Morphology and mechanical properties of reconstituted wood board waste-polyethylene composites

The morphology and mechanical properties of reconstituted wood board waste-polyethylene composites were studied using virgin polyethylene (PE) and 2 wt% maleic anhydride (MA) modified polyethylene (MAPE) as matrices. Although the wood waste (WW) and PE are not compatible with each other, dynamic mechanical analyses (DMA) show considerable shifting in the α-transition temperature and crystallisation temperature (T _c) of PE in the unmodified composites, indicating physical interaction between PE and WW. The increase in crystallinity with increasing WW content up to 50 wt% indicates that WW is a potential nucleating agent for PE. However, the tensile strength of the unmodified composites gradually decreases with WW content, indicating that the improvement in interface adhesion is essential for WW to be used as reinforcing fillers. Fourier transform infrared spectroscopic (FTIR) results indicate that MAPE interacts with WW through esterification and hydrogen bonding to form good adhesion between the two phases. Inward shifting in glass transition temperature (T _g) for the MAPE-based composites containing less than 60 wt% WW indicates that WW and MAPE are partially compatible with each other. SEM micrographs of MAPE-based composites provide further evidence for this mechanism. The tensile strength of the MAPE-based composites is clearly higher than that of the virgin PE-based composites.     

Natural fibre composites from polyethylene waste and hazelnut shell: dimensional stability,physical, mechanical and thermal properties

Within the framework of this study, the physical modification of high-density polyethylene waste foil was performed using finely ground hazelnut flour to produce a composite whose physical, mechanical and flammable properties make it possible to use inside and outside of buildings. Three mixtures were produced with filler shares of 11, 26 and 42 vol.% using equipment that is normally used in polymer processing, and no refining additives were applied. The produced materials were analysed for their processing (mass flow ratio), physical (density and moisture content) and mechanical properties (tensile strength, elongation at break and dynamic thermal analysis) and resistance to environmental factors (swelling and water absorption, thermogravimetric analysis and combustion heat). The particle size distribution of the filler and morphological properties of the composites (scanning electron microscopy) were also investigated. It was vital to obtain an inexpensive material with low absorptivity. The resulting materials are characterised by a low density, acceptable low absorptive and good mechanical properties; also, they can constitute an important fuel once their practical properties have been exploited.     

Effect of silane/nano-silica on the mechanical properties of basalt fiber reinforced epoxy composites

The present study explains the role of surface modification of constituent materials on composite material performance. The influence of silane and nano-hybrid coatings on mechanical properties of basalt fibers and composite materials on their base was investigated. Infrared spectroscopy indicated that modification of basalt fiber surface and nano-SiO₂ was successfully applied. The surface modification leads to the significant increase in the tensile strength of basalt fibers compared to the non-coated fibers. The tensile strength of silane-treated fibers was established 23% higher than the non-coated fibers, indicating that silane plays a critical role in the strength retention of basalt fibers. Also it was pointed out that silane coupling agents can be used for the preparation of the nano-hybrid coating. Addition of SiO₂ nanoparticles into the fiber surface was incorporated to enhance the interfacial bonding of basalt fiber reinforced epoxy composite.     

Improvement of the mechanical and rheological properties of HDPE/PET/MWCNT nanocomposites

High density polyethylene (HDPE)/poly (ethylene terephthalate) (PET) (90/10 wt.%) blends and HDPE/PET/multi-walled carbon nanotubes (MWCNTs) nanocomposites were prepared by melt mixing process, and the influence of MWCNTs on the mechanical and rheological properties of the nanocomposites was investigated. MWCNTs were added up to 5 wt.% in the HDPE/PET matrix. Transmission electron microscopy images reveal that the MWCNTs were homogeneously dispersed in the HDPE/PET matrix. Improvement of mechanical properties was observed by the addition of MWCNTs compared with HDPE/PET blends. Prominent increases in the complex viscosity and storage modulus of the nanocomposites were found with increasing MWCNT content.     

Effects of particle/matrix interface and strengthening mechanisms on the mechanical properties of metal matrix composites

A randomly distributed multi-particle model considering the effects of particle/matrix interface and strengthening mechanisms introduced by the particles has been constructed. Particle shape, distribution, volume fraction and the particles/matrix interface due to the factors including element diffusion were considered in the model. The effects of strengthening mechanisms, caused by the introduction of particles on the mechanical properties of the composites, including grain refinement strengthening, dislocation strengthening and Orowan strengthening, are incorporated. In the model, the particles are assumed to have spheroidal shape, with uniform distribution of the centre, long axis length and inclination angle. The axis ratio follows a right half-normal distribution. Using Monte Carlo method, the location and shape parameters of the spheroids are randomly selected. The particle volume fraction is calculated using the area ratio of the spheroids. Then, the effects of particle/matrix interface and strengthening mechanism on the distribution of Mises stress and equivalent strain and the flow behaviour for the composites are discussed.     

Morphology, mechanical, cross-linking, thermal, and tribological properties of nitrile and hydrogenated nitrile rubber/multi-walled carbon nanotubes composites prepared by melt compounding: The effect of acrylonitrile content and hydrogenation

The purpose of this work was to prepare nanocomposites by mixing multi-walled carbon nanotubes (MWCNT) with nitrile and hydrogenated nitrile elastomers (NBR and HNBR). Utilization of transmission electronic microscopy (TEM), scanning electron microscopy (SEM), and small- and wide-angle X-ray scattering techniques (SAXS and WAXS) for advanced morphology observation of conducting filler-reinforced nitrile and hydrogenated nitrile rubber composites is reported. Principal results were increases in hardness (maximally 97 Shore, type A), elastic modulus (maximally 981 MPa), tensile strength (maximally 27.7 MPa), elongation at break (maximally 216%), cross-link density (maximally 7.94 × 10²⁸ m⁻³), density (maximally 1.16 g cm⁻³), and tear strength (11.2 kN m⁻¹), which were clearly visible at particular acrylonitrile contents both for unhydrogenated and hydrogenated polymers due to enhanced distribution of carbon nanotubes (CNT) and their aggregated particles in the applied rubber matrix. Conclusion was that multi-walled carbon nanotubes improved the performance of nitrile and hydrogenated nitrile rubber nanocomposites prepared by melt compounding.     

Morphology,conductivity, and mechanical properties of polypyrrole-containing composites

An electrical-conducting polypropylene/polypyrrole (PP/PPy) composite was prepared by the chemically oxidative modification reaction of pyrrole on the surface of PP particles in suspension. Another type of PP/PPy composite was prepared by mixing the coated PP particles with noncoated PP particles at room temperature. The composites were processed by compression molding or by injection molding. The injection-molded composites exhibited better mechanical properties compared to compression-molded samples, while these composites showed better antistatic behavior and electrical conductivity. The differences in the behavior of the two types of composites were caused by the different structure of the PPy phase, which was studied by hot-stage optical microscopy and X-ray photoelectron spectroscopy (XPS).     

Optimizing mechanical and thermal expansion properties of carbon/carbon composites by controlling textures

The present study explored the effect of medium texture (MT) content on flexural properties and thermal expansion coefficients (CTE_S) of carbon/carbon (C/C) composites with multilayered pyrolytic carbon. The specimen with 39% MT exhibited maximum flexural strength of 221.55 MPa, increasing by 52% compared with pure high texture. While the flexural strength decreased when the MT content exceeded 39%. The excellent strength can be attributed to crack deflection between multilayered texture and the strong interface bonding between fibers and matrix. Moreover, the four specimens expressed a similar trend of CTE_S in the direction of XY and Z. In the direction of XY, the specimen with 39% MT had the lowest CTE_S from 800 °C to 2100 °C. Therefore, the C/C composites with 39% MT have the best mechanical and thermal expansion properties, which means that the properties of C/C composites can be optimized by controlling the texture.     

Effect of surface treatment of nanoclay on the mechanical properties of epoxy/glass fiber/clay nanocomposites

A new method of silane treatment of nanoclays is reported where in the clay is nanodispersed in hydrolyzed silanes. The surface functionalization of Cloisite^® 15A nanoclay has been carried out using two different silane coupling agents: 3-aminopropyltriethoxy silane and 3-glycidyloxypropyltrimethoxy silane using varied amounts of silane coupling agents, e.g. 10, 50, 200, and 400 wt% of clay. The surface modification of Cloisite^® 15A has been confirmed by Fourier transform infrared spectroscopy. The modified clays were then dispersed in epoxy resin, and glass fiber-reinforced epoxy clay laminates were manufactured using vacuum bagging technique. The fiber-reinforced epoxy clay nanocomposites containing silane modified clays have been characterized using small angle X-ray scattering, transmission electron spectroscopy and differential scanning calorimetry. The results indicate that the silane treatment of nanoclay aided the exfoliation of nanoclay and also led to an increase in mechanical properties. The optimized amount of silane coupling agents was 200 wt%. The nanocomposites containing clay modified in 200 wt% of silanes exhibited an exfoliated morphology, improved tensile strength, flexural modulus, and flexural strength. The improved interfacial bonding between silane modified nanoclays and epoxy matrix was also evident from significant increase in elongation at break.     

Prediction of thermal conductivity of polymer-based composites by using support vector regression

Support vector regression (SVR) combined with particle swarm optimization (PSO) for its parameter optimization, was proposed to establish a model to predict the thermal conductivity of polymer-based composites under different mass fractions of fillers (mass fraction of polyethylene (PE) and mass fraction of polystyrene (PS)). The prediction performance of SVR was compared with those of other two theoretical models of spherical packing and flake packing. The result demonstrated that the estimated errors by l...     

Effect of monomer-treated inorganic fillers on mechanical,rheological, and thermal properties of LLDPE nanocomposites

This article discusses the role of nanoscale calcium carbonate (nCC) surface treatment in affecting the mechanical, rheological, and thermal properties of linear low-density polyethylene (LLDPE). The mechanical tests indicated that nCC could simultaneously reinforce and toughen LLDPE. In addition, the composite sample with methacrylic acid (MA)-treated nanoparticles shows further increased mechanical properties as compared to unmodified nanoparticles. In the presence of dicumyl peroxide (DCP), a small amount of MA could increase markedly the mechanical properties of LLDPE/nCC composites. The results of rheological property analysis indicated that the viscosity increased with increasing amount of the filler, especially at low shear rates, but showed a substantial reduction with increasing concentration of the reactive monomer. The thermal behavior of these materials is evaluated by differential scanning calorimetry and thermogravimetric analysis. The addition of a small amount of MA and DCP enhances the stabilization of the blends.     

Morphology,miscibility and mechanical properties of PMMA/PC blends

This study deals with some results on morphology, miscibility and mechanical properties for polymethyl methacrylate/polycarbonate (PMMA/PC) polymer blends prepared by solution casting method at different concentration between 0 and 100 wt%. Dynamic storage modulus and tan δ were measured in a temperature range from 30 to 180°C using dynamical mechanical analyzer (DMA). The value of the storage modulus was found to increase with the addition of the PC in the matrix. Transition temperature of pure PMMA and pure PC is found to be 83.8 and 150°C, respectively. The result shows that the two polymers are miscible for whole concentration of PC in PMMA. The distribution of the phases in the blends was studied through scanning electron microscopy (SEM). Also the mechanical properties like elongation at break and fracture energy of the PMMA/PC blends increase with the increase in concentration of PC in PMMA.     

Comparative experimental studies on the mechanical and degradation properties of natural fibers reinforced polypropylene composites

Coir/silk fiber-reinforced polypropylene (PP) based unidirectional composites (40 wt.%) were manufactured by compression molding. Coir/silk fibers and PP sheets were treated with ultraviolet radiation at different intensities and then composites were fabricated. It was found that mechanical properties of irradiated silk/irradiated PP composites were found to increase significantly compared to the untreated ones and even higher than that of irradiated coir/irradiated PP composites. Soil degradation tests indicated that irradiated coir/irradiated PP composites significantly lost much of its mechanical properties, but irradiated silk/irradiated PP composites retained their strength of its original integrity. Scanning electron microscopy and water uptake of both types of composites were also investigated.     

Anisotropy of mechanical and thermal properties of perovskite LaYbO3: first-principles calculations

LaYbO₃ ceramic material with a perovskite structure has the advantages of a high melting point, sintering resistance and high-temperature phase stability. It is a promising candidate for a structurally and functionally integrated material. However, the anisotropy of physical properties of LaYbO₃ has rarely been studied. Herein, the anisotropy of the mechanical and thermal properties of LaYbO₃ was studied by first-principles calculations. The elastic coefficients, Young’s modulus, Poisson’s ratio and minimum thermal conductivity of LaYbO₃ were found to exhibit anisotropic characteristics. In particular, the sound velocity of the longitudinal wave was nearly twice that of the transverse wave. Especially, the minimum thermal conductivity of LaYbO₃ at high temperature was found to be as low as 0.88?W/m?K, indicating that the compound has potential for use in thermal insulation applications.     

Influence of functionalization on mechanical and electrical properties of carbon nanotube-based silver composites

In this study, we have extended the molecular-level mixing method to fabricate multiwall carbon nanotube (CNT)-reinforced silver nanocomposites. The multiwall nanotubes used in the synthesis process were dispersed by two ways viz. covalent and non-covalent functionalization techniques. To elucidate the comparative effects of functionalization, structural, mechanical and electrical properties of nanocomposites were evaluated before and after sintering. The structural characterization revealed that the nanotubes were embedded, anchored and homogenously dispersed within the silver matrix. Hardness and Young’s modulus of nanotube-reinforced nanocomposite were increased by a factor of 1–1.6 times than that of pure silver, even before and after the sintering. Covalently functionalized nanotube-based composites have shown more enhanced mechanical properties. The CNT reinforcement also improved the electrical conductivity of low-conducting nanosilver matrix before sintering. Non-covalently functionalized nanotube-based nanosilver composites showed more increased electrical conductivity before sintering. But a negative reinforcement effect was observed in high-conducting bulk silver matrix after the sintering. Thus, covalent functionalization might be appropriate for mechanical improvement in low-strength materials. However, non-covalent functionalization is suitable for electrical enhancement in low-conducting nanomaterials.     

The influence of SiCp oxidized on the interface layer and thermal conductivity of SiCp/Al composites

In this work, oxidation of silicon carbide particles (SiCp) at elevated temperature and its influence on the interface layer and thermal conductivity of SiCp/ZL101 composites prepared using pressure infiltration process were investigated respectively. It is found that initial temperature for the oxidation of SiCp is about 850?°C, and that the oxidation increment of SiCp and the thickness of SiO₂ layer increase with the increase in pre-oxidation temperature and time, when the oxidized temperature exceeds 1100?°C, or the duration time exceeds 2?h at 1100?°C, a small amount of ablation will take place on the SiCp, as well as the oxidized layer has some loss. The formation of SiO₂ layer can provide certain interface reactions with interface layers (3.1–6.36?μm), and the higher the thickness of SiO₂ layer, the thicker the interface layer in SiCp/Al composites. However, the thickness of SiO₂ layer is more than 5.9?μm, which is not benefit for the formation of interface layer. With the increase in the thickness of interface layer, thermal conductivity declines, but is not linear.     

Factors affecting the microstructure and mechanical properties of Ti-Al3Ti core-shell-structured particle-reinforced Al matrix composites

This work studied the effects of matrix powder and sintering temperature on the microstructure and mechanical properties of in situ formed Ti–Al₃Ti core–shell-structured particle-reinforced pure Al-based composites. It has been shown that both factors have significant effects on the morphology of the reinforcements and densification behaviour of the composites. Due to the strong interfacial bonding and the limitation of the crack propagation in the intermetallic shell during deformation by soft Al matrix and Ti core, the composite fabricated using fine spherical-shaped Al powder and sintered at 570 °C for 5 h has the optimal combination of the overall mechanical properties. The study provides a direction for the optimum combination of high strength and ductility of the composites by adjusting the fabrication parameters.     

First-principles study of structural,mechanical, lattice dynamical and thermal properties of nodal-line semimetals ZrXY (X=Si,Ge; Y=S,Se)

Abstract

The nodal-line semimetals are new and very promising materials for technological applications. To understand their structural, mechanical, lattice dynamical and thermal properties in detail, we have investigated theoretical study of ZrXY (X = Si,Ge; Y = S,Se) using Density Functional Theory for the first time. Obtained lattice parameters are in excellent agreement with previous experimental data. These nodal-line semimetals obey the mechanical stability conditions for tetragonal structure. We obtain Bulk modulus, Shear modulus, Poisson’s ratio, Pugh ratio, sound velocities and thermal conductivity using elastic constant. All the materials behave in brittle manner. Poisson’s ratio data and Bader charge analysis results indicate that the ionic bonding characters are dominant. Next, the lattice dynamical properties are calculated. Phonon density of states shows that nodal-line semimetals ZrXY are also dynamically stable in the tetragonal structure. Raman and IR active phonon modes are determined. Highest optical mode at gamma point corresponds to A_2u (IR active) and E_g (Raman active) modes for ZrXSe and ZrXS, respectively. Based on phonon density of states, thermal properties such as Helmholtz free energy, entropy, heat capacity at constant volume and Debye temperature are also presented and discussed.     

Metal-Filled Epoxy Composites: Mechanical Properties and Electrical/Thermal Conductivity

Abstract

The mechanical properties and the electrical and thermal conductivity of composites based on an epoxy polymer (EP) filled with dispersed copper (Cu) and nickel (Ni) were studied. It was shown that the electrical conductivity of the composites demonstrated percolation behavior with the values of the percolation threshold being 9.9 and 4.0?vol.% for the EP-Cu and EP-Ni composites, respectively. Using the Lichtenecker model, the thermal conductivity of the dispersed metal phase in the composites, λ_f, was estimated as being 35?W/mK for Cu powder and 13?W/mK for Ni powder. It was shown that introduction of the filler in EP led to a decrease in the intensity of the mechanical loss tangent (tan δ) peak that was caused by the existence of an immobilized polymer layer around the filler particles which did not contribute to mechanical losses. Using several models the thickness of this layer, ΔR, was estimated. The concept of an “excluded volume” of the polymer, V_ex, i.e. the volume of the immobilized polymer layer, which does not depend on the particle size and is determined solely by the value of the interaction parameter, B, was proposed.     

Thermal and Spectral Dielectric Properties of Polypyrrole/Polymethylmethacrylate Composites

Thermal properties of polypyrrole/polymethylmethacrylate (PPy/PMMA) composites were analyzed by thermal gravimetric analysis (TGA) and differential scanning calorimetry (DSC). A decrease in the glass transition temperatures with PPy concentration reveals the increase of segmental motion. The dielectric properties of these composites were studied for several weight concentrations of PPy in the frequency range between 500 Hz and 0.2 MHz, over the temperature range 23–110°C. Jonscher's phenomenological model has been used for modeling the dielectric response of the composite materials. This study shows that the results obtained for the dielectric response are in good agreement with the results of TGA and DSC measurements.