Thermodynamic study of glasses in Ag-As-Se system using EMF method with Ag<Subscript>4</Subscript>RbI<Subscript>5</Subscript> solid electrolyte

The EMF method with Ag₄RbI₅ solid electrolyte was used to study silver solubility in Ag-As-Se glasses on the basis of the cross-sections of (I) Ag-As_0.25Se_0.75, (II) Ag-As_0.33Se_0.67, (III) Ag-As_0.4Se_0.6, and (IV) Ag-As_0.5Se_0.5. It is found that silver solubility reaches 30 and 40 at % in sections (I), (IV) and (II), (III), accordingly. The data of EMF measurements were used as a basis for calculation of partial polar functions of Ag in glasses. The Gibbs-Duhem equations were integrated to calculate thermodynamic functions of silver dissolution in vitreous As _x Se_{1 − x} (x = 0.25; 0.33; 0.4; 0.5), from which the corresponding data for the latter were used to obtain the standard integral thermodynamic functions of the mixing of glasses. The obtained results were compared with the thermodynamic data for crystalline silver selenoarsenites.     

TeO2-WO3 Glasses: Infrared, XPS and XANES Structural Characterizations

Transparent (1−x)TeO₂-xWO₃ glasses with 0≤x≤0.325 mol were synthesized by the fast quenching technique. Several complementary techniques as infrared, X-ray photoelectron and X-ray absorption spectroscopies were used to approach the structure of these tungsten oxide-tellurite glasses. Special attention was paid to the oxidation state and the coordination state of tungsten atoms. The structural results show that (1−x)TeO₂-xWO₃ glasses present characteristic tellurium environments which vary with their chemical composition while tungsten ions always adopt an octahedral configuration.     

Thermal coefficient of linear expansion of non-crystalline chalcogenides in the As-S-Se-Te-I system

The object of the paper is an investigation of the glasses of the (As₂S₃)_x(AsSe_0.5Te_0.5I)_100-x. type for 65≤;x≤;95, using methods of thermomechanical analysis. Values of the thermal coefficients of linear expansion in solid and visco-plastic phase were determined. it was shown that introducing arsenic-sulfide in glass-matrix AsChI, i.e. (AsSe_0.5Te_0.5I), leads to an increasing stability of these glasses. The characteristic temperatures of softening Tg and the temperature of the beginning of deformation t_w increase by increasing content of As₂S₃. The analytical forms of dependence of four significant physical values α_g, α_l, Tg, Tw, as a function of As₂S₃ content in the structure of glasses were fitted. This revised version was published online in July 2006 with corrections to the Cover Date.     

Thermal properties and stability of lithium titanophosphate glasses

DTA was used to study thermal properties and thermal stability of (50-x)Li₂O-xTiO₂-50P₂O₅ (x=0–10 mol%) and 45Li₂Ot-yTiO₂-(55-y)P₂O₅ (y=5–20 mol%) glasses. The addition of TiO₂ to lithium phosphate glasses results in a non-linear increase of glass transition temperature. All prepared glasses crystallize under heating within the temperature range of 400–540°C. The lowest tendency towards crystallization have the glasses with x=7.5 and y=10 mol% TiO₂. X-ray diffraction analysis showed that major compounds formed by annealing of the glasses were LiPO₃, Li₄ P₂O₇, TiP₂O₇ and NASICON-type LiTi₂(PO₄)₃. DTA results also indicated that the maximum of nucleation rate for 45Li₂O-5TiO₂-50P₂O₅ glass is close to the glass transition temperature.     

Evaluation of specific heat and related thermodynamic properties of Ge1?xSnxSe2.5 (0?≤?x?≤?0.5) glasses

This paper presents the result of thermodynamic studies on Ge_1−x Sn _x Se_2.5 (0 ≤ x ≤ 0.5) glasses using differential scanning calorimetry. The obtained experimental results on phase transformations have been employed to obtain thermodynamic parameters like entropy difference between metastable states in the glassy region, difference of Gibbs free energy, specific heat, entropy between the glassy and the crystalline phase and the enthalpy released during phase transformation (glassy to crystalline). The results yield that, Ge_0.7Sn_0.3Se_2.5 sample is least stable among all the samples. The stability increases on addition of Sn beyond 0.3 at. mass% upto 0.5 at. mass%.     

Investigations on the Thermal and Elastic Properties of ZnO-Incorporated Phosphate Glasses and Glass Ceramics

Abstract

Glasses of the 45P₂O₅-(40-x)CaO-15Na₂O-xZnO system with increasing zinc oxide (ZnO) concentrations within the ranges of 3 ≤ x ≤ 12 mol% were obtained by employing the melt-quench technique. ZnO inclusions in the phosphate glass network lead to increases in its density and, conversely, a decrease in its molar volume. On the basis of the obtained thermal analysis data, the glasses underwent thermal treatment, which helped to derive their glass ceramic equivalents. The evaluations of structural and elastic properties of glasses before and after thermal treatments were made using X-ray diffraction (XRD) studies and ultrasonic nondestructive testing. The differential thermal analysis data show the reduction in the crystallization tendency and increase in thermal properties, such as crystallization temperature (T _P), thermal stability

(T _c – T _g) (where T_c is crystallization onset temperature and T _g is glass transition temperature), thermal stability parameter (S), and degree of glassification (D _g) of phosphate glasses against the progressive additions of ZnO. The XRD of glass ceramics confirmed the dominance of metaphosphate, pyrophosphate, and ZnO-related crystalline features. The measured elastic moduli, such as longitudinal (L), shear (G), Young's (Y), and bulk (K), and Vicker's microhardness values increased in both glass and glass ceramics with an increase in ZnO incorporation.     

Thermal analysis study of Bi<Subscript>2</Subscript>Sr<Subscript>2</Subscript>Ca<Subscript>2</Subscript>Cu<Subscript>3-x</Subscript>Er<Subscript>x</Subscript>O<Subscript>10+δ</Subscript> glass-ceramic system

Summary We have fabricated glasses in the Bi-2223 HT_c superconductor system with Bi₂Sr₂Ca₂Cu_3-xEr_xO_{10+ δ} nominal composition, where x=0.5 and 1.0, by the glass-ceramic technique. Using an analysis developed for non-isothermal crystallization studies, information on some aspects of crystallization temperature and thermal properties has been obtained. The crystallization studies were made using DTA with several uniform rates. The calculations of crystallization activation energies, E_a, and the Avrami parameters, n, were made based on the non-isothermal kinetic theory of Kissinger and the Ozawa’s equations. The DTA data of the samples showed that the first crystallization temperature, T_x1, increases and the second crystallization temperature, T_x2, decreases by increasing the Er concentration. This suggests that the Er substitution had significant effect on the glassification of the BSCCO material due to change on the surface nucleation and increased ionic activities at high temperature region. The activation energy for crystallization, E_a, of the samples was also showed an increase at high Er concentration case. However, the Avrami parameter, n, decreased from 2.5 to 1.7 for x=0.5 and 1.0 samples, respectively. This suggests that the growth mechanism is diffusion-controlled and three-dimensional parabolic growth takes place near the first crystallization temperature. The oxidization rates and the activation barrier for oxygen out-diffusion process, E, was calculated using the TG data. It was found that the total mass gain in the x=0.5 sample is comparably smaller than that of the x=1.0 sample. This shows that the oxygen absorption of the x=1.0 sample is faster than the x=0.5 sample, leading to increase in the oxidization rate in the x=1.0 material.     

Spectroscopic characterization of lithium doped borate glasses

B₂O₃-xLi₂O₃ (x=0, 0.1, 0.5) glasses have been prepared by the Sol-Gel method. The evolution of the composition and the structure of the materials upon thermal treatments are analyzed. Raman spectroscopy measurements reveal that the structure transforms from crystalline to amorphous. After a thermal treatment at 400°C, the materials exhibit a strong luminescence band which disappears upon further heating. In the case of no dopant (x=0) heating at 1150°C results in a Raman spectrum which is almost identical to the one corresponding to bulk B₂O₃ glass obtained by melting and quenching.     

Studies on Rare Earth Polyphosphate Glasses of the Composition [NaxM(1 − x)/2aGd(1 − x)/2aPO3]n

A fusion technique was used for the preparation of derivatives of the composition [Na _x M_{(1? x)/2a} Gd_{(1? x)/2a} PO₃] _n (where M = bivalent metal like Cu(II), Ca(II), Zn(II), Ni(II), and Mg (II); x = 1/2, 3/4, & 2/3; and a = valency of metal). Composition of these polyphosphate glasses was confirmed by their analyses for metals and phosphorus. The polymeric nature of all polyphosphate glasses was confirmed by the determination of a number average molecular weight (M _n ). The characteristic frequencies in the IR spectra are supportive of the presence of polyphosphate indicative of the polymeric nature of these derivatives. From X-ray diffraction, the amorphous nature of complex polyphosphates has been determined.     

Structural relaxation of PbO–WO3–P2O5 glasses

The structural relaxation of three compositional series of PbO–WO₃–P₂O₅ glasses with composition (0.5 ? x/2)PbO·xWO₃·(0.5 ? x/2)P₂O₅, x = 0, 0.1, 0.2, 0.3, 0.4, and 0.5; 0.5PbO·xWO₃·(0.5 ? x)P₂O₅, x = 0, 0.1, 0.2, and 0.3; and (0.5 ? x)PbO·xWO₃·0.5P₂O₅, x = 0, 0.1, 0.2, 0.3, 0.4, and 0.5 was studied by thermomechanical analysis. The structural relaxation was studied in the transformation region using the Tool–Narayanaswamy–Moynihan’s and Tool–Narayanaswamy–Mazurin’s models. The relaxation function of Kohlrausch Williams and Watts was used. The parameters of both models were calculated by nonlinear regression analysis of thermodilatometric curves measured by thermomechanical analyzer under the constant load. Both models very well describe the experimental data. It was found that the modulus is increasing with increasing amount of WO₃ in all glasses. On the contrary, the width of the spectrum of relaxation times is decreasing with increasing amount of WO₃ in all studied glasses. Both models possess the values of metastable melt thermal expansion coefficient equal to their experimental value.     

Application of heating microscopy to the study of thermal behaviour of ZnO–P2O5–WO3 glasses

The effect of WO₃ on thermal behaviour and thermal stability of ZnO–P₂O₅–WO₃ glasses prepared in compositional series (100 ? x)[0.5ZnO–0.5P₂O₅] ? xWO₃ (x = 0–60) was investigated by heating microscopy and the results were correlated with the results determined by conventional thermodilatometry and differential thermal analysis. Thermoanalytical studies showed that the glass transformation temperature and dilatation softening temperature increase with increasing WO₃ content while thermal expansion coefficient decreases. The highest stability towards crystallization possess glasses containing 20–30 mol% WO₃. Major compounds formed by the crystallization of the glasses were Zn(PO₃)₂, WO₃ and W₁₈P₂O₅₉. The values of sphere temperature, hemisphere temperature and flow temperature obtained using heating microscopy were strongly influenced by the degree of crystallization process at the sintering.     

Thermal studies of ZnO–B<Subscript>2</Subscript>O<Subscript>3</Subscript>–P<Subscript>2</Subscript>O<Subscript>5</Subscript>–TeO<Subscript>2</Subscript> glasses

The effect of TeO₂ additions on the thermal behaviour of zinc borophosphate glasses were studied in the compositional series (100 − x)[0.5ZnO–0.1B₂O₃–0.4P₂O₅]–xTeO₂ by differential scanning calorimetry, thermodilatometry and heating microscopy thermal analysis. The addition of TeO₂ to the starting borophosphate glass resulted in a linear increase of glass transition temperature and dilatometric softening temperature, whereas the thermal expansion coefficient decreased. Most of glasses crystallize under heating within the temperature range of 440–640 °C. The crystallization temperature steeply decreases with increasing TeO₂ content. The lowest tendency towards crystallization was observed for the glasses containing 50 and 60 mol% TeO₂. X-ray diffraction analysis showed that major compounds formed by annealing of the glasses were Zn₂P₂O₇, BPO₄ and α-TeO₂. Annealing of the powdered 50ZnO–10B₂O₃–40P₂O₅ glass leads at first to the formation of an unknown crystalline phase, which is gradually transformed to Zn₂P₂O₇ and BPO₄ during subsequent heating.     

LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> and LiCoO<Subscript>2</Subscript> composite cathode materials obtained by mechanical activation

New composite cathode materials xLiMn₂O₄/(1 ? x) LiCoO₂(x = 0.7, 0.6, 0.5 и 0.4) were obtained by mechanical activation. According to scanning electron microscopy data, the process was accompanied by pronounced dispersion and fine mixing of the initial components. In the course of the preparation and electrochemical cycling of the composites, LiMn₂O₄ and LiCoO₂ partially reacted, leading to the replacement of manganese with cobalt in the structure of spinel, which was detected by powder X-ray diffraction (XRD), IR and X-ray photoelectron spectroscopy (XPS), and cyclic chronopotentiometry. The specific discharge capacity of composites was ～100 mAh/g.     

New organosols of nickel sulfides,palladium sulfides,manganese sulfide,and mixed metal sulfides and their use in preparation of semiconducting polymer-metal sulfide composites

Organosols of NiS, PdS, and MnS in N,N-dimethylformamide were prepared by reaction of the metal acetate with H₂S. Organosols of mixed-metal sulfides (Zn _x Cd_1–x S, Hg _x Cd_1–x S, Hg _x Cu_1–x S, Cd _x Mn_1–x S, Hg _x Mn_1–x S, Hg _x Cd_1–x S, and Mn _x Zn_1–x S) were similarly obtained by reaction of mixtures of the metal salts with H₂S. The organosol of Zn_0.5Cd_0.5S contained particle with two particle size distributions centered at 6.5 nm and 29 nm, as revealed by Ar laser-scattering analysis. The metal sulfides are recovered by addition of Et₂O to the organosols. Zn _x Cd_1–x S thus obtained shows magnetic susceptibility in the range 0.5×10^–6–2.3×10^–6 emug^–1 depending on thex value. Addition of polymers to the organosols affords semiconducting films of metal sulfide-polymer composites.     

Zn0.4Ni0.6Cr0.5LaxFe1.5－xO4铁氧体纳米粉晶的制备及磁性

用柠檬酸盐前驱物-溶胶凝胶法制备了Zn_0.4Ni_0.6Cr_0.5La_xFe_1.5－xO₄ (x＝0～0.10)纳米粉晶. 用DSC-TG分析了前驱物转变为粉晶的热分解过程, 通过粉末X射线衍射仪(XRD)、透射电子显微镜(TEM)和振动样品磁强计(VSM)等表征了产物的结构、形貌和磁性能. 结果表明, 不同温度和不同的La掺杂量对样品的晶粒尺寸、晶胞参数和形貌均产生了明显的影响, 且通过改变La含量能起到调控样品磁性能的作用.     

Preparation and microstructure study of borosilicate coatings produced by sol-gel

Borosilicate coatings in the systems (100–x)SiO₂–xB₂O₃ (x=20, 30) and 75SiO₂-20B₂O₃-5Na₂O have been obtained using the dip-coating procedure. Stable solutions were prepared from TEOS and trimethylborate, H₂O/TEOS ratios being changed from 2 to 6. Sodium acetate in aqueous solution was used as Na₂O precursor. Coatings were prepared in an airtight glove-chamber with humidity and temperature control. Good and transparent films were obtained only for RH<20%. Microstructure evolution and phase separation phenomena were investigated by TEM studying their dependence on the water content of the solution, temperature and time of the heat treatment and thickness of the coatings. A comparison with similar melted glasses and bulk glasses prepared by sol-gel has been also established.     

Carbon monofluorides derived from sponge and shot cokes

Carbon fluoride compounds, CF _x , are used as cathode materials in commercially important primary Li/CF _x electrochemical power sources. New CF _x compounds were prepared, apparently for the first time, from sponge and shot cokes by direct fluorination. The carbon starting materials and CF _x products were characterized by X-ray diffraction, X-ray photoelectron spectroscopy, and elemental analysis for total fluorine. The discharge capacity of shot coke CF _x was unexpectedly low and is probably related to the heterogeneous nature of that form of coke. CF _x prepared from sponge coke that had been heated to 1930 °C exhibited the highest capacity, exceeding the capacity of a commercially available, battery grade CF _x . The discharge results show that CF _x from heated sponge coke has favorable electrochemical properties that render it attractive for lithium electrochemical power sources. Electronic Publication     

Synthesis and complex investigation of potassium ammonium hexafluorozirconates: I. Synthesis and X-ray diffraction study of K2-x (NH4)xZrF6 (0 < x < 2) crystals

The synthesis and X-ray diffraction study of compounds K_2-x (NH₄)xZrF₆ (0 < x < 2) were carried out. In all crystals of mixed composition, potassium cations are isomorphously replaced by ammonium cations. The compounds with x < 0.5 are isostructural to K₂ZrF₆ and those with x > 1.5, to (NH₄)₂ZrF₆. At 0.5 < x < 1.5, the structures are built of linear polymeric chains formed by edge-sharing Zr dodecahedra. The distribution of potassium and ammonium cations over the cationic positions was considered.     

Influence of the Mg-content on the cation distribution in cubic MgxFe3−xO4 nanoparticles

The influence of the Mg-content on the structural and magnetic properties of cubic Mg_xFe_3−xO₄ nanoparticles prepared by combustion reaction was investigated using X-ray diffraction, transmission electron microscopy (TEM), Mössbauer spectroscopy, and Raman spectroscopy. Lattice parameter, nanoparticle size, and cation (Mg²⁺, Fe³⁺) distribution were quantified as a function of the Mg-content in the range 0.5≤x≤1.5. We found a mixed-like spinel structure at the smaller x-value end whereas the inverse-like spinel structure dominates samples with larger x-values. Moreover, in the x-value range investigated (0.5≤x≤1.5) we found no change in the quadrupole splitting and isomer shift values, though the hyperfine field decreases as the x-value increases. The splitting of the A_1g Raman mode was used to both quantify the Mg²⁺/Fe³⁺ contents in the tetrahedral site and obtain the cation distribution in the Mg_xFe_3−xO₄ structure. The cation distribution obtained from the Raman data is in very good agreement with the cation distribution obtained from the Mössbauer data.     

The structure Tl3SbS3, Tl3SbSe3, Tl3SbS3−xSex, and Tl3SbyAs1−ySe3

The space group symmetry and crystal structure of Tl₃SbS_3−xSe_x compounds in the composition range 0 < x < 3 have been determined by a combination of powder X-ray diffraction, electron diffraction, and high-resolution electron microscopy. The incongruently melting compound Tl₃SbSe₃ has been shown to crystallize in cubic space group P2₁3 with a = 9.435Å in a structure related to that of Langbeinite. The convergent beam electron diffraction pattern of Tl₃SbS₃ is in accord with the space group R3m determined by X-ray diffraction. The cubic Langbeinite-type structure is found for Tl₃SbS_3−xSe_x for 0.5 < x < 3 and for Tl₃Sb_yAs_1−ySe₃ for 0.077 < y < 1.0. A five-component compound Tl₃Sb_0.5As_0.5Se_1.5S_1.5 was also found to be cubic.