Cloud point extraction for cobalt preconcentration with on-line phase separation in a knotted reactor followed by ETAAS determination in drinking waters

A novel method for cobalt preconcentration by cloud point extraction with on-line phase separation in a PTFE knotted reactor and further determination by electrothermal atomic absorption spectrometry (ETAAS) is proposed. The cloud point system was formed in the presence of non-ionic micelles of polyethyleneglycolmono-p-nonylphenylether (PONPE 7.5) and it was retained on the inner walls of a knotted reactor (KR). The surfactant rich-phase was removed from the knotted reactor with 75 microL of methanol acidified with 0.8 mol L(-1) nitric acid, directly into the dosing hole of the L'Vov graphite tube. An enrichment factor of 15 was obtained with a preconcentration time of 60 s, with respect to the direct determination of cobalt by ETAAS in aqueous solutions. The value of the detection limit for the preconcentration of 5 mL of sample solution was 10 ng L(-1). The precision, expressed as the relative standard deviation (R.S.D.), for 10 replicate determinations at 0.5 microg L(-1) Co level was 4.5%. Verification of the accuracy was carried out by analysis of a standard reference material (NIST SRM 1640e "Trace elements in natural water"). The method was successfully applied to the determination of cobalt in drinking water samples.     

Cloud point extraction of mercury with PONPE 7.5 prior to its determination in biological samples by ETAAS

Cloud point extraction (CPE) has been used for the pre-concentration of mercury, after the formation of a complex with 2-(5-bromo-2-pyridylazo)-5-(diethylamino)-phenol (5-Br-PADAP), and later analysis by electrothermal atomic absorption spectrometry (ETAAS) using polyethyleneglycolmono-p-nonyphenylether (PONPE 7.5) as surfactant. The chemical variables affecting the separation step were optimized. Under the optimum conditions, i.e, pH 8.5, cloud point temperature 80 degrees C, 5-Br-PADAP=4x10(-5) mol L(-1), PONPE 7.5=0.2%, sample volume=1.0 mL, an enhancement factor of 22-fold was reached. The lower limit of detection (LOD) obtained under the optimal conditions was 0.01 microg L(-1). The precision for 10 replicate determinations at 2.0 microg L(-1) Hg was 4.0% relative standard deviation (R.S.D.). The calibration graph using the pre-concentration system for mercury was linear with a correlation coefficient of 0.9994 at levels near the detection limits up to at least 16 microg L(-1). The method was successfully applied to the determination of mercury in biological samples and in certified reference material (QC METAL LL3).     

On-line complexation/cloud point preconcentration for the sensitive determination of dysprosium in urine by flow injection inductively coupled plasma–optical emission spectrometry

An on-line dysprosium preconcentration and determination system based on the hyphenation of cloud point extraction (CPE) to flow injection analysis (FIA) associated with ICP-OES was studied. For the preconcentration of dysprosium, a Dy(III)-2-(5-bromo-2-pyridylazo)-5-diethylaminophenol complex was formed on-line at pH 9.22 in the presence of nonionic micelles of PONPE-7.5. The micellar system containing the complex was thermostated at 30 degrees C in order to promote phase separation, and the surfactant-rich phase was retained in a microcolumn packed with cotton at pH 9.2. The surfactant-rich phase was eluted with 4 mol L(-1) nitric acid at a flow rate of 1.5 mL min(-1), directly in the nebulizer of the plasma. An enhancement factor of 50 was obtained for the preconcentration of 50 mL of sample solution. The detection limit value for the preconcentration of 50 mL of aqueous solution of Dy was 0.03 microg L(-1). The precision for 10 replicate determinations at the 2.0 microg L(-1)Dy level was 2.2% relative standard deviation (RSD), calculated from the peak heights obtained. The calibration graph using the preconcentration system for dysprosium was linear with a correlation coefficient of 0.9994 at levels near the detection limits up to at least 100 microg L(-1). The method was successfully applied to the determination of dysprosium in urine.     

Ultratrace determination of cadmium by cold vapor atomic absorption spectrometry after preconcentration with a simplified cloud point extraction methodology

A simplified micelle-mediated extraction methodology for the preconcentration of ultratrace levels of cadmium as a prior step to its determination by cold vapor atomic absorption spectrometry (CV-AAS) has been developed. The methodology is based on the cloud point extraction (CPE) of cadmium at pH 8 by using the non-ionic surfactant polyethyleneglycolmono-p-nonylphenylether (PONPE 7.5) without adding any chelating agent. Cadmium cold vapor was generated from 2 ml of the extracted surfactant-rich phase by means of sodium tetrahydroborate (3%, w/v) as a reducing agent and hydrochloric acid (0.2 mol l⁻¹) as a carrier solution. Several important variables that affect the cloud point extraction and cold vapor cadmium generation efficiency were investigated and optimized. The preconcentration of only 50 ml of solution in the presence of 0.06% (v/v) PONPE 7.5 gives an enhancement factor of 62. The calibration graph using the preconcentration system was linear in the range of 4-100 ng l⁻¹ with a correlation coefficient of 0.9992. Detection limit (3 s) obtained in the optimal conditions was 0.56 ng l⁻¹. The relative standard deviation (R.S.D.) for six replicate determinations at 20 ng l⁻¹ Cd level was 3.2%. The proposed method was successfully applied to the ultratrace determination of cadmium in water samples.     

Monitoring the elimination of gadolinium-based pharmaceuticals. Cloud point preconcentration and spectrophotometric determination of Gd(III)-2-(3,5-dichloro-2-pyridylazo)-5-dimethylaminophenol in urine

An extraction methodology based on cloud point phase separation of non-ionic surfactants has been developed for the preconcentration of ppb amounts of gadolinium in urine as a prior step to its determination by an absorptiometric procedure. A method based on the formation of complexes with 2-(3,5-dichloro-2-pyridylazo)-5-dimethylaminophenol was used for the extraction of Gd(III) in the surfactant-rich phase of non-ionic surfactant polyethyleneglycolmono-p-nonylphenylether (PONPE 7.5). The variables affecting the combined preconcentration-absorptiometric method have been evaluated and optimised. The extraction efficiency, linearity, and the limit of detection (LOD) of the method were determined. The optimised procedure was applied to determine total and free Gd(III) contents in real urine samples of patients after the NMR imaging diagnostic examination with contrast agent.     

Indirect quantification of trace levels cyanide in environmental waters through flame atomic absorption spectrometry coupled with cloud point extraction

Cloud point extraction (CPE) has been used for the preconcentration and indirect quantification of cyanide after the formation of a ion-associate complex with 3-amino-7-diethylamino-8,9-benzo-2-phenoxazine chloride (Nile blue, NB⁺) in the presence of copper (II) ions, and later analysis by flame atomic absorption spectrometry (FAAS) using polyethyleneglycolmono-p-nonylphenylether (PONPE 7.5) as extracting surfactant. The chemical variables affecting the separation phase and the viscosity affecting the detection process were optimized. At pH 5.5, preconcentration of only 50 mL of sample in the presence of 0.04 % (w/v) PONPE 7.5 and 5.64 × 10^?5 mol L^?1 Nile blue permitted the detection of 3.75 μg L^?1 cyanide. The enhancement factor was 64.7 for cyanide. The proposed method was successfully applied to the determination of free cyanide in environmental water samples. The method was compared with the pyridine–barbituric acid method and the paired t test was used to determine whether the results obtained by the two methods differ significantly.     

The separation of platinum and palladium by selective extraction of H(2)Pt(SCN)(6) and H(2)Pd(SCN)(4) using a polyTHF-impregnated filter

Platinum and palladium are known to form complexes with the thiocyanate ion in solution. The isolation and separation of both platinum and palladium as thiocyanate complexes is demonstrated by passing them through an organic-impregnated filter (OIF) prepared with polyTHF. Simultaneous extraction is performed by converting both metals into the extractable form. Sequential extraction is achieved by exploiting the difference in the rates of formation for the extractable complexes of the two metals. The extraction of both metals is rapid with quantitative recoveries of platinum with flow rates as high as 600 ml min⁻¹ in small samples, while recoveries from larger volume samples were considerably lower. Once extracted, the metals can be removed from the OIF by conversion to a non-extractable form with a high pH eluting solution. The rapid separation, isolation and preconcentration of both platinum and palladium from aqueous samples is demonstrated.     

Rapid determination of lead in water samples by dispersive liquid-liquid microextraction coupled with electrothermal atomic absorption spectrometry

The need for highly reliable methods for the determination of trace and ultratrace elements has been recognized in analytical chemistry and environmental science. A simple and powerful microextraction technique was used for the detection of the lead ultratrace amounts in water samples using the dispersive liquid-liquid microextraction (DLLME), followed by the electrothermal atomic absorption spectrometry (ET AAS). In this microextraction technique, a mixture of 0.50 mL acetone (disperser solvent), containing 35 microL carbon tetrachloride (extraction solvent) and 5 microL diethyldithiophosphoric acid (chelating agent), was rapidly injected by syringe into the 5.00 mL water sample, spiked with lead. In this process, the lead ions reacted with the chelating agent and were extracted into the fine droplets of CCl(4). After centrifugation (2 min at 5000 rpm), the fine CCl4 droplets were sedimented at the bottom of the conical test tube (25+/-1 microL). Then, 20 microL from the sedimented phase, containing the enriched analyte, was determined by ET AAS. The next step was the optimization of various experimental conditions, affecting DLLME, such as the type and the volume of the extraction solvent, the type and the volume of the disperser solvent, the extraction time, the salt effect, pH and the chelating agent amount. Moreover, the effect of the interfering ions on the analytes recovery was also investigated. Under the optimum conditions, the enrichment factor of 150 was obtained from only a 5.00 mL water sample. The calibration graph was linear in the range of 0.05-1 microg L(-1) with the detection limit of 0.02 microg L(-1). The relative standard deviation (R.S.D.) for seven replicate measurements of 0.50 microg L(-1) of lead was 2.5%. The relative lead recoveries in mineral, tap, well and sea water samples at the spiking level of 0.20 and 0.40 microg L(-1) varied from 93.5 to 105.0. The characteristics of the proposed method were compared with the cloud point extraction (CPE), the liquid-liquid extraction, the solid phase extraction (SPE), the on-line solid phase extraction (SPE) and the co-precipitation, based on bibliographic data. The main DLLME advantages combined with ET AAS were simplicity of operation, rapidity, low cost, high-enrichment factor, good repeatability, low consumption of extraction solvent, requiring a low sample volume (5.00 mL).     

Online trace enrichment to determine pyrethroids in river water by HPLC with column switching and photochemical induced fluorescence detection

The potential of online trace enrichment on a highly apolar short column in LC was evaluated for the determination of pyrethroids in river water. Twelve millilitres of water samples, modified with 8 mL ACN (ACN/water 40:60, v/v), were passed through 50 x 4.6 mm ID first separation column packed with 5 microm Hypersil Elite C18. Pesticides were preconcentrated in this column while the matrix background was eluted to waste. Separation of pesticides was performed on a 3.5 microm symmetric C18 column (250 x 4.6 mm ID) with an ACN step gradient as mobile phase and fluorescence detection was used after postcolumn derivatization by using UV light. The use of photochemically induced fluorescence for detection improved sensitivity and selectivity. Quantification limits ranged from 0.05 to 0.1 microg/L and pesticide recoveries at two concentration levels (0.1 and 0.5 microg/L) were between 93.1 and 118.6%, with RSD between 2.5 and 7.5% (n = 3) in river water samples. No matrix effect was detected.     

Simplified cloud point extraction for the preconcentration of ultra-trace amounts of gold prior to determination by electrothermal atomic absorption spectrometry

A simple and sensitive cloud point extraction method has been developed for the preconcentration of ultra-trace amounts of gold as a prior step to its determination by electrothermal atomic absorption spectrometry. It is based on the extraction of gold in hydrochloric acid medium using the non-ionic surfactant polyethyleneglycolmono-p-nonylphenylether (PONPE 7.5) without adding a chelating agent. The preconcentration of a 50 mL sample solution was thus enhanced by a factor of 200. The resulting calibration graph was linear in the range of 10–200 ng L⁻¹ with a correlation coefficient of 0.9993. The limit of detection (3s) obtained under optimal conditions was 2.0 ng L⁻¹. The relative standard deviation for 10 replicate determinations at a 100 ng L⁻¹ Au level was 3.6%. The method was applied to the ultra-trace determination of gold in water and copper samples.     

Determination of some organophosphorus and azole group pesticides in water samples by dispersive liquid-liquid microextraction coupled with GC/MS

A dispersive liquid-liquid microextraction (DLLME) procedure coupled with GC/MS detection is described for preconcentration and determination of some organophosphorus and azole group pesticides from water samples. Experimental conditions affecting the DLLME procedure were optimized by means of an experimental design. A mixture of 60 microL chlorobenzene (extraction solvent) and 750 microL acetonitrile (disperser solvent), 3.5 min extraction time, and 7.5 mL aqueous sample volume were chosen for the best recovery by DLLME. The linear range was 1.6-32 microg/L. The LOD ranged from 48.8 to 68.7 ng/L. The RSD values for organophosphorus and azole group pesticides at spiking levels of 3, 6, and 9 microg/L in water samples were in the range of 1.1-12.8%. The applicability and accuracy of the developed method were determined by analysis of spiked water samples, and the recoveries of the analyzed pesticides from artesian, stream, and tap waters at spiking levels of 3, 6, and 9 microg/L were 89.3-105.6, 89.5-103.0, and 92.0-111.3%, respectively.     

Spectrophotometric determination of trace aluminium content in parenteral solutions by combined cloud point preconcentration-flow injection analysis

A cloud point preconcentration and flow injection (FI) analysis methodology for aluminium(III) determination has been developed. The analyte in the initial aqueous solution was complexed with Chrome Azurol S (CAS) in the presence of the cationic surfactant benzyldimethyltetradecylammonium chloride (BDTAC). The absorption spectroscopic characteristics of the ternary complex [Al(III)-CAS-BDTAC] were examined in detail. The preconcentration step was carried out by means of the non-ionic surfactant polyethylene glycol p-nonylphenyl ether (PONPE 7.5). The enriched analyte solution was injected into an FI system using an HPLC pump. The chemical variables affecting the analytical performance of the combined methodology were studied and optimised. The developed approach was successfully applied to the determination of trace amounts of aluminium in parenteral solutions without previous treatment. Under the optimum experimental conditions, 99.9% extraction was achieved for a preconcentration factor of 50. The limit of detection was 1.12 x 10(-7) mol(-1). The calibration plot was linear over at least two orders of magnitude of aluminium concentration. The developed coupled methodology, which thoroughly satisfies the typical requirements for pharmaceutical control processes, is appropriate for monitoring the aluminium concentration in parenteral nutrition.     

Optimization of dispersive liquid-liquid microextraction of copper (II) by atomic absorption spectrometry as its oxinate chelate: application to determination of copper in different water samples

In this study a dispersive liquid-liquid microextraction (DLLME) method based on the dispersion of an extraction solvent into aqueous phase in the presence of a dispersive solvent was investigated for the preconcentration of Cu(2+) ions. 8-Hydroxy quinoline was used as a chelating agent prior to extraction. Flame atomic absorption spectrometry using an acetylene-air flame was used for quantitation of the analyte after preconcentration. The effect of various experimental parameters on the extraction was investigated using two optimization methods, one variable at a time and central composite design. The experimental design was performed at five levels of the operating parameters. Nearly the same results for optimization were obtained using both methods: sample size 5 mL; volume of dispersive solvent 1.5 mL; dispersive solvent methanol; extracting solvent chloroform; extracting solvent volume 250 microL; 8-hydroxy quinoline concentration and salt amount do not affect significantly the extraction. Under the optimum conditions the calibration graph was linear over the range 50-2000 muicro L(-1). The relative standard deviation was 5.1% for six repeated determinations at a concentration of 500 microg L(-1). The limit of detection (S/N=3) was 3 microg L(-1).     

Development of Cloud Point Extraction for Simultaneous Extraction and Determination of Platinum and Palladium Using Inductively Coupled Plasma Optical Emission Spectrometry in Platinum-Palladium Spent Catalysts

A new on-line cloud point extraction system coupled to inductively coupled plasma optical emission spectrometry was designed for simultaneous extraction, preconcentration and determination of trace amounts of platinum and palladium in platinum-palladium spent catalysts. This was based on the complexation of the metal ions with 1,8-diamino-4,5-bis(hydroxyamino)anthraquinone reagent in the presence of non-ionic surfactant of Triton X-114. After phase separation, the surfactant-rich phase was diluted with concentrated HNO₃ (70%, w/w); the analytes concentrations were determined by inductively coupled plasma-optical emission spectrometry. Several factors influencing the instrumental conditions and extraction were evaluated and optimized. Under the optimum conditions, the enhancement factors of the proposed method were 35.4 and 29 for platinum and palladium, respectively. The detection limits were 0.3 and 0.45 µ g L^?1. Finally, the developed method was successfully applied to the extraction and determination of platinum and palladium in platinum-palladium spent catalysts samples and satisfactory results were obtained.     

Cloud point extraction combined with micellar electrokinetic capillary chromatography determination of benzophenones in cosmetic matrix

A method has been developed for the separation and determination of three hydrophobic benzophenones: 2,4-dihydroxybenzophenone (BP-1), 2,2'4,4'-tetrahydroxybenzophenone (BP-2), and 2-hydroxy-4-methoxybenzophenone (BP-3) in sunscreen by micellar electrokinetic capillary chromatography (MEKC) combined with cloud point extraction (CPE). The analytes were extracted at pH 5.0 by micelles of the nonionic surfactant polyoxyethylene-7.5-octylphenyl ether (Triton X-114). A 150 microL aliquot from the extracted surfactant-rich phase was diluted up to 500 microL with ethanol to reduce its viscosity before separation by MEKC. A background electrolyte of 25 mmol/L sodium tetraborate containing 30 mmol/L sodium dodecyl sulfate at pH 9.25 was used as the separation medium to avoid the adsorption of hydrophobic substances and Triton X-114 onto the inner surface of the separation capillary, ensuring the separation efficiency and reproducibility. Detection is performed at 290 nm. Under the optimized conditions, an enrichment factor of 20 was obtained and the determination limits of BP-1, BP-2, and BP-3 were found to be 3.90 x 10(-) (7), 3.83 x 10(-7), and 6.42 x 10(-8) mol/L, respectively. In comparison with the earlier reported methods, the LODs of this method are superior to the other methods. The presented procedure was successfully applied to the determination of BP-1, BP-2, and BP-3 in sunscreen with satisfactory results.     

HPLC method for the simultaneous determination of atenolol and chlorthalidone in human breast milk

A high-performance liquid chromatographic method was optimized and validated for the determination of atenolol and chlorthalidone (CT) in human breast milk. The milk samples were extracted and purified using ACN and phosphoric acid for precipitation of proteins followed by removal of ACN and milk fats by extraction with methylene chloride. The samples were applied, after an extraction procedure, to a cyanide column using a mobile phase consisting of ACN/water (35:65 v/v) and buffered at pH 4.0 with flow rate of 1.0 mL/min. Quantitation was achieved with UV detection at 225 nm using guaifenesin as the internal standard. The effectiveness of protein precipitation and clean up procedure were investigated. The method was validated over the range of 0.3-20 microg/mL for atenolol and 0.25-5 microg/mL for CT.     

Determination of trace amounts of Pd(II) ions in water and road dust samples by flame atomic absorption spectrometry after preconcentration on modified organo nanoclay

This paper describes the application of organo nanoclay, an easily prepared and stable solid sorbent, to the preconcentration of trace amounts of palladium ions in aqueous solution. The organo nanoclay was prepared by adding tetradecyldimethylbenzylamonium chloride onto montmorillonite, which was then modified with 1-(2-pyridylazo)-2-naphthol. The modified nanoclay was used as a solid sorbent for separation and preconcentration of trace amounts of Pd(II) ions, and a simple, sensitive, and economical method was developed for determination of trace amounts of palladium by flame atomic absorption spectrometry. The sorption of Pd(II) ions was quantitative in the pH range of 1.5-5.0, whereas quantitative desorption occurred with 5.0 mL of a mixture containing 1.0 M thiourea and 1.0 M HCl. The RSD of the method was +/- 2.1% (n = 10; concn = 0.5 microg/mL), and the LOD (3sigma(bl); sigma = SD and bl = blank) was 0.1 ng/mL. The calibration curve was linear for concentrations of 0.5-8.0 microg/mL in the initial solution, and the preconcentration factor was 140. The maximum capacity of the sorbent was 2.4 mg Pd(II)/g modified organo nanoclay. The influences of the experimental parameters, including sample pH, eluant volume, eluant type, sample volume, and interfering ions, on the recoveries of the palladium ion were investigated. The proposed method was applied to the preconcentration and determination of palladium in different samples.     

Determination of ofloxacin and gatifloxacin by mixed micelle-mediated cloud point extraction-fluorimetry combined methodology

A cloud point extraction process using mixed micelle of the anionic surfactant sodium dodecyl sulfate (SDS) and the non-ionic surfactant polyoxyethylene(7.5)nonylphenylether (PONPE 7.5) to extract two fluoroquinolone antimicrobial agents, ofloxacin and gatifloxacin, from aqueous media was investigated. The method is based on the mixed micelle-mediated extraction of fluoroquinolones in the presence of NaCl as an inducing agent in phase separation, followed by spectrofluorimetric determination. The effect of different variables such as pH, PONPE7.5 concentration, SDS concentration, NaCl concentration, cloud point temperature, and time was investigated, and optimum conditions were established. At optimum conditions, the rectilinear calibration graphs were obtained in the concentration range of 0.1–150 and 0.1–250 ng mL^?1 for ofloxacin and gatifloxacin, and the limits of detection were 0.04 and 0.06 ng mL^?1, respectively. The proposed procedure was applied successfully for the detection of the investigated drugs in their pharmaceutical dosage forms, in spiked plasma, spiked urine, and urine samples, with good precision and accuracy.     

Highly selective cloud point extraction and preconcentration of trace amounts of silver in water samples using synthesized Schiff’s base followed by flame atomic absorption spectrometric determination

A simple and useful method employing cloud point extraction is proposed for the preconcentration and separation of silver in water samples. The silver cation reacts with bis(2-mercaptoanil) acetylacetone (BMAA) at pH 6. The resulting compound is subsequently entrapped in the Triton X-114 micelles. After optimization of the complexation and extraction conditions, a preconcentration factor of 50 was obtained (volume of initial sample was 10 mL). As an analytical example, trace amounts of Ag were determined, after preconcentration, in a complex aqueous matrix such as seawater using flame atomic absorption spectrometry. The calibration curve was linear in the range 2–200 ng/mL and the limit of detection was 0.43 ng/mL. The relative standard deviation was lower than 2.4%. The text was submitted by the authors in English.     

In-capillary preconcentration of pirimicarb and carbendazim with a monolithic polymeric sorbent prior to separation by CZE

CZE was assayed for the separation of carbamate pesticides susceptible to protonation (Pirimicarb, Carbendazim). Different electrophoretic media with high organic contents were explored, adequate separation and resolution being achieved when a BGE based on ACN with acetic acid in the presence of SDS as an ionic additive was used. With a view to increasing the sensitivity of the method, an in-capillary SPE step prior to the electrophoretic separation was developed. We employed a monolithic polymer formed in situ within the capillary as a medium for analyte retention. The synthesized monolithic bed exhibited high porosity and allowed samples to be loaded at flow rates of about 65 microL/min by applying a pressure of 12 bar. A 5-cm length of monolithic sorbent was used to preconcentrate the target analytes from aqueous samples. The analytes retained were eluted from the polymeric phase directly in the separation capillary with the same electrophoretic medium used for their further separation by CZE. For a 15-min preconcentration time, the in-line SPE-CZE approach proposed here permitted the determination of these pesticides in drinking water at a concentration level of 0.1 microg/L, as demanded by current EU legislation.