Performance evaluation of path-averaged soliton pulses in loss-managed 10-Gbps soliton transmission link over a long haul

In this paper, the performance evaluation of path-averaged soliton transmission link for various performance measures viz. OSNR, optical power, extinction ratio, bit error rate (BER) and Q factor at different levels of noise figure and values of pulse width (FWHM) has been carried out. The performance of soliton transmission link is studied, taking into account soliton interaction, amplified spontaneous emission (ASE) noise and noise figure. The model presented considers interaction in a random sequence of solitons and the effect of the ASE noise added in each amplification stage. The influence of ASE noise, noise figure and pulse width with different amplifier spacing on the BER and quality factor has been investigated. It has been shown that these play dominant roles in degrading the performance measures. We have demonstrated the capability of path-averaged (guiding-centre) soliton for a long-haul distance of 17,000 km at a bit rate of 10 Gbps without ASE effect and noise figure in each amplifier span length of 500 km. The average value of quality factor is found to be 16.6 dB and the average BER is of the order of 10⁻¹² over the transmission distance of 17,000 km. Further, it has been investigated that a severe system penalty results on the inclusion of ASE effect and noise figure in order to achieve the same level of performance. Thus, the investigations ascertain that in order to maintain the same level of BER and Q factor, the amplifier spacing and total transmission distance reduce considerably.     

Minimization of self-steepening of ultra short higher-order soliton pulse at 40 Gb/s by the optimization of initial frequency chirp

In this paper, the decay of first- and second-order ultra short pulses of the order of 50 fs due to self-steepening (SS) effect has been numerically investigated for a 40 Gb/s optical soliton system including the impact of third-order dispersion (TOD). It has been observed that the prechirp (both positive and negative) in the pulse can counteract the SS effect and improve compensation performance for the distortions .The critical positive prechirp value is found to be 1.4 and the negative prechirp is 1.2, beyond which the soliton pulse is unstable.     

Effectiveness of electronic equalizer for filter concatenation effect of low-cost 2.5 Gb/s rated DML sources operated at 10 Gb/s

The improvement on the impact of filter concatenation effect on optical signal quality is investigated and discussed for applications in metropolitan optical networks utilizing cost-effective 10-Gb/s transmitters. The sources are low-cost conventional directly modulated lasers (DMLs), fabricated for operation at 2.5 Gb/s but modulated at 10 Gb/s. Performance improvement is achieved by using decision-feedback equalization (DFE) at the receiver end. Experimental studies consider both transient and adiabatic chirp dominated DMLs sources with different chirp characteristics. Measurements have been obtained using a recirculating loop set-up and the performance improvement is evaluated in terms of bit-error-rate (BER) versus number of loops.     

10 and 20 Gb/s all-optical RZ to NRZ modulation format and wavelength converter based on nonlinear optical loop mirror

We present experimental and theoretical results on all-optical 10 and 20 Gb/s RZ to NRZ modulation format and wavelength converter based on a nonlinear optical loop mirror (NOLM). A vector model of converter was developed and the shape of converted pulses was found analytically for particular choice of polarization states. In the experiment, non-zero dispersion shifted fiber with a length 1200 m was used as a nonlinear medium. Pulses from a 10 GHz mode-locked semiconductor laser diode were modulated to form pseudorandom RZ signal and eventually time division multiplexed to 20 Gb/s. RZ pulses were subsequently converted to NRZ signal. The performance of the converter was evaluated experimentally using the data communication analyzer and bit error ratio tester.     

Comparative investigation and suitability of various data formats for 10 Gb/s optical soliton transmission links at different chirps

This paper presents the comparative investigation and suitability of various data formats for optical soliton transmission links at 10 Gb/s for different chirps (−0.7 to 0.7). Here the investigations focused on data formats: NRZ, RZ soliton, RZ raised cosine and RZ super Gaussian. The comparative results and suitability of data formats is based on various performance measures such as Q-factor, eye opening, BER and jitter. It has been indicated that RZ super Gaussian yields the highest value of Q (34.08 dB), good eye opening and lowest BER.     

Transmission performance of 20 × 10 Gb/s WDM signals using cascaded optimized SOAs with OOK and DPSK modulation formats

We investigated 20 channels at 10 Gb/s wavelength division multiplexing (WDM) transmission over 1190 km single mode fiber and dispersion compensating fiber using cascaded inline semiconductor optical amplifier at a span of 70 km for RZ-DPSK (return zero differential phase-shift keying) modulation format by using same channel spacing, i.e. 100 GHz. We show for RZ-OOK (return zero on-off keying) format a transmission distance of up to 1050 km with Q factor more than 15 dB, without any power drops. We developed the SOA model for inline amplifier having minimum cross-talks and ASE (amplified spontaneous emission) noise power with sufficient gain. At optimal bias current of 400 mA, a high constant gain of 36.5 dB is obtained up to a saturation power of 21.36 mW. So reduction of cross-talk and distortion is possible by decreasing the bias current at appropriate amplification factor.The DPSK modulation format has less cross-talk as compared to OOK format for nonlinearities and saturation case. The impact of optical power received and Q factor at different distance for both RZ-OOK and RZ-DPSK modulation format has been illustrated. We have shown the optical spectrum and clear Eye diagram at the transmission distance of 1190 km in RZ-DPSK system and 1050 km in RZ-OOK systems.The bit error rate (BER) for all channels observed is less than 10⁻¹⁰ up to gain saturation for both DPSK and OOK systems. Finally, we investigated that the transmission distance decreases with a decrease in channel spacing of up to 20 GHz.     

Simulation analysis of crosstalk among channels with fiber Raman amplifiers at 10 Gb/s

We have investigated the effects of crosstalk in fiber Raman amplifiers (FRAs) by propagating signals through the Raman fiber. We have observed that quality factor reduces for lesser channel spacing. We have able to propagate the signals in two channels with spacing of 20 GHz and quality factor above 25 dB was obtained. The effect of signal input power and injected pump power on crosstalk and signal interference ratio (SIR) has analyzed. It is observed that the signal gain and the injected pump power should be limited to the value well below the threshold of Raman amplification to ensure small crosstalk and high SIR. The effect of Raman fiber length on crosstalk is also studied and it is observed that for high values of Raman fiber length, SIR reduces considerably.     

Performance analysis of NRZ, RZ, CRZ and CSRZ data formats in 10 Gb/s optical soliton transmission link under the impact of chirp and TOD

This paper presents the performance analysis of non-return-to-zero (NRZ), return-to-zero (RZ), chirped return-to-zero (CRZ) and carrier suppressed return-to-zero (CSRZ) data formats in optical soliton transmission link under the impact of chirp and third-order dispersion (TOD). The performance of these data formats has been analyzed on the basis of certain performance metrics, viz, bit error rate (BER), Q² (dB), OSNR, eye opening, etc. It has been reported here that the performance of CRZ and CSRZ modulation format is better as compared to NRZ and RZ in a soliton transmission link. Further, CSRZ modulation format has been found to deliver optimum performance on the basis of performance evaluation metrics reported in this paper. In case of NRZ and CSRZ, comparatively narrow power spectrum has been observed. Best eye opening, highest value of Q² (dB) of 18 dB and lowest value of BER of the order of 10⁻¹⁶ has been reported in case of CSRZ among the considered data formats. The results have been obtained by varying noise figure from 3.0 to 9.0. No considerable effect of noise was observed. It was observed that at very narrow and ultra short pulse width, OSNR value suffers heavily and reduced to even negative values in dB, thus inducing a high degree of OSNR power penalty. The results were obtained by varying chirp factor from −0.6 to +0.6. Negative chirp resulted in improved OSNR as compared to positive chirp. RZ data format yielded a broader optical spectrum, comparatively low spectral efficiency and poor OSNR thus it was found that RZ format is not suitable for optical soliton transmission under the impact of chirp and TOD.     

Reduction in timing jitter by chirp selection for externally modulated return to zero optical soliton pulse at 10 Gb/s

We investigate the chirp selection of externally modulated RZ soliton pulse at 10 Gb/s for fiber optical communication systems for the reduction in timing jitter. We have chosen single arm Mach-Zehnder amplitude modulator with sin² electrical shaped input-output (P-V) characteristic and its chirp range has been varied in the range of −5 to 5. The timing jitter, Q factor and bit error rate (BER) generated for the chirp range has been studied for various fiber lengths and post compensation has been demonstrated to reduce the timing jitter. The number of fixed output amplifiers after every 60 km span is varied from 2 to 10 and corresponding accumulated ASE noise has been studied to manage timing jitter and BER in permissible range, i.e. 5 ps and 10⁻⁹, respectively. It is observed that when two fiber spans are taken then the compensating fiber length for the system is less than 20 km for each case of the chirp considered. For 10 fiber spans, the compensating fiber length increases in the range 60-90 km depending upon the value of chirp taken. Finally it is shown that the chirp value of external modulator should be set to either 0 or −1 for externally modulated RZ soliton pulse in 10 Gb/s optical communication system which makes the system more insensitive to the timing jitter and the selection of dispersion compensating fiber length.     

Multi-wavelength conversion at 10 Gb/s using cross-phase modulation in highly nonlinear fiber

In this paper we demonstrate a technique of signal wavelength conversion via cross-phase modulation (XPM)-induced nonlinear coupling among a 10 GHz return-to-zero (RZ) signal and a continuous wave (CW) carrier co-propagating in dispersion-shifted (DS) highly nonlinear fiber (HNLF). The wavelength conversion bandwidth up to ±20 nm was achieved experimentally and potential extension was verified by numerical simulations. The principle can easily be extended to 40 Gb/s and used as polarization insensitive all-optical wavelength converter.     

Simple and flexible generation of vestigial side band modified duobinary return-to-zero signals at 10, 20 and 40 Gb/s

We propose and demonstrate a simple and flexible approach to generate vestigial side band modified duobinary return-to-zero (VSB MD-RZ) signals at 10-40 Gb/s, using a dual-drive Mach-Zehnder modulator and a detuned optical band-pass filter. The performance of the proposed VSB MD-RZ signal is investigated by comparing with double side band MD-RZ (DSB MD-RZ) and conventional VSB MD-RZ. Bit error ratio (BER) measurement at 10 Gb/s shows an error free operation for the generated signal. Good performance is further observed after 100 km of single-mode-fiber transmission at 40 Gb/s.     

10 Gb/s WDM-PON based on FP-LDs injection locked by downlink optical carrier

We propose and demonstrate a 10 Gb/s wavelength division multiplexed passive optical network (WDM-PON) where subcarriers are employed to transmit the downstream data and optical carriers of the downlink subcarrier modulated (SCM) lights are reused to injection lock Fabry-Perot laser diodes (FP-LDs) for uplink transmission. Experiment results show that a very good BER performance can be achieved for both uplink and downlink at 10 Gb/s. The impact of optical carrier to subcarrier ratio and wavelength mismatching is also investigated.     

10 Gb/s TDM passive optical networks using four wavelengths multiplexed channels

We propose a new architecture for 10 Gb/s upstream traffic in TDM-PON using externally injection-locked Fabry-Perot laser diodes (FP-LDs) in each optical network unit (ONU). Four directly modulated 2.5 Gb/s FP-LDs were injection-locked by continuous wave (CW) carriers distributed from the optical line terminal (OLT). Hence, a total of 10 Gb/s upstream traffic can be achieved. Experimental results show negligible power penalty at a transmission of 25 km standard single mode fiber (SMF) without dispersion compensation. The performance of the injection-locked FP-LD is also studied.     

100 Gb/s RZ-OOK transmission through 212 km deployed SSMF using monolithically integrated ETDM receiver module

100 Gb/s on-off keying (OOK) transmission over 212 km installed standard single-mode fibers using an Indium Phosphide (InP)-based electrical clock-data-recovery (CDR) and demultiplexer module was demonstrated. 5.5 × 10^− 11 bit error rate (BER) performance was achieved and 1.1-dB optical signal-to-noise ratio (OSNR) penalty was required at 10^− 9 BER after transmission.     

Adding channels with PSBT format at 40 Gbit/s in an existing 10 Gbit/s optical network

Until recently, the wavelength-division-multiplexed (WDM) transmission system has reached record capacities and distances due to innovations such as FEC (Forward Error Correction), distributed Raman amplification, new transmission fiber and advanced optical format. Optical-communication systems exclusively employed conventional On-Off Keying signals in either Non-Return-To-Zero (NRZ) or Return-To-Zero (RZ) format. Recently a number of advanced modulation formats have attracted attention. Some of these formats carry information through On-Off-Keying but also modulate the optical phase in order to enhance the robustness of signal to chromatic dispersion, optical filtering and non-linearities. Through extensive sets of simulation results, we showed that it is possible to replace a channel with higher bit-rate on existing DPSK or OOK at 10Gbit/s transmission link. Duobinary formats are ideal candidates to do it and are known for their low spectral range and high tolerance to residual chromatic dispersion. These particularities make them very attractive for both high bit rates and high distance-transmissions. Today, Phase Shaped Binary Transmission (PSBT) is considered as being the promising format for the deployment of 40Gbit/s technology on existing links at 10Gbit/s WDM long haul transmissions.     

Ultra high-speed optical signal processing based on single SOA at 60 Gb/s

The paper shows the design of all-optical logic gates OR, AND, NOT, NOR, XNOR, XOR at ultra high speed by using SOA. The simulations of all logic gates are obtained by XGM and FWM in SOA at 40 Gb/s and 60 Gb/s. The OR, AND, NOR logic between two data sources are obtained using a pump signal, while another logic XNOR using two data. The NOT, XOR obtained using FWM and XGM combined. Thus realization of these logics at 40 Gb/s and 60 Gb/s will lead revolution growth in optical signal processing for high-speed operation.     

Optimizing the thulium doped fiber amplifier (TDFA) gain and noise figure for S-band 16 × 10 Gb/s WDM systems

This paper aims to evaluate a comprehensive numerical model based on solving rate equations of a thulium-doped silica-based fiber amplifier. The pump power and thulium-doped fiber (TDF) length for single-pass thulium-doped fiber amplifiers (TDFA) are theoretically optimized to achieve the optimum gain and noise figure (NF) at the center of S-band region. The 1064 nm pump is used to provide both ground-state and excited state absorptions for amplification in the S-band region. The theoretical result is in agreement with the published experimental result.     

Turbo-switched Mach-Zehnder interferometer performance as all-optical signal processing element at 160 Gb/s

Two variations of the active Mach-Zehnder interferometer (MZI) that incorporate the recently proposed turbo-switch effect are introduced to carry out three key functionalities in forthcoming high-speed optical telecommunication networks, namely, all-optical wavelength conversion, photonic XOR gating and optical time-division demultiplexing. Their performance is numerically investigated at 160 Gb/s using a sophisticated semiconductor optical amplifier (SOA) model. The more practical of the two proposed geometries shows error-free operation as XOR Boolean gate, low patterning as wavelength converter, and poor performance as demultiplexer. For comparison, results derived from well-accepted (or typical) schemes are also presented, and the role of the required extra SOAs as distinguishing elements of the new architectures is investigated.     

Si-based near infrared photodetectors operating at 10 Gbit/s

We report on fast p-i-n near infrared photodetectors in pure germanium on silicon. The diodes were fabricated by chemical vapor deposition at 600 °C followed by thermal annealing at 900 °C. We also verified that bypassing the thermal treatment did not have significant effects on the resulting crystal quality, allowing to considerably reducing the thermal budget hence simplify the integration with silicon. We demonstrate the operation of photodiodes with responsivities of 0.4 and 0.2 A/W at 1.3 and 1.55 μm, respectively, as well as open-eye diagrams at 10 Gbit/s.     

Utilization of four WDM channels with signal remodulation of OFDM-QAM for 10 Gb/s uplink passive optical networks

In this investigation, we experimentally investigate an extended reach (ER) time-division-multiplexed passive optical network (TDM-PON) using four wavelength-multiplexed channels to achieve 16 Gb/s downlink and 10 Gb/s uplink traffic. Each downlink signal uses the highly spectral efficient 4 Gb/s OFDM-QAM, and each uplink signal is generated by signal remodulating the downlink signal via a reflective semiconductor amplifier (RSOA) at 2.5 Gb/s non-return-to-zero (NRZ). In addition, the performance of the proposed ER TDM-PON has also been analyzed and discussed.