High-Pressure Annealing Effect on Glass Transformation Temperature of Zr41Ti14Cu12.5Ni10Be22.5 Bulk Metallic Glass

Zr41 Ti14 Cu12.5Ni10Be22.5 bulk metallic glasses （BMG） are annealed at a temperature of 603 K under ambient and high pressures in the range of 3-6 GPa. The effect of high pressure annealing on the nanocrystallization process of compressed specimens is investigated by x-ray diffraction, differential scanning calorimetry and transmission electron microscopy. Experimental results show that the grain size of the crystalline phase decreases with the increasing pressure. For the Zr41Ti14Cu12.5Nil0Be22.5 BMG annealing at 603K in the pressure range of 0- 6 GPa, the activation energy 159.68 kJ/mol and the activation volume △V＊ =0.94 cm^3/mol are determined. The mechanism for the effects of the high pressure on the nanocrystallization process of the BMG is discussed.     

Kinetics of the glass Transition of the Zr41Ti14Cu12.5Ni10Be22.5 Alloy Solidified in a Drop Tube

Droplets of Zr41Ti14Cu12.5Ni10Be22.5 glass-forming alloy with different sizes are solidified in a drop tube containerless process.The glass transition temperature Tg of Zr41Ti14Cu12.5Ni10Be22.5 glassy spheres solidified with different cooling rates is investigated by using a differential scanning calorimeter.It was found that all the amor phous spheres show an increase of Tg with the heating rate.The glassy spheres have a unique value for the glass transition activation energy Eg=435.50kJ/mol,which is independent of cooling rate q.The insensitivity of Tg to q is interpreted by an extension of the free volume model for flow.     

Energy model for the Zr-based metallic glass alloy melt with clusters

An energy model for the melt of bulk metallic glass (BMG) with clusters was established, the Gibbs free energy and interfacial energy for the Zr-Al-Ni ternary alloy melt with Zr2Ni clusters were calculated, and the effects of the clusters on the Gibbs free energy, interfacial energy and nucleation rate were analyzed. The results showed that the existence of the clusters in the Zr-Al-Ni ternary alloy melt enables the Gibbs free energy to decrease in the composition range where bulk metallic glass forms easily, makes the interfacial energy increase and changes the distribution of the interfacial energy with the alloy composition. Because of the clusters in the melt, the Gibbs free energy of the Zr66Al8Ni26 alloy melt decreases about 0.3-1 kJ/mol and the interfacial energy between the melt and crystal nucleus increases about 0.016 J/m2. The nucleation rate of the undercooled Zr66Al8Ni26 alloy melt decreases evidently under the influence of the clusters on Gibbs free energy and the interfacial energy, and the maximum of the nucleation rate in the melt with the Zr2Ni clusters is only about 107 mol-1·s-1.     

Crystallization of the Amorphous Zr70Cu20Ni10Alloy

Crystallization Behaviour of the amorphous Zr70Cu20Ni10 alloy within the supercooled liquid region has been investigated by means of differential scanning calorimetry(DSC) and transmission electron microscopy(TEM).It is found that the relationship between the incubation time,which is necessary for the amorphous Zr70Cu20Ni10 alloy to nucleate and grow,and the annealing temperature obeys an exponential function.A similar relationship can also be observed between the peak time corresponding to the minimum of the exothermic reaction in the DSC scan and the annealing temperature,TEM observations confirm that the first exothermic peak in the DSC trace of amorphous Zr70Cu20Ni10 alloy mainly corresponds to the precipitation of the Zr2Cu phase,while the second peak mainly corresponds to the precipitation of the nanoscale Zr2Ni phase.     

Microstructure evolution of zircaloy-4 during Ne ion irradiation and annealing: An in situ TEM investigation

The microstructural evolution of zircaloy-4 was studied, including the amorphization and recrystallization of Zr（Fe, Cr）2 precipitates, and the density of dislocations under in situ Ne ion irradiation and post annealing. The results show that irradiation at a relatively high temperature and dose induces the formation of nanocrystals in pre-amorphized Zr（Fe, Cr）2 precipitates. The recrystallized nanocrystals also have the structure of hcp-Zr（Fe, Cr）2. The formation of the nanocrystals is thought to be the consequence of competition between atomistic disordering and the recrystallization of precipitates under ion irradiation. The free energy of the nanocrystal is lower than that of the amorphous state, which is another reason for the recrystallization of the precipitates. With increased annealing temperature, the density of the nanocrystals is increased. The dislocation density sharply decreases with the increase in the annealing temperature, and its size increases.     

Effect of microstructure on the thermoelectric properties of CSD-grown Bi2Sr2Co2Oy thin films

Three Bi2Sr2Co2Oy thin films with different microstructures have been prepared by chemical solution deposition on LaAlO 3(001) through varying the annealing temperature.With the decrease in the annealing temperature,both the size and c-axis alignment degree of grains in the film decrease as well,leading to an increase in the film resistivity.In addition,the decrease in the annealing temperature also results in a slight increase in the Seebeck coefficient due to the enhanced energy filtering effect of the small-grain film.The nanostructured Bi2Sr2Co2Oy film with an average grain size of about 100 nm shows a power factor comparable to that of films with larger grains.Since the thermal conductivity of the nanostructured films can be depressed due to the enhanced phonon scattering by grain boundary,a higher figure of merit is expected in Bi2Sr2Co2Oy thin film with grains in nanometer size.     

Structural Characteristics of Cerium Oxide Nanocrystals Prepared by the Microemulsion Method

The aim of this work is to investigate the microstructure development of erium oxide nanocrystal,prepared by the microemulsion process,as a function of annealing temperature in air.Combined with the HRTEM and the thermogravimetric-differential thermal analysis in air.Combined withthe HRTEm and the thremogravimetric-differential thermal analysis(TG-DTA),the XRD patterns reveal that the sample annealed at 623 K is amorphous,and the formation of cerium oxide nanocrystal occurs above 773 K.The local structural and electronic properties in the nanocrystallization process are probed by X-ray absorption spectra (XAS) at the Ce L3 edge.It is found that the phase structure changes from triclinic to cubic (CeO2),and the electroic structure changes from Ce^3 to Ce^4 upon increasing the annealing temperature.     

The effect of interfacial energy anisotropy on planar interface instability in a succinonitrile alloy under a small temperature gradient

The morphological stability of a planar interface with different crystallographic orientations is studied under a small positive temperature gradient using a transparent model alloy of succinonitrile.Novel experimental apparatus is constructed to provide a temperature gradient of about 0.37 K/mm.Under this small temperature gradient,the planar interface instability depends largely on the crystallographic orientation.It is shown experimentally that the effect of interfacial energy anisotropy on planar interface stability cannot be neglected even in a small temperature gradient system.Higher interfacial energy anisotropy leads the planar interface to become more unstable,which is different from the stabilizing effect of the interfacial energy on the planar interface.The experimental results are in agreement with previous theoretical calculations and phase field simulations.     

Internal friction behavior of Zr59Fe18Al10Ni10Nb3metallic glass under different aging temperatures

We investigate the role of aging temperature on relaxation of internal friction in Zr₅₉Fe₁₈Al₁₀Ni₁₀Nb₃metallic glass.For this purpose,dynamic mechanical analysis with different annealing temperatures and frequency values is applied.The results indicate that the aging process leads to decrease in the dissipated energy in the temperature range of glass transition.It is also found that the increase in applied frequency weakens the loss factor intensity in the metallic glass.Moreover,the Kohlrausch-Williams-Watts(KWW)equation is used to evaluate the evolution of internal friction during the aging process.According to the results,higher annealing temperature will make the primary internal friction in the material increase;however,a sharp decline is observed with the time.The drop in characteristic time of internal friction is also closely correlated to the rate of atomic rearrangement under the dynamic excitation so that at higher annealing temperatures,the driving force for the collaborative movement of atoms is easily provided and the mean relaxation time significantly decreases.     

Photoluminescence of Mg—doped GaN with Different Mg Concentrations after Annealing at Different Temperatures

The blue band (BB) in low temperature photoluminescence of Mg-doped GaN films with different Mg concentrations is investigated.The BB peak of as-grown samples with higher Mg concentration centres at lower energy.A shift of the BB peak energy is observed after annealing in N2 at different temperatures,meanwhile,the difference between the BB peak energy is observed after annealing in N2 at different temperatures.Meanwhile,the difference between the BB peak energies diminishes for raised annealing temperature,and the BB peaks for different samples converge to 2.92eV after annealing at 850℃.These experimental results can be accounted for by a model based on compensation effect.The shift of BB lines provides a useful criterion for the optimum annealing temperature of the Mg-doped GaN material,and the value is taken to be 850℃ in our case.     

A possible experimental observable for the determination of neutron skin thickness

The dependence between neutron skin thickness and neutron abrasion cross section （σnabr） for neutron-rich nuclei is investigated within the framework of the statistical abrasion ablation model. Assuming that the density distributions for proton and neutron are of Fermi-type, and adjusting the diffuseness parameter of neutron density distribution in the droplet model, we find out the good linear correlation between the neutron skin thickness and the abrasion cross section σnabr for neutron-rich nuclei. The uncertainty of neutron skin thickness determined from σnabr is very small. It is suggested that σnabr can be used as a new experimental observable to extract the neutron skin thickness for neutronrich nucleus. The scaling behaviours between neutron skin thickness and σnabr, separately, for isotopes of ^26-35Na, ^44-56Ar, ^48-60Ca, ^67-78Ni are also investigated.     

Kiselev黑洞的热力学性质和物质吸积特性

本文考虑带有黑洞视界和宇宙视界的Kiselev时空.研究以黑洞视界和宇宙视界为边界的系统的热力学性质.统一地给出了两个系统的热力学第一定律;在黑洞视界半径远小于宇宙视界半径的情况下,近似地计算了通过宇宙视界和黑洞视界的热能.然后,探讨Kiselev时空的物质吸积特性.在吸积能量密度正比于背景能量密度的条件下给出黑洞的吸积率,讨论了黑洞吸积率与暗能量态方程参数的关系.     

Electron tunnelling phase time and dwell time through an associated delta potential barrier

The electron tunnelling phase time τP and dwell time τD through an associated delta potential barrier U(x) = ξδ(x) are calculated and both are in the order of 10^-17～10^-16s. The results show that the dependence of the phase time on the delta barrier parameter ξ can be described by the characteristic length lc = h^2/meξ and the characteristic energy Ec=meξ^2/h^2 of the delta barrier, where me is the electron mass, lc and Ec are assumed to be the effective width and height of the delta barrier with lcEc=ξ, respectively. It is found that TD reaches its maximum and τD = τp as the energy of the tunnelling electron is equal to Ec/2, i.e. as lc =λDB, λDB is de Broglie wave length of the electron.     

Critical radius and dipole polarizability for a confined system

The analytical transfer matrix method (ATMM) is applied to calculating the critical radius $r_{\rm c}$ and the dipole polarizability $\alpha_{\rm d}$ in two confined systems: the hydrogen atom and the Hulth\'{e}n potential. We find that there exists a linear relation between $r_{\rm c}^{1/2}$ and the quantum number $n_{r}$ for a fixed angular quantum number $l$, moreover, the three bounds of $\alpha_{\rm d}$ ($\alpha_{\rm d}^{K}$, $\alpha_{\rm d}^{B}$, $\alpha_{\rm d}^{U}$) satisfy an inequality: $\alpha_{\rm d}^{K}\leq\alpha_{\rm d}^{B}\leq\alpha_{\rm d}^{U}$. A comparison between the ATMM, the exact numerical analysis, and the variational wavefunctions shows that our method works very well in the systems.     

The influence of collision energy on magnetically tuned 6Li-6Li Feshbach resonance

The effect of collision energy on the magnetically tuned $^{6}$Li-$^{6}$Li Feshbach resonance (FR) is investigated theoretically by using the coupled-channel (CC) method for the collision energy ranging from 1 μ$ {\rm K} \cdot {k}_{\rm B}$ to 100 μ$ {\rm K} \cdot {k}_{\rm B}$. At the collision energy of 1 μ$ {\rm K} \cdot {k}_{\rm B}$, the resonance positions calculated are 543.152 Gs (s wave, the unit $1 {\rm Gs}=10^{-4} {\rm T}$), 185.109 Gs (p wave $|m_{l}| = 0$), and 185.113 Gs (p wave $|m_{l}| = 1$), respectively. The p-wave FR near 185 Gs exibits a doublet structure of 4 mGs, associated with dipole-dipole interaction. With the increase of the collision energy, it is found that the splitting width remains the same (4 mGs), and that the resonance positions of s and p waves are shifted to higher magnetic fields with the increase of collision energy. The variations of the other quantities including the resonance width and the amplitude of the total scattering section are also discussed in detail. The thermally averaged elastic rate coefficients at $T=10$, 15, 20, 25 K are calculated and compared.     

Observation of four-wave mixing in caesium atoms using a noncycling transition

In this paper the generation of four-wave mixing (FWM) signal using a noncycling transition of caesium atoms is investigated when the pumping laser is locked to the transition $6{\rm S}_{1/2}F=4\to6{\rm P}_{3/2}F'=4$, and meanwhile the probe frequency is scanned across the $6{\rm S}_{1/2}F=4 \to6{\rm P}_{3/2}$ transition. The efficiency of the four-wave mixing signal as a function of the intensity of the pumping beams and the detuning of the pumping beams is also studied. In order to increase the detection efficiency, a repumping laser which is resonant with $6{\rm S}_{1/2} F=3\to 6{\rm P}_{3/2}F'=4$ transition is used. A theoretical model is also introduced, and the theoretical results are in qualitative agreement with experimental ones.     

Novel material for nonvolatile ovonic unified memory (OUM)－Ag11In12Te26Sb51 phase change semiconductor

In this paper, Ag_{11}In_{12}Te_{26}Sb_{51} phase change semiconductor films have been prepared by dc sputtering. The crystallization behaviour of amorphous Ag_{11}In_{12}Te_{26}Sb_{51} thin films was investigated by using differential scanning calorimetry and x-ray diffraction. It was found that the crystallization temperature is about 483K and the melting temperature is 754.8K and the activation energy for crystallization, E_a, is 2.07eV. The crystalline Ag_{11}In_{12}Te_{26}Sb_{51} films were obtained using initializer. The initialization conditions have a great effect on the sheet resistance of Ag_{11}In_{12}Te_{26}Sb_{51} films. We found that the effect of the initialization condition on the sheet resistance can be ascribed to the crystallinity of Ag_{11}In_{12}Te_{26}Sb_{51} films. The sheet resistance of the amorphous (R_{amo}) film is found to be larger than 1×10^6Ω and that of the crystalline (R_{cry}) film lies in the range from about 10^3 to 10^4Ω. So we have the ratio R_{amo}/R_{cry}=10^2～10^3, which is sufficiently large for application in memory devices.     

A simulation study of microstructure evolution during solidification process of liquid metal Ni

A molecular dynamics simulation study has been performed for the microstructure evolution in a liquid metal Ni system during crystallization process at two cooling rates by adopting the embedded atom method (EAM) model potential. The bond-type index method of Honeycutt--Andersen (HA) and a new cluster-type index method (CTIM-2) have been used to detect and analyse the microstructures in this system. It is demonstrated that the cooling rate plays a critical role in the microstructure evolution: below the crystallization temperature $T_{\rm c}$, the effects of cooling rate are very remarkable and can be fully displayed. At different cooling rates of $2.0\times10^{13}$\,K\,$\cdot$\,s$^{-1}$ and $1.0\times10^{12}$\,K\,$\cdot$\,s$^{-1}$, two different kinds of crystal structures are obtained in the system. The first one is the coexistence of the hcp (expressed by (12 0 0 0 6 6) in CTIM-2) and the fcc (12 0 0 0 12 0) basic clusters consisting of 1421 and 1422 bond-types, and the hcp basic cluster becomes the dominant one with decreasing temperature, the second one is mainly the fcc (12 0 0 0 12 0) basic clusters consisting of 1421 bond-type, and their crystallization temperatures $T_{\rm c}$ would be 1073 and 1173\,K, respectively.     

Co-Al-W基高温合金的团簇成分式

Co-Al-W基高温合金具有类似于Ni基高温合金的γ+γ'相组织结构.根据面心立方固溶体的团簇加连接原子结构模型,Ni基高温合金的成分式即最稳定的化学近程序结构单元可以描述为第一近邻配位多面体团簇加上次近邻的三个连接原子.本文应用类似方法,首次给出了Co-Al-W基高温合金的团簇成分式.利用原子半径和团簇共振模型,可计算出Co-Al-W三元合金的团簇成分通式,为[Al-Co_(12)](Co,Al,W)_3,即以Al为中心原子、Co为壳层原子的[Al-Co_(12)]团簇加上三个连接原子.对于多元合金,需要先将元素进行分类:溶剂元素——类Co元素Co (Co, Cr, Fe, Re, Ni,Ir,Ru)和溶质元素——类Al元素Al (Al,W,Mo, Ta,Ti,Nb,V等);进而根据合金元素的配分行为,将类Co元素分为Co~γ(Cr, Fe, Re)和Co~(γ')(Ni, Ir, Ru);根据混合焓,将类Al元素分为Al, W (W, Mo)和Ta (Ta, Ti, Nb, V等).由此,任何多元Co-Al-W基高温合金均可简化为Co-Al伪二元体系或者Co-Al-(W,Ta)伪三元体系,其团簇加连接原子成分式为[Al-Co_(12)](Co_(1.0)Al_(2.0))(或[Al-Co_(12)] Co_(1.0)Al_(0.5)(W,Ta)_(1.5)=Co_(81.250)Al_(9.375)(W,Ta)_(9.375) at.%).其中,γ与γ'相的团簇成分式分别为[Al-Co_(12)](Co_(1.5)Al_(1.5))(或[Al-Co_(12)] Co_(1.5)Al_(0.5)(W,Ta)_(1.0)=Co_(84.375)Al_(9.375)(W,Ta)_(6.250) at.%)和[Al-Co_(12)](Co_(0.5)Al_(2.5))(或[Al-Co_(12)] Co_(0.5)Al_(0.5)(W, Ta)_(2.0)=Co_(78.125)Al_(9.375)(W,Ta)_(12.500)at.%).例如,Co_(82)Al_9W_9合金的团簇成分式为[Al-Co_(12)]Co_(1.1)Al_(0.4)W_(1.4)(～[Al-Co_(12)]Co_(1.0)Al_(0.5)W_(1.5)),其中γ相的团簇成分式为[Al-Co_(12)]Co_(1.6)Al_(0.4)W_(1.0)(～[Al-Co_(12)]Co_(1.5)Al_(0.5)W_(1.0)),γ'相的团簇成分式为[Al-Co_(12)]Co_(0.3)Al_(0.5)W_(2.2)(～[AlCo_(12)]Co_(0.5)Al_(0.5)W_(2.0)).     

Incommensurate-commensurate magnetic phase transition in double tungstate Li2Co(WO4)2

Magnetic susceptibility, specific heat, and neutron powder diffraction measurements have been performed on polycrystalline Li$_{2}$Co(WO$_{4}$)$_{2}$ samples. Under zero magnetic field, two successive magnetic transitions at $T_{\rm N1}\sim 9.4$ K and $T_{\rm N2}\sim 7.4$ K are observed. The magnetic ordering temperatures gradually decrease as the magnetic field increases. Neutron diffraction reveals that Li$_{2}$Co(WO$_{4}$)$_{2}$ enters an incommensurate magnetic state with a temperature dependent $\bm k$ between $T_{\rm N1}$ and $T_{\rm N2}$. The magnetic propagation vector locks-in to a commensurate value $\bm k = (1/2, 1/4, 1/4)$ below $T_{\rm N2}$. The antiferromagnetic structure is refined at 1.7 K with Co$^{2+}$ magnetic moment 2.8(1) $\mu_{\rm B}$, consistent with our first-principles calculations.