Analysis of sterilization effect by pulsed dielectric barrier discharge

Atmospheric pressure (AP) plasmas can sterilize against almost all kinds of bacteria because many ions and reactive species, such as oxygen atoms and ozone, etc., are generated during AP plasmas. So AP plasmas are proper processes for application to air cleaners and sterilizers. The aim of this paper is to evaluate a germicidal effect caused by pulsed plasma system in air utilizing a dielectric barrier discharge (DBD) type reactor incorporating alumina, glass, etc. Escherichia coli, Bacillus subtilis and Pseudomonas aeruginosa bacteria were used for this sterilization experiment. For analysis of the relationship between sterilization results and chemical species generated in the discharge, we used optical emission spectroscopy and we checked emission spectra by atomic oxygen (394.2 and 436.8 nm) and second positive system of nitrogen (337.1 nm). Experimental results showed that DBD treatment during 70 s sterilized E. coli with 99.99% effectively and ozone molecules were the dominant germicidal species. From these results we concluded that the pulsed DBD system is very effective for sterilization.     

Inactivation of Escherichia coli and properties of medical poly(vinyl chloride) in remote-oxygen plasma

This paper reports the germicidal effect (GE) of Escherichia coli on the surface of medical poly(vinyl chloride) (PVC) in remote-oxygen plasma. The concentration of active species in plasma is determined by means of double Langmuir electron probe and electron-spin resonance (ESR) diagnosis. Moreover, surface properties of sterilized PVC are characterized by the water contact angle measurement, X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM). The distribution of electrons, ions, and radicals in plasma reactor is different. High-purity radicals are obtained at 40 cm from the induction coil which is called remote-plasma zone. By remote-oxygen-plasma sterilization, GE value reach 4.12 under the conditions of treatment time of 60 s, plasma RF power of 100 W and oxygen flux of 60 cm³/min. Compared with direct-oxygen-plasma sterilization, remote plasma can enhance the hydrophilic property and limit the degradation of the PVC surface. After remote-plasma sterilization, PVC surface energy is increased more than twice, which mainly resulted from the increase of surface polar force , and hydrogen bonding force . Moreover, remote-plasma sterilization can increase oxygenated functional groups on PVC surface. Experimental results show that remote plasma can inactivate E. coli on the medical PVC substrate effectively. Furthermore, it can optimize the surface properties.     

Long-distance oxygen plasma sterilization: Effects and mechanisms

The distribution of electrons, ions and oxygen radicals in long-distance oxygen plasma and the germicidal effect (GE) of Escherichia coli on the surface of medical poly(tetrafluoroethylene) (PTFE) film were studied. The quantity of protein leakage and the production of lipid peroxide in bacterial suspension as well as the state of DNA were measured after sterilization to analyse the inactivation mechanisms. The results showed that the concentration of electrons and ions decreased rapidly with increasing the distance from the center of induction coil, which approximated to 0 at 30 cm, whereas the concentration of oxygen radicals reduced slowly, i.e. decreased 30% within 40 cm. GE value reached 3.42 in the active discharge zone (0 cm) and exceeded 3.32 within 40 cm when plasma treatment parameters were set as follows: plasma rf power at 100 W, treatment time at 60 s and oxygen flux at 40 cm³/min. Fast etching action on cell membrane by electrons, ions and attacking polyunsaturation fatty acid (PUFA) in cell membrane by oxygen radicals are primary reasons of oxygen plasma sterilization in the active discharge and the afterglow zone, respectively. The GE of UV radiation in long-distance oxygen plasma is feebleness.     

Surface modification of Angora rabbit fibers using dielectric barrier discharge

Dielectric barrier discharge (DBD) of Helium and Helium + air modify the surface of Angora rabbit fibers. DBD treatment carried out at different power densities, changes the morphology and chemical composition of the surface of Angora fiber. Scanning electron microscopy (SEM) results reveal that the DBD treatment eliminates fibrosity from the fiber surface. X-ray photoelectron spectroscopy and Fourier transform infrared spectrometer (FTIR) spectrum confirm the increase in oxygen bonding at the surface. These changes reduce shedding of the fibers and improve dye-uptake property. However, even after 10 min of plasma exposure the thermal insulation (heat keeping ratio) of Angora fibers nearly remain unchanged. It has been noticed that DBD treatment (10 min) reduces whiteness of the fiber.     

Real-time quantification of Staphylococcusaureus in liquid medium using infrared thermography

We previously showed that infrared thermography (IRT) could be used to quantify viable Escherichiacoli, a representative gram-negative bacterium, in liquid growth media. Here, we evaluated the ability of IRT to enumerate a viable representative gram-positive organism, Staphylococcusaureus. We found that the energy content (EC) of the media was strongly positively correlated (r = 0.999) to measured viable counts of S.aureus ranging from 85 colony-forming units (CFU)/ml to ∼4 × 10⁸ CFU/ml. The EC of S.aureus was ∼2-fold higher than that of E.coli at comparable cell concentrations suggesting that IRT may be used to distinguish genera.     

Effects of dielectric barrier discharge in air on morphological and electrical properties of graphene nanoplatelets and multi-walled carbon nanotubes

Multi-walled carbon nanotubes (MWCNTs) and graphene nanoplatelets (GNPs) have been functionalized by dielectric barrier discharge (DBD) in air. The extent of functionalization of MWCNTs and GNPs reaches a maximum at the delivered discharge energy of 720 and 240 J mg⁻¹, respectively. Further exposure to plasma leads to reduction of functional groups from the surface of the treated nanomaterials. It has also been demonstrated that DBD plasma does not produce dramatic structural changes in MWCNTs, while flakes of the treated GNPs become thinner and smaller in the lateral size. Conductive thin films, obtained by drop casting a solution of the treated nanomaterials in N-methyl-1-pyrrolidone on poly(methyl methacrylate) substrate, show significantly lower sheet resistance.     

Far UVC light for E. coli disinfection generated by carbon nanotube cold cathode and sapphire anode

Ultraviolet germicidal irradiation (UVGI) is an effective technique that can sterilize bacteria and viruses by UV light. Far UVC lamps of short wavelengths can prevent infectious diseases because they sterilize while minimizing cell damage in mammals. Here, E. coli inactivation by far UVC light with peak wavelength of 230 nm made of carbon nanotube (CNT) emitters and sapphire anode was studied. The κ-Al₂O₃ phase of sapphire with a direct band gap of 5.4 eV was excited with CNT-based cold cathode electron beam (C-beam) to generate far UVC light. It was confirmed that the inactivation of E. coli by far UVC light based on the C-beam was reduced by 5 log reduction within 60 s.     

Effects of dielectric barrier discharge plasma on pathogen inactivation and the physicochemical and sensory characteristics of pork loin

This study aimed to evaluate the use of a dielectric barrier discharge (DBD) plasma system to improve the safety of pork loins. When pork loin was exposed to DBD plasma with the input gases He and He + O₂, the population of Escherichia coli was reduced by 0.26 and 0.50 log cycles following a 5-min treatment and by 0.34 and 0.55 log units following a 10-min treatment, respectively. That of Listeria monocytogenes was also reduced from 0.17 to 0.35 and 0.43 to 0.59 log cycles when the samples were exposed to DBD for 5 and 10 min using He and He + O₂, respectively. The pH and L*-values (lightness) of the samples decreased significantly with DBD plasma treatment, but a*- (redness) and b*-values (yellowness) exhibited no obvious changes. Lipid oxidation, measured by TBARS values, was greater in samples with He + O₂ than in other samples. Significant reductions in sensory quality parameters (appearance, color, odor, acceptability, etc.) were observed in DBD-treated samples. These results indicate that the DBD plasma system has potential for use in sanitizing pork loins by inactivation of foodborne pathogens, although the effect was limited. In order to meet market requirements, however, a method to overcome sensory deterioration of pork loins should be developed and applied.     

Surface modification of polyimide films using unipolar nanosecond-pulse DBD in atmospheric air

DBD-induced surface modification is very versatile to increase the adhesion or hydrophilicity of polymer films. In this paper, the DBD is produced by repetitive unipolar nanosecond pulses with a rise time of 15 ns and a full width at half maximum of about 30 ns. The power densities of the homogeneous and filamentary DBDs during plasma treatment are 158 and 192 mW/m², respectively, which are significantly less than that using ac DBD processing, and the corresponding plasma dose is also mild compared to AC DBD treatment. Surface treatment of polyimide films using the homogeneous and filamentary DBDs is studied and compared. The change of chemical and physical modification of the surface before and after plasma processing has been evaluated. It can be found that both surface morphology and chemical composition are modified, and the modification includes the rise of hydrophilicity, surface oxidation and the enhancement of surface roughness. Furthermore, the homogeneous DBD is more effective for surface processing than the filamentary DBD, which can be attributed to the fact that the homogeneous DBD can modify the surface more uniformly and introduce more polar functional groups.     

Electrical characterization of dielectric barrier discharge driven by repetitive nanosecond pulses in atmospheric air

Dielectric barrier discharge (DBD) is an important method to produce non-thermal plasma, which has been widely used in many fields. In the paper, a repetitive nanosecond-pulse generator is used for the excitation of DBD. Output positive pulse of the generator has a rise time of about 15 ns and a full width at half maximum of 30–40 ns, and pulse repetition frequency varies from single shot to 2 kHz. The purpose of this paper is to experiment the electrical characteristics of DBD driven by repetitive nanosecond pulses. The variables affecting discharge conditions, including air gap spacing, dielectric thickness, barrier fashion, and applied pulse repetition frequency, are investigated. The relationship between electric field, discharge current, instantaneous discharge power across air gap, and estimated electron density with the length of air gap, dielectric thickness, barrier fashion, and pulse repetition frequency is obtained respectively, and the experimental results are also discussed. In addition, two typical images exhibiting homogeneous and filamentary discharges are given with different experimental conditions.     

Annealing effect on the structural and optical properties of a Cd1−xZnxS thin film for photovoltaic applications

Herein is a report of a study on a Cd_1−xZn_xS thin film grown on an ITO substrate using a chemical bath deposition technique. The as-deposited films were annealed in air at 400 °C for 30 min. The composition, surface morphology and structural properties of the as-deposited and annealed Cd_1−xZn_xS thin films were studied using EDX, SEM and X-ray diffraction techniques. The annealed films have been observed to possess a crystalline nature with a hexagonal structure. The optical absorption spectra were recorded within the range of 350-800 nm. The band gap of the as-deposited thin films varied from 2.46 to 2.62 eV, whereas in the annealed film these varied from 2.42 to 2.59 eV. The decreased band gap of the films after annealing was due to the improved crystalline nature of the material.     

The research on the interfacial compatibility of polypropylene composite filled with surface treated carbon fiber

Dielectric barrier discharges (DBD) in ambient air are used on carbon fiber to improve the fiber surface activity. Carbon fibers with length of 75 μm are placed into the plasma configuration. The interaction between modified carbon fibers and polypropylene (PP) was studied by three-point bending (TPB) test. The chemical changes induced by the treatments on carbon fiber surface are examined using X-ray photoelectron spectroscopy (XPS). XPS results reveal that the carbon fiber modified with the DBD at atmospheric pressure show a significant increase in oxygen and nitrogen concentration. These results demonstrate that the surface of the carbon fiber is more active and hydrophilic after plasma treatments using a DBD operating in ambient air.     

Influence of Gap Spacing between Dielectric Barriers in Atmospheric Pressure Discharges

The breakdown activity in helium atmospheric pressure dielectric barrier discharge (DBD) plasma is strongly modified by introducing small impurities (nitrogen (N₂) and air in ppm), although its precise implications for the behavior of discharge plasma is not evident under several constraints. In this simulation study, we investigate the influence of gap spacing between the dielectric barriers to explore the dynamic modification in the structure of discharge plasma in distinct phases of the discharge current pulse using a two‐dimensional fluid model in He‐air gas mixture. Specifically, the impact of nitrogen and air impurities is contrasted by exploring the spatial distributions of electrons in the breakdown phase under similar operating conditions. The filamentary mode of DBD plasma in He‐N₂ is transformed into uniform glow discharge in He‐air gas mixture by the dominant effect of Penning ionization. Finally, the outcomes of two‐dimensional fluid model are validated by comparing with three‐dimensional fluid model to provide the reliability of numerical simulations. (© 2015 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Ultrasound treatment enhances cholesterol removal ability of lactobacilli

This study aimed to evaluate the effect of ultrasound treatment on the cholesterol removing ability of lactobacilli. Viability of lactobacilli cells was significantly increased (P < 0.05) immediately after treatment, but higher intensity of 100 W and longer duration of 3 min was detrimental on cellular viability (P < 0.05). This was attributed to the disruption of membrane lipid bilayer, cell lysis and membrane lipid peroxidation upon ultrasound treatment at higher intensity and duration. Nevertheless, the effect of ultrasound on membrane properties was reversible, as the viability of ultrasound-treated lactobacilli was increased (P < 0.05) after fermentation at 37 °C for 20 h. The removal of cholesterol by ultrasound-treated lactobacilli via assimilation and incorporation of cholesterol into the cellular membrane also increased significantly (P < 0.05) upon treatment, as observed from the increased ratio of membrane C:P. Results from fluorescence anisotropies showed that most of the incorporated cholesterol was saturated in the regions of phospholipids tails, upper phospholipids, and polar heads of the membrane bilayer.     

Fabrication and characterization of La-doped HfO2 gate dielectrics by metal-organic chemical vapor deposition

La-doped HfO₂ gate dielectric thin films have been deposited on Si substrates using La(acac)₃ and Hf(acac)₄ (acac = 2,4-pentanedionate) mixing sources by low-pressure metal-organic chemical vapor deposition (MOCVD). The structure, thermal stability, and electrical properties of La-doped HfO₂ films have been investigated. Inductive coupled plasma analyses confirm that the La content ranging from 1 to 5 mol% is involved in the films. The films show smaller roughness of ∼0.5 nm and improved thermal stability up to 750 °C. The La-doped HfO₂ films on Pt-coated Si and fused quartz substrates have an intrinsic dielectric constant of ∼28 at 1 MHz and a band gap of 5.6 eV, respectively. X-ray photoelectron spectroscopy analyses reveal that the interfacial layer is Hf-based silicate. The reliable value of equivalent oxide thickness (EOT) around 1.2 nm has been obtained, but with a large leakage current density of 3 A/cm² at V_g = 1V + V_fb. MOCVD-derived La-doped HfO₂ is demonstrated to be a potential high-k gate dielectric film for next generation metal oxide semiconductor field effect transistor applications.     

Characterization of undoped and Co doped ZnO nanoparticles synthesized by DC thermal plasma method

ZnO nanopowders doped with 5 and 10 at% cobalt were synthesized and their antibacterial activity was studied. Cobalt doped ZnO powders were prepared using dc thermal plasma method. Crystal structure and grain size of the particles were characterized by X-ray diffractometry and optical properties were studied using UV-vis spectroscopy. The particle size and morphology was observed by SEM and HRTEM, revealing rod like morphology. The antibacterial activity of undoped ZnO and cobalt doped ZnO nanoparticles against a Gram-negative bacterium Escherichia coli and a Gram-positive bacterium Bacillus atrophaeus was investigated. Undoped ZnO and cobalt doped ZnO exhibited antibacterial activity against both E. coli and Staphylococcus aureus but it was considerably more effective in the cobalt doped ZnO.     

Surface treatment of aramid fiber by air dielectric barrier discharge plasma at atmospheric pressure

Aramid fiber samples are treated by air dielectric barrier discharge (DBD) plasma at atmospheric pressure; the plasma treatment time is investigated as the major parameter. The effects of this treatment on the fiber surface physical and chemical properties are studied by using surface characterization techniques. Scanning electron microscopy (SEM) is performed to determine the surface morphology changes, X-ray photoelectron spectroscopy (XPS) is analyzed to reveal the surface chemical composition variations and dynamic contact angle analysis (DCAA) is used to examine the changes of the fiber surface wettability. In addition, the wetting behavior of a kind of thermoplastic resin, poly(phthalazinone ether sulfone ketone) (PPESK), on aramid fiber surface is also observed by SEM photos. The study shows that there seems to be an optimum treatment condition for surface modification of aramid fiber by the air DBD plasma. In this paper, after the 12 s, 27.6 W/cm³ plasma treatment the aramid fiber surface roughness is significantly improved, some new oxygen-containing groups such as C-O, CO and OC-O are generated on the fiber surface and the fiber surface wettability is greatly enhanced, which results in the better wetting behavior of PPESK resin on the plasma-treated aramid fiber.     

Surface microstructures and antimicrobial properties of copper plasma alloyed stainless steel

Bacterial adhesion to stainless steel surfaces is one of the major reason causing the cross-contamination and infection in many practical applications. An approach to solve this problem is to enhance the antibacterial properties on the surface of stainless steel. In this paper, novel antibacterial stainless steel surfaces with different copper content have been prepared by a plasma surface alloying technique at various gas pressures. The microstructure of the alloyed surfaces was investigated using glow discharge optical emission spectroscopy (GDOES) and scanning electron microscopy (SEM). The viability of bacteria attached to the antibacterial surfaces was tested using the spread plate method. The antibacterial mechanism of the alloyed surfaces was studied by X-ray photoelectron spectroscopy (XPS). The results indicate that gas pressure has a great influence on the surface elements concentration and the depth of the alloyed layer. The maximum copper concentration in the alloyed surface obtained at the gas pressure of 60 Pa is about 7.1 wt.%. This alloyed surface exhibited very strong antibacterial ability, and an effective reduction of 98% of Escherichia coli (E. coli) within 1 h was achieved by contact with the alloyed surface. The maximum thickness of the copper alloyed layer obtained at 45 Pa is about 6.5 μm. Although the rate of reduction for E. coli of this alloyed surface was slower than that of the alloyed surface with the copper content about 7.1 wt.% over the first 3 h, few were able to survive more than 12 h and the reduction reached over 99.9%. The XPS analysis results indicated that the copper ions were released when the copper alloyed stainless steel in contact with bacterial solution, which is an important factor for killing bacteria. Based on an overall consideration of bacterial killing rate and durability, the alloyed surface with the copper content of 2.5 wt.% and the thickness of about 6.5 μm obtained at the gas pressure of 45 Pa is expected to be useful as antimicrobial materials that may have a promising future in antimicrobial applications.     

Comparison of experiment and simulation on dielectric barrier discharge driven by 50 Hz AC power in atmospheric air

Dielectric barrier discharge (DBD) is an important method to produce non-thermal plasma, and the excitation using 50 Hz power source is a convenient choice. In the paper, a comparison of simulation and experiment on the DBD produced by 50 Hz power source is given. For the simulation, an electrical model and a voltage-controlled current source are used to simulate the DBD and the dynamic of microdischarges, respectively. As to the experiment, a plane-parallel configuration DBD is driven by 50 Hz power in atmospheric air. It can be found that the measured voltage, current–time and voltage–charge waveforms are consistent with the simulated results. The variation of the discharge power and transported charges as a function of voltage amplitude, gap spacing, and barrier thickness is presented. The quantitative comparison of the experimental and simulated data confirms the validity of the electrical model. In addition, some discussions are given for the experimental and simulated results.     

Structural, optical properties and VCNR mechanisms in vacuum evaporated iodine doped ZnSe thin films

Iodine doped ZnSe thin films were prepared onto uncoated and aluminium (Al) coated glass substrates using vacuum evaporation technique under a vacuum of 3 × 10⁻⁵ Torr. The composition, structural, optical and electrical properties of the deposited films were analyzed using Rutherford backscattering spectrometry (RBS), X-ray diffraction (XRD), spectroscopic ellipsometry (SE) and study of I-V characteristics, respectively. In the RBS analysis, the composition of the deposited film is calculated as ZnSeI_0.003. The X-ray diffractograms reveals the cubic structure of the film oriented along (1 1 1) direction. The structural parameters such as crystallite size, strain and dislocation density values are calculated as 32.98 nm, 1.193 × 10⁻³ lin⁻² m⁻⁴ and 9.55 × 10¹⁴ lin/m², respectively. Spectroscopic ellipsometric (SE) measurements were also presented for the prepared iodine doped ZnSe thin films. The optical band gap value of the deposited films was calculated as 2.681 eV by using the optical transmittance measurements and the results are discussed. In the electrical studies, the deposited films exhibit the VCNR conduction mechanism. The iodine doped ZnSe films show the non-linear I-V characteristics and switching phenomena.