) are crystalline nano-rods that have high specific strength with hydroxyl surface chemistry. A wide range of chemical modifications have been performed on the surface of CNCs to increase their potential to be used in applications where compatibilization with other materials is required. Understanding the surface chemistry of CNCs and critically examining the functionalization technique are crucial to enable control over the extent of modification and the properties of CNCs. This work aims to optimize the surface modification of wood-derived CNCs with isocyanatoethyl methacrylate (IEM), a bifunctional molecule carrying both isocyanate and vinyl functional groups. We studied the effect of modification reaction time and temperature on the degree of substitution, crystallinity, and morphology of the CNCs. We found that the degree of modification is a strong and increasing function of reaction temperature over the range studied. However, the highest temperature (65 °C) and the longest time of reaction (6 h) resulted in shorter, thinner, and less crystalline CNCs. We obtained surface hydroxyl conversion of 60.1?±?6% and percent crystallinity of 84% by keeping the reaction shorter (30 min) at 65 ºC. Also, the copolymerization ability of modified CNCs was verified by polymerizing attached IEM groups with acrylic monomers via solution polymerization. The polymer-grafted CNCs (6% w/w) dispersed better in an acrylic polymer matrix compared to unmodified CNCs (umCNCs), resulting in approximately 100% improvement in the tensile strength and about 53% enhancement in the hardness of the acrylic, whereas addition of 6% w/w umCNCs did not influence the strength and hardness.

Graphic abstract

     

Hydrogen and Methane Production, Energy Recovery, and Organic Matter Removal from Effluents in a Two-Stage Fermentative Process

This study evaluates the potential for using different effluents for simultaneous H₂ and CH₄ production in a two-stage batch fermentation process with mixed microflora. An appreciable amount of H₂ was produced from parboiled rice wastewater (23.9?mL g^?1 chemical oxygen demand [COD]) and vinasse (20.8?mL g^?1 COD), while other effluents supported CH₄ generation. The amount of CH₄ produced was minimum for sewage (46.3?mL g^?1 COD), followed by parboiled rice wastewater (115.5?mL g^?1 COD) and glycerol (180.1?mL g^?1 COD). The maximum amount of CH₄ was observed for vinasse (255.4?mL g^?1 COD). The total energy recovery from vinasse (10.4?kJ g^?1 COD) corresponded to the maximum COD reduction (74.7?%), followed by glycerol (70.38?%, 7.20?kJ g^?1 COD), parboiled rice wastewater (63.91?%, 4.92?kJ g^?1 COD), and sewage (51.11?%, 1.85?kJ g^?1 COD). The relatively high performance of vinasse in such comparisons could be attributed to the elevated concentrations of macronutrients contained in raw vinasse. The observations are based on kinetic parameters of H₂ and CH₄ production and global energy recovery of the process. These observations collectively suggest that organic-rich effluents can be deployed for energy recovery with sequential generation of H₂ and CH₄.     

Manganese Oxide/Graphene Aerogel Composites as an Outstanding Supercapacitor Electrode Material

Graphene aerogels (GA), prepared with an organic sol–gel process, possessing a high specific surface area of 793 m² g^?1, a high pore volume of 3 cm³ g^?1, and a large average pore size of 17 nm, were applied as a support for manganese oxide for supercapacitor applications. The manganese oxide was electrochemically deposited into the highly porous GA to form MnO₂/GA composites. The composites, at a high manganese oxide loading of 61 wt. %, exhibited a high specific capacitance of 410 F g^?1 at 2 mV s^?1. More importantly, the high rate specific capacitances measured at 1000 mV s^?1 for these composites were two‐fold higher than those obtained with samples prepared in the absence of the GA support. The specific capacitance retention ratio, based on the specific capacitance obtained at 25 mV s^?1, was maintained high, at 85 %, even at the high scan rate of 1000 mV s^?1, in contrast with the significantly lower value of 67 % for the plain manganese oxide sample. For the cycling stability, the specific capacitance of the composite electrode decayed by only 5 % after 50,000 cycles at 1000 mV s^?1. The success of this MnO₂/GA composite may be attributed to the structural advantages of high specific surface areas, high pore volumes, large pore sizes, and three‐dimensionally well‐connected network of the GA support. These structural advantages made possible the high mass loading of the active material, manganese oxide, large amounts of electroactive surfaces for the superficial redox events, fast mass‐transfer within the porous structure, and well‐connected conductive paths for the involved charge transport.     

Ultralight,High Capacitance,Mechanically Strong Graphene-Cellulose Aerogels

With increasing energy demand driving the need for eco-friendly and efficient energy storage technology, supercapacitors are becoming increasingly prevalent in wearable devices because of their portability and stability. The performance of these supercapacitors is highly dependent on the choice of electrode material. The high capacitance and mechanical properties needed for these materials can be achieved by combining graphene’s stable electrical properties with renewable cellulose’s excellent mechanical properties into porous aerogels. In this study, graphene-cellulose hydrogels were prepared by a one-step hydrothermal method, with porous, ultra-light, and mechanically strong graphene-cellulose aerogels then prepared by freeze-drying. These composite aerogels possess excellent mechanical strength and high specific capacitance, capable of bearing about 1095 times the pressure of their own weight. Electrochemical tests show the specific capacitance of these composite aerogels can reach 202 F/g at a scanning rate of 5 mA/cm². In view of their high surface area and fast charge transport provided by their 3D porous structure, graphene-cellulose aerogels have great potential as sustainable supercapacitor electrodes.     

Conventional and microwave synthesis of mesoporous calcium titanate nanopowders: a comparative study

Since the late 1960s, ceric hydrogen phosphates have attracted the attention of scientists due to remarkable ion exchange, sorption, proton-conduction and catalytic properties. In this work, through the application of various solvents, we, for the first time, have obtained monolithic aerogels based on ceric hydrogen phosphates with high porosity (~99%) and extremely low density (~10?μg/cm³). The composition and structure of aerogels were thoroughly studied with XRD, TEM, SEM, XPS, low temperature nitrogen adsorption methods, TGA/DSC, Fourier-transform infrared spectroscopy (FTIR) and small-angle neutron scattering (SANS). The aerogels were found to belong to the fibrous macroporous aerogels family.

Open image in new window

     

Hydrophobic and Physical Properties of the Two Step Processed Ambient Pressure Dried Silica Aerogels with Various Exchanging Solvents

The experimental results by using various exchanging solvents in the preparation of two step (acid and base) processed ambient pressure dried hydrophobic silica aerogels, are reported. Silica alcogels were prepared by hydrolysis with oxalic acid and condensation with NH₄OH of ethanol diluted tetraethylorthosilicate (TEOS) precursor and hexamethyldisilazane(HMDZ) methylating agent. The exchanging solvents used were: hexane, cyclohexane, heptane, benzene, toluene and xylene. The physical properties such as % of volume shrinkage, density, pore volume, % of porosity, thermal conductivity, % of optical transmission, surface area, pore size distribution and contact angle (θ) of the silica aerogels with water, were measured as a function of EtOH/TEOS molar ratios (R) for all the exchanging solvents. It was found that the physical and hydrophobic properties of the silica aerogels strongly depend on the nature of the solvent and R. Heptane solvent resulted in highly transparent (≈90% optical transmission at 700 nm for 1 cm thick sample), low density (≈0.060 g/cm³), low thermal conductive (≈0.070 W/m·K), high % of porosity (97%), high surface area (750 m²/g), uniform porosity and hydrophobic (θ ≈ 160°) aerogels compared to other solvents. On the otherhand, xylene resulted in aerogels with higher hydrophobicity (θ ≈ 172°) among other solvents.     

A Petrochemical-Free Route to Superelastic Hierarchical Cellulose Aerogel

Cellulose aerogels are plagued by intermolecular hydrogen bond-induced structural plasticity, otherwise rely on chemicals modification to extend service life. Here, we demonstrate a petrochemical-free strategy to fabricate superelastic cellulose aerogels by designing hierarchical structures at multi scales. Oriented channels consolidate the whole architecture. Porous walls of dehydrated cellulose derived from thermal etching not only exhibit decreased rigidity and stickiness, but also guide the microscopic deformation and mitigate localized large strain, preventing structural collapse. The aerogels show exceptional stability, including temperature-invariant elasticity, fatigue resistance (∼5 % plastic deformation after 10⁵ cycles), high angular recovery speed (1475.4° s⁻¹), outperforming most cellulose-based aerogels. This benign strategy retains the biosafety of biomass and provides an alternative filter material for health-related applications, such as face masks and air purification.     

Simultaneous sensing of L-tyrosine and epinephrine using a glassy carbon electrode modified with nafion and CeO2 nanoparticles

An electrochemical sensor was developed and tested for detection of L-tyrosine in the presence of epinephrine by surface modification of a glassy carbon electrode (GCE) with Nafion and cerium dioxide nanoparticles. Fabrication parameters of a surfactant-assisted precipitation method were optimized to produce 2–3 nm CeO₂ nanoparticles with very high surface-to-volume ratio. The resulting nanocrystals were characterized structurally and morphologically by X-ray diffractometery (XRD), scanning and high resolution transmission electron microscopy (SEM and HR-TEM). The nanopowder is sonochemically dispersed in a Nafion solution which is then used to modify the surface of a GCE electrode. The electrochemical activity of L-tyrosine and epinephrine was investigated using both a Nafion-CeO₂ coated and a bare GCE. The modified electrode exhibits a significant electrochemical oxidation effect of L-tyrosine in a 0.2 M Britton-Robinson (B-R) buffer solution of pH 2. The electro-oxidation peak current increases linearly with the L-tyrosine concentration in the molar concentration range of 2 to 160 μM. By employing differential pulse voltammetry (DPV) for simultaneous measurements, we detected two reproducible peaks for L-tyrosine and epinephrine in the same solution with a peak separation of about 443 mV. The detection limit of the sensor (signal to noise ratio of 3) for L-tyrosine is ~90 nM and the sensitivity is 0.20 μA μM⁻¹, while for epinephrine these values are ~60 nM and 0.19 μA μM⁻¹. The sensor exhibited excellent selectivity, sensitivity, reproducibility and stability as well as a very good recovery time in real human blood serum samples.

Simultaneous electrochemical determination of L-tyrosine and epinephrine in blood plasma with Nafion-CeO₂/GCE modified electrode showing a 443 mV peak-to-peak potential difference between species oxidation peak currents.

     

Cyclodextrin Bonded Phase for Liquid Chromatographic Separation and Analysis of Some Oral Contraceptives

Abstract

A specific and sensitive analytical HPLC procedure was described for quantitative determination of ethinylestradiol and norethisterone acetate (Anovlar 1) and ethinylestradiol and norgestrel (Primovlar) in tablet formulation. These steroids were extracted from the tablets with methanol. The steroids were then determined with high performance liquid Chromatograph-Cyclobond 1 column using mobile phase phosphate buffer pH 7.0: methanol (60:40), flow rate 0.5 ml min^?1 and the detection was effected spectrophotometrically at 280 nm, using variable wavelength UV detector.

There was > 99.3% recovery from synthetic mixtures and the coefficient of variation was < 2.0% for the formulations investigated. The method is highly quantitative and reproducible.     

Influence of thermal process on microstructural and physical properties of ambient pressure dried hydrophobic silica aerogel monoliths

The experimental results of thermal process on the microstructural and physical properties of ambient pressure dried hydrophobic silica aerogel monoliths are reported and discussed. With sodium silicate as precursor, ethanol/hexamethyldisiloxane/hydrochloric acid as surface modification agent, the crack-free and high hydrophobic silica aerogel monoliths was obtained possessing the properties as low density (0.096 g/cm³), high surface area (651 m²/g), high hydrophobicity (~147°) and low thermal conductivity (0.0217 Wm/K). Silica aerogels maintained hydrophobic behavior up to 430 °C. After a thermal process changing from room temperature to 300 °C, the hydrophobicity remained unchanged (~128°), of which the porosity was 95.69% and specific density about 0.094 g/cm³. After high temperature treatment (300–500 °C), the density of final product decreased from 0.094 to 0.089 g/cm³ and porosity increased to 96.33%. With surface area of 466 m²/g, porosity of 91.21% and density about 0.113 g/cm³, silica aerogels were at a good state at 800 °C. Thermal conductivities at desired temperatures were analyzed by the transient plane heat source method. Thermal conductivity coefficients of silica aerogel monoliths changed from 0.0217 to 0.0981 Wm/K as temperature increased to 800 °C, revealed an excellent heat insulation effect during thermal process.