Structural,thermal and electrical properties of polyvinyl alcohol/poly(vinyl pyrrolidone)–sodium nitrate solid polymer blend electrolyte

Sodium ion conducting solid polymer blend electrolyte thin films have been prepared by using polyvinyl alcohol (PVA)/poly(vinyl pyrrolidone) (PVP) with NaNO₃ by solution cast technique. The prepared films were characterized by various methods. The complexation of the salt with the polymer blend was identified by X-ray diffraction (XRD) and Fourier transforms infrared spectroscopy (FTIR), Differential scanning calorimetry was used to analyze the thermal behavior of the samples, and the glass transition temperature is low for the highest conducting polymer material. The scanning electron microscopy gives the surface morphology of the polymer electrolytes. The frequency and temperature dependent of electrical conductivities of the films were studied using impedance analyzer in the frequency range of 1 Hz to 1 MHz. The highest electrical conductivity of 50PVA/50PVP/2 wt% NaNO₃ concentration has been found to be 1.25 × 10^?5 S cm^?1 at room temperature. The electrical permittivity of the polymer films have been studied for various temperatures. The transference number measurements showed that the charge transport is mainly due to ions than electrons. Using this highest conducting polymer electrolyte, an electrochemical cell is fabricated and the parameters of the cells are tabulated.     

Effect of silica type and concentrations on the physical properties of EPDM cured by γ -irradiation

This paper reports the results of studies on the thermal and electrical properties of gamma radiation cured composites based on ethylene propylene dieyne rubber (EPDM) reinforced with different concentrations of micro- and nano-silica. The effect of gamma irradiation in the presence of ethylene glycol dimethacrylate (EGDM) as radiation sensitizer on melt flow properties of EPDM was also studied. Thermogravimetric studies of the composites show that the degradation of vulcanizates is controlled mainly by the silica type and its concentration. Increasing the amount of micro- or nano-silica in the vulcanizate decreases the maximum rate of decomposition of the major degradation step compared with that of the unfilled-cured one. The micro- and nano-composites exhibited remarkable heat resistance properties compared with that of the pure EPDM as the filler dispersion of silica inhibited the thermal degradation of the polymeric matrix, which led to the micro and nano-composites showing great improvement in thermal stability. A considerable change in decomposition rate is observed by increasing filler loading from 10 to 39 phr. The dielectric properties of such composites are affected by the silica type and concentration. The dielectric constant and ac-conductivity for all composites were found to increase with increasing silica loading, which is mainly due to the interfacial polarization. The ac-conductivity values of silica/EPDM composites exhibit a strong frequency dependence with both fillers used. The conductance and dielectric constant values have been fitted using a conduction model for all samples.     

Effect of irradiation and pre-ageing temperature on the mechanical properties of Al–Si alloy

Al–1wt.%Si alloy samples in the solid solution state were irradiated with doses of gamma rays up to 1.75 MGy for 2 h in the temperature range from 423 to 553 K. Induced variations in structure, mechanical and electrical properties were traced by suitable techniques. Observed changes in the measured parameters, internal friction Q ^?1, thermal diffusivity D _th, dynamic elastic modulus Y and resistivity, ρ, were explained in terms of the role and mode of interaction of lattice defects in irradiated and thermally treated samples. Composition inhomogeneity and variations in mass distribution in the matrix were also considered. The structure identification of the samples was carried out by using conventional X-ray diffraction techniques and transmission electron microscopy micrographs.     

Effect of the phonon and magnetic anharmonicity on the thermal and elastic properties of nearly magnetic δ-plutonium

The temperature dependences of the total heat capacity and the lattice components of the bulk modulus, the volume thermal expansion coefficient, and the mean-square deviation of atoms from the equilibrium positions of nearly magnetic δ-plutonium (using the Pu_0.96Ga_0.04 alloy as an example) have been calculated within the framework of the self-consistent thermodynamic model. The electronic heat capacity has been calculated using the results obtained in terms of the self-consistent spin-fluctuation theory based on the inclusion of the strong magnetic anharmonicity, which leads to a splitting of the electronic spectra by fluctuating exchange fields. On this basis, the effect of phonon anharmonicity not only on the lattice heat capacity but also on other thermal and elastic properties has been considered.     

Effect of SnI2 on the thermal and optical properties of Ge–Se–Te glasses

A systematic series of (Ge₂₀Se₁₅Te₆₅)_1?x–(SnI₂)_x (x = 0, 0.05, 0.1, 0.15) chalcogenide glasses have been prepared. The amorphous nature can be confirmed by XRD and SEM. With the SnI₂ content increasing, the indirect optical band gaps are decreased from 0.662 to 0.622 eV according to Tauc laws. The introduction of SnI₂ makes the glasses much easier to prepare and more stable against crystallization, making them drawable as optical fibers. The highest ΔT (130 °C) value for (Ge₂₀Se₁₅Te₆₅)_0.9–(SnI₂)_0.1 glass composition can be obtained. A slight red-shifting of the long-wavelength cutting-off edge from 18.4 to 19.4 μm was shown and it seems that SnI₂ in these glasses offers the improvement in the far-infrared properties.     

Effect of gamma irradiation on the structural,thermal and optical properties of Makrofol BL 2–4

Makrofol BL 2–4 is an extrusion film based on Makrolon polycarbonate. It comprises excellent die-cutting performance combined with high light transmission and moderate light scattering properties. It is a class of polymeric solid state nuclear track detectors which has many applications in various radiation detection fields. In the present work, Makrofol samples were irradiated using different gamma doses ranging from 10 to 350 kGy. The structural modifications in the gamma-irradiated Makrofol samples have been studied as a function of dose using different characterization techniques such as X-ray diffraction, intrinsic viscosity, Fourier transform infrared spectroscopy, thermogravimetric analysis, refractive index and color difference studies. The gamma irradiation in the dose range 20–200 kGy led to a more compact structure of Makrofol polymer, which resulted in an improvement in its thermal stability with an enhancement in its structural and optical properties.     

Fabrication and properties of silicene and silicene–graphene layered structures on Ir(111)

Silicene, a two-dimensional(2D) honeycomb structure similar to graphene, has been successfully fabricated on various substrates. This work will mainly review the syntheses and the corresponding prope√rties o√f silicene and√ silice√ne–graphene layered structures on Ir(111) substrates. For silicene on Ir(111), the buckled(3 ×3) silicene/(7 ×7)Ir(111) configuration and its electronic structure are fully discussed. For silicene–graphene layered structures, silicene layer can be constructed underneath graphene layer by an intercalation method. These results indicate the possibility of integrating silicene with graphene and may link up with potential applications in nanoelectronics and related areas.     

Effect of Pt on interdiffusion and mechanical properties of the γ and γ′ phases in the Ni–Pt–Al system

The effect of Pt on the growth kinetics of the γ′-[Ni(Pt)]₃Al ordered intermetallic phase and the γ-Ni(Pt, Al) solid solution diffusion rates of the species, hardness and elastic modulus was examined by employing the diffusion couple experimental technique. Experiments were conducted by using the β-Ni(Pt)Al phase and Ni(Pt) alloy couples, each of which had a fixed amount of Pt (5, 10 and 15 at. %) in both the end members so that the Pt content is more or less constant throughout the interdiffusion zone. The results suggest that the growth kinetics of both phases and the average effective interdiffusion coefficients of Ni and Al increase with the increase in Pt content. Nanoindentation studies across the compositional gradients show that the mechanical properties of the intermetallic phase in the superalloy are relatively insensitive to the presence of Pt but are more sensitive to the Ni/Al ratio. In contrast, the marked variation in the hardness of the γ phase were noted, increasing markedly with Al concentration in a given couple and also increasing with increasing Pt content. Possible causes for the observed variations are discussed.     

Effect of the donor–acceptor properties of ligands on the spectroscopic and electrochemical properties of mixed-ligand complexes of Pt(II) and Ir(III) with cyclometalated 2-phenylbenzothiazole

The results of the spectroscopic NMR (¹H, ¹³C, and ¹⁹⁵Pt), infrared, optical, and voltammetric characteristics of the mixed-ligand complexes of Pt(II) and Ir(III) with metalated 2-phenylbenzothiazole and tert-butylisocyanide (tBuNC), acetonitrile (AN), ethylenediamine (En), O-ethyldithiocarbamate (Exn^–), and diethyldithiocarbamate (Dtc–) ions are presented. It is demonstrated that the change in donor–acceptor interaction of ligands tBuNC, AN, En, Exn^–, and Dtc^– with metal leads to an increase in the energy of the highest occupied molecular orbital of the complexes and is accompanied by a shift of the cathode potential of the metal-centered oxidation, a bathochromic shift of the spin-allowed and spin-forbidden metal-tocyclometalated ligand optical charge transfer transitions, and an increase the degree of mixing of the ¹MLCT and triplet intraligand states, responsible for the phosphorescence of the complexes.     

Effect of thermal environment on quantum nonlocality of superposition of two coherent states (π/2 out of phase)

Recently we studied the tests of Bell-type inequalities with superposition of two coherent states (π/2 out of phase) [D. K. Mishra, Acta Phys. Pol. A. 123, 21 (2013)]. Here, we study the effect of thermal environment on the Bell-CHSH inequality. As the state interacts with the thermal environment, the time evolution of the linear entropy to study the purity loss in the state has also been examined.     

Effect of Sn and Al additions on the microstructure and mechanical properties of amorphous Ti–Cu–Zr–Ni alloys

Amorphous Ti–Cu–Zr–Ni alloys with minor addition of Sn and Al were prepared by melt spinning technique.The effects of Sn and Al additions on the microstructures and mechanical properties of glassy ribbons were investigated.The amorphous state of ribbons was confirmed by x-ray diffraction and transmission electron microscopy,where those ribbons with Sn addition exhibited a fully amorphous state.The characteristic temperature indicates that Ti_(45)Cu_(35)Zr_(10)Ni_5Sn_5 alloy has a stronger glass-forming ability,as proven by differential scanning calorimetry.Ti_(45)Cu_(35)Zr_(10)Ni_5Al_5 alloy showed a better hardness of 9.23 GPa and elastic modulus of 127.15 GPa and good wear resistance.Ti_(45)Cu_(35)Zr_(10)Ni_5Sn_5 alloy displayed a pop-in event related to discrete plasticity according to nanoindentation.When the temperature is below 560 K,Ti_(45)Cu_(35)Zr_(10)Ni_5Sn_5 alloy mainly exhibits elasticity.When the temperature rises between 717 K and 743 K,it shows a significant increase in elasticity but decrease in viscoelasticity after the ribbon experiences the main relaxation at 717 K.When the temperature is above 743 K,the ribbon shows viscoplasticity.     

Effect of the amounts of glycidyl methacrylate on the mechanical and dynamic properties of styrene–butadiene–glycidyl methacrylate terpolymer/silica composites

GMA-SBRs with GMA contents in the range of 0.06–0.71 wt.% were synthesized and used to evaluate the properties of the silica composites for fuel-efficient tires. The chemical structures of the GMA-SBRs were analyzed using Fourier transform infrared spectroscopy, ¹H nuclear magnetic resonance (¹H NMR), size exclusion chromatography (SEC), and differential scanning calorimetry (DSC). GMA-SBRs can enhance filler–rubber interaction through covalent bond formation between the silica filler and rubber molecules. After compounding, the cure characteristics and mechanical and dynamic properties of the GMA-SBR silica-filled composites were analyzed. The mechanical properties, including the Mooney viscosity, bound rubber, swelling ratio, and moduli, exhibited obvious differences with increasing GMA content. However, the optimum content of GMA in the GMA-SBR, in terms of dynamic properties such as the Payne effect which represents the change in dynamic modulus against the strain to determine the extent of filler flocculation and tan δ at 60 °C representing tire rolling resistance, was ~0.6 wt.%. These results are due to improved silica dispersion, resulting from increased covalent bond formation between GMA-SBR and the silica surface. This approach assists in the determination of functional group contents in functionalized emulsion styrene–butadiene rubber for fuel-efficient tires, leading to a decrease in vehicular greenhouse gas emission.     

Effect of MAPP and TMPTA as compatibilizer on the mechanical properties of cellulose and oil palm fiber empty fruit bunch–polypropylene biocomposites

The effect of compatibilizers, namely, maleic anhydride grafted polypropylene (MAPP GR-205) and trimethylolpropane triacrylate (TMPTA), on the mechanical and morphological properties of the PP-cellulose (derived from oil palm empty fruit bunch fiber) and PP-oil palm empty fruit bunch fiber (EFBF) biocomposites has been studied. The ratio of PP : cellulose and PP : EFBF is fixed to 70 : 30 (wt/wt%) while the concentration of the compatibilizer is varied from 2.0 to 7.0 wt%. Results reveal that at 2.0 wt% of MAPP concentration, tensile strength of PP-EFBF biocomposite is significantly improved. This is due to the enhanced EFBF matrix adhesion resulting in an improvement in EFBF biocomposite performance. There are no significant changes observed in the PP-cellulose biocomposite properties upon the addition of MAPP. In contrast to the tensile strength, flexural modulus and impact strength are significantly improved with the addition of 2.0 wt% TMPTA to PP-cellulose biocomposite. The enhancement of mechanical properties in the presence of TMPTA is believed to be attributed to crosslinking of multifunctional monomer with the hydroxyl groups of cellulose.     

Effect of sputtered Cu film’s diffusion barrier on the growth and field emission properties of carbon nanotubes by chemical vapor deposition

Growth of carbon nanotube (CNT) films with good field emission properties on glass is very important for low cost field emission display (FED) applications. In addition to Ni, Co and Fe, Cu can be a good catalyst for CNT growth on glass, but due to diffusion into SiO₂ it is difficult to control the CNTs density and uniformity. In this paper, four metal barrier layers (W, Ni, Cr, Ti) were deposited by dc magnetron sputtering on glass to reduce the Cu diffusion. As-grown CNT films showed various morphologies with the use of different barrier metals. CNTs with uniform distribution and better crystallinity can be synthesized only on Ti/Cu and W/Cu. Voltage current measurements indicate that better field emission properties of CNT films can be obtained on titanium and tungsten barriered Cu, while chromium and nickel are not suitable barrier candidates for copper in CNT-FED applications because of the reduced emission performance. PACS 81.05.Uw; 61.46.Fg; 85.45.Db; 66.30.-h     

Effect of lithium thiocyanate addition on the structural and electrical properties of biodegradable poly(ε-caprolactone) polymer films

Polymer electrolyte films of biodegradable poly(ε-caprolactone) (PCL) doped with LiSCN salt in different weight ratios were prepared using solution cast technique. The effect of crystallinity and interaction between lithium ions and carbonyl groups of PCL on the ionic conduction of PCL:LiSCN polymer electrolytes was characterized by X-ray diffraction (XRD), optical microscopy, Fourier transform infrared spectroscopy (FTIR) and AC impedance analysis. The XRD results revealed that the crystallinity of the PCL polymer matrix decreased with an increase in LiSCN salt concentration. The complexation of the salt with the polymer and the interaction of lithium ions with carbonyl groups of PCL were confirmed by FTIR. The ionic conductivity was found to increase with increasing salt concentration until 15 wt% and then to decrease with further increasing salt concentration. In addition, the ionic conductivity of the polymer electrolyte films followed an Arrhenius relation and the activation energy for conduction decreased with increasing LiSCN concentration up to 15 wt%. UV–vis absorption spectra were used to evaluate the optical energy band gaps of the materials. The optical energy band gap shifted to lower energies with increasing LiSCN salt concentration.     

Commentary on ‘The scattering of α and β particles by matter and the structure of the atom’ by E. Rutherford (Philosophical Magazine 21 (1911) 669–688)

To mark the 100th anniversary of the publication of Lord Rutherford's paper in Philosophical Magazine on the nuclear model of the atom, we review his ground-breaking work and outline subsequent developments.     

Direct measurement of the growth mode of graphene on SiC(0001) and SiC(0001¯)

We have determined the growth mode of graphene on SiC(0001) and SiC(0001ˉ) using ultrathin, isotopically labeled Si(13)C "marker layers" grown epitaxially on the Si(12)C surfaces. Few-layer graphene overlayers were formed via thermal decomposition at elevated temperature. For both surface terminations (Si face and C face), we find that the (13)C is located mainly in the outermost graphene layers, indicating that, during decomposition, new graphene layers form underneath existing ones.     

Effect of copper concentration on atomic site occupation by Fe ions and magnetic properties of (PrDy)–(FeCo)–B alloys

The effect of small copper additions (to ～6 at %) on the distribution of iron ions in six crystallographic sites of the unit cell of the main magnetic phase (PrDy)₂(FeCo)₁₄B has been detected. An increase in the copper concentration leads to a decrease in the 8j₁ site occupation by iron ions. Independently of the presence of copper, the temperature dependences of the saturation magnetization of all samples have a minimum which can correspond to the presence of a low-temperature phase or a compensation point in grain boundary regions of the (PrDy)₂(FeCo)₁₄B main magnetic phase. The alloys under study are not additive sets of all phases in their composition, but behave as new materials with the mutual influence of phases on each other.     

Effect of composition and thermal treatment on the properties and microstructure of Co–SiO<Subscript>2</Subscript> films

The effect of various physical factors (chemical composition, temperature, and thermal treatment) on the macroscopic properties of Co–SiO₂ film composites produced by ion-plasma sputtering of mosaic targets has been investigated. The microstructure parameters have been estimated indirectly by analyzing the magnetization curves and the temperature dependence of magnetization. It has been concluded that the model of homogeneous noninteracting superparamagnetic particles of hexagonal Co is applicable for describing the magnetic properties of the film composites under study over a rather wide range of compositions.