Structural properties of the titanium dioxide thin films grown by atomic layer deposition at various numbers of reaction cycles

A dependence of structural properties of TiO₂ films grown on both Si- and Ti-substrates by atomic layer deposition (ALD) at the temperature range of 250-300 °C from titanium ethoxide and water on the number of reaction cycles N was investigated using Fourier-transform infrared (FTIR) spectroscopy and X-Ray diffraction (XRD). TiO₂ films grown on both Si- and Ti-substrates revealed amorphous structure at low values of N < 400. However, an increase of N up to values 400-3600 resulted in the growth of polycrystalline TiO₂ with structure of anatase on both types of substrates and according to XRD-measurements the sizes of crystallites rose with the increase of N. The maximum anatase crystallite size for TiO₂ grown on Ti-substrate was found to be on ∼35% lower in comparing with that for TiO₂ grown on Si-substrate. A use of titanium methoxide as a Ti precursor with the ligand size smaller than in case of titanium ethoxide allowed to observe an influence of the ligand size on both the growth per cycle and structural properties of TiO₂. The average growth per cycle of TiO₂ deposited from titanium methoxide and water (0.052 ± 0.01 nm/cycle) was essentially higher than that for TiO₂ grown from titanium ethoxide and water (0.043 ± 0.01 nm/cycle). Ligands of smaller sizes were found to promote the higher crystallinity of TiO₂ in comparison with the case of using the titanium precursor with ligands of bigger sizes.     

Self-limiting growth of ZnO films on (0 0 0 1) sapphire substrates by atomic layer deposition at low temperatures using diethyl-zinc and nitrous oxide

Atomic layer deposition (ALD) of zinc oxide (ZnO) films on (0 0 0 1) sapphire substrates was conducted at low temperatures by using diethyl-zinc (DEZn) and nitrous oxide (N₂O) as precursors. It was found that a monolayer-by-monolayer growth regime occurred at 300 °C in a range of DEZn flow rates from 5.7 to 8.7 μmol/min. Furthermore, the temperature self-limiting process window for the ALD-grown ZnO films was also observed ranging from 290 to 310 °C. A deposition mechanism is proposed to explain how saturated growth of ZnO is achieved by using DEZn and N₂O. Transmission spectroscopic studies of the ZnO films prepared in the self-limiting regime show that the transmittances of ZnO films are as high as 80% in visible and near infrared spectra. Experimental results indicate that ZnO films with high optical quality can be achieved by ALD at low temperatures using DEZn and N₂O precursors.     

Atomic layer deposition of HfO2: Effect of structure development on growth rate, morphology and optical properties of thin films

HfO₂ films were grown by atomic layer deposition from HfCl₄ and H₂O on Si(1 0 0), Si(1 1 1) and amorphous SiO₂ substrates at 180-750 °C and the effect of deposition temperature and film thickness on the growth rate and optical properties of the film material was studied. Crystallization, texture development and surface roughening were demonstrated to result in a noticeable growth rate increase with increasing film thickness. Highest surface roughness values were determined for the films deposited at 350-450 °C on all substrates used. The density of the film material increased with the concentration of crystalline phase but, within experimental uncertainty, was independent of orientation and sizes of crystallites in polycrystalline films. Refractive index increased with the material density. In addition, the refractive index values that were calculated from the transmission spectra depended on the surface roughness and crystallite sizes because the light scattering, which directly influenced the extinction coefficient, caused also a decrease of the refractive index determined in this way.     

Zirconium-assisted reaction in low temperature atomic layer deposition using Bis(ethyl-methyl-amino)silane and water

The reaction of Bis(ethyl-methyl-amino)silane (BEMAS) and water in atomic layer deposition (ALD) became possible when Zr-containing species were adsorbed on the vacant sites of the surface after a pulse and purge of BEMAS. The growth rates of the Si(Zr)O_x films were 0.8-0.9 nm/cycle in the temperature range of 185-325 °C. This phenomenon probably originates from the highly reactive hydroxyl species generated by Zr atoms. From this point of view, transition metals make reactant gas molecules to be highly activated in the ALD processes of transition metal oxides and nitrides, which might be an important factor that determines the ALD characteristics.     

Effect of crystalline structure of TiO2 substrates on initial growth of atomic layer deposited Ru thin films

Ru thin films were grown on polymorphic TiO₂ thin film substrates at 230 and 250 °C by atomic layer deposition using 2,4-(dimethylpentadienyl)(ethylcyclopentadienyl)Ru and an O₂ gas. While the Ru films grown on amorphous and rutile TiO₂ substrates showed a relatively long incubation cycle number of approximately 350 and 100 at 230 and 250 °C, respectively, the Ru films grown on anatase TiO₂ substrates exhibited a significantly shorter incubation delay which was attributed to the catalytic activity of anatase TiO₂. This difference in the incubation cycle affected the surface morphology of the Ru films on different TiO₂ substrates.     

Photoluminescence observations of hydrogen incorporation and outdiffusion in ZnO thin films

ZnO thin films were deposited with the addition of H₂ to the reaction gas using the atmospheric-pressure metal organic chemical vapor deposition method. The incorporation and outdiffusion of hydrogen in ZnO films were investigated by comparing the intensity of the hydrogen-related bound-exciton peak (I₄: 3.363 eV) in the photoluminescence spectrum. The intensity of I₄ peak was found to be the strongest in the ZnO film deposited at 680 °C with H₂ present. However, for the ZnO films prepared at the same temperature 680 °C but without H₂ present and at the higher temperature of 900 °C with H₂ present, respectively, the I₄ peak was just a minor shoulder of another bound-exciton peak (I₈: 3.359 eV). The intensity of I₄ peak in the ZnO films deposited with H₂ present was found to decrease with the increasing of annealing temperature. These results suggest that it is difficult for hydrogen to incorporate into ZnO thin films grown at high temperatures even in the hydrogen-present ambient.     

Microstructural,dielectric and magnetic behavior of spin-deposited nanocrystalline nickel–zinc ferrite thin films for microwave applications

Nanocrystalline nickel ferrite and zinc doped nickel ferrite thin films with general composition Ni_1−xZn_xFe₂O₄; x=0.0, 0.2 and 0.5 were fabricated by the spin-deposition technique. Citrate precursor method was adopted to prepare coating solution used for film deposition. This method resulted in single phase, transparent, homogeneous and crack-free nanocrystalline ferrite thin films at annealing temperature as low as 400 °C. The substrates used for film deposition were ITO-coated 7059 glass, fused quartz and Si (1 0 0). The thickness of films was found to be in the range ∼1000–5500 Å. The surface microstructure and morphology investigated by atomic force microscopy (AFM) confirmed the grain size of nickel–zinc ferrite films to be in nanometer range indicating nanocrystalline nature of the films. Dielectric properties such as the real (∈′) and imaginary parts (∈″) of complex permittivity were measured in the X-band microwave frequency region (8–12 GHz) by employing extended cavity perturbation technique. The M–H hysteresis measurements on the films annealed at 650 °C revealed narrow hysteresis curves with H_c and M_s varying for different compositions.     

Effect of relative humidity on morphology of YBCO films prepared by CSD method

YBa₂Cu₃O_7−x (YBCO) films have been prepared on LaAlO₃ (1 0 0) substrates by chemical solution deposition using metal trifluoroacetates. The influence of relative humidity in coating circumstance on the morphology of YBCO films was examined by optical microscopy and atomic force microscopy. The crack-free YBCO film was obtained if the relative humidity in coating circumstance was lower than 30%. During the decomposition step, the influences of the water vapor partial pressure and the heating rate within the temperature range from 200 °C to 320 °C were discussed. A smooth YBCO pyrolzed film could be obtained if the suitable water vapor partial pressure and the suitable heating rate within the temperature range from 200 °C to 320 °C were chosen. Furthermore, the smooth crystallized films show a high critical current density of 3 MA/cm² at 77 K.     

Transmission electron microscopy studies of HfO2 thin films grown by chloride-based atomic layer deposition

Detailed transmission electron microscopy characterization of HfO₂ films deposited on Si(1 0 0) using atomic layer deposition has been carried out. The influence of deposition temperature has been investigated. At 226 °C, a predominantly quasi-amorphous film containing large grains of cubic HfO₂ (a₀ = 5.08 Å) was formed. Grain morphology enabled the nucleation sites to be determined. Hot stage microscopy showed that both the cubic phase and the quasi-amorphous phase were very resistant to thermal modification up to 500 °C. These observations suggest that nucleation sites for the growth of the crystalline cubic phase form at the growing surface of the film, rather homogeneously within the film. The films grown at higher temperatures (300-750 °C) are crystalline and monoclinic. The principal effects of deposition temperature were on: grain size, which coarsens at the highest temperature; roughness with increases at the higher temperatures due to the prismatic faceting, and texture, with texturing being strongest at intermediate temperatures. Detailed interfacial characterization shows that interfacial layers of SiO₂ form at low and high temperatures. However, at intermediate temperatures, interfaces devoid of SiO₂ were formed.     

Growth of oxide thin films for optical gas sensor applications

Tungsten trioxide and titanium dioxide thin films were synthesised by pulsed laser deposition. We used for irradiations of oxide targets an UV KrF* (λ = 248 nm, τ_FWHM ≅ 20 ns, ν = 2 Hz) excimer laser source, at 2 J/cm² incident fluence value. The experiments were performed in low oxygen pressure. The (0 0 1) SiO₂ substrates were heated during the thin film deposition process at temperature values within the 300-500 °C range. The structure and crystalline status of the obtained oxide thin films were investigated by high resolution transmission electron microscopy. Our analyses show that the films are composed by nanoparticles with average diameters from a few to a few tens of nm. Moreover, the films deposited at substrate temperatures higher than 300 °C are crystalline. The tungsten trioxide films consist of a mixture of triclinic and monoclinic phases, while the titanium dioxide films structure corresponds to the tetragonal anatase phase. The oxide films average transmittance in the visible-infrared spectral range is higher than 80%, which makes them suitable for sensor applications.     

Effect of buffer layer on VOx film fabrication by reactive RF sputtering

Vanadium oxide VO_x films were fabricated by RF magnetron sputtering on various metal buffer layers or silica glass substrates at a substrate temperature of 400 °C. V₂O₅ film was fabricated on a silica glass substrate, and VO₂ films were fabricated on V, W, Fe, Ni, Ti, and Pt metal buffer layers. The transition temperature of the sample on the V buffer layer was 68 °C and that on the W buffer layer was 53 °C. The VO₂ film was also fabricated on the V buffer layer by non-reactive sputtering using a V₂O₅ target at a substrate temperature of 400 °C.     

Electrical properties of La2O3 thin films grown on TiN/Si substrates via atomic layer deposition

The electrical as well as the structural properties of La₂O₃ thin films on TiN substrates were investigated. Amorphous stoichiometric La₂O₃ thin films were grown at 300 °C via atomic layer deposition technique by using lanthanum 2,2,6,6-tetramethyl-3,5-heptanedione [La(TMHD)₃] and H₂O as precursors. Post-annealing of the grown film induced dramatic changes in structural and the electrical properties. Crystalline phases of the La₂O₃ film emerged with the increase of the post-annealing temperature. Metal-insulator-metal (MIM) capacitor was fabricated to measure the electrical properties of the grown film. The dielectric constant of the La₂O₃ thin films increased with annealing temperature to reach the value of 17.3 at 500 °C. The leakage current density of the film post-annealed at 400 °C was estimated to be 2.78 × 10⁻¹⁰ and 2.1 × 10⁻⁸ A/cm² at ±1 V, respectively.     

Ordering temperature of L10-type FePt films reduced by CuO addition

Effects of addition of CuO layers in L1₀-type FePt thin films are investigated. The ordering temperature of L1₀-type FePt films can be reduced by CuO addition. The coercivities of 0.78 and 0.82 T are achieved in [Pt(10 Å)/Fe(14 Å)/CuO(2 Å)]₁₀ film annealed at 550 °C for 20 min and [Pt(10 Å)/Fe(15 Å)/CuO(3 Å)]₁₀ film annealed at 600 °C for 20 min, respectively, and these values are compared to the coercivity of 0.8 T in [Pt(10 Å)/Fe(13 Å)]₁₀ film annealed at 650 °C. The thickness of Fe and CuO layers strongly influences the ordering temperature of L1₀-type FePt and the magnetic properties of the films. The addition of CuO not only brings microstructure and surface morphology changes of FePt film, but also lowers the ordering temperature.     

Influence of heat treatment on the structure and magnetic properties of the Co/Zr and Co/Hf multilayer amorphous films

The influence of annealing on the structure and magnetic properties of amorphous Co/Zr and Co/Hf multilayer films was studied with particular attention to the dependence of the magnetic properties, thermal stability and crystallization process on layer composition and thickness. The temperature at which crystallization commences increases from 400 to 460 °C as the layer thickness d_Zr or d_Hf increases from 6 to 18 Å, and decreases from 450 to 400 °C as d_Co increases from 12 to 18 Å. Multilayers containing 19–60 at% Zr were studied. The specific magnetization was found to increase even below the temperature at which crystallization commences. Our data are compared with non-multilayer Co–Zr amorphous films and rapidly quenched metallic glasses.     

Influence of substrate temperature on structures and dielectric properties of pyrochlore Bi1.5Zn1.0Nb1.5O7 thin films prepared by pulsed laser deposition

The influence of substrate temperature on structural and dielectric properties of cubic pyrochlore Bi_1.5Zn_1.0Nb_1.5O₇ (BZN) thin films prepared by pulsed laser deposition process has been investigated. BZN thin films were deposited on Pt/Ti/SiO₂/Si(1 0 0) substrate and in situ annealed at 700 °C. The results indicate that the substrate temperature has a significant effect on the structural and dielectric properties of BZN thin films. The films exhibit a cubic pyrochlore structure in the substrate temperature range from 550 °C to 700 °C and at the annealing temperature of 700 °C. With further increase of substrate temperature to 750 °C, the phases of Bi₂O₃, BiNbO₄ and Bi₅Nb₃O₁₅ can be detected in the XRD pattern due to the Zn loss. The dielectric constant and loss tangent of the films deposited at 650 °C are 192 and 6 × 10⁻⁴ at 10 kHz, respectively. The tunability is 10% at a dc bias field of 0.9 MV/cm.     

Effect of composition and deposition temperature on the characteristics of Ga doped ZnO thin films

ZnO films doped with Ga (GZO) of varying composition were prepared on Corning glass substrate by radio frequency magnetron sputtering at various deposition temperatures of room temperature, 150, 250 and 400 °C, and their temperature dependent photoelectric and structural properties were correlated with Ga composition. With increasing deposition temperature, the Ga content, at which the lowest electrical resistivity and the best crystallinity were observed, decreased. Films with optimal electrical resistivity of 2-3 × 10⁻⁴ Ω cm and with good crystallinity were obtained in the substrate temperature range from 150 to 250 °C, and the corresponding C_Ga/(C_Ga + C_Zn) atomic ratio was about 0.049. GZO films grown at room temperature had coarse columnar structure and low optical transmittance, while films deposited at 400 °C yielded the highest figure of merit (FOM) due to very low optical absorption despite rather moderate electrical resistivity slightly higher than 4 × 10⁻⁴ Ω cm. The optimum Ga content at which the maximum figure of merit was obtained decreased with increasing deposition temperature.     

Effect of deposition temperature on orientation and electrical properties of (K0.5Na0.5)NbO3 thin films by pulsed laser deposition

Lead-free ferroelectric K_0.5Na_0.5NbO₃ (KNN) thin films have been prepared on Pt/TiO₂/SiO₂/Si substrates by pulsed laser deposition process. The structures, crystal orientations and electrical properties of thin films have been investigated as a function of deposition temperature from 680 °C to 760 °C. It is found that the deposition temperature plays an important role in the structures, crystal orientations and electrical properties of thin films. The crystallization of thin films improves with increasing deposition temperature. The thin film deposited at 760 °C exhibits strong (0 0 1) preferential orientation, large dielectric constant of 930 and the remnant polarization of 8.54 μC/cm².     

Structural, optical and magnetic properties of (ZnO)1−x(MnO2)x thin films deposited at room temperature

The structural, magnetic and optical properties of (ZnO)_1−x(MnO₂)_x (with x = 0.03 and 0.05) thin films deposited by pulsed laser deposition (PLD) were studied. The pellets used as target, sintered at different temperatures ranging from 500 °C to 900 °C, were prepared by conventional solid state method using ZnO and MnO₂ powders. The observation of non-monotonic shift in peak position of most preferred (1 0 1) ZnO diffraction plane in XRD spectra of pellets confirmed the substitution of Mn ions in ZnO lattice of the sintered targets. The as-deposited thin film samples are found to be polycrystalline with the preferred orientation mostly along (1 1 0) diffraction plane. The UV-vis spectroscopy of the thin films revealed that the energy band gap exhibit blue shift with increasing Mn content which could be attributed to Burstein-Moss shift caused by Mn doping of the ZnO. The deposited thin films exhibit room temperature ferromagnetism having effective magnetic moment per Mn atom in the range of 0.9-1.4μ_B for both compositions.     

Properties of AlN grown by plasma enhanced atomic layer deposition

The influence of growth parameters on the properties of AlN films fabricated by plasma-enhanced atomic layer deposition using trimethylaluminum and ammonia precursors was investigated. The atomic concentrations, refractive index, mass density, crystallinity and surface roughness were studied from the films grown in the temperature range of 100-300 °C with plasma discharge times between 2.5 and 30 s. The AlN films were shown to be hydrogen rich having H concentrations in the range of 13-27 at.% with inverse dependence on the growth temperature. The carbon and oxygen concentrations in the films were less than 2.6% and 0.2%, respectively. The refractive index and mass density of the films correlated with the hydrogen concentration so that higher concentrations (lower growth temperatures) resulted in smaller refractive index and mass density. The film grown at 300 °C was found to be crystalline whereas lower growth temperature produced amorphous films.     

Optical properties of ITO/TiO2 single and double layer thin films deposited by RPLAD

Indium tin oxide (ITO) and titanium dioxide (TiO₂) single layer and double layer ITO/TiO₂ films were prepared using reactive pulsed laser ablation deposition (RPLAD) with an ArF excimer laser for applications in dye-sensitized solar cells (DSSCs). The films were deposited on SiO₂ substrates either at room temperatures (RT) or heated to 200-400 °C. Under optimized conditions, transmission of ITO films in the visible (vis) range was above 89% for films produced at RT and 93% for the ones deposited at higher temperatures. Increasing the substrate temperature from RT to 400 °C enhances the transmission of TiO₂ films in the vis-NIR from about 70% to 92%. High transmission (≈90%) was observed for the double layer ITO/TiO₂ with a transmission cut-off above 900 nm. From the transmission data, the energies gaps (E_g), as well as the refractive indexes (n) for the films were estimated. n ≈ 2.03 and 2.04, respectively for ITO films and TiO₂ film deposited at 400 °C in the visible region. Post-annealing of the TiO₂ films for 3 h at 300 and 500 °C was performed to enhance n. The refractive index of the TiO₂ films increases with the post-annealing temperature. The direct band gap is 3.6, 3.74 and 3.82 eV for ITO films deposited at RT, 200, and 400 °C, respectively. The TiO₂ films present a direct band gap of 3.51 and 3.37 eV for as deposited TiO₂ films and when annealed at 400 °C, respectively. There is a shift of about 0.1 eV between ITO and ITO/TiO₂ films deposited at 200 °C. The shift decreases by half when the TiO₂ film was deposited at 400 °C. Post-annealing was also performed on double layer ITO/TiO₂.