Polyacrylonitrile enzyme ultrafiltration and polyamide enzyme microfiltration membranes prepared by diffusion and convection

Glucose oxidase (GOD) and catalase (CAT) were covalently immobilized onto three types of polyacrylonitrile (PAN 1, PAN 2, and PAN 3) ultrafiltration (UF) membranes with different pore sizes and one type of polyamide (PA) microfiltration (MF) membrane by the bifunctional reagent, glutaraldehyde. The initial membranes were pre-modified to generate active amide groups in the PAN membranes and active amino groups in the PA membranes. The PAN 3 membrane contained the highest amount of active groups, and the membrane PA the lowest. The modified membranes were enzyme-loaded by diffusion and convection (UF). The effect of membrane pore size and immobilization methods on enzymatic activity and bound protein were studied. The most effective immobilized system was prepared by diffusion using a PAN 3 membrane as a carrier (bound protein: 0.055 mg/cm(2), relative activity: 87.6%). This membrane had the highest pore size of all the PAN membranes. Despite the highest pore size of PA membrane, the enzyme PA membranes prepared by diffusion showed the lowest amount of bound protein (0.03 mg/cm(2)) and the lowest relative activity (35.38%). This correlates with the lowest amount of active groups found in these membranes. The relative activity was higher for all the enzyme systems loaded by diffusion. The systems prepared by convection of the enzyme solution contained higher amounts of enzymes (0.035-0.13 mg/cm(2) protein), which led to internal substrate diffusion resistance and a decrease in the GOD relative activity (21.55-68.5%) in these systems. The kinetic parameters (V(max) and K(m)) and the glucose conversion of the immobilized systems prepared by diffusion were also studied. [diagram in text].     

Effect of supports for the direct oxidation of benzene to phenol over supported FeCl3 catalyst

The effect of supports on oxidation of benzene to phenol with hydrogen peroxide as an oxidant was tested by using supported FeCl₃ as catalysts. Their activities were affected by acid-base properties of supports. Silica gel which gave strong acid site near the active site had the highest activity among the investigated supports. Several kinds of silica gel which had different pore sizes were used. The maximum activity was obtained at the pore size of 3.5 nm and the reason was discussed.     

氨基化树枝状介孔二氧化硅固定葡萄糖氧化酶用于检测葡萄糖

以三乙胺为碱源合成了树枝状介孔二氧化硅纳米粒子（DMSNs），并用3-氨基丙基三乙氧基硅烷（APTES）进行氨基修饰合成了氨基化树枝状介孔二氧化硅纳米粒子（DMSNs-NH₂），将其用于葡萄糖氧化酶（GOD）的固定化研究.采用扫描电子显微镜、透射电子显微镜、红外光谱仪、X射线衍射仪、氮气吸附仪及热重分析仪对固定化GOD（DMSNs-NH₂-GOD）进行了表征，测定了其活性及蛋白载量.结果表明，固定化GOD的直径约为200 nm，形状均一，呈分散的球形微粒；在最佳固定条件下，蛋白载量达225 mg/g，酶活性达215 U/mg；固定化GOD检测葡萄糖的最低检测限为0.0014 mg/mL.利用固定化GOD检测了血清和饮料中的葡萄糖，重复使用36次以上其相对酶活性仍剩余80%.该方法操作方便、准确度高，提高了酶的pH稳定性、热稳定性及重复使用性，降低了检测成本.     

Technical and economic analysis of lignin conversion to methyl aryl ethers

Glucose oxidase (GOD) and Horseradish peroxidase (HRP) were covalently coupled to alkylamine controlled pore glass by means of glutaraldehyde. About 700-800 U/g of immobilized GOD and 300-400 U/g of immobilized HRP were obtained. Some factors of affecting enzyme immobilization were discussed. The immobilized enzymes were packed into a plastic tube and used in flow-injection analysis (FIA) for glucose in serum. A good linearity range was observed for this immobilized enzyme system at 20 mg/mL to 1000 mg/dL D-glucose, the recovery was 95.4-103.5%, the within-batch imprecision was 0.8-2.2%, and the between-batch imprecision was 2.2-4.2%. More than 100 samples were measured within an hour. One enzyme column with five units of immobilized GOD and HRP, applied for 50 assays/d, has been used for more than 2 mo.     

Reversible denaturation behavior of immobilized glucose oxidase

Glucose oxidase (GOD) was immobilized by using glutaraldehyde crosslinking and various stabilizing agents such as BSA, gelatin, lysozyme, and polyethylenimine (PEI). Studies on the denaturation of the soluble as well as immobilized GOD were carried out for 1 h at various concentrations of guanidine hydrochloride (GdmCl) in 50 mM phosphate buffer, pH 6.0 at 25±1°C. The soluble enzyme required a GdmCl concentration of 5M for total activity loss, whereas for GOD immobilized with BSA, gelatin, lysozyme, and heat-inactivated lysozyme, the corresponding GdmCl concentration required was 8 M. GOD immobilized with PEI, however, was more stable and retained 25% activity when denatured for 1 h using 8 M GdmCl. However, after undergoing denaturation for 1 h, GOD immobilized with lysozyme regained 72% original activity within 20 min of renaturation, while GOD immobilized with BSA, PEI, gelatin, and heat-inactivated lysozyme regained only 39, 21, 20, and 25% of activity, respectively. After five cycles of repeated denaturation and renaturation with 8 M GdmCl, GOD immobilized with lysozyme retained 70% of the original activity. Refolding ability of lysozyme, glutaraldehyde crosslinkages between lysozyme and GOD, together with ionic interactions between them, appear to play an important role in the denaturation-renaturation behavior of the immobilized enzyme.     

Gluconic acid production in bioreactor with immobilized glucose oxidase plus catalase on polymer membrane adjacent to anion-exchange membrane

Gluconic acid was obtained in the permeate side of the bioreactor with glucose oxidase (GOD) immobilized onto anion-exchange membrane (AEM) of low-density polyethylene grafted with 4-vinylpiridine. The electric resistance of the anion-exchange membranes was increased after the enzyme immobilization on the membrane. The gluconic acid productions were relatively low with the GOD immobilized by any method on the AEM. To increase the enzyme reaction efficiency, GOD was immobilized on membrane of AN copolymer (PAN) adjacent to an anion-exchange membrane in bioreactor. Uses of anion-exchange membrane led to selective removal of the gluconic acid from the glucose solution and reduce the gluconic acid inhibition. The amount of gluconic acid obtained in the permeate side of the bioreactor with the GOD immobilized on the PAN membrane adjacent to the AEM under electrodialysis was about 30 times higher than that obtained with enzyme directly bound to the AEM. The optimal substrate concentration in the feed side was found to be about 1 g/l. Further experiments were carried out with the co-immobilized GOD plus Catalase (CAT) on the PAN membrane adjacent to the AEM to improve the efficiency of the immobilize system. The yield of this process was at least 95%. The storage stability of the co-immobilized GOD and CAT was studied (lost 20% of initial activity for 90 d). The results obtained clearly showed the higher potential of the dual membrane bioreactor with GOD plus CAT bound to ultrafiltration polymer membrane adjacent to the AEM. Storage stability of GOD activity in GOD plus CAT immobilized on PAN//AEM membranes and on AEM.     

Polycaprolactone membranes reinforced by toughened sol–gel produced silica networks

The aim of this work is to develop polycaprolactone based porous materials with improved mechanical performance to be used in bone repair. The hybrid membranes consist in a polymeric porous material in which the pore walls are coated by a silica thin layer. Silica coating increases membrane stiffness with respect to pure polymer but in addition filling the pores of the polymer with a silica phase improves bioactivity due to the delivery of silica ions in the neighborhood of the material in vivo. Nevertheless silica network, even that produced by sol–gel, might be too stiff and brittle what is not desirable for its performance as a coating. In this work we produced a toughened silica coating adding chitosan and 3-glycidoxypropyltrimethoxysilane (GPTMS) to the precursor solution looking for having polymer chains linked by covalent bonding to the silica network. Hybrid polymer–silica coating was produced by in situ sol–gel reaction using Tetraethyl orthosilicate (TEOS), GPTMS and chitosan. Chemical reaction between amine groups of chitosan chains and epoxy groups of GPTMS allowed covalent bonding of polymer chains to the silica network. Physical properties of the hybrid membranes were characterized and cell attachment of MC3T3-E1 pre-osteoblastic cells on the surface of these supports was assessed.     

New approach to the immobilization of glucose oxidase on non-porous silica microspheres functionalized by (3-aminopropyl)trimethoxysilane (APTMS)

The immobilization and encapsulation of glucose oxidase (GOD) onto the mesoporous and the non-porous silica spheres prepared by co-condensation of tetraethylorthosilicate (TEOS) and (3-aminopropyl)trimethoxysilane (APTMS) in the water-in-oil (W/O) emulsion system were studied. The terminal amine group was used as the important functionality for GOD immobilization on the silica substrate. When only TEOS is used as a silica source, the disordered mesoporous silica microspheres are obtained. As the molar ratio of APTMS to TEOS (R_AT) increases, the surface area and pore volume of the silica particles measured by nitrogen adsorption and desorption method and SEM decrease rapidly. Particularly, the largest change of the surface morphology is observed between R_AT = 0.20 and R_AT = 0.25. The amount and the adsorption time of immobilized enzyme were measured by UV spectroscopy. About 20 wt% of GOD was immobilized into the silica substrates above R_AT = 0.60 and was completely adsorbed into the substrate of R_AT = 0.80 with lapse of 4 h after addition. In the measurement of the thermal stability, GOD dissolved in buffer solution loses nearly all of its activity after 30 min at 65 °C. In contrast, GOD immobilized on the surface-modified silica particles still retains about 90% of its activity after the same treatment. At this temperature, the immobilized glucose oxidase retained half of its initial activity after 4 h. It is shown that the suitable usage of functionalizing agent like APTMS as well as the control of surface morphology is very important on the immobilization of enzyme.     

A new application of humic substances: activation of supports for invertase immobilization

Invertase was immobilized on aminopropyl silica (APTS-SiO2) activated with humic substances (APTS-SiO2-HS) and on aminopropyl silica activated with glutaraldehyde (APTS-SiO2-GA). The resulting activity of both systems was compared. Humic substances (HS) used for the activation of the silica were extracted from soil of Cananéia, S?o Paulo State, Brazil, according to the procedure recommended by the International Humic Substances Society. Activity was determined by measuring the rate of formation of reduced sugars using the reaction with dinitrosalicylic acid (DNS). The amount of HS bound on the APTS-SiO2 was equal to 50 mg. The maximum amount of invertase immobilized on APTS-SiO2-HS was 15,200 U/g while in the system APTS-SiO2-GA it was 13,400 U/g. The experimental enzymatic activity was 3,700 and 3,300 U/g, for the systems APTS-SiO2-HS and APTS-SiO2-GA, respectively. Considering the increased amount and activity of immobilized enzyme compared with the glutaraldehyde method, it was concluded that this technique opens a new perspective in the preparation of supports for enzyme immobilization employing humic substances.     

固定化乙酰胆碱酯酶的制备及其特性研究

本研究以期研制出能重复使用的固定化乙酰胆碱酯酶(AChE),为天然产物复杂体系中AchE抑制剂筛选新方法的发展奠定基础.以氨基化硅胶(APS-Si)微球为载体,戊二醛为交联剂对乙酰胆碱酯酶进行交联固定化,并研究了酶的最佳固定化条件和固定化酶的性质.结果表明,0.05 g氨基化硅胶微球载体,用戊二醛溶液活化6 h后,在给酶量5 U,28℃固定16 h条件下,得到固定化酶的活性最大.固定化酶在常温(20～40℃),以及较宽pH范围内(pH 6～10)均具有较高的活性,并且具有良好的保存稳定性和可重复利用率,为基于固定化靶酶亲和-色谱质谱联用分析快速筛选乙酰胆碱酯酶抑制剂新方法的发展奠定了基础.     

不同介孔材料固定青霉素酰化酶的稳定性研究

介孔材料由于具有在2～30nm之间可调的纳米级规则孔道、大比表面积和强吸附性能而成为固定化酶的优良载体．将酶固定于介孔材料的孔道中制备成的固定化酶与溶液酶相比,有易于与产物分离,并可回收和反复使用,可降低生产成本,减少酶的自水解和保持酶的活性．青霉素酰化酶（Penicillin acylase,PGA,EC．3．5．1．11）又称为青霉素酰胺酶或青霉素氨基水解酶,该酶属于球蛋白,分子量较大,由2个亚基组成：分子量为19500的含有侧链结合位点的亚基和分子量为60000的含有催化位点的亚基．     

介孔材料MCFs的合成及组装青霉素酰化酶的性质研究

介孔材料由于具有纳米级规则孔道和巨大的比表面积而在催化、吸附及分离等方面存在较大的应用价值．近年来,由介孔分子筛如MCM-41和SBA-15州等组装功能性材料已成为研究的热点．酶作为高效催化剂有许多优点,但在溶液中易失活,使用后无法回收,有的酶在溶液中还存在自水解问题：将酶组装在介孔材料中制成固定化酶则可解决上述问题．目前已成功地将辣根过氧化物酶     

Immobilization of L-glutamate oxidase and peroxidase for glutamate determination in flow injection analysis system

Streptomyces SP.N 14, isolated from soil samples, produced extracellular L-glutamate oxidase (GOD) in liquid culture. After a two-step ammonium sulfate purification and dextran G-150 chromatography, the specific activity was reached at 28.2 U/mg. The partial purified enzyme and horseradish peroxidase (HRP) were covalently coupled to alkylamine controlled pore glass (CPG) by means of glutaraldehyde. About 200–300 U/g of immobilized GOD and 300–400 U/g of immobilized HRP were obtained. The immobilized enzymes were packed into a teflon tube and used in flow injection analysis (FIA) for glutamate in broth. A good linear range was observed for this immobilized enzyme system at 0.1–2.0 mM, and the precision was 2.8% (n = 25). More than 80 samples were measured within an hour. One enzyme column with about 4 U of immobilized GOD and 5 U of immobilized HRP, applied for 50 assays/d, has been used for more than 50 d. The concentration of L-glutamate remaining lower than 2.0 mM, the determination of glutamate in this system was not affected by pH and temperature within the range of 6.0–7.0 and 25–35‡C, respectively. The system was applied to determine L-glutamate in broth samples during L-glutamate fermentation, and good correlation was achieved between results obtained with the system and with the Warburg’s method.     

Comparison of <Emphasis Type="Italic">Yarrowia lipolytica</Emphasis> Lipase Immobilization Yield of Entrapment,Adsorption, and Covalent Bond Techniques

The purpose of this study was to immobilize lipase from Yarrowia lipolytica using three methods including inclusion, adsorption, and covalent bond to study enzyme leaching, storage, and catalytic properties. Sodium alginate and chitosan were the polymers selected to immobilize lipase by inclusion. The beads of each polymer were dried by freeze drying and fluidization. The results show that chitosan was more adapted to the inclusion of lipase. Even though freeze dried, bead activity was low compared to that of fluidized beads. The freeze-drying process seems to produce suitable beads for storage at 4 and 20 degrees C. The immobilization by adsorption was carried out on both celite and silica gel. Maximum immobilization yield of 76% was obtained with celite followed by 43% in silica gel. The enzyme adsorbed on the two supports exhibited greater stability at a certain temperature (50 degrees C) and in no polar solvents (Isooctane, n-heptane, and n-hexane). In addition, the lipase immobilized by covalent bond retained residual activity equitable to 70%. It was demonstrated that the enzyme immobilized by covalent bond showed greater activity (80%) after 5 months of storage.     

Properties of Immobilized Laccase on Mesostructured Cellular Foam Silica and its Use in Dye Decolorization

Laccase was immobilized on mesostructured cellular foam (MCF), a kind of mesoporous silica with large pore size by adsorption–cross linking method. The effects of immobilization time, temperature, pH, amount of enzyme and content of glutaraldehyde on the immobilization were optimized. The activities and stabilities towards pH and temperature of the immobilized enzyme were studied, and significantly improved enzymatic properties and good operational stability were obtained for the immobilized laccase. Dye decolorization tests showed that the immobilized enzyme could decolorize Alizarin Red and Indigo Blue solution fast and efficiently in the presence of ABTS.     

Aromatic amine coupling ofaspergillus niger lactase to controlled-pore silica witho-dianisidine

Lactose (β-galactosidase) derived fromAspergillus niger was immobilized on controlledpore silica with an average pore diameter of 425 Å. The coupling of this enzyme to the surface of the silica was accomplished by reacting the surface of the silica with o-dianisidine followed by the functionalization of the residual amine with glutaraldehyde or with nitrite to form the diazonium salt. The PH profiles of the immobilized enzymes were determined and compared. Continuous reactor studies of the glutaraldehyde-functionalized, immobilized enzyme indicated a half-life of 52 days at 50°C with a 5% lactose feed at pH 3.5.     

以陶瓷纤维为基材的硅胶吸附材料的制备与性能

以陶瓷纤维纸为基材，经水玻璃浸泡，絮凝剂沉积，盐酸调节pH值得到陶瓷纤维基硅胶吸附材料：探讨水玻璃浓度、絮凝剂浓度，盐酸浓度等条件对硅胶吸附剂吸附性能的影响：采用扫描电镜(SEM)，多孔介质孔隙分析仪揭示吸附材料的表面形貌、比表面积及孔径大小。实验结果显示：当水玻璃浓度为26．67wt%，絮凝剂浓度为15wt％，盐酸浓度为0．5mol／L时，吸附剂具有较好的吸附性能：硅胶能较好分散在纤维表面及其空隙中，BET比表面积为347．4m^2／g，总孔容为0．20295cm^2／g，其中，微孔所占比例为50．54％，平均孔径为，微孔0．4939nm，中孔3．907nm。     

A new application of humic substances: activation of supports for invertase immobilization

Invertase was immobilized on aminopropyl silica (APTS-SiO₂) activated with humic substances (APTS-SiO₂-HS) and on aminopropyl silica activated with glutaraldehyde (APTS-SiO₂-GA). The resulting activity of both systems was compared. Humic substances (HS) used for the activation of the silica were extracted from soil of Cananéia, São Paulo State, Brazil, according to the procedure recommended by the International Humic Substances Society. Activity was determined by measuring the rate of formation of reduced sugars using the reaction with dinitrosalicylic acid (DNS). The amount of HS bound on the APTS-SiO₂ was equal to 50 mg. The maximum amount of invertase immobilized on APTS-SiO₂-HS was 15200 U/g while in the system APTS-SiO₂-GA it was 13400 U/g. The experimental enzymatic activity was 3700 and 3300 U/g, for the systems APTS-SiO₂-HS and APTS-SiO₂-GA, respectively. Considering the increased amount and activity of immobilized enzyme compared with the glutaraldehyde method, it was concluded that this technique opens a new perspective in the preparation of supports for enzyme immobilization employing humic substances.     

Immobilization of glucoamylase onto novel porous polymer supports of vinylene carbonate and 2-hydroxyethyl methacrylate

Glucoamylase was immobilized onto novel porous polymer supports. The properties of immobilized glucoamylase and the relationship between the activity of immobilized enzyme and the properties of porous polymer supports were investigated. Compared with the native enzyme, the temperature profile of immobilized glucoamylase was widened, and the optimum pH was also changed. The optimum substrate concentration of immobilized glucoamylase was higher than that of native enzyme. After storage for 23 d, the immobilized glucoamylase still maintained about 84% of its initial activity, whereas the native enzyme only maintained about 58% of the initial activity. Moreover, after using repeatedly seven times, the immobilized enzyme maintained about 85% of its initial activity. Furthermore, the properties of porous polymer supports had an effect on the activity of the immobilized glucoamylase.     

A General Strategy for Site‐Directed Enzyme Immobilization by Using NiO Nanoparticle Decorated Mesoporous Silica

Mesoporous materials have recently gained much attention owing to their large surface area, narrow pore size distribution, and superior pore structure. These materials have been demonstrated as excellent solid supports for immobilization of a variety of proteins and enzymes for their potential applications as biocatalysts in the chemical and pharmaceutical industries. However, the lack of efficient and reproducible methods for immobilization has limited the activity and recyclability of these biocatalysts. Furthermore, the biocatalysts are usually not robust owing to their rapid denaturation in bulk solvents. To solve these problems, we designed a novel hybrid material system, mesoporous silica immobilized with NiO nanoparticles (SBA‐NiO), wherein enzyme immobilization is directed to specific sites on the pore surface of the material. This yielded the biocatalytic species with higher activity than free enzyme in solution. These biocatalytic species are recyclable with minimal loss of activity after several cycles, demonstrating an advantage over free enzymes.