掺杂助剂Ce和Zr的Ni/Al2O3催化剂的X光电子能谱分析

以Na2CO3为沉淀剂,在pH 9.0的沉淀条件下,采用并流沉淀法制备了Ni/Al2O3、Ni/CeO2-Al2O3、Ni/ZrO2-Al2O3和Ni/ZrO2-CeO2-Al2O34种催化剂,催化剂中Ni负载量(质量分数)为10%。采用XPS表征手段及常压固定床反应器对催化剂进行活性评价,考察了助剂Ce和Zr及二者的协同作用对Ni基催化剂表面物种结合能的影响以及对甲烷自热重整制氢反应性能的影响。结果表明,助剂Ce和Zr的添加及二者的协同作用对Ni基催化剂表面各物种的结合能均有一定的影响,结合评价结果可知,Ce和Zr二者的协同作用对Ni基催化剂的催化性能提高最大。     

CeO2掺杂RuO2/γ-Al2O3催化剂结构与湿式氧化降解苯酚的活性研究

采用浸渍法制备了RuO2/γ-Al2O3和RuO2-CeO2/γ-Al2O3催化剂,利用XRD,XPS和ESR分析了催化剂的结构,并研究了湿式氧化降解苯酚的活性.结果表明,两种催化剂表面RuO2均有良好的分散性,并且催化剂表面存在氧空位和化学吸附氧,CeO2的掺杂使催化剂表面氧空位和化学吸附氧数量增加.两种催化剂对湿式氧化降解苯酚具有良好的催化活性,当苯酚质量浓度为4200mg/L,在150℃和3MPa下,RuO2/γ-Al2O3催化剂湿式氧化降解苯酚反应150min后,苯酚全部被去除,RuO2-CeO2/γ-Al2O3催化剂反应60min后,苯酚的去除率为96%.     

Al含量对Pt-S2O82-/ZrO2-Al2O3型固体超强酸催化剂异构化性能的影响

通过向S₂O₈^2-/ZrO₂催化剂中同时引入适量的Pt和Al₂O₃, 制备出了具有较高催化性能和高稳定性的Pt-S₂O₈^2-/ZrO₂-Al₂O₃型固体超强酸催化剂. 以正戊烷异构化反应为探针, 考察了Al含量对催化剂的异构化性能的影响, 并采用XRD, BET, FTIR, TPR, TG-DTA, NH₃-TPD和ICP手段对催化剂进行了表征. 结果表明, Al能够延迟ZrO₂的晶化温度, 抑制硫的分解; Al能够增加催化剂的比表面积, 增强硫氧键的结合, 提高催化剂的还原性能, 增加催化剂的酸强度和酸总量. 当Al₂O₃质量分数为2.5%时, Pt-S₂O₈^2-/ZrO₂-Al₂O₃固体超强酸催化剂的催化活性最高, 正戊烷异构化收率可达60.02%, 选择性在98.2％以上.     

Pt含量及活化温度对固体超强酸催化剂异构化性能的影响

本文制备了固体超强酸Pt- S2O82-/ZrO2-Al2O3催化剂,采用XRD、TPR、TG-DTA 、FT-IR等表征手段对催化剂进行了表征,并在高压微反－色谱联合装置上,考察了Pt质量分数和活化温度对催化剂正戊烷异构化性能的影响. 结果表明,Pt能使催化剂的还原温度降低;增强载体表面氢气的溢流效应,提高酸强度;Pt质量分数0.10%、活化温度300℃的催化剂异构化活性最高,在反应温度220℃、压力2.0MPa、氢烃摩尔比4:1、质量空速1.0h-1时,异戊烷产率达62.3%. 在100h内异戊烷收率可稳定在55%左右,选择性在98.0％以上.     

Ni／ZrO2-Al2O3制备表征及催化性能的研究

本文采用浸渍沉淀法制备了不同配比的ZrO2-Al2O3复合载体。并通过浸渍法制备Ni/ZrO2-Al2O3催化剂,以苯加氢制环己烷反应为探针,考察了ZrO2与Al2O3的配比对Ni催化剂催化加氢性能的影响;采用X射线衍射(XRD)、程序升温还原(TPR)、程序升温脱附(TPD)等技术考察复合载体对Ni催化剂的体相结构、还原性能以及表面吸附性能的影响。研究结果表明,ZrO2质量分数为20%的复合载体所负载的Ni催化剂有很好的加氢活性,优于单组分载体负载的Ni催化剂;采用浸渍沉淀法制备的ZrO2-Al2O3复合载体中ZrO2以非晶态形式存在,这是由于Al2O3的存在影响了ZrO2的内部结构;该载体负载的Ni催化剂较其他催化剂更容易被还原,吸附中心数量增加。     

Methane reforming With CO2 to syngas over CeO2-promoted Ni/Al2O3-ZrO2 catalysts Prepared Via a direct sol-gel process

CeO2-promoted Ni/Al2O3-ZrO2 (Ni/Al2O3-ZrO2-CeO2) catalysts were prepared by a direct sol-gel process with citric acid as gelling agent. The catalysts used for the methane reforming with CO2 was studied by infrared spectroscopy (IR), thermal gravimetric analysis (TGA), microscopic analysis, X-ray diffraction (XRD) and temperature-programmed reduction (TPR). The catalytic performance for CO2 reforming of methane to synthesis gas was investigated in a continuous-flow micro-reactor under atmospheric pressure. TGA, IR, XRD and microscopic analysis show that the catalysts prepared by the direct sol-gel process consist of Ni particles with a nanostructure of around 5 nm and an amorphous-phase composite oxide support. There exists a chemical interaction between metallic Ni particles and supports, which makes metallic Ni well dispersed, highly active and stable. The addition of CeO2 effectively improves the dispersion and the stability of Ni particles of the prepared catalysts, and enhances the adsorption of CO2 on the surface of catalysts. The catalytic tests for methane reforming with CO2 to synthesis gas show that the Ni/Al2O3-ZrO2-CeO2 catalysts show excellent activity and stability compared with the Ni/Al2O3 catalyst. The excellent catalytic activity and stability of the Ni/Al2O3-ZrO2-CeO2 are attributed to the highly, uniformly and stably dispersed small metallic Ni particles, the high reducibility of the Ni oxides and the interaction between metallic Ni particles and the composite oxide supports.     

Catalytic Combustion of Methane over MnOx／ZrO2-Al2O3 Catalysts

MnOx/Al2O3 and MnOx/ZrO2-Al2O3 catalysts were prepared by incipient wetness impregnation of Mn(CH3COO)2 on the corresponding supports, followed by the characterization using X-ray diffraction (XRD). temperature programmed reduction (TPR) and BET surface area techniques. The result shows the BET surface area of ZrO2-Al2O3 is lower than that of Al2O3 due to the loading of ZrO2.However tile resulted MnOx/ZrO2-Al2O3 catalyst exhibits higher activity for methane combustion than MnOx/Al2O3, because the addition of ZrO2 onto Al2O3 is beneficial for the dispersion of Mn species and the improvement of the lattice oxygen activity in MnOx. subsequently the activation of methane during combustion. The optimum loading of Zr in MnOx/ZrO2-Al2O3 is in the range of 5%-10% correlated with the calcination temperatures of catalyst supports.     

催化精馏专用填料型固体酸SO42-/ZrO2-Al2O3-Al的研究

为了研制催化精馏专用催化剂,采用铝阳极氧化法制备了Al2O3-Al一体型载体,并将活性固体超强酸SO42-/ZrO2引入到Al2O3-Al上,得到一种新型催化精馏专用填料式固体酸SO42-/ZrO2-Al2O3-Al催化剂.利用XRD、 SEM、 BET、 XPS、 NH3-TPD等手段对其进行了表征.结果表明,所制得的阳极氧化铝膜厚为56 μm, SO42-/ZrO2-Al2O3-Al固体酸具有比表面积大、酸强度适中的特点.XRD结果表明, ZrO2在Al2O3-Al上处于高度分散状态.将该固体酸用于乙酸/乙醇酯化反应中,显示出较高的催化活性,且稳定性较好.     

Ni/ZrO2催化剂上甲烷水蒸气重整反应的研究

研究了Ni/ZrO2催化剂对甲烷水蒸气重整制合成气的反应性能。考察了催化剂的还原温度、载体焙烧温度以及反应温度、原料配比和空速等对催化剂性能的影响。利用XRD、TEM、XPS等手段对催化剂的织构形貌进行了表征。研究表明，Ni/ZrO2催化剂用于甲烷水蒸气重整制合成气不仅具有较高的活性，也具有较好的稳定性。水蒸气比增加，CH4转化率增大、CO选择性下降。CH4转化率及CO选择性均随空速增大而下降。使用10%Ni/ZrO2催化剂，在650 ℃、空速1.984×104 h－1、原料气配比H2O∶CH4∶N2=2∶1∶2.67的条件下，获得CH4转化率85%、CO选择性70%的结果。     

CO Selective Oxidation in Hydrogen-Rich Gas over Copper-Series Catalysts

The performances of CO selective oxidation in hydrogen-rich gas over four catalytic systems of CuO/ZrO2, CuO/MnO2, CuO/CoO and CuO/CeO2 were compared. The reducibility of these catalysts and the effect of CuO and CeO2 molar ratio of CuO/CeO2 catalysts on the activity of selective CO oxidation are investigated by XRD and TPR methods. The results show that the catalysts with the exception of CuO/ZrO2 have the interactions between CuO and CoO, CeO2 or MnO2, which result in a decrease in the reduction temperature. Among the catalysts studied, CuO/ZrO2 catalyst shows the lowest catalytic activity while CuO/CeO2 catalyst exhibits the best catalytic performance. The CuO(10%)/CeO2 catalyst attains the highest CO conversion and selectivity at 140 and 160℃. The addition of 9% H2O in the reactant feed decreases the activity of CuO/CeO2 catalyst but increases its CO selectivity.     

柠檬酸对Ni2P/TiO2-Al2O3催化剂加氢脱硫性能的影响

采用溶胶-凝胶法制备了TiO2-Al2O3复合载体,以柠檬酸(CA)为络合剂采用浸渍法制备了Ni2P负载的TiO2-Al2O3复合载体催化剂,并用X射线衍射(XRD)、N2吸附比表面积测定、H2程序升温氢还原(H2-TPR)、程序升温氧化(TPO)、X射线光电子能谱(XPS)技术对催化剂的结构和性质进行了表征,考察了CA/Ni摩尔比对在Ni2P/TiO2-Al2O3催化剂上进行的二苯并噻吩(DBT)加氢脱硫(HDS)性能的影响.结果表明:适量的CA可以丰富催化剂的孔道,提高催化剂的比表面积.当n(CA)/n(Ni)=2:1时,催化剂的比表面积达到126.75m2·g-1,与不加CA时相比,提高了57.05m2·g-1.调节n(CA)/n(Ni)能够改善活性相的分布,改变活性相的种类;引入CA使Ni和P前驱体的还原温度明显降低,促进活性相Ni2P的生成,一定程度上能够抑制催化剂表面炭的形成和沉积,提高其稳定性.n(CA)/n(Ni)=2:1时,催化剂具有最好的加氢脱硫活性,在360°C,3.0MPa,氢油比为500(V/V),液时体积空速为2.0h-1的条件下,二苯并噻吩转化率为99.5%,可将模拟油中硫含量由2%(w)降低到0.01%(w).     

助剂Cu对Ni/γ-Al2O3催化剂低温还原性能影响

制备了一系列铜质量分数不同的CuNi/γ-Al2O3催化剂，进行了TPR和XRD表征并测定了该系列催化剂对苯加氢制环己烷的催化活性。结果表明，助剂Cu的负载量对低温（160 ℃）还原后催化剂的催化活性影响很大，在铜镍原子摩尔比为1∶1时，催化剂具有较高的催化活性和稳定性；添加铜组分可促进镍在载体表面分散，使负载NiO的还原温度降低，催化活性提高。     

纳米Cr2O3系列催化剂上CO2氧化乙烷脱氢制乙烯反应

 采用溶胶－凝胶法和共沸蒸馏法耦合技术制备了纳米Cr2O3催化剂，并采用共沉淀法和共沸蒸馏法耦合技术制备了纳米Cr2O3／Al2O3，Cr2O3／ZrO2和Cr2O3／MgO复合催化剂．应用BET，XRD，XPS，TPR和TEM等物理化学方法对催化剂的结构和物化性质进行了表征，并考察了该系列催化剂上CO2氧化乙烷脱氢制乙烯的反应性能．结果表明，纳米Cr2O3催化剂上乙烷和CO2的转化率均明显高于常规Cr2O3催化剂，但乙烯的选择性低于常规Cr2O3催化剂；纳米复合催化剂中的复合成分显著影响催化剂的催化性能．其中，10％Cr2O3／MgO纳米复合催化剂在温度为973K时，乙烷转化率和乙烯选择性分别可达到61．54％和94．79％．纳米催化剂表面Cr的还原性以及Cr6＋／Cr3＋比值是影响乙烷转化率和乙烯选择性的重要因素．     

ZrO2在Rh/γ-Al2O3催化剂中对NO催化还原反应的作用

测定了含ZrO2的Rh/γ-Al2O3催化剂上NO+C2H4和NO+C2H4+O2的反应活性,并应用TPR、XRD、BET比表面等表征了ZrO2的加入方式和晶型对Rh/γ-Al2O3催化剂活性和结构的影响。结果表明,ZrO2的加入一定程度地抑制了Rh3+与γ-Al2O3之间的相互作用和γ-Al2O3的相变,提高了催化剂的热稳定性,明显提高了850℃老化样品的NO+C2H4反应活性。对于NO+C2H4+O2反应,含ZrO2样品的选择还原活性却较低,表明反应机理不同,而且ZrO2对C2H4的深度氧化有促进作用,但老化后活性下降幅度比不含ZrO2的样品小。     

Ni2+在γ-Al2O3上的分散状态及负载型Ni/γ-Al2O3催化剂的α-蒎烯加氢活性

用X-射线衍射(XRD)、紫外-可见漫散射光谱(UV-Vis DRS)、程序升温还原(TPR)、CO化学吸附和微反测试等方法研究了Ni²⁺在γ-Al₂O₃上的分散状态和负载型Ni/γ-Al₂O₃催化剂的α-蒎烯加氢催化活性。结果表明，当Ni²⁺负载量远低于其在γ-Al₂O₃载体表面分散容量时，Ni²⁺优先嵌入载体表面四面体空位，随着Ni²⁺负载量的增加，嵌入载体表面八面体空位Ni²⁺的比例增大。由于八面体Ni²⁺易被还原为金属态Ni⁰，NiO/γ-Al₂O₃样品的还原度随Ni²⁺负载量的增加而大幅度地增加，经氢还原所得Ni/γ-Al₂O₃催化剂的CO吸附量和α-蒎烯加氢催化活性大幅度增加。对La₂O₃助剂的作用进行了研究，结果表明分散在γ-Al₂O₃上的La³⁺物种可阻止Ni²⁺嵌入γ-Al₂O₃表面四面体空位，增大了八面体Ni²⁺物种所占比例，提高了催化剂的还原度，故Ni-La₂O₃/γ-Al₂O₃催化剂催化活性高于Ni/γ-Al₂O₃催化剂。     

Effect of CeO2 on the catalytic performance of Ni/Al2O3 for autothermal reforming of methane

The effect of promoter Ce on the catalytic performance of Ni/Al2O3 catalyst for autothermal reforming of methane to hydrogen was investigated. The catalysts were characterized by X-ray diffraction （XRD）, temperature-programmed reduction （TPR）, and X-ray photoelectron spectroscopy （XPS）. The results indicated that the catalytic performance of the catalysts was improved with the addition of Ce. Ni/Ce30Al70Oδ showed the highest CH4 conversion in operation temperatures ranging from 650 ℃ to 850 ℃. At the same time, the decrease in H2/CO ratio with increasing reaction temperature was consistent with the fact that water-gas shift reaction was thermodynamically unfavorable at higher temperatures. The XRD result indicated that adding Ce to Ni/Al2O3 catalyst prevented the formation of NiAl2O4 and facilitated the formation of NiO. The formation of NiO increased the number of active sites, resulting in higher activity. Comparing the TPR profiles of Ni/Ce30Al70Oδ with Ni/Al2O3, it could be clearly observed that with the addition of Ce, the total reduction peak areas in the middle and low temperatures increased. It was most probably that the addition of Ce inhibited the stronger interaction between Ni and Al2O3 to form the phase of NiAl2O4, and favored the formation of the strong interaction between NiO species and CeO2. Therefore, the addition of Ce to the Ni/Al2O3 catalyst increased the active surface that promoted the activity of the catalyst.     

Pt/γ-Al2O3/CexZr1-xO2催化剂低温催化燃烧去除饮食油烟

以CexZr1-xO2固溶体做载体, 制备了系列Pt/γ-Al2O3/CexZr1-xO2催化剂(x=1, 0.75, 0.5, 0.25, 0). 应用Brunauer-Emmet-Teller (BET)比表面积分析、X射线衍射(XRD)和H2程序升温还原(H2-TPR)等手段对催化剂进行相关表征, 并系统研究了催化剂在饮食油烟催化燃烧中的催化活性. BET结果表明催化剂的比表面积随Ce/Zr摩尔比的减小而减小. XRD结果表明贵金属Pt很好地分散在氧化铝和CexZr1-xO2固溶体上. H2-TPR结果发现催化剂Pt/γ-Al2O3/Ce0.5Zr0.5O2的还原峰面积最大且氧离子的流动性最好. 催化活性研究结果表明Pt负载在CexZr1-xO2固溶体上有利于油烟的催化燃烧, 降低了反应温度. 随着CexZr1-xO2固溶体中Ce/Zr摩尔比的变化, 催化剂的活性顺序为Pt/γ-Al2O3/Ce0.5Zr0.5O2>Pt/γ-Al2O3/Ce0.25Zr0.75O2>Pt/γ-Al2O3/Ce0.75Zr0.25O2>Pt/γ-Al2O3/CeO2>Pt/γ-Al2O3/ZrO2.     

ZrO2-TiO2-CeO2的制备及其在NH3选择性催化还原NO中的应用

采用共沉淀法制备了载体材料TiO2、ZrO2-TiO2及ZrO2-TiO2-CeO2, 并利用X射线衍射(XRD)实验、比表面积测定(BET)、程序升温脱附(NH3-TPD)、储氧性能测定(OSC)及程序升温还原(H2-TPR)等方法对三种载体材料进行了表征. 结果表明, ZrO2-TiO2-CeO2具有较多的表面强酸位, 并具有一定的储氧性能和较强的氧化还原性能. 以三种材料为载体, 制备了质量分数分别为1%、9%的V2O5、WO3的整体式催化剂. 研究了三种催化剂在富氧条件下用NH3选择性催化还原NO的催化性能. 结果表明, 以ZrO2-TiO2-CeO2为载体的催化剂在反应空速为10000 h-1, 275 ℃时, NO的转化率接近100%, 具有最好的催化活性,并有良好的应用前景。     

甲烷部分氧化Ni催化剂及助剂的研究

考察了不同Ni担载量的Ni／a－Al_2O_3催化剂的催化性能，以8％Ni（质量分数）最佳．XRD分析表明，8％Ni催化剂表面NiO颗粒最小．TPR分析表明，催化剂表面主要有两种不同化学环境的NiO，当Ni担载量超过12％时，表面开始出现“游离态”NiO，这部分NiO易使催化剂积碳．添加稀土Ce有利于提高Ni催化剂的活性、选择性和稳定性，并对Ce的助剂效应作了研究．     

Selective catalytic methanation of CO in hydrogen-rich gases over Ni/ZrO2 catalyst

Ni/ZrO2 catalysts were prepared by the incipient-wetness impregnation method and were investigated in activity and selectivity for the selective catalytic methanation of CO in hydrogen-rich gases with more than 20 vol% CO2. The result showed that Ni loadings significantly influenced the performance of Ni/ZrO2 catalyst. The 1.6 wt% Ni loading catalyst exhibited the highest catalytic activity among all the catalysts in the selective methanation of CO in hydrogen-rich gas. The outlet concentration of CO was less than 20 ppm with the hydrogen consumption below 7%, at a gas-hourly-space velocity as high as 10000 h-1 and a temperature range of 260 °C to 280 °C. The X-ray diffraction （XRD） and temperature programmed reduction （TPR） measurements showed that NiO was dispersed thoroughly on the surface of ZrO2 support if Ni loading was under 1.6 wt%. When Ni loading was increased to 3 wt% or above, the free bulk NiO species began to assemble, which was not favorable to increase the selectivity of the catalyst.