Synthesis of nano hydroxyapatite powder that simulate teeth particle morphology and composition

A simple sol–gel precipitation technique to synthesize nano hydroxyapatite (HA) particles (30 nm) that show similar morphology, size and crystallinity to HA crystals of human teeth is reported. Calcium nitrate tetrahydrate and potassium dihydrogenphosphate were used as calcium and phosphorus precursors, respectively. Double distilled water was used as a diluting media for HA sol preparation and ammonia was used to adjust the pH to 11. After aging, the HA gel was dried at 40 °C and calcined to different temperatures ranging from 200 to 600 °C. The dried and calcined powders were characterized for phase composition using X-ray diffractrometry, and Fourier transform infra-red spectroscopy. The particle size and morphology was studied using Transmission electron microscopy. The particle size distribution analysis of HA powders showed skewed distribution plot. The phase and particle characterization studied above showed that HA calcined at 600 °C simulate HA crystals of teeth.     

Dimensional evolution of silicon nanowires synthesized by Au–Si island-catalyzed chemical vapor deposition

This study explores the nucleation and morphological evolution of silicon nanowires (Si-NWs) on Si (0 0 1) and (1 1 1) substrates synthesized using nanoscale Au–Si island-catalyzed rapid thermal chemical vapor deposition. The Au–Si islands are formed by Au thin film (1.2–3.0 nm) deposition at room temperature followed by annealing at 700 °C, which are employed as a liquid-droplet catalysis during the growth of the Si-NWs. The Si-NWs are grown by exposing the substrates with Au–Si islands to a mixture of gasses SiH₄ and H₂. The growth temperatures and the pressures are 500–600 °C and 0.1–1.0 Torr, respectively. We found a critical thickness of the Au film for Si-NWs nucleation at a given growth condition. Also, we observed that the dimensional evolution of the NWs significantly depends on the growth pressure and temperature. The resulting NWs are 30–100 nm in diameter and 0.4–12.0 μm in length. For Si (0 0 1) substrates 80% of the NWs are aligned along the 1 1 1 direction which are 30° and 60° with respect to the substrate surface while for Si (1 1 1) most of the NWs are aligned vertically along the 1 1 1 direction. In particular, we observed that there appears to be two types of NWs; one with a straight and another with a tapered shape. The morphological and dimensional evolution of the Si-NWs is significantly related to atomic diffusion kinetics and energetics in the vapor–liquid–solid processes.     

Grain size refinement and magnetostriction of ferromagnetic shape memory Fe–Pd–Rh alloys

This paper reports the forging of bulk ferromagnetic shape memory (FSM) Fe–30Pd–2Rh (at%) alloys to a 40% reduction in thickness, followed by thermal annealing at 950–1100 °C for various times and quenching in ice brine to induce recrystallization (i.e. grain size refinement). Investigation with the Vickers microhardness test reveals that the process of recrystallization results in increased ductility of the fine grains. TEM and magnetostriction investigations reveal two kinds of twins contained in the strain-forged sample annealed at 950 °C for 3 h, i.e. deformation and transformation twins, and these twins also improved a higher magnetostriction as well as ductility in the alloys that may be useful in magneto-mechanical applications (such as microactuator or spring).     

From Zn microspheres to hollow ZnO microspheres: A simple route to the growth of large scale metallic Zn microspheres and hollow ZnO microspheres

Large scale metallic Zn microspheres and hollow ZnO microspheres are synthesized by thermal evaporation and vapor transport by heating a ZnO/graphite mixture at 1000 °C. Firstly, metallic Zn microspheres are fabricated with diameters in the range of 1–10 μm. The Zn microspheres are then annealed at 600 °C in air, which form hollow semiconducting ZnO microspheres. EDX and XRD spectra reveal that the oxidized material is indeed ZnO. Room temperature photoluminescence spectra of the oxidized material show a sharp peak at 380 nm and a wider broad peak centered at 490 nm. This growth mechanism is discussed and further investigated for other metallic and metal oxide microstructures.     

Effect of the synthesis route on the structural properties and shape of the indium oxide (In2O3) nano-particles

Nano-crystalline indium oxide (In₂O₃) particles have been synthesized by sol–gel and hydro-thermal techniques. A simple hydro-alcoholic solution consisting indium nitrate hydrate and citric acid (in sol–gel method) and 1, 4-butandiol (in hydro-thermal method) have been utilized. The structural properties of indium oxide nano-powders annealed at 450 °C (for both methods) have been characterized by the X-ray diffraction (XRD), transmission electron microscopy (TEM), scanning electron microscopy (SEM), and specific surface area (SSA) analysis. Structural analysis of the samples shows cubic phase in sol–gel and cubic-hexagonal phase mixture in hydro-thermally prepared particles. The nano-particles prepared by sol–gel method have nearly spherical shape, whereas hydro-thermally-made ones display wire- and needle-like shape in addition to the spherical shape. The obtained In₂O₃ nano-particles surface areas were 23.2 and 55.3 in sol–gel and hydro-thermal methods, respectively. The optical direct band gap of In₂O₃ nano-particles were determined to be 4.32 and 4.24 eV for sol–gel and hydro-thermal methods, respectively. These values exhibit 0.5 eV blue shift from that the bulk In₂O₃ (3.75 eV), which is related to the particle size reduction and approaching the quantum confinement limit of nano-particles.     

Epitaxial growth of highly transparent and conducting Sc-doped ZnO films on c-plane sapphire by sol–gel process without buffer

Highly transparent and conductive scandium doped zinc oxide (ZnO:Sc) films were deposited on c-plane sapphire substrates by sol–gel technique using zinc acetate dihydrate [Zn(CH₃COO)₂·2H₂O] as precursor, 2-methoxyethanol as solvent and monoethanolamine as a stabilizer. The doping with scandium is achieved by adding 0.5 wt% of scandium nitrate hexahydrate [(ScNO₃·6H₂O)] in the solution. The influence of annealing temperature (300–550 °C) on the structural, optical and electrical properties was investigated. X-ray Diffraction study revealed that highly c-axis oriented films with full-width half maximum of 0.16° are obtained at an annealing temperature of 400 °C. The surface morphology of the films was judged by SEM and AFM images which indicated formation of grains. The average transmittance was found to be above 92% in the visible region. ZnO:Sc film, annealed at 400 °C exhibited minimum resistivity of 1.91 × 10⁻⁴ Ω cm. Room-temperature photoluminescence measurements of the ZnO:Sc films annealed at 400 °C showed ultraviolet peak at 3.31eV with a FWHM of 11.2 meV, which are comparable to those found in high-quality ZnO films. Reflection high-energy electron diffraction pattern confirmed the epitaxial nature of the films even without introducing any buffer layer.     

Conversion of egg shell membrane to inorganic porous CexZr1−xO2 fibrous network

The binary system CeO₂–ZrO₂ is thermally stable and has superior reduction–oxidation properties. It has been commonly used in the three-way catalytic converters for automobiles. In this work, an inorganic biomorphic porous Ce_xZr_1−xO₂ fibrous network was successfully synthesized by using the egg shell membrane (ESM) as templates, and its morphology was a perfect replica of the original ESM. The synthesis involved a simple infiltration and calcination process. A fresh ESM was peeled from a chicken egg shell. It was soaked in a Ce(NO₃)₃ and Zr(NO₃)₄ mixture before it was calcined at 700 °C in ambient environment. The fibers in the biomorphic network had diameter ranged from 1 to 4 μm, and they were composed of Ce_xZr_1−xO₂ nanocrystallites having an average grain size of 10 nm.     

Nanoscale anglesite growth on the celestite (0 0 1) face

In situ atomic force microscopy (AFM) was used to study the growth behaviour of anglesite (PbSO₄) monolayers on the celestite (0 0 1) face. Growth was promoted by exposing the celestite cleavage surfaces to aqueous solutions that were supersaturated with respect to anglesite. The solution supersaturation, β_ang, was varied from 1.05 to 3.09 (where β_ang = a(Pb²⁺) · a(SO₄²⁻)/K_sp,ang). In this range of supersaturation, two single anglesite monolayers (3.5 Å in height each) from pre-existent celestite steps were grown. However, for solution supersaturation β_ang < 1.89 ± 0.06, subsequent multilayer growth is strongly inhibited. AFM observations indicate that the inhibition of a continuous layer-by-layer growth of anglesite on the celestite (0 0 1) face is due to the in-plane strain generated by the slight difference between the anglesite and celestite lattice parameters (i.e. the linear misfits are lower than 1.1%). The minimum supersaturation required to overcome the energy barrier for multilayer growth gave an estimate of the in-plane strain energy: 11.4 ± 0.6 mJ/m²_. Once this energy barrier is overcome, a multilayer Frank–Van Der Merwe epitaxial growth was observed.     

Nucleation, growth and morphology of Co thin films on Ag(1 1 0)

Scanning tunneling microscopy (STM) experiments reveal that Co growth on Ag(1 1 0), at coverages of Co < 1 ML and low substrate temperatures (150 K), involves a concomitant insertion of Co into the top Ag layer and exchange of Ag out onto the surface. At 300 K, coverages of Co > 1 ML gives rise to a 3D nanocluster growth on the surface, with the clusters covered by Ag. Depending slightly on coverage, the clusters have a typical diameter of 3 nm and a height of 0.4 nm. Upon annealing to 500 K, major changes are observed in the morphology of the surface. STM and AES show that there is a reduction of the number of Co islands on the surface, partly due to subsurface Co cluster migration and partly due to sintering into larger clusters.     

The electrodeposition of copper onto UHV-prepared GaAs(0 0 1) surfaces

Synchrotron surface X-ray diffraction has been used to investigate in situ the morphology and epitaxy of monolayer amounts of copper electrodeposited from aqueous electrolyte onto ultra-high vacuum prepared, smooth, Ga- or As-terminated GaAs(0 0 1) surfaces. The fcc lattice of the epitaxial Cu islands is rotated by 5° and tilted by about 9° with respect to the GaAs substrate lattice, leading to eight symmetry equivalent domains of Cu islands terminated by {1 1 1} facets.     

Cholesterol binding to amyloid-beta fibrils: a TEM study

There is increasing interest in the role of brain cholesterol in Alzheimer's disease and the contribution of cholesterol to the formation of amyloid plaques. This paper presents a TEM study showing the binding of soluble 10 nm diameter cholesterol-PEG 600 micelles to amyloid-β_1-42 (Aβ_1-42) fibrils formed either in the presence of this cholesterol derivative or to preformed fibrils generated under four different fibrillogenesis conditions. Specimens negatively stained with uranyl acetate revealed that during 24 h fibrillogenesis at 37 °C the cholesterol-PEG micelles bound periodically to Aβ_1-42 protofibrils and apparently also formed a thin smooth unbroken coating on mature double helical fibrils. Preformed protofibrils, generated in water alone or in the presence of 0.1 mM cupric sulphate, also exhibited periodic binding of cholesterol-PEG micelles, indicating the inherently helical nature of the protofibril. Double helical mature Aβ_1-42 fibrils, generated in the presence of cholesterol microcrystals or hydrogen peroxide (1 mM), bound cholesterol-PEG micelles with no immediately apparent regularity and without creating a smooth coating. The differing capacities of the Aβ_1-42 protofibrils and mature double helical fibrils to bind cholesterol-PEG 600 may indicate differences in the accessibility of the micellar cholesterol to the purported Aβ_17-21 hydrophobic cholesterol-binding motif on the fibril surfaces.     

Bragg grating writing through the polyimide coating of high NA optical fibres with femtosecond IR radiation

Bragg gratings are written with ultrafast 800 nm radiation and a phase mask through the polyimide polymer coatings of commercially available high NA fibres that are both unloaded and loaded with high pressure hydrogen gas. For polyimide coated fibres with very high germanium core concentrations, index modulations greater than 1 × 10⁻⁴ are induced. Stable core index modulations 60% of their original value were present after 115 h at 500 °C.     

Microwave dielectric properties of (1 − x)(Mg0.95Co0.05)TiO3–x(Na0.5La0.5)TiO3 ceramic system

The microstructures and the microwave dielectric properties of the (1 − x)(Mg_0.95Co_0.05)TiO₃–x(Na_0.5La_0.5)TiO₃ ceramic system were investigated. Two-phase system was confirmed by the XRD patterns and the EDX analysis. A co-existed second phase (Mg_0.95Co_0.05)Ti₂O₅ was also detected. The microwave dielectric properties are strongly related to the density and the matrix of the specimen. A new microwave dielectric material 0.88(Mg_0.95Co_0.05)TiO₃–0.12(Na_0.5La_0.5)TiO₃, possessing an excellent combination of dielectric properties: ε_r  22.36, Q × f  110,000 GHz (at 9 GHz), τ_f  2.9 ppm/°C), is proposed as a candidate dielectric for GPS patch antennas.     

In-situ TiC particle reinforced Ti–Al matrix composites: Powder preparation by mechanical alloying and Selective Laser Melting behavior

Mechanical alloying of Ti–Al–graphite elemental powder mixture was performed to synthesize nanocomposite powder with Ti(Al) solid solution matrix reinforced by in-situ formed TiC particles. The evolutions in phases, microstructures, and compositions of milled powders with the applied milling times were investigated. It showed that with increasing the milling time, the starting irregularly shaped powder underwent a successive change in its morphology from a flattened shape (10 h) to a highly coarsened spherical one (15 h) and, eventually, to a fine, equiaxed and uniform one (above 25 h). The prepared TiC/Ti(Al) composite powder was nanocrystalline, with the estimated average crystallite size of 12 nm and of 7 nm for Ti(Al) and TiC, respectively. Formation mechanisms behind the microstructural development of powders were elucidated. The Ti(Al) solid solution is formed through a gradual and progressive solution of Al into Ti lattice. The formation of TiC is through an abrupt, exothermic, and self-sustaining reaction between Ti and C elements. Selective Laser Melting (SLM) of as-prepared TiC/Ti(Al) composite powder was performed. The TiC particle reinforced TiAl₃ (a major phase) and Ti₃AlC₂ (a minor phase) matrix composite part was obtained after SLM. Although a slight grain growth occurred as relative to as-milled powder, the SLM processed composites still exhibited a refined microstructure.     

Catalyst-free synthesis and luminescence of aligned ZnO nanorods

Quasi-aligned undoped ZnO nanorods with diameter in the range 100–300 nm and length of several micrometers have been grown catalyst-free on Si(1 0 0) wafer in a one-step process by direct heating of Zn powders. All nanowires are single crystals and are aligned vertically to the substrate surface with c-axis preferred orientation. XRD, HRTEM and Raman studies revealed that the ZnO nanorods have wurtzite phase, are highly crystalline and well aligned with the lattice parameters a=0.32 nm and c=0.52 nm. The PL spectra measured at different temperatures are dominated by excitonic emission at 380 nm and less intense below band gap emission band centered at 520 nm.     

Combustion of nano-aluminum and liquid water

An experimental investigation on the combustion behavior of nano-aluminum (nAl) and liquid water has been conducted. In particular, linear and mass-burning rates of quasi-homogeneous mixtures of nAl and liquid water as a function of pressure, mixture composition, particle size, and oxide layer thickness were measured. This study is the first reported self-deflagration on nAl and liquid water without the use of any additional gelling agent. Steady-state burning rates were obtained at room temperature (25 °C) using a windowed vessel for a pressure range of 0.1–4.2 MPa in an argon atmosphere, particle diameters of 38–130 nm, and overall mixture equivalence ratios () from 0.5 to 1.25. At the highest pressure studied, the linear burning rate was found to be 8.6 ± 0.4 cm/s, corresponding to a mass-burning rate per unit area of 6.1 g/cm² s. The pressure exponent at room temperature was 0.47, which was independent of the overall mixture equivalence ratio for all of the cases considered. The mass-burning rate per unit area increased from 1.0 to 5.8 g/cm² s for an equivalence ratio range of 0.5–1.25. It varied inversely to particle diameter, increasing by 157% when the particle diameter was decreased from 130 to 50 nm at  = 1.0.     

Initial nucleation of Au on the R45° reconstructed Fe3O4(0 0 1) surface

The initial nucleation of Au onto the R45° reconstructed Fe₃O₄(0 0 1) surface has been studied using scanning tunnelling microscopy. Au clusters are formed, with a typical lateral dimension of 0.9 nm. The measured corrugation height of the clusters, 0.1 nm, suggests that they are a single atomic layer in height. The clusters nucleate on a specific surface site, which lies at the centre of a R45° reconstructed unit cell. The size and spatial distribution of the Au clusters formed is shown to strongly correlate to the symmetry and periodicity of the reconstructed magnetite surface. It is also shown that even when the clusters are in close proximity they still only occupy this single nucleation site, and thus maintain the periodicity of the substrate. We relate the order and stability of this system to the fact that magnetite (0 0 1) is polar, and suggest that such surfaces offer ideal templates for self-assembly due to the stability of their polarity induced reconstructions.     

Time-of-flight distributions of HD molecules abstracted at a Si(1 0 0) surface

We study the dynamics of D abstraction by 0.05 eV H atoms on a Si(1 0 0) surface. Time-of-flight (TOF) distributions of the abstracted HD molecules are measured using a quasi-random chopper/cross-correlation method. The measured TOF distribution is found to be broad and fast. The distribution is decomposed into two components being related to direct abstraction (ABS) and adsorption-induced-desorption (AID), which were revealed in the kinetics studies. The best curve fits yield mean kinetic energies of 1.15 ± 0.20 eV and 0.33 ± 0.05 eV for the ABS and AID components, respectively. Dynamics and kinetics of hydrogen abstraction at Si(1 0 0) surfaces are consistently understood.     

X-ray characterization and phase transformation kinetics of ball-mill prepared nanocrystalline Mg–Zn-ferrite at elevated temperatures

Nanocrystalline Mg–Zn-ferrite is prepared by ball milling the stoichiometric powder mixture of MgO, ZnO and α-Fe₂O₃. A non-stoichiometric ferrite phase is noticed to form after 3 h of milling when particles of starting materials became nano-sized. After 25 h of milling, stoichiometric ferrite phase is formed with 9 nm particle size. Post annealing study of ball-milled sample reveals that the nanocrystalline ferrite phase is stable up to 873 K and then starts to decompose into individual starting phases. However, heat treatment of unmilled stoichiometric powder mixture even at 1473 K for 1 h duration does not result in formation of stoichiometric Mg–Zn-ferrite phase.     

Structure and reaction pathways of methyl lactate on Pd(1 1 1)

The adsorption and reaction of methyl lactate (CH₃CH(OH)COOCH₃) is studied in ultrahigh vacuum on a Pd(1 1 1) surface using temperature-programmed desorption (TPD) and reflection–absorption infrared spectroscopy (RAIRS). Methyl lactate reacts at relatively low temperatures (220 K) by O–H bond scission. This intermediate can either react with hydrogen to reform methyl lactate at 280–300 K or undergo β-hydride elimination to form flat-lying methyl pyruvate. This decomposes to form acetyl and methoxy carbonyl species as found previously following methyl pyruvate adsorption on Pd(1 1 1). These species predominantly react to form carbon monoxide, methane and hydrogen.