Study of the structure and electrical properties of the copper nitride thin films deposited by pulsed laser deposition

Copper nitride thin films were prepared on glass and silicon substrates by ablating a copper target at different pressure of nitrogen. The films were characterized in situ by X-ray photoelectron spectroscopy (XPS), Auger electron spectroscopy (AES) and ex situ by X-ray diffraction (XRD). The nitrogen content in the samples, x = [N]/[Cu], changed between 0 and 0.33 for a corresponding variation in nitrogen pressure of 9 × 10⁻² to 1.3 × 10⁻¹ Torr. Using this methodology, it is possible to achieve sub-, over- and stoichiometric films by controlling the nitrogen pressure. The XPS results show that is possible to obtain copper nitride with x = 0.33 (Cu₃N) and x = 0.25 (Cu₄N) when the nitrogen pressure is 1.3 × 10⁻¹ and 5 × 10⁻² Torr, respectively. The lattice constants obtained from XRD results for copper nitride with x = 0.25 is of 3.850 Å and with x = 0.33 have values between 3.810 and 3.830 Å. The electrical properties of the films were studied as a function of the lattice constant. These results show that the electrical resistivity increases when the lattice parameter is decreasing. The electrical resistivity of copper nitride with x = 0.25 was smaller than samples with x = 0.33.     

Characterization of polymer thin films obtained by pulsed laser deposition

The development of laser techniques for the deposition of polymer and biomaterial thin films on solid surfaces in a controlled manner has attracted great attention during the last few years. Here we report the deposition of thin polymer films, namely Polyepichlorhydrin by pulsed laser deposition. Polyepichlorhydrin polymer was deposited on flat substrate (i.e. silicon) using an NdYAG laser (266 nm, 5 ns pulse duration and 10 Hz repetition rate).The obtained thin films have been characterized by atomic force microscopy, scanning electron microscopy, Fourier transform infrared spectroscopy and spectroscopic ellipsometry.It was found that for laser fluences up to 1.5 J/cm² the chemical structure of the deposited polyepichlorhydrin polymer thin layers resembles to the native polymer, whilst by increasing the laser fluence above 1.5 J/cm² the polyepichlorohydrin films present deviations from the bulk polymer.Morphological investigations (atomic force microscopy and scanning electron microscopy) reveal continuous polyepichlorhydrin thin films for a relatively narrow range of fluences (1-1.5 J/cm²).The wavelength dependence of the refractive index and extinction coefficient was determined by ellipsometry studies which lead to new insights about the material.The obtained results indicate that pulsed laser deposition method is potentially useful for the fabrication of polymer thin films to be used in applications including electronics, microsensor or bioengineering industries.     

Optical and structural properties of pulsed laser ablation deposited ZnO thin film

A limited number of reports exists in the literature concerning the systematic study of the structural and optical properties of ZnO thin films, produced by pulsed laser ablation, in correlation with the deposition parameters adopted. In this paper we present a characterization of a sample prepared by this technique and studied by photoelectron spectroscopy and X-ray diffraction. The dielectric function of both target and films has been deduced by reflection electron energy loss spectroscopy.     

Crystallization and grain growth characteristics of yttria-stabilized zirconia thin films grown by pulsed laser deposition

Knowledge about the crystallization and grain growth characteristics of metal oxide thin films is essential for effective microstructural engineering by thermal post-annealing and the integration to Si-based miniaturized electroceramic devices. Finite size and interface effects may cause fundamentally different behavior compared to three dimensional macroscopic systems. This work presents a comprehensive investigation of the crystallization kinetics and microstructural evolution upon thermal post-annealing of amorphous 200 nm and 1.2 μm thin films of 8 mol% yttria-stabilized zirconia grown by pulsed laser deposition (PLD) using ex- and in-situ X-ray diffraction, Raman spectroscopy, and electron microscopy techniques. The layers exhibit a remarkably low crystallization temperature of 200-250 °C while exposure to energetic electrons induces the formation of randomly dispersed ~ 20 nm sized crystallites already at ambient temperature. The isothermal amorphous to crystalline phase transformation kinetics can be described quantitatively by the Johnson-Mehl-Avrami-Kolmogorov model. They reveal characteristics of a three dimensional growth under cation bulk diffusion control with heterogeneous nucleation that changes from continuous to instantaneous initial seeding at temperatures above 300 °C. Large (> 100 nm) equiaxed grains are formed rapidly without a stabilization of transient nanocrystals during the thermally induced phase transformation. A stagnation of normal grain growth resulting in a logarithmic normal size distribution is observed once the average grain dimensions approach the film thickness. The results on the crystallization and grain growth of the PLD-grown YSZ films are evaluated with regards to the fabrication of YSZ solid electrolyte membranes for Si-supported micro solid oxide fuel cells and gas sensors.     

Role of vanadium content in ZnO thin films grown by pulsed laser deposition

Vanadium-doped ZnO films (Zn_1−xV_xO, where x = 0.02, 0.03, 0.05 and 0.07), were formed from ceramic targets on c-cut sapphire substrates using pulsed laser deposition at substrate temperature of 600 °C and oxygen pressure of 10 Pa. In order to clarify how the vanadium concentration influences the films’ properties, structural and magnetic investigations were performed. All films crystallised in wurtzite phase and presented a c-axis preferred orientation at low concentrations of vanadium. The results implied that the doping concentration and crystalline microstructure influence strongly the system's magnetic characteristics. Weak ferromagnetism was registered for the film with the lowest doping concentration (2 at.%), which exhibited a ferromagnetic behavior at Curie temperature higher than 300 K. Increasing the vanadium content in the film caused degradation of the magnetic ordering.     

Properties of Dy-doped ZnO nanocrystalline thin films prepared by pulsed laser deposition

Highly transparent conductive Dy₂O₃ doped zinc oxide (ZnO)_1-x(Dy₂O₃)_x nanocrystalline thin films with x from 0.5% to 5% have been deposited on glass substrate by pulsed laser deposition technique. The structural, electrical and optical properties of Dy₂O₃ doped thin films were investigated as a function of the x value. The experimental results show that the Dy concentration in Dy-doped ZnO thin films has a strong influence on the material properties especially electrical properties. The resistivity decreased to a minimum value of 5.02 × 10⁻⁴ Ω cm with x increasing from 0.5% to 1.0%, then significantly increased with the further increasing of x value. On the contrary, the optical direct band gap of the (ZnO)_1-x(Dy₂O₃)_x films first increased, then decreased with x increasing. The average transmission of Dy₂O₃ doped zinc oxide films in the visible range is above 90%.     

Characterization of pulsed laser deposited chalcogenide thin layers

In this work we report on pulsed laser deposition (PLD) of chalcogenide thin films from the systems (AsSe)_100−xAgI_x and (AsSe)_100−xAg_x for sensing applications. A KrF* excimer laser (λ = 248 nm; τ_FWHM = 25 ns) was used to ablate the targets that had been prepared from the synthesised chalcogenide materials. The films were deposited in either vacuum (4 × 10⁻⁴ Pa) or argon (5 Pa) on silicon and glass substrates kept at room temperature. The basic properties of the films, including their morphology, topography, structure, and composition were characterised by complementary techniques. Investigations by X-ray diffraction (XRD) confirmed the amorphous nature of the films, as no strong diffraction reflections were found. The film composition was studied by energy dispersive X-ray (EDX) spectroscopy. The morphology of the films investigated by scanning electron microscopy (SEM), revealed a particulate-covered homogeneous surface, typical of PLD. Topographical analyses by atomic force microscopy (AFM) showed that the particulate size was slightly larger in Ar than in vacuum. The uniform surface areas were rather smooth, with root mean square (rms) roughness increasing up to several nanometers with the AgI or Ag doping. Based upon the results from the comprehensive investigation of the basic properties of the chalcogenide films prepared by PLD and their dependence on the process parameters, samples with appropriate sorption properties can be selected for possible applications in cantilever gas sensors.     

Structural and optical properties of ZnO thin films deposited on quartz glass by pulsed laser deposition

ZnO thin films with typical c-axis (0 0 2) orientation were successfully deposited on quartz glass substrates by pulse laser ablation of Zn target in oxygen atmosphere at a relatively low temperature range of 100-250 °C. The structural and optical properties of the films were studied. In photoluminescence (PL) spectra at room temperature, single ultraviolet emission (without deep-level emission) was obtained from ZnO film deposited at the temperature of 200 °C. This was attributed to its low intrinsic defects.     

Effect of annealing on thermal stability and morphology of pulsed laser deposited Ir thin films

Iridium (Ir) thin films, deposited on Si (1 0 0) substrate by pulsed laser deposition (PLD) technique using Ir target in a vacuum atmosphere, were annealed in air ambient and the thermal stability was investigated. The crystal structure and surface morphology of Ir thin films before and after being annealed were studied by X-ray diffraction, Raman scattering, scanning electron microscope, and atomic force microscopy. The results showed that single-phase Ir thin films with (1 1 1) preferred orientation could be deposited on Si (1 0 0) substrate at 300 °C and it remained stable below 600 °C, which showed a promising bottom electrode of integrated ferroelectric capacitors. Ir thin films got oxidized to IrO₂ at temperatures from 650 to 800 °C.     

Effect of oxygen partial pressure on PLD cobalt oxide films

Thin CoO oxide layers with superior properties in terms of crystallographic ordering, surface roughness and constant and controlled chemical compositions have been prepared by pulsed laser deposition in reactive O₂ atmosphere at 400 °C. Such systems are particularly suitable both for applications and for basic studies, any time high quality and controlled surfaces are required, for example in multilayered systems whose behaviour critically depends on interface properties, such as magnetically exchange-coupled systems. A structural and microstructural study of such films is presented, together with the compositional analysis for different process conditions. The best control on film stoichiometry was obtained by protecting the surface with a thin Pt cap-layer, before air exposure.     

Influence of substrate temperature and post-treatment on the properties of ZnO:Al thin films prepared by pulsed laser deposition

Highly transparent conductive Al₂O₃ doped zinc oxide (AZO) thin films have been deposited on the glass substrate by pulsed laser deposition technique. The effects of substrate temperature and post-deposition annealing treatment on structural, electrical and optical properties of AZO thin films were investigated. The experimental results show that the electrical resistivity of films deposited at 240 °C is 6.1 × 10⁻⁴ Ω cm, which can be further reduced to as low as 4.7 × 10⁻⁴ Ω cm by post-deposition annealing at 400 °C for 2 h in argon. The average transmission of AZO films in the visible range is 90%. The optical direct band gap of films was dependent on the substrate temperature and the annealing treatment in argon. The optical direct band gap value of AZO films increased with increasing annealing temperature.     

Morphological and optical properties of silicon thin films by PLD

Silicon thin films have been prepared on sapphire substrates by pulsed laser deposition (PLD) technique. The films were deposited in vacuum from a silicon target at a base pressure of 10⁻⁶ mbar in the temperature range from 400 to 800 °C. A Q-switched Nd:YAG laser (1064 nm, 5 ns duration, 10 Hz) at a constant energy density of 2 J × cm⁻² has been used. The influence of the substrate temperature on the structural, morphological and optical properties of the Si thin films was investigated.Spectral ellipsometry and atomic force microscopy (AFM) were used to study the thickness and the surface roughness of the deposited films. Surface roughness values measured by AFM and ellipsometry show the same tendency of increasing roughness with increased deposition temperature.     

Effects of deposition temperature on the structural and morphological properties of thin ZnO films fabricated by pulsed laser deposition

ZnO thin films were grown on Si(1 0 0) substrates using pulsed laser deposition in O₂ gas ambient (10 Pa) and at different substrate temperatures (25, 150, 300 and 400 °C). The influence of the substrate temperature on the structural and morphological properties of the films was investigated using XRD, AFM and SEM. At substrate temperature of T=150 °C, a good quality ZnO film was fabricated that exhibits an average grain size of 15.1 nm with an average RMS roughness of 3.4 nm. The refractive index and the thickness of the thin films determined by the ellipsometry data are also presented and discussed.     

Pulsed laser deposition of fluoride glass thin films

The development of integrated waveguide lasers for different applications such as marking, illumination or medical technology has become highly desirable. Diode pumped planar waveguide lasers emitting in the green visible spectral range, e.g. thin films from praseodymium doped fluorozirconate glass matrix (called ZBLAN, owing to the main components ZrF₄, BaF₂, LaF₃, AlF₃ and NaF) as the active material pumped by a blue laser diode, have aroused great interest. In this work we have investigated the deposition of Pr:ZBLAN thin films using pulsed laser radiation of λ = 193 and λ = 248 nm. The deposition has been carried out on MgF₂ single crystal substrates in a vacuum chamber by varying both processing gas pressure and energy fluence. The existence of an absorption line at 210 nm in Pr:ZBLAN leads to absorption and radiative relaxation of the absorbed laser energy of λ = 193 nm preventing the evaporation of target material. The deposited thin films consist of solidified and molten droplets and irregular particulates only. Furthermore, X-ray radiation has been applied to fluoride glass targets to enhance the absorption in the UV spectral region and to investigate the deposition of X-ray treated targets applying laser radiation of λ = 248 nm. It has been shown that induced F-centres near the target surface are not thermally stable and can be easily ablated. Therefore, λ = 248 nm is not suitable for evaporation of Pr:ZBLAN.     

Deposition of zinc oxide thin films by reactive pulsed laser ablation

Thin films of zinc oxide have been deposited by reactive pulsed laser ablation of Zn and ZnO targets in presence of a radio frequency (RF) generated oxygen plasma. The gaseous species have been deposited at several substrate temperatures, using the on-axis configuration, on Si (1 0 0). Thin films have been characterized by scanning electron microscopy, atomic force microscopy, X-ray diffraction, X-ray photoelectron spectroscopy and infrared spectroscopy. A comparison among conventional PLD and reactive RF plasma-assisted PLD has been performed.     

In situ grown epitaxial YBa2Cu3O7 − x thin films by pulsed laser deposition under reduced oxygen pressure during cool-down time

We report novel pulsed laser deposition conditions that were used to obtain superconducting epitaxial YBCO thin films, grown in situ using an oxygen pressure lower than the usual one during the cool-down time. We studied the influence of the PLD conditions as substrate temperature, oxygen pressure, laser fluence, and number of laser pulses on the crystallographic and morphological features, and on the superconducting properties of the films. Good superconducting properties were obtained without a high temperature post-deposition annealing process. A maximum critical temperature of 88.6 K was obtained.     

Non-stoichiometry-induced metal-to-insulator transition in nickelate thin films grown by pulsed laser deposition

While controlling the cation contents in perovskite rare-earth nickelate thin films, a metal-to-insulator phase transition is reported. Systematic control of cation stoichiometry has been achieved by manipulating the irradiation of excimer laser in pulsed laser deposition. Two rare-earth nickelate bilayer thin-film heterostructures with the controlled cation stoichiometry (i.e. stoichiometric and Ni-excessive) have been fabricated. It is found that the Ni-excessive nickelate film is structurally less dense than the stoichiometric film, albeit both of them are epitaxial and coherent with respect to the underlying substrate. More interestingly, as a temperature decreases, a metal-to-insulator transition is only observed in the Ni-excessive nickelate films, which can be associated with the enhanced disproportionation of the Ni charge valence. Based on our theoretical results, possible origins (e.g. anti-site defects) of the low-temperature insulating state are discussed with the need of future work for deeper understanding. Our work can be utilized to realize unusual physical phenomena (e.g. metal-to-insulator phase transitions) in complex oxide films by manipulating the chemical stoichiometry in pulsed laser deposition.     

Pulsed laser deposition and its current research status in preparing hydroxyapatite thin films

Pulsed laser deposition (PLD) is a conceptually and experimentally simple yet highly versatile tool for thin films and multi-layer film research. The mechanisms, advantages and disadvantages of pulsed laser deposition were reviewed. The process and some methods to resolve the drawbacks of PLD were discussed. Pulsed laser deposition of hydroxyapatite thin films was reviewed. Simple adjustment of PLD parameters can deposit hydroxyapatite in situ in crystalline form, amorphous films or HA with other calcium phosphate phases. Compared with plasma sprayed HA coatings the pulsed laser deposition HA thin films have higher coating/substrate adhesion and have minor undesirable phases under optimal conditions. Finally, we suggested some new researches should be done.     

Structural and morphological properties of thin ZnO films grown by pulsed laser deposition

The pulsed laser deposition technique was used to produce zinc oxide thin films onto silicon and Corning glass substrates. Homogeneous surfaces exhibiting quite small Root Mean Square (RMS) roughness, consisting of shaped grains were obtained, their grain diameters being 40-90 nm at room temperature and at 650 °C growth respectively. Films were polycrystalline, even for growth at room temperature, with preferential crystallite orientation the (0 0 2) basal plane of wurtzite ZnO. Temperature increase caused evolution from grain to grain agglomeration structures, improving crystallinity. Compressive to tensile stresses transition with temperature was found while the lattice constant decreased.