Determination of selenium(IV) and selenium(VI) in natural water samples by neutron activation analysis after chemical pre-collection

Neutron activation analysis using shortlived^77mSe (T=17.5 s) preceded by chemical pre-collection of Se on activated carbon (AC) has been applied to the fractional determination of Se(IV) and Se(VI) in natural water samples such as river water and sea water. Two chemical procedures were adopted: adsorption of Se(IV)/Bismuthiol-II complex on AC and adsorption of Se(VI)/Bismuthiol-II on AC after reduction of Se(VI) to Se(IV). It was shown that Se(IV) and Se(VI) can be determined at a <g l^–1 (ppb) level in natural waters by the present method.     

Microscopic investigations of the Cr(VI) uptake mechanism of living Ochrobactrum anthropi

A basic understanding related to the immobilization of chromium by bacteria is essential for chromate pollutant remediation in the environment. In this work, we studied the Cr(VI) uptake mechanism of living Ochrobactrum anthropi and the influence of a bacterial culture medium on the Cr-immobilization process. It was found that the Cr-immobilization ratio of bacteria in Tris-HCl buffer is higher than in LB medium. X-ray photoelectron spectroscopy (XPS) and electron paramagnetic resonance (EPR) analysis revealed that the chromium accumulated on bacteria were mostly in Cr(III) states. Scanning electron microscopy (SEM) and atomic force microscopy (AFM) observations showed that noticeable Cr(III) precipitates were accumulated on bacterial surfaces. AFM roughness analysis revealed that the surface roughness of bacteria increased greatly when the bacteria-Cr(VI) interaction was in Tris-HCl buffer rather than in LB solution. Transmission electron microscopy (TEM) thin section analysis coupled with energy-dispersive X-ray spectroscopy showed that Cr(III) is also distributed in bacterial inner portions. A chromium-immobilization mechanism considering the participation of both bacterial inner portions and bacterial surfaces of living Ochrobactrum anthropi was proposed, whereas the bacterial surface was the dominant part of the immobilization of Cr(III). This work also proved that the control of Cr immobilization by living Ochrobactrum anthropi could be achieved via adjusting the bacterial culture medium.     

Preconcentration of inorganic selenium species (Se (IV) and Se (VI)) in an alumina filled microcolumn and on-line determination by hydride generation atomic absorption spectrometry

A flow injection system has been developed consisting of on-line preconcentration of selenium species in a microcolumn filled with activated alumina, reduction of Se(VI) to Se(IV) and determination by HG-AAS. When 0.01 mol/L HNO₃ is used both as carrier and activation reagent for the alumina microcolumn, up to 150 ng of Se(IV) and Se(VI) can be preconcentrated and quantitatively eluted by 500 L of 2 mol/L NH₃. The preconcentration factor is 50 when 25 mL of sample is used. The detection limit is about 6 ng/L, the precision is 5% for low concentrations such as 150 ng/L and 3% at high concentrations such as 120 ng/mL. The proposed method is suitable for natural water samples and inorganic Se speciation can be performed by determining Se(IV) and total selenium [Se(VI) is evaluated from the difference].     

Kinetic-spectrophotometric determination of selenium in natural water after preconcentration of elemental selenium on activated carbon

A simple, accurate, sensitive and selective method is described for rapid determination of ultra-trace quantities of selenium. Selenium (IV) was collected on activated carbon after reduction to elemental Se by l-ascorbic acid. The collected selenium was then determined based on its accelerating effect on the oxidation reaction of methyl orange with bromate in acidic media. Total amount of Se(IV) and Se(VI) were collected on AC after their reduction by hydrazine. Se(IV), Se(VI) and total selenium could be determined by the method. Selenium in the range 10-10 000 ng could be determined by the method. The method was used to the determination of Se(IV), Se(VI) and total selenium in natural water with satisfactory results.     

Determination of arsenic(III), arsenic(V), antimony(III), antimony(V), selenium(IV) and selenium(VI) by extraction with ammonium pyrrolidinedithiocarbamate—methyl isobutyl ketone and electrothermal atomic absorption spectrometry

The solution conditions and other parameters affecting the ammonium pyrrolidine-dithiocarbamate—methyl isobutyl ketone extraction system for graphite-furnace atomic absorption spectrometric determination of As(III), As(V), Sb(III), Sb(V), Se(IV) and Se(VI) were studied in detail. The solution conditions for the single or simultaneous extraction of As(III), Sb(III) and Se(IV) were not critical. Arsenic(V) and Se(VI) were not extracted over the entire range of pH and acidity studied. Antimony(V) was extracted only in the acidity range 0.3—1.0 M HCl. Simultaneous extraction of total arsenic and total antimony was possible after reduction of As(V) with thiosulphate. Interference studies are also reported.     

One-pot synthesis of graphene oxide and Ni-Al layered double hydroxides nanocomposites for the efficient removal of U(VI) from wastewater

Graphene oxide and Ni-Al layered double hydroxides(GO@LDH) nanocomposites were synthesized via a one-pot hydrothermal process,and characterized by X-ray diffraction(XRD),Fourier transformed infrared spectroscopy(FTIR),scanning electron microscopy(SEM),transmission electron microscopy(TEM),X-ray photoelectron spectroscopy(XPS) and Raman spectroscopy in detail.The exploration of U(VI) sorption on GO@LDH surface was performed as a function of ionic strength,solution pH,contact time,U(VI) initial concentrations and temperature.Results of Langmuir isotherms showed that the sorption capacity of GO@LDH(160 mg/g) was much higher than those of LDH(69 mg/g) and GO(92 mg/g).The formed surface complexes between surface oxygen-containing functional groups of GO@LDH and U(VI) turned out to be the interaction mechanism of U(VI) with GO@LDH.According to the thermodynamic studies results,the sorption interaction was actually a spontaneous and endothermic chemical process.The sorption isotherms were better fitted with the Langmuir model compared with other models,which suggested the interaction was mainly dominated by mono layer coverage.The GO@LDH nanocomposites provide potential applications as adsorbents in the enrichment of radionuclides from wastewater in nuclear waste management and environmental remediation.     

Characterization of self-assembled monolayers of thiols on Au(111)

Self-assembled monolayers (SAMs) of n-butanethiol, n-dodecanethiol and their equimolar mixture on Au(111) were prepared and characterized by ellipsometry, contact angle measurement, scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS) and atomic force microscopy (AFM). Results revealed that these SAMs are oriented ultrathin films with the thickness of nanometer scale, and the SAMs were influenced by the molecular chain length, the lattice orientation and cleanliness of the substrates. The surface of the longer chain SAM is hydrophobic. The thicknesses of three SAMs of n-butanethiol, n-dodecanethiol and their mixture revealed by ellipsometry and XPS are about 0.59 - 0.67nm, 1.60- 1.69 nm and 1.23 - 1.32nm, respectively. AFM images further demonstrated that the SAM formed by the mixture has some microdomains with two different thicknesses.     

Stability of selenium and its speciation analysis in water using automatic system separation and HR-ICP-MS measurement

A simple and convenient method has been developed for the pre-concentration and separation of inorganic selenium species from environmental water samples using anion exchange chromatographic column combined with high resolution inductively coupled plasma mass spectrometry (HR-ICP-MS) measurement. ⁷⁵Se(IV) and ⁷⁵Se(VI) were prepared and used as tracers during the experiments. The volatility of selenium during solution evaporation was investigated to establish a reliable water samples pretreatment procedure. The parameters which affect the uptake of Se(IV) and Se(VI) on Dowex1 × 8 resin was optimized and the procedure for Se(IV) and Se(VI) separation was proposed. Both Se(IV) and Se(VI) are retained on the column in natural or alkaline solution with high distribution coefficient. The successive gradient elution of pre-concentrated species of selenium with HNO₃ solution allows to differentiate between them. Se(IV) and Se(VI) finally were eluted with 0.05 mol/L HNO₃ and 5.0 mol/L HNO₃, respectively. The proposed method has been successfully verified using the certified reference materials (CRMs) of real water samples, and spiked recoveries for real samples were 98%-104% with 5% relative standard deviations (RSDs). The developed procedure is proved to be reliable and can be used for the rapid determination of selenium species in environmental water samples.     

A nanocomposite consisting of MIL-101(Cr) and functionalized magnetite nanoparticles for extraction and determination of selenium(IV) and selenium(VI)

A metal-organic framework nanocomposite was synthesized and applied to speciation analysis of Se(IV) and Se(VI). The sorbent is composed of MIL-101(Cr) and magnetite nanoparticles modified with dithiocarbamate. It is capably of selectively extracting Se(IV) at pH?=?1.85, while Se(VI) remains in solution. The total amount of selenium can then be determined by reducing Se(VI) to Se(IV) and also extracting it. The extraction parameters were optimized by employing design-of-experiments methodology. Selenium was then quantified by electrothermal AAS. Figures of merit include (a) a 10 ng·L^?1 limit of detection, (b) a linear response in the 30 ng·L^?1 to 10 μg·L^?1 concentration range, and (a) a relative standard deviation of <11.5% for Se(IV). The method was validated by analyzing certified reference materials (water and tomato leaves). It was also applied to the speciation analysis of Se(IV) and Se(VI) in (spiked) water samples and of total selenium in agricultural samples.

Open image in new window

Graphical abstract Schematic of the synthesis of a metal-organic framework nanocomposite for speciation analysis of Se(IV) and Se(VI). The sorbent is composed of MIL-101(Cr) and magnetite nanoparticles modified with dithiocarbamate. Selenium can be quantified by electrothermal AAS with a 10 ng L^?1 detection limit.

     

Capillary electrophoresis on-line coupled with hydride generation-atomic fluorescence spectrometry for speciation analysis of selenium

A new method for speciation analysis of two inorganic selenium species was developed by on-line coupling of capillary electrophoresis (CE) with hydride generation-atomic fluorescence spectrometry (HG-AFS) and on-line conversion of Se(VI) to Se(IV). Baseline separation of Se(VI) and Se(IV) was achieved by CE in a 50 cm x 75 microm inside diameter (ID) fused-silica capillary at -20 kV using a mixture of 15 mmol.L(-1) NaH2PO4 and 0.5 mmol.L(-1) cetyltrimethylammonium bromide (pH 7.5) as electrolyte buffer. Se(VI) was on-line reduced to Se(IV) by mixing the CE effluent with concentrated HCl. The precision (relative standard deviation, RSD, n=7) ranged from 0.7 to 1.3% for migration time, 6.4 to 3.7% for peak height response, and 5.9 to 6.1% for peak area for the two selenium species at the 500 microg.L(-1) (as Se) level. The detection limits were 33 and 25 microg.L(-1) (as Se) for Se(VI) and Se(IV), respectively. The recoveries of the two selenium species in five locally collected water samples ranged from 88 to 114%. The developed method was applied to speciation analysis of inorganic selenium species in spiked natural water samples.     

Separation and preconcentration of Se(IV)/Se(VI) species by selective adsorption onto nanometer-sized titanium dioxide and determination by graphite furnace atomic absorption spectrometry

A simple and sensitive method for the selective determination of Se(IV) and Se(VI) in natural water and sludge samples through an adsorptive process on a nanometer-sized TiO(2) (anatase) was developed. The conditions for quantitative and reproducible preconcentration, elution, and subsequent GFAAS determination were established. The proposed method gave a concentration factor of 50 for a 100 mL sample volume, characterized by high precision, high reproducibility, and direct determination of Se(IV)/Se(VI). The detection limits (3 sigma, n=11) were 4.7ng L(-1) for Se(IV) and 6.3ng L(-1) for Se(VI); the precision (relative standard deviation) was 0.7% for Se(IV) and 0.9% for Se(VI) at the 0.5microg L(-1) level.     

Differential determination of selenium(IV) and selenium(VI) with sodium diethyldithiocarbamate, ammonium pyrrolidinedithiocarbamate and dithizone by atomic-absorption spectrophotometry with a carbon-tube atomizer

The extraction behaviour of selenium(IV) and selenium(VI) with sodium diethyldithiocarbamate, ammonium pyrrolidinedithiocarbamate and dithizone in organic solvents has been investigated by means of flameless atomic-absorption spectrophotometry with a carbon-tube atomizer. The selective extraction of selenium(IV) and differential determination of selenium(IV) and selenium(VI) have been developed. With sodium diethyldithiocarbamate and carbon tetrachloride, when the aqueous phase/organic solvent volume ratio is 5 and the injection volume in the carbon tube is 20 microl, the sensitivity for selenium is 0.4 ng/ml for 1% absorption. The relative standard deviations are ca. 3%. Interference by many metal ions can he prevented by masking with EDTA. The proposed methods have been applied satisfactorily to determination of Se(IV) and Se(VI) in various types of water.     

A chemical, morphological, and electrochemical (XPS, SEM/EDX, CV, and EIS) analysis of electrochemically modified electrode surfaces of natural chalcopyrite (CuFeS2) and pyrite (FeS2) in alkaline solutions

Electrodic surfaces of natural chalcopyrite and natural pyrite minerals (El Teniente mine, Chile) have been studied by cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), X-ray photoelectron spectroscopy (XPS), and scanning electron microscopy including microanalysis (SEM/EDX). For comparison, fractured and polished mineral surfaces were also studied by XPS. In both electrodes, the formation of Fe(III) species containing oxygen were detected and Cu(II) species containing oxygen were additionally detected for chalcopyrite at advanced oxidation states. The presence of Cu(II) species containing oxygen was not detected by XPS for the initial oxidation states of the chalcopyrite. For pyrite, the present results do not allow confirmation of the presence of polysulfurs such as have been previously proposed. In both minerals, the measurements of SEM and EDX show relevant alterations in the respective surfaces when different potential values were applied. The chalcopyrite surface shows the formation of protrusions with a high concentration of oxygen. The pyrite surface shows a layer of modified material with high oxygen content. The modifications detected by XPS, SEM, and EDX allowed the explanation of the complexity of the equivalent circuit used to simulate the experimental EIS data. At high oxidation states, both minerals showed a pseudoinductive loop in the equivalent circuit, which was due to the active electrodissolution of the minerals which takes place through a surface film previously formed.     

Determination of selenium(IV) by catalytic stripping voltammetry with an in situ plated bismuth-film electrode.

A very sensitive and simple method is presented for the determination of Se(IV) by Osteryang square-wave cathodic stripping voltammery (OSWCSV). The method is based on the reduction of Se(IV) with Bi(III) onto an edge-plane type of pyrolytic graphite substrate, followed by a cathodic potential scan. OSWCSV studies indicate that the reduced selenium produced a distinct catalytic hydrogen wave at -1150 mV vs. Ag/AgCl. The peak height of the catalytic hydrogen wave was directly proportional to the initial Se(IV) concentration in the ranges of 0.1 - 1.0 and 1.0 - 20.0 microg L(-1) (correlation coefficients 0.9800 and 0.9901, respectively) when the optimized parameters were used. A 3sigma detection limit of 0.025 microg L(-1)0 Se(IV) was obtained at 30 s deposition time. The relative standard deviation was 4.0% on replicate runs (n = 12) for the determinations of 0.10 microg L(-1) Se(IV). Analytical results of natural water samples demonstrate that the proposed method is applicable to speciation analysis of Se(IV) and Se(VI).     

Microwave assisted reduction of Se(VI) to Se(IV) and determination by HG/FI-ICP/MS for inorganic selenium speciation

Speciation of inorganic selenium using hydride generation method is a widespread analytical method nowadays. However, a reduction step of Se(VI) to Se(IV) is necessary as the hydride-forming species is HSeO(3)(-) (oxydation state+IV). This paper describes the development of a batch assisted microwave system allowing a rapid (<5 min) conversion of Se(VI) to Se(IV). Hydride generation is performed by a flow injection system and detection by ICP/MS. Detection limits of 6 and 8 pg for Se(IV) and for Se(VI) (by using a sample loop of 200 mul) respectively have been achieved. This method has been validated by participating in a European certification exercise for inorganic Se speciation in aqueous solutions.     

Reductive immobilization of <Superscript>79</Superscript>Se by iron canister under simulated repository environment

To understand the fate of ⁷⁹Se in a repository-like environment, the interactions between iron canister surface with dissolved selenite (SeO₃ ²⁻) and selenate (SeO₄ ²⁻) in anaerobic solutions have been investigated. Se(IV) immobilization on iron surface was observed to be about 100 times faster than that of Se(VI) at same conditions. An iron surface coated with a FeCO₃ layer corrosion product is more reactive than a polished iron to immobilize Se(IV) and Se(VI). The reacted iron surfaces were analysed by scanning electron microscopy (SEM) and energy dispersive spectrometer (EDS), X-ray diffraction (XRD), Raman spectrometry and micro-X-ray Absorption Spectroscopy (XAS). The result show that Se(IV) and Se(VI) were reduced and precipitated. The dominating phase was found to be FeSe_2.     

AE-HG-AFS测定长期汞暴露人群补硒后尿中硒的形态

建立了一种利用阴离子交换高效液相色谱与氢化物发生原子荧光光谱联用同时测定四、六价硒及硒代半胱氨酸(SeCys)形态的方法。优化了六价硒的还原条件及仪器检测参数,以不同浓度的柠檬酸铵作为流动相,在10 min内同时分离了四、六价硒及硒代半胱氨酸(SeCys)。采用加标法定量,加标回收率在90%～119%之间,相对标准偏差为1.6%～3.1%(100μg/L),四、六价硒及硒代半胱氨酸(SeCys)的检出限分别为0.32μg/L、0.47μg/L和0.44μg/L(进样量为100μL)。应用该法对长期汞暴露人群补硒后尿中的小分子硒的形态进行了分析,仅检测到硒代半胱氨酸(SeCys)。     

Sequential collection of selenium(IV) and selenium(VI) by the use of an anion-exchange resin loaded with bismuthiol-II sulphonic acid

A new ligand-loaded anion-exchange resin has been developed which allows determination of Se(VI) and Se(IV) in mixtures of the two. The ligand is a sulphonic acid derivative of bismuthiol-II.     

Speciation of selenium(IV) and selenium(VI) in environmental samples by the combination of graphite furnace atomic absorption spectrometric determination and solid phase extraction on Diaion HP-2MG

A simple solid phase extraction procedure for speciation of selenium(IV) and selenium(VI) in environmental samples has been proposed prior to graphite furnace atomic absorption spectrometry. The method is based on the solid phase extraction of the selenium(IV)-ammonium pyrrolidine dithiocarbamate (APDC) chelate on the Diaion HP-2MG. After reduction of Se(VI) by heating the samples in the microwave oven with 4 mol l⁻¹ HCl, the system was applied to the total selenium. Se(VI) was calculated as the difference between the total selenium content and Se(IV) content. The experimental parameters, pH, amounts of reagents, eluent type and sample volume were optimized. The recoveries of analytes were found greater than 95%. No appreciable matrix effects were observed. The adsorption capacity of sorbent was 5.20 mg g⁻¹ Se (IV). The detection limit of Se (IV) (3sigma, n = 11) is 0.010 μg l⁻¹. The preconcentration factor for the presented system was 100. The proposed method was applied to the speciation of selenium(IV), selenium(VI) and determination of total selenium in natural waters and microwave digested soil, garlic, onion, rice, wheat and hazelnut samples harvested various locations in Turkey with satisfactory results. In order to verify the accuracy of the method, certified reference materials (NIST SRM 2711 Montana Soil, NIST SRM 1568a Rice Flour and NIST SRM 8418 Wheat Gluten) were analyzed and the results obtained were in good agreement with the certified values. The relative errors and relative standard deviations were below 6 and 10%, respectively.     

Optimization of the reduction of Se(VI) to Se(IV) in a microwave oven

 Parameters for the reduction of Se(VI) to Se(IV) in HCl medium by heating in a microwave oven have been optimized. The reduction resulted to be quantitative applying 100% power, corresponding to 600 W heating for 2 min in 6 mol/L or for 3 min in 4 mol/L HCl. The behavior of selenomethionine and selenocystine under the optimized reduction conditions was studied in order to evaluate a possible interference of these selenium species in the determination of Se(VI). The final determination of Se(IV), and Se(VI) were done by hydride generation-atomic absorption spectrometry. The analytical merits of the method are reported. The method was applied to the selective determination of Se(IV), and Se(VI) in spiked river and lake water. Received: 6 December 1996/Revised: 1 April 1997/Accepted: 3 April 1997