Kinetics of Na|CF<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript> and Li|CF<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript> systems

Properties of CF _x /Li and CF _x /Na cells were examined while using galvanostatic charging/discharging, electrochemical impedance spectroscopy and scanning electron microscopy (SEM). The capacity during the first cycle was as high as ca. 1000 mAh g^?1. Such an electrode is suitable for primary CF _x /Li and CF _x /Na batteries. SEM images of CF _x cathode showed that during discharging it was transformed into amorphous carbon and LiF or NaF crystals (of diameter of ca. 5–20 μm). These systems (C?+?LiF or C?+?NaF) cannot be reversibly converted back into CF _x /Li or CF _x /Na, respectively. Exchange current densities are between 10^?7 Acm^?2 and 10^?9 Acm^?2 when working with LiPF₆ and NaPF₆ electrolytes (1.12?×?10^?7 Acm^?2 and 6.82?×?10^?9 Acm^?2, respectively). Those values are low and indicate that the charge transfer process may be the rate-determining step. Activation energies for the charge transfer process were 57 and 72 kJ mol^?1 for CF _x /LiPF₆ and CF _x /NaPF₆ systems, respectively. Higher activation energy barrier for the CF/Na⁺?+?e^??→?C?+?NaF reaction results in lower observed exchange current density in comparison to the system with lithium ions.     

Electrodeposition of Fe<Subscript> <Emphasis Type="Italic">x</Emphasis> </Subscript>Se<Subscript> <Emphasis Type="Italic">y</Emphasis> </Subscript> films from acidic solutions

Iron selenide (Fe_xSe_y) thin films were electrodeposited on a glassy carbon electrode (GCE) surface under constant potential and pulse potential modes. The deposition mechanism was investigated using cyclic voltammetry. Electrochemical processes at room temperature are accompanied by adsorption of selenium on the electrode surface and complicated by chemical reactions in the solution bulk. Several approaches to control the film stoichiometry were applied: varying of electrodeposition potential; the use of elevated temperatures (60–80°C) to decrease the electrode passivation and electrodissolution of interfering elements under pulse mode. The composition of Fe_xSe_y thin films was analyzed using an energy dispersive X-rays (EDX) analysis.     

Neutron diffraction study of dehydrogenation of titanium carbohydrides TiC<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>H<Subscript><Emphasis Type="Italic">y</Emphasis></Subscript>

The possibility of the synthesis of hydrogen-nonstoichiometric cubic titanium carbide ТiС _х of high purity from powdery nonstoichiometric cubic titanium carbohydride ТiС _х H _y or nonstoichiometric titanium carbide with admixture hydrogen by annealing in a continuously maintained vacuum of no worse than 1.33 × 10^–3 Pa at temperatures of 600–750°C for several hours has been shown. Similar annealing at higher temperatures (T ≥ 800°C) does not lead to the complete removal of hydrogen from a sample due to intensive sintering. In this case, it seems that pores between sintered particles are hydrogen traps, and the release of hydrogen through the surface of sintered particles is hindered.     

Phase transitions of the ZrNiH<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript> hydride

The hydrogen pressure-ZrNiH _x hydride composition isotherms were determined under isoplethic experiment conditions during the desorption and sorption of hydrogen. According to the experimental data, the ZrNiH _x -H₂ system (0 < x < 2.229) experienced two phase transitions, hydrogenolysis with the absorption of large amounts of hydrogen and the reverse transition to the initial state. It was found that the β phase existed in the ZrNiH _x -H₂ system at least up to 410°C, and the region of its homogeneity was shifted toward the α solution. The homogeneity region of the γ phase at 250°C on the side depleted of hydrogen extended to the composition x = 1.50, and the temperature of its peritectoid decomposition was above 250°C. The hydrogenolysis reaction proceeded with the formation of the ?-ZrH_3.153?x -NiZr_0.7H_0.3x system, which had a much higher (higher by 200–300 torr) partial hydrogen pressure over the temperature range 0–240°C, that is, was unstable with respect to the initial system.     

Si<Subscript>1-<Emphasis Type="Italic">x</Emphasis></Subscript>Ge<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>/Si Interface Profiles Measured to Sub-Nanometer Precision Using uleSIMS Energy Sequencing

The utility of energy sequencing for extracting an accurate matrix level interface profile using ultra-low energy SIMS (uleSIMS) is reported. Normally incident O₂ ⁺ over an energy range of 0.25–2.5 keV were used to probe the interface between Si_0.73Ge_0.27/Si, which was also studied using high angle annular dark field scanning transmission electron microscopy (HAADF-STEM). All the SIMS profiles were linearized by taking the well understood matrix effects on ion yield and erosion rate into account. A method based on simultaneous fitting of the SIMS profiles measured at different energies is presented, which allows the intrinsic sample profile to be determined to sub-nanometer precision. Excellent agreement was found between the directly imaged HAADF-STEM interface and that derived from SIMS.

Open image in new window

Graphical Abstract ?

     

Biomimetic synthesis of the arachidic acid/Ag<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>Cd<Subscript><Emphasis Type="Italic">y</Emphasis></Subscript>S nanocomposite films

Ag _x Cd _y S nanoparticles were obtained in arachidic acid (AA) monolayer containing Ag⁺ and Cd²⁺ under H₂S flow. The AA/Ag _x Cd _y S monolayers were deposited onto solid substrate to prepare LB films. The UV-vis spectrum showed that the LB film exhibited notable quantum-size effect. The small-angle X-ray diffraction revealed periodic structure of the LB films. The molar ratio of Ag to Cd in AA/Ag _x Cd _y S film was ca. 1 : 5 as measured by the XPS. TEM and FTIR spectroscopy showed that the head-groups of arachidic acid molecules controlled formation of Ag _x Cd _y S nanoparticles in the monolayer.     

Chemical composition-structure-properties relations in a series of Sr<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>Ba<Subscript>1-<Emphasis Type="Italic">x</Emphasis></Subscript>Nb<Subscript>2</Subscript>O<Subscript>6</Subscript> compounds

Based on structural studies of Sr _x Ba_1-x Nb₂O₆ crystals with different concentrations of strontium and barium, the structural causality of optical nonlinearity of these crystalline materials is established. YAG:Nd laser radiation of the crystals results in a monotonic decrease in the second harmonic intensity with increasing strontium concentration in a sample. Fine details of the structure responsible for this effect are determined.     

<Emphasis Type="Italic">Z</Emphasis>-and <Emphasis Type="Italic">E</Emphasis>-conformers of <Emphasis Type="Italic">N</Emphasis>-chloroacetylcytisine

N-Chloroacetylcytisine was synthesized by acylation of (–)-cytisine. Stable Z- and E-conformers with respect to rotational isomerism around the N-12–CO bond were found in PMR spectra at room temperature. The point at which PMR resonances of the Z- and E-conformers coalesced upon heating was measured. The transition barrier between the conformers was estimated.     

X-ray photoelectron and auger spectroscopic study of the chemical composition of BC<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>N<Subscript><Emphasis Type="Italic">y</Emphasis></Subscript> films

X-ray photoelectron and Auger spectroscopy are used to investigate the chemical composition of BC _x N _y films synthesized by PECVD from different initial gas mixtures in the temperature range 473–723 K. Main principles and features of the film formation are found. It is shown that the chemical composition of BC _x N _y films significantly depends on the synthesis parameters, which enables targeted control of their physical properties. The obtained data are discussed.     

Preparation of Pt-MO<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript> systems via oxidation of alloys

Supported platinum systems Pt-MO _x (M = Mo or Ce) were prepared by oxidizing Pt-Mo or Pt-Ce alloys of various compositions. The phase composition and crystal structure of samples before and after oxidative treatment were characterized by powder X-ray diffraction (XRD). Morphology was studied using scanning electron microscopy (SEM). The oxidation of Pt-Mo alloys or Pt-Ce intermetallic compounds yields Pt-MO _x systems in which nanosized platinum particles are homogeneously supported on metal oxide. This method can be used to synthesize Pt-MO _x systems with other transition or rare-earth elements and with various component concentrations.     

Properties of anodic RuNiO<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>(OH)<Subscript><Emphasis Type="Italic">y</Emphasis></Subscript> catalysts synthesized on carbon supports with various dispersion degree

A number of catalysts of the (Ru-Ni)/C system is synthesized and studied for application in anodes of alkaline ethanol-air fuel cells. The carbon supports used are carbon blacks with different specific surface area and graphite powders. The X-ray photoelectron spectroscopy technique allowed detecting on the catalyst surface metallic ruthenium and nickel in the form of Ni(OH)2 hydroxide and possibly oxyhydroxide NiOOH. It is shown that the catalyst activity in the reaction of ethanol electrochemical oxidation grows at an increase in the specific surface area of the carbon support. The method of carbon monoxide oxidative desorption was used to determine the values of the specific surface area of the catalyst metallic phase. It is shown that at an increase in the relative ruthenium content from (1Ru3Ni)/C to Ru/C, the specific catalytic activity in the catalysts of the (Ru-Ni)/C system reaches the maximum value near the composition of (2Ru1Ni)/C. It is shown that the found optimum catalyst composition is independent of the carbon support dispersion degree. Activity in ethanol electrooxidation of the (2Ru1Ni)/C catalyst supported on the Ketjenblack EC-600 carbon black is 18 ± 3 A/g of the catalyst (>120 A/g of Ru) at 40°C and potential E = 0.5 V in the 2MKOH + 1 M C₂H₅OH electrolyte.     

Spatial structure and stability of Mo<Subscript><Emphasis Type="Italic">n</Emphasis></Subscript>Si<Subscript><Emphasis Type="Italic">m</Emphasis></Subscript> nanoparticles

By means of the ab initio DMol³ method Mo _n Si _m nanoparticles and fragments of Mo₃Si and MoSi₂ crystal lattices are theoretically modeled. For both crystals a few neutral Mo₄Si₆ and Mo₆Si₆ fragments of different shapes and symmetry are considered. In each case, after cluster separation its geometry is optimized, as a result of which the geometric structure noticeably changes and its stability increases. In order to theoretically search for the spatial configurations of Mo₄Si₆ and Mo₆Si₆ nanoparticle, two approaches are used: 1) in the most stable Fe₄C₆ and Fe₆C₆ isomers found previously, iron and carbon atoms are replaced by molybdenum and silicon respectively and then the geometry is optimized to obtain new equilibrium distances and angles; 2) the search for main Mo₄Si₆ and Mo₆Si₆ configurations is performed using the binominal scheme, starting from Mo₂, MoSi, and Si₂ dimers. The nanoparticle structures are found to contain metal atom chains and isolated pairs and triples of silicon atoms. In most cases, the nanoparticle stability proves to be higher than that of the crystal clusters.     

Fabrication of a novel Li<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>MoO<Subscript><Emphasis Type="Italic">y</Emphasis></Subscript> film modified electrode and its application as an electrochemical sensor of iodate

A novel organic gel film modified electrode was simply and conveniently fabricated by casting Li_xMoO_y and polypropylene carbonate (PPC) onto the surface of a gold electrode. The cyclic voltammetry and amperometry studies demonstrated that the Li_xMoO_y film modified electrode has a high stability and a good electrocatalytic activity for the reduction of iodate. In amperometry, a good linear relationship between the steady current and the concentration of iodate was obtained in the range from 3×10^–7 to 1×10^–4 mol L^–1 with a correlation coefficient of 0.9997 and a detection limit of 1×10^–7 mol L^–1.     

The physicochemical and catalytic properties of the Pt-CeO<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript> system

The properties of the Pt-CeO _x system prepared by the oxidation of the Pt₂Ce intermetallic compound were studied. The sample was characterized by X-ray diffraction in situ, thermogravimetry, scanning electron microscopy (with an accessory for energy dispersion analysis), transmission electron microscopy, and temperature-programmed reduction with hydrogen. The catalytic properties of the sample were studied in the model reaction of toluene hydrogenation. The oxidation of the intermetallic compound caused the appearance of metallic platinum and cerium oxide phases and high-dispersity platinum particles encapsulated in cerium oxide. Metallic platinum on the surface of the catalyst experienced rapid deactivation in the presence of hydrogen sulfide; high-dispersity platinum particles encapsulated in cerium oxide exhibited enhanced stability toward sulfur compounds.     

A study of structural non-stoichiometry with respect to oxygen in <Emphasis Type="Italic">R</Emphasis>BaCo<Subscript>4</Subscript>O<Subscript>7+<Emphasis Type="Italic">x</Emphasis></Subscript> single crystals

Impurity-free RBaCo₄O_7+x (R = Y, Lu) crystals are grown and the evolution of their structure with varying oxygen concentration in the range 0 ≤ x ≤ 1.3 is studied. The structural features of the studied samples required to develop an extended strategy of the X-ray crystallographic experiment, which made it possible to obtain more accurate data on unit cell parameters and additional information on the features of superstructure modulation and diffuse scattering, along with the phase composition of crystalline samples. A crystal chemical analysis of the known structural models of RBaCo₄O_7+x is performed and suggestions are made about possible structural changes occurring when the oxygen concentration increases up to the limit.     

Halogenophilic and classical <Emphasis Type="Italic">Ad</Emphasis><Subscript><Emphasis Type="Italic">N</Emphasis></Subscript><Emphasis Type="Italic">E</Emphasis> mechanisms in nucleophilic vinylic substitution reactions involving the anions of transition metal carbonyls

The mechanism of the reaction of carbonylate anions ([M(CO) _n L]^–) with highly activated vinyl halides (Hal = Cl, Br, I) was investigated by the method of “anion traps” – the effect of proton donors on the composition of the reaction products. It was demonstrated that the reactions with PhCHal=C(Z)₂ (Hal = Br, I;Z=CN, CO₂Et) and PhCN=CClI take place through initial attack by the carbonylate at the halogen atom, the reactions with PhCCl=C(CO₂Et)₂ and PhCOCH=CHHal (Hal = Cl, I) take place through attack by the carbonylate at the π bond (Ad_NE mechanism), and in the case of E-and Z-PhCN=CHI the two mechanisms operate concurrently. The main laws determining the reaction mechanisms are analyzed.     

Oxidative dehydrogenation of <Emphasis Type="Italic">n</Emphasis>-butenes to 1,3-butadiene over BiMoFe<Subscript>0.65</Subscript>P<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript> catalysts: effect of phosphorous contents

A series of BiMoFe_0.65P _x oxide catalysts with varying phosphorous contents from 0.0 to 0.6 mol ratio were prepared by a co-precipitation method, and oxidative dehydrogenation (ODH) was carried out to produce 1,3-butadiene (BD) from n-butenes. The physico-chemical properties of the oxide catalysts were characterized by X-ray diffraction (XRD), Raman spectroscopy, N₂ sorption, and NH₃ and 1-butene temperature-programmed desorption (TPD). Among the catalysts studied here, BiMoFe_0.65P_0.1 oxide catalyst showed the highest conversion and selectivity to BD. From the result of 1-butene TPD, the higher catalytic activity is related to the amount of weakly bounded intermediate and the desorbing temperature of strongly bounded intermediates. Also, the higher catalytic activity likely originates from the acidity of the BiMoFe_0.65P_0.1 oxide catalyst; its acidity was higher than that of phosphorous-free oxide catalyst and further contained other oxide catalysts. BiMoFe_0.65P_0.1 oxide catalyst is stable and no significant deactivation for 100 h ODH reaction was shown.     

Hydrogenation and Dehydrogenation of the Clathrate Na<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>Si<Subscript>136</Subscript>

Samples of the clathrate Na _x Si₁₃₆ were saturated with hydrogen to 100 atm at 25°C in a Sievertstype apparatus and at pressures of 6 and 28 kbar in lentil-type high-pressure apparatuses at 100 and 250°C. X-ray powder diffraction analysis and Raman spectroscopy of the samples quenched after the saturation with hydrogen showed that the phase composition of the clathrates did not change. Heating of the quenched samples to room temperature in a thermal desorption setup produced not hydrogen, but hydrogen-containing gases, as we assumed, silanes. Heating to 650°C leads to decomposition of these compounds to form hydrogen.     

Evaluation of the <Emphasis Type="Italic">Q</Emphasis><Subscript><Emphasis Type="Italic">y</Emphasis></Subscript> absorption band maximum in a light-harvesting complex of the bacterial photosynthetic center <Emphasis Type="Italic">Thermochromatium tepidum</Emphasis>

Excitation energies of the bacteriochlorophyll (BChl) chromophores embedded in the photosynthetic light-harvesting complex of the purple bacterium Thermochromatium tepidum are computed using the time-dependent density functional theory based upon the fragmental molecular orbital (FMO-TDDFT) method. The results are correlated with the empirically based estimates of the Q _y absorption maximum, as well as with the observed large red shift induced by the binding of calcium.     

Accelerating <Emphasis Type="Italic">k</Emphasis><Subscript>0</Subscript>

Combining the powers of a fast pneumatic transport system and the Automatic Activation Analyzer (AAA) of the Atominstitut in Vienna with the newest version of the IAEA k ₀-Software, the application of the k ₀-method to the determination of short-lived radionuclides becomes easily possible. By calculating Asp-values with the IAEA software, the often expensive and time-consuming measurement of Asp-values using certified reference materials is reduced to quality control checks. Measurements clearly show that the two approaches are equivalent, especially since both take self-absorption and neutron self-shielding into account. In this way it is possible to expand the library of the AAA with many hitherto unobtainable Asp-values. At the same time, using highly accurate Asp-values already measured for many short-lived radionuclides, k ₀-values for those can be produced with a simple procedure.