A DNA electrochemical sensor prepared by electrodepositing zirconia on composite films of single-walled carbon nanotubes and poly(2,6-pyridinedicarboxylic acid), and its application to detection of the PAT gene fragment

Carboxyl group-functionalized single-walled carbon nanotubes (SWNTs) and 2,6-pyridinedicarboxylic acid (PDC) were electropolymerized by cyclic voltammetry on a glassy-carbon electrode (GCE) surface to form composite films (SWNTs/PDC). Zirconia was then electrodeposited on the SWNTs/PDC/GCE from an aqueous electrolyte containing ZrOCl₂ and KCl by cycling the potential between −1.1 V and +0.7 V at a scan rate of 20 mV s⁻¹. DNA probes with a phosphate group at the 5′ end were easily immobilized on the zirconia thin films, because of the strong affinity between zirconia and phosphate groups. The sensors were characterized by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). EIS was used for label-free detection of the target DNA by measuring the increase of the electron transfer resistance (R _et) of the electrode surface after the hybridization of the probe DNA with the target DNA. The PAT gene fragment and polymerase chain reaction (PCR) amplification of the NOS gene from transgenically modified beans were satisfactorily detected by use of this DNA electrochemical sensor. The dynamic range of detection of the sensor for the PAT gene fragment was from 1.0 × 10⁻¹¹ to 1.0 × 10⁻⁶ mol L⁻¹ and the detection limit was 1.38 × 10⁻¹² mol L⁻¹.     

Highly sensitive electrochemical impedance spectroscopic detection of DNA hybridization based on Aunano-CNT/PANnano films

A polyaniline nanofibers (PAN_nano)/carbon paste electrode (CPE) was prepared via dopping PAN_nano in the carbon paste. The nanogold (Au_nano) and carbon nanotubes (CNT) composite nanoparticles were bound on the surface of the PAN_nano/CPE. The immobilization and hybridization of the DNA probe on the Au_nano-CNT/PAN_nano films were investigated with differential pulse voltammetry (DPV) and cyclic voltammetry (CV) using methylene blue (MB) as indicator, and electrochemical impedance spectroscopy (EIS) using [Fe(CN)₆]^3−/4− as redox probe. The voltammetric peak currents of MB increased dramatically owing to the immobilization of the probe DNA on the Au_nano-CNT/PAN_nano films, and then decreased obviously owing to the hybridization of the DNA probe with the complementary single-stranded DNA (cDNA). The electron transfer resistance (R_et) of the electrode surface increased after the immobilization of the probe DNA on the Au_nano-CNT/PAN_nano films and rose further after the hybridization of the probe DNA. The remarkable difference between the R_et value at the DNA-immobilized electrode and that at the hybridized electrode could be used for the label-free EIS detection of the target DNA. The loading of the DNA probe on Au_nano-CNT/PAN_nano films was greatly enhanced and the sensitivity for the target DNA detection was markedly improved. The sequence-specific DNA of phosphinothricin acetyltransferase (PAT) gene and the polymerase chain reaction (PCR) amplification of nopaline synthase (NOS) gene from transgenically modified beans were determined with this label-free EIS DNA detection method. The dynamic range for detecting the PAT gene sequence was from 1.0 × 10⁻¹² mol/L to 1.0 × 10⁻⁶ mol/L with a detection limit of 5.6 × 10⁻¹³ mol/L.     

Fabrication of poly(2,6-pyridinedicarboxylic acid)/MWNTs modified electrode for simultaneous determination of guanine and adenine in DNA

The fabrication of poly(2,6-pyridinedicarboxylic acid)/MWNTs modified glass electrode(PPDA/MWNTs/GCE) was proposed and used for individual or simultaneous determination of guanine and adenine.The performances of the PPDA/MWNTs/GCE were characterized with cyclic voltammetry(CV).The modified electrode exhibited enhanced electrocatalytic behavior and good stability for the detection of guanine and adenine.Differential pulse voltammetry(DPV) was used to determine the concentration of guanine,adenine.The detection limit(S/N = 3) for guanine and adenine was 0.045μmol/L and 0.05μmol/L,respectively.The electrochemical method for the measurement of guanine and adenine in calf thymus DNA was also developed with this modified electrode and the result was satisfactory.     

Label-free detection of DNA molecules on the dendron based self-assembled monolayer by electrochemical impedance spectroscopy

We report preparation of a novel platform for effective DNA hybridization and its application to the detection of single mismatched DNA. Cone-shaped dendrimer molecules have been immobilized on the gold surface at equidistance, 3.1 nm, from each other with a probe DNA molecule attached to the top of each dendrimer so that enough space would be secured for effective hybridization. This arrangement allows each probe DNA molecule to form a natural DNA double helix upon hybridization with a target DNA molecule. The single nucleotide polymorphism at either the central or end position of the 25-mer target DNA has been shown to be effectively discriminated against on this platform from each other as well as from a complementary DNA by electrochemical impedance measurements. We also report adverse effects exerted by probe ions, Fe(CN)₆^3−/4−, on DNA hybridization reactions. The significance of the results for the use in DNA analysis is discussed.     

Simultaneous electrochemical DNA hybridization assay for PAT and FMV 35S gene sequence using quantum dots as labels

An electrochemical method for the simultaneous detection of two different DNA sequences from PAT and FMV 35S gene sequence using CdS and PbS quantum dots （QDs） as labels was described. The QDs were readily functionalized with oligonucleotides as electrochemical DNA probes and selectively hybridized to the complementary sequences immobilized on the microplate. The QDs anchored on the hybrids were dissolved in the solution by the oxidation of HNO3 and further detected by a sensitive differential pulse anodic stripping voltammetric method （DPASV）. The DPASV signals of the oxidation of Cd^2＋ and Pb^2＋ ions present in the solution were different and reflected the identity of corresponding ssDNA targets sequences.     

A PDDA/poly(2,6-pyridinedicarboxylic acid)-CNTs composite film DNA electrochemical sensor and its application for the detection of specific sequences related to PAT gene and NOS gene

2,6-Pyridinedicarboxylic acid (PDC) was electropolymerized on the glassy carbon electrode (GCE) surface combined with carboxylic group-functionalized single-walled carbon nanotubes (SWNTs) by cyclic voltammetry (CV) to form PDC-SWNTs composite film, which was rich in negatively charged carboxylic group. Then, poly(diallyldimethyl ammonium chloride) (PDDA), a linear cationic polyelectrolyte, was electrostatically adsorbed on the PDC-SWNTs/GCE surface. DNA probes with negatively charged phosphate group at the 5' end were immobilized on the PDDA/PDC-SWNTs/GCE due to the strong electrostatic attraction between PDDA and phosphate group of DNA. It has been found that modification of the electrode with PDC-SWNTs film has enhanced the effective electrode surface area and electron-transfer ability, in addition to providing negatively charged groups for the electrostatic assembly of cationic polyelectrolyte. PDDA plays a key role in the attachment of DNA probes to the PDC-SWNTs composite film and acts as a bridge to connect DNA with PDC-SWNTs film. The cathodic peak current of methylene blue (MB), an electroactive label, decreased obviously after the hybridization of DNA probe (ssDNA) with the complementary DNA (cDNA). This peak current change was used to monitor the recognition of the specific sequences related to PAT gene in the transgenic corn and the polymerase chain reaction (PCR) amplification of NOS gene from the sample of transgenic soybean with satisfactory results. Under optimal conditions, the dynamic detection range of the sensor to PAT gene target sequence was from 1.0x10(-11) to 1.0x10(-6) mol/L with the detection limit of 2.6x10(-12) mol/L.     

One saccharide sensor based on the complex of the boronic acid and the monosaccharide using electrochemical impedance spectroscopy

A novel saccharide sensor based on the covalent interaction between the boronic acid and saccharides was developed. Poly (aminophenylboronic acid) (PABA) was prepared by electropolymerizing 3-aminophenylboronic acid on gold electrode surface in acidic solution. The boronic acid group of the PABA film can form covalent-bond with different saccharides, which can change the dielectric characteristics of the PABA film, and the change of the dielectric characteristic was saccharides concentration dependent. Four kinds of saccharides could be detected by using electrochemical impedance spectroscopy. Good linear relationship and high sensitivity were obtained by this method.     

Study of the adsorption of cytochrome c on a gold nanoparticle – modified gold electrode by using cyclic voltammetry, electrochemical impedance spectroscopy and chronopotentiometry

Adsorption of cytochrome c (Cyt c) on a gold nanoparticle – modified gold electrode was studied by using cyclic voltammetry, electrochemical impedance spectroscopy and chronopotentiometry in a phosphate buffer solution. It is shown that the charge transfer resistance is directly proportional to the amount of adsorbed Cyt c. The effects of temperature and time on the course of adsorption were also studied. The trends obtained in ΔG_ADS showed that Cyt c was found to have a smaller affinity for the modified electrode as indicated by their smaller negative ΔG_ADS values.     

An electrochemical sensor based on TiO2/activated carbon nanocomposite modified screen printed electrode and its performance for phenolic compounds detection in water samples

Herein, we reported a titanium oxide (TiO₂) modified activated carbon nanocomposite that showed advantageous characteristics in terms of electro-conductivity, catalytic activity and surface area. The designed nanocomposite was employed to modify the screen printed carbon electrode transducer surface in the construction of an electrochemical sensor. The electrode surface modification was characterised by cyclic voltammetry and impedimetric studies. The modified transducer surface was subsequently used for the detection of four phenolic endocrine disruptors, p-nitrophenol, hydroquinone, catechol and 1-naphtol. Under optimal conditions, TiO₂ modified activated carbon sensor was evaluated by differential pulse voltammetry showing a good linearity with correlation coefficients higher than 0.99. It showed, in parallel, a high sensitivity where the detection limits were 348 ng/L, 110.1 ng/L, 3.3 ng/L and 7.2 µg/L for the respective studied compounds (S/N = 3). Finally, we validated the method with river water samples, and good recovery values were obtained showing the potential application of the reported biosensor.     

Multi-wall carbon nanotubes (MWCNTs)-doped polypyrrole DNA biosensor for label-free detection of genetically modified organisms by QCM and EIS

In this paper, we describe DNA electrochemical detection for genetically modified organism (GMO) based on multi-wall carbon nanotubes (MWCNTs)-doped polypyrrole (PPy). DNA hybridization is studied by quartz crystal microbalance (QCM) and electrochemical impedance spectroscopy (EIS). An increase in DNA complementary target concentration results in a decrease in the faradic charge transfer resistance (R_ct) and signifying “signal-on” behavior of MWCNTs-PPy-DNA system. QCM and EIS data indicated that the electroanalytical MWCNTs-PPy films were highly sensitive (as low as 4 pM of target can be detected with QCM technique). In principle, this system can be suitable not only for DNA but also for protein biosensor construction.     

Fabricating a reversible and regenerable electrochemical biosensor for quantitative detection of antibody by using “triplex-stem” DNA molecular switch

A reversible and regenerable electrochemical biosensor is fabricated for quantitative detection of antibody based on “triplex-stem” molecular switches. A hairpin-shaped oligonucleotide (hairpin DNA) labeled with ferrocene (Fc) at the 3′-end is fixed on the gold electrode serving as a signal transduction probe. Its hairpin structure leads Fc close to the surface of gold electrode and produces a strong current signal (on-state). A single-strand oligonucleotide modified with two digoxin molecules on the two arm segments (capture DNA) interact with hairpin DNA with the help of Ag⁺ ions. The “triplex-stem” DNA forms, which separates Fc from the electrode and reduces the electrochemical signal (off-state). Binding of digoxin antibody to digoxin releases capture DNA from the hairpin DNA, creating an effective “off-on” current signal switch. The stability of the “triplex-stem” structure of hairpin/capture DNA is critical to the signal switch and the sensitivity of the method, which can be adjusted conveniently and efficiently by changing Ag⁺ concentrations. Based on the “off-on” current signal switch, this biosensor is used to detect digoxin antibody sensitively in blood serum. The linear range is 1.0–500 pg with a correlation coefficient of 0.996, and the detection limit is 0.4 pg. Also, this biosensor shows excellent reversibility and reproducibility, which are significant requirements for practical biosensor applications.     

Sensitive DNA biosensor improved by Luteolin copper(II) as indicator based on silver nanoparticles and carbon nanotubes modified electrode

A novel and sensitive electrochemical DNA biosensor has been developed for the detection of DNA hybridization. The biosensor was proposed by using copper(II) complex of Luteolin C₃₀H₁₈CuO₁₂ (CuL₂) as an electroactive indicator based on silver nanoparticles and multi-walled carbon nanotubes (Ag/MWCNTs) modified glassy carbon electrode (GCE). In this method, the 4-aminobenzoic acid (4-ABA) and Ag nanoparticles were covalently grafted on MWCNTs to form Ag/4-ABA/MWCNTs. The proposed method dramatically increased DNA attachment quantity and complementary ssDNA detection sensitivity for its large surface area and good charge-transport characteristics. DNA hybridization detection was performed using CuL₂ as an electroactive indicator. The CuL₂ was synthesized and characterized using elemental analysis (EA) and IR spectroscopy. Cyclic voltammetry (CV) and fluorescence spectroscopy were used to investigate the interaction between CuL₂ and ds-oligonucleotides (dsDNA). It was revealed that CuL₂ presented high electrochemical activity on GCE, and it could be intercalated into the double helices of dsDNA. The target ssDNA of the human hepatitis B virus (HBV) was quantified in a linear range from 3.23 × 10⁻¹² to 5.31 × 10⁻⁹ M (r = 0.9983). A detection limit of 6.46 × 10⁻¹³ M (3σ, n = 11) was achieved.     

Synthesis of core-shell structured Au@Bi2S3 nanorod and its application as DNA immobilization matrix for electrochemical biosensor construction

The core-shell structured Au@Bi2S3 nanorods have been prepared through direct in-situ growth of Bi2S3 at the surface of pre-synthesized gold nanorods.The product was characterized by X-ray diffraction,transmission electron microscopy and energy-dispersive X-ray spectroscopy.Then the obtained Au@Bi2S3 nanorods were coated onto glassy carbon electrode to act as a scaffold for fabrication of electrochemical DNA biosensor on the basis of the coordination of-NH2 modified on 5’-end of probe DNA and Au@Bi2S3.Electrochemical characterization assays demonstrate that the Au@Bi2S3 nanorods behave as an excellent electronic transport channel to promote the electron transfer kinetics and increase the effective surface area by their nanosize effect.The hybridization experiments reveal that the Au@Bi2S3 matrix-based DNA biosensor is capable of recognizing complementary DNA over a wide concentration ranging from 10 fmol/L to 1 nmol/L.The limit of detection was estimated to be 2 fmol/L(S/N=3).The biosensor also presents remarkable selectivity to distinguish fully complementa ry sequences from basemismatched and non-complementary ones,showing great promising in practical application.     

On-line pre-concentration and UV determination of DNA fragments by dynamic coating capillary electrophoresis and its application to detection of genetically modified oilseed rape based on PCR

In this work, it was demonstrated that on-line pre-concentration and separation of DNA fragments within bared silica column by dynamic coating capillary electrophoresis and UV detection. The DNA fragments were pre-concentrated with long electrokinetic injecting time (99 s), peak height increased dramatically as a function of injection time, especially for shorter length DNA. The concentration sensitivity of DNA fragments can be improved from 20- to 100-fold relative to a normal injection (5 s). The electro-osmotic flow (EOF) and DNA-wall interactions within the capillary were eliminated effectively by dynamic coating method. Employing 0.5% poly(ethylene oxide) (PEO) in Tris-phosphate-EDTA (TBE) buffer as sieving matrix, DNA fragments, ranging from 11 to 657 bp, were separated within 20 min. The linear coefficient of linear relation between the migration and DNA length is 0.999. The DNA fragments amplified from transgenic oilseed rape by polymerase chain reaction (PCR) were separated and detected by this method, demonstrating the potential use of this method for effective DNA analysis and detection of genetically modified organisms (GMO).     

Switch-on fluorescence sensor for ascorbic acid detection based on MoS2 quantum dots-MnO2 nanosheets system and its application in fruit samples

In this work,molybdenum disulfide quantum dots(MoS_2 QDs) were firstly prepared by hydrothermal method using sodium molybdate and glutathione as precursors,and applied in ascorbic acid detection.When joining MnO_2 nanosheets into MoS_2 QDs solution,they produced an obvious fluorescence quenching,which should be due to inner filter effect(IFE).Meanwhile,the fluorescent probe was formed,Interestingly,we found that this quenching phenomenon disappeared with the addition of ascorbic acid,In other words,the fluorescence gradually restored.This recovery phenomenon is mainly due to the reduction effect of ascorbic acid for MnO_2 nanosheets.Under the optimum conditions,the limit of detection(LOD) of 39 nmol/L for ascorbic acid was achieved with a linear range of 0.33-5.00 μmol/L.The repeatability was better than 5.0% for ascorbic acid in both standard and fruit samples(n = 3).Moreover,the as-fabricated fluorescent sensing system was successfully employed to detect the ascorbic acid levels in hawthorn and jujube with satisfactory results.     

2-(2-Phenyl-1H-phenanthro-[9,10-d]imidazole-1-yl)-acetic acid (PPIA) and its application for determination of amines by high performance liquid chromatography with fluorescence detection and identification with mass spectroscopy/atmospheric pressure chemical ionization

A simple, sensitive, and mild method for the determination of amino compounds based on a condensation reaction with 1-ethyl-3-(3-dimethylaminopropyl)-carbodiimide hydrochloride (EDC·HCl) as the dehydrant with fluorescence detection has been developed. Amines were derivatized to their acidamides with labeling reagent 2-(2-phenyl-1H-phenanthro-[9,10-d]imidazole-1-yl)-acetic acid (PPIA). Studies on derivatization conditions indicated that the coupling reaction proceeded rapidly and smoothly in the presence of a base catalyst in acetonitrile to give the corresponding sensitively fluorescent derivatives with an excitation maximum at λ_ex 260 nm and an emission maximum at λ_em 380 nm. The labeled derivatives exhibited high stability and were enough to be efficiently analyzed by high-performance liquid chromatography. Identification of derivatives was carried out by online post-column mass spectrometry (LC/APCI-MS/MS) and showed an intense protonated molecular ion corresponding m/z [MH]⁺ under APCI in positive-ion mode. At the same time, the fluorescence properties of derivatives in various solvents or at different temperature were investigated. The method, in conjunction with a gradient elution, offered a baseline resolution of the common amine derivatives on a reversed-phase Eclipse XDB-C₈ column. LC separation for the derivatized amines showed good reproducibility with acetonitrile-water as mobile phase. Detection limits calculated from 0.78 pmol injection, at a signal-to-noise ratio of 3, were 3.1-18.2 fmol. The mean intra- and inter-assay precision for all amine levels were <3.85% and 2.11%, respectively. Excellent linear responses were observed with coefficients of >0.9996. The established method for the determination of aliphatic amines from real wastewater and biological samples was satisfactory.