保偏光子晶体光纤的近圆形模场分布特性

在光纤陀螺中,由于保偏光纤的性能易受环境的影响,制约了光纤陀螺稳定性和精度的进一步提高。保偏光子晶体光纤的研究为光纤陀螺解决环境适应性问题提供了新思路,针对保偏光子晶体光纤与传统光纤的模场匹配问题,采用有限元方法,对保偏光子晶体光纤的保偏性能和模场分布特性进行了分析与研究。通过分析不同空气孔尺寸对保偏光子晶体光纤性能的影响,得到其保偏性能与模场分布特性存在相互制约性。提出了一种改善保偏光子晶体光纤模场分布的方法,并通过仿真分析验证了这一方法的可行性,这为光纤陀螺用光子晶体光纤的发展提供了借鉴。     

光子晶体光纤陀螺技术及其首次空间试验

光子晶体光纤具有抗辐射、抗弯曲、抗磁场干扰和温度敏感性低等优势,是空间用光纤陀螺的理想选择.针对空间用光纤陀螺,提出了四层孔和双层孔陀螺用光子晶体光纤结构,突破了光子晶体光纤长距离拉制关键技术,批量制备了陀螺用长距离低损耗实芯光子晶体光纤与空芯光子晶体光纤,利用开发的光子晶体光纤周向散射、背向散射、温度、磁等性能测试设...     

一种三芯液晶光子晶体光纤的特性

针对三轴光纤陀螺共用光源问题,提出了一种新型的多芯液晶光子晶体光纤,该光纤具有三个呈等边三角形几何形状排列的液晶纤芯.利用有限元法对其功率分布、模场、有效折射率和色散特性进行了数值分析,结果表明,这种三芯液晶光子晶体光纤可将传输光完全等分为三束光,且具有平坦色散特性,在波长为1.45μm～1.75μm之间的色散变化小于2 ps·km-1·nm-1.此外,该光纤在大约150 nm的波长范围内显示出超平坦的色散,并且可以通过改变中心空气孔的直径来调整超平坦色散的波长范围.研究成果对液晶光子晶体光纤、三轴光纤陀螺和三相光纤电流互感器的等光分束器、1×3多芯光子晶体耦合器和平坦色散光纤的进一步发展具有重要意义.     

一种高精度光纤陀螺用光子晶体光纤设计

为了解决光子晶体光纤陀螺中高阶模致非互易性问题,设计了一种用于高精度光纤陀螺的单模保偏光子晶体光纤。为获得光纤结构参数最优区域,基于全矢量有限元方法开展了光子晶体光纤模场分布、双折射特性和限制损耗与三个重要结构参数(归一化频率、空气填充比、大孔直径)的依赖关系数值仿真分析。以传统熊猫型保偏光纤特性为参照,确定了光子晶体光纤结构参数最优区域。采用优化的光子晶体光纤绕制了1500 m环圈并装配于陀螺,对陀螺进行了相应测试。未采用温度补偿措施下,陀螺全温零偏稳定性优于0.008 (°)/h (100 s, 1σ),表明这种光子晶体光纤适用于高精度光纤陀螺。     

一种三芯液晶光子晶体光纤的特性（英文）

针对三轴光纤陀螺共用光源问题,提出了一种新型的多芯液晶光子晶体光纤,该光纤具有三个呈等边三角形几何形状排列的液晶纤芯。利用有限元法对其功率分布、模场、有效折射率和色散特性进行了数值分析,结果表明,这种三芯液晶光子晶体光纤可将传输光完全等分为三束光,且具有平坦色散特性,在波长为1.45μm~1.75μm之间的色散变化小于2 ps·km~(-1)·nm~(-1)。此外,该光纤在大约150 nm的波长范围内显示出超平坦的色散,并且可以通过改变中心空气孔的直径来调整超平坦色散的波长范围。研究成果对液晶光子晶体光纤、三轴光纤陀螺和三相光纤电流互感器的等光分束器、1×3多芯光子晶体耦合器和平坦色散光纤的进一步发展具有重要意义。     

光子晶体光纤陀螺光纤环偏振特性

光子晶体光纤陀螺技术是解决光纤陀螺空间辐照及热漂移问题的重要技术途径,其中光子晶体光纤环是影响光纤陀螺性能的关键。仿真分析了光子晶体光纤的双折射与结构设计的关系,并计算了光纤的双折射和光纤环绕制过程引入的附加双折射的温度灵敏度,利用白光干涉仪,对光子晶体光纤环和普通的保偏光纤环进行了对比测试分析。试验结果表明,光子晶体光纤环具有较低的偏振特性温度灵敏度,双折射温度系数比普通保偏光纤低接近1个量级,引起的陀螺偏振误差也比普通保偏光纤环小1倍左右。试验结果验证了理论分析的正确性。     

高精度光子晶体光纤陀螺设计及在轨应用验证

针对空间辐照带来的光功率衰减和卫星轨道周期带来的周期性温变效应,基于光子晶体光纤单一材料特点带来的抗辐照和弱温度敏感特性,提出开展空间用高精度光子晶体光纤陀螺技术研究.通过设计实芯光子晶体光纤结构,完成损耗<1.5 dB/km、偏振串音<-24 dB/km和直径135μm的光子晶体光纤技术验证,并采用八极对称绕制技术完...     

光子晶体光纤的耦合技术

光子晶体光纤与普通单模光纤的低损耗熔接是影响光子晶体光纤实用化的重要技术.针对自行设计的光子晶体光纤,对其与普通单模光纤的熔接损耗机制进行了理论和实验研究.首先分析了影响熔接损耗的主要因素,然后理论计算了光子晶体光纤与普通单模光纤之间的耦合损耗,最后采用常规电弧放电熔接技术对光子晶体光纤与单模光纤的熔接损耗进行了实验研究,通过优化放电参数,使熔接损耗可以降到0.7 dB以下,满足了实际应用的要求.该方法为其他类型的光子晶体光纤与普通单模光纤的熔接提供了借鉴.     

一种高性能抗辐照掺铒光子晶体光纤光源

为满足空间环境应用高精度光纤陀螺的需求,基于掺铒光子晶体光纤设计了一种抗辐照掺铒光纤光源。首先设计了一种高浓度掺铒光子晶体光纤,通过优化Er3+/Al3+的掺杂浓度,改善了掺铒光纤的荧光特性。然后通过调节光纤长度优化光源输出光谱接近掺铒光纤本征荧光谱,降低了辐照条件下掺铒光纤光源的光谱损耗;结合"平坦谱光谱滤波"和"泵浦光功率闭环反馈控制"技术设计出适合空间辐照环境应用的掺铒光子晶体光纤光源。辐照试验结果表明,光源在200 krad辐照剂量下输出光谱宽度大于40 nm,平均波长稳定性2.6′10~(-6)/krad,功率损耗小于0.2 dB,表现出较好的抗辐照效果。     

声子晶体L型波导高透射率拐角的设计

针对波导拐角处的透射及其能量损耗问题,本文设计了5种不同的拐角,应用在钢-水组分和铝-空气组分的声子晶体L型波导中;采用有限元方法,计算两种系统在不同频率范围内的透射率,并分析了带隙内缺陷态透射峰的振幅分布图。结果表明:采用直角形拐角,透射明显减弱;采用折线型拐角可以增强带隙内缺陷模的透射峰,也会产生新的带隙;采用环状弧形拐角,带隙内缺陷模的透射最强,且没有产生新的带隙。     

双折射材料初应力的定量研究相移等达因技术的应用

文章提出两种用相移等达因技术对存在于双折射材料内部的初始应力进行定量分析的方法，并以两种常用的双折射材料Ｐ６和Ｈｏｍａｌｉｔｅ１００为例进行了内部初应力的实验研究，给出了材料内部初应力的分布。以上研究说明双折射内部初始应力不容忽视，数字相移等达因技术是双折射材料内部初始应力进行定量分析的有力手段     

一种散光图象双折射相移的方法

由Pindera等提出了等达因法导出了平面问题的三个应力分量，可以非破坏性测取受力物体内部的应力状态，是一种有效的光测技术，应力分量与等达因条纹级次的导数相关，为得到具有高测试精度的应力分量在等达因条纹测试中引入了双折射相移技术，文中提出了一种在散光激光入射光路中用加入一可调偏振片和一可调1／4波片实现散光图象双折射相移的方法，该方法设备简单，能保证总体光强的一致性。     

Combined numerical simulation and nanoindentation for determining mechanical properties of single crystal copper at mesoscale

Constitutive laws are critical in the investigation of mechanical behavior of single crystal or polycrystalline materials in applications spanning from microscale to macroscale. In this investigation, a combined FEM simulation and experimental nanoindentation approach was taken to determine the mechanical behavior of single crystal copper incorporating the mesoplastic constitutive model. This model was implemented in a user-defined subroutine in 3D ABAQUS/Explicit code. Nanoindentation was modeled using the multiscale modeling technique involving mesoplasticity and elasticity, i.e., mesoplastic constitutive model was used near the local nanoindentation region (where the dislocations are generated) while elastic constitutive model was used in rest of the region in the workmaterial. The meso-mechanical behavior of the crystalline structure and the effect of the mesoplastic parameters on the nanoindentation load-displacement relationships were investigated in the FEM analysis. Nanoindentation tests were conducted on single crystal copper to determine load-displacement relationships. Appropriate mesoplastic parameters were determined by fitting the simulated load-displacement curves to the experimental data. The mesoplastic model, with appropriate parameters, was then used to determine the stress-strain relationship of a single crystal copper at meso-scale. The effect of indenter radius (3.4-) on material hardness under nanoindentation was simulated and found to match the experimental data for several indenter radii (3.4, 10 and ). A comparison of the topographies of nanoindentation impressions in the experiments with FEM results showed a reasonably good agreement.     

A finite element method for analysis of fluid flow,heat transfer and free interfaces in Czochralski crystal growth

A finite element algorithm is presented for simultaneous calculation of the steady state, axisymmetric flows and the crystal, melt/crystal and melt/ambient interface shapes in the Czochralski technique for crystal growth from the melt. The analysis is based on mixed Lagrangian finite element approximations to the velocity, temperature and pressure fields and isoparametric approximations to the interface shape. Galerkin's method is used to reduce the problem to a non-linear algebraic set, which is solved by Newton's method. Sample solutions are reported for the thermophysical properties appropriate for silicon, a low-Prandtl-number semiconductor, and for GGG, a high–Prandtl–number oxide material. The algorithm is capable of computing solutions for both materials at realistic values of the Grashof number, and the calculations are convergent with mesh refinement. Flow transitions and interface shapes are calculated as a function of increasing flow intensity and compared for the two material systems. The flow pattern near the melt/gas/crystal tri-junction has the asymptotic form predicted by an inertialess analysis assuming the meniscus and solidification interfaces are fixed.     

应用流体双折射方法计算二维二尖瓣模型的流场

本文运用流体双折射的实验数据与数值差分计算的杂交法对模拟二尖瓣模型的二维稳态流场进行定量计算,得到流场的流函数、速度等流场参量。     

The effects of micro-defects and crack on the mechanical properties of metal fiber sintered sheets

The effects of three types of defect (i.e., two micro defects—broken fibers and separation of fiber joints and one macro defect—crack) on the mechanical properties of porous metal fiber sintered sheets (MFSSs) are investigated by a combination of numerical simulation, analytical modeling, and experimental test. All simulations are based upon the previously developed micromechanics random beam model (Jin et al., 2013). Broken fibers are realized by removing cell edges (i.e., fibers between two joints) in an otherwise perfect model. Their induced decreases in the elastic moduli and strengths are found to be much lower than those of two dimensional (2D) foams and Kagome grids. For the defect in the form of separation of fiber joints, both analytical and numerical models are developed. The predicted linear decreases in the moduli and strengths (except for the compressive strength) with increasing number of separated fiber joints indicate that MFSSs be insensitive to the defect of joint separation. To explore the effect of crack, fracture toughness of MFSSs is measured and is found to be significantly higher than that of metal foams of the same relative density (i.e., volume fraction of the constituent solid material). The underlying ductile mechanism of MFSSs is further investigated by numerical simulations, showing that plastic deformation spreads all over the fibers in ligament rather than concentrates around crack tip. This study shows that MFSSs are superior in view of their resistance to the considered micro-defects and crack.