Wear resistance of reactive plasma sprayed and laser remelted TiB2-TiC0.3N0.7 based composite coatings against medium carbon steel

Wear resistance of reactive plasma sprayed TiB₂-TiC_0.3N_0.7 based composite coatings and the as-sprayed coating with laser surface treatment was investigated using plate-on-plate tests. Wear tests were performed at different normal loads and sliding speeds under dry sliding conditions in air. The surface morphologies of counterparts against as-sprayed and laser remelted coatings were investigated. The microstructure and chemical composition of wear debris and coatings were studied using scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDS), respectively. The results show that the wear resistance of the laser remelted coating is improved significantly due to their increased microhardness and reduced flaws. The primary wear mechanism of the remelted coating is oxidation wear and its minor wear mechanisms are grain abrasion and fatigue failure during the course of wear test. In contrast, the primary wear mechanism of the as-sprayed coating is grain abrasion at the low sliding speed (370 rpm) and fatigue failure at the high sliding speed (549 rpm). The oxidation wear mechanism is a minor contributor for the as-sprayed coating.     

Suspension plasma sprayed composite coating using amorphous powder feedstock

Al₂O₃-ZrO₂ composite coatings were deposited by the suspension plasma spray process using molecularly mixed amorphous powders. X-ray diffraction (XRD) analysis shows that the as-sprayed coating is composed of α-Al₂O₃ and tetragonal ZrO₂ phases with grain sizes of 26 nm and 18 nm, respectively. The as-sprayed coating has 93% density with a hardness of 9.9 GPa. Heat treatment of the as-sprayed coating reveals that the Al₂O₃ and ZrO₂ phases are homogeneously distributed in the composite coating.     

Preparation and characterization of nickel nano-Al2O3 composite coatings by sediment co-deposition

Ni-Al₂O₃ composite coatings were prepared by using sediment co-deposition (SCD) technique and conventional electroplating (CEP) technique from Watt's type electrolyte without any additives. The microstructure, hardness, and wear resistance of resulting composites were investigated. The results show that the incorporation of nano-Al₂O₃ particles changes the surface morphology of nickel matrix. The preferential orientation is modified from (2 0 0) plane to (1 1 1) plane. The microhardness of Ni-Al₂O₃ composite coatings in the SCD technique are higher than that of the CEP technique and pure Ni coating and increase with the increasing of the nano-Al₂O₃ particles concentration in plating solution. The wear rate of the Ni-Al₂O₃ composite coating fabricated via SCD technique with 10 g/l nano-Al₂O₃ particles in plating bath is approximately one order of magnitude lower than that of pure Ni coating. Wear resistance for SCD obtained composite coatings is superior to that obtained by the CEP technique. The wear mechanism of pure Ni and nickel nano-Al₂O₃ composite coatings are adhesive wear and abrasive wear, respectively.     

Electrodeposition and characterization of Ni-Y2O3 composite

Nano-sized Y₂O₃ particles were codeposited with nickel by electrolytic plating from a nickel sulfate bath. The effects of the incorporated Y₂O₃ on the structure, morphology and mechanical properties (including microhardness, friction coefficient and wear resistant) of Ni-Y₂O₃ composite coatings were studied. It is observed that the addition of nano-sized Y₂O₃ particles shows apparent influence on the reduction potential and pH of the electrolyte. The incorporated Y₂O₃ increases from 1.56 wt.% to 4.4 wt.% by increasing the Y₂O₃ concentration in the plating bath from 20 to 80 g/l. XRD results reveal that the incorporated Y₂O₃ particles favour the crystal faces (2 0 0) and (2 2 0). SEM and AFM images demonstrate that the addition of Y₂O₃ particles causes a smooth and compact surface. The present study also shows that the codeposited Y₂O₃ particles in deposits decrease the friction coefficient and simultaneously reduce the wear weight loss. Ni-Y₂O₃ composite coatings reach their best microhardness and tribological properties at Y₂O₃ content 4.4 wt.% under the experiment conditions.     

SHS等离子喷涂制备FeAl2O4-Al2O3-Fe纳米复合涂层的研究

利用SHS等离子喷涂技术，将经过机械团聚法制备的Fe₂O₃-Al复合粉体送入等离子焰流，沉积出厚度约为400 μm的复合涂层.利用XRD，SEM 和TEM等检测手段对涂层的成分和组织进行了分析，测定了涂层的显微硬度、断裂韧性以及耐磨性.结果表明涂层为具有纳米结构的FeAl₂O₄-Al₂O₃-Fe纳米复合组织；涂层的显微硬度为HV_100g870；断裂韧性是普通Al₂O₃涂层的2倍；无润滑磨损的耐磨性是普通Al₂O₃涂层的2.5倍. 关键词： SHS等离子喷涂 纳米涂层 断裂韧性     

电解等离子体法制备Al2O3陶瓷层及其特性研究

利用电弧喷铝并重熔后进行电解等离子体处理(EPP)的方法在Q235钢基体上制备出呈冶金结 合的Al₂O₃陶瓷层.利用XRD，SEM和EDS等手段对陶瓷层的成分和显 微组织进行了分析， 测定了陶瓷层的耐蚀性能和耐磨性能.实验结果表明，陶瓷层主要由α-Al₂O3，γ-Al₂O₃，θ-Al₂O₃以及一 些非晶相组成，组织致密，耐蚀性能和耐磨性能良好. 关键词： 电解等离子体处理 陶瓷层 复合技术 生长机理     

Influence of long-term aqueous exposure on surface properties of plasma sprayed oxides Al2O3, TiO2 and their mixture Al2O3-13TiO2

The surface properties of plasma sprayed Al₂O₃- and TiO₂-based coating materials were characterized in order to investigate the influence of surface strain and phase inhomogenity. The materials were water exposed up to 8 months. The bulk crystallographic structure, dissolution behaviour, effective charge (zeta potential, isoelectric point), surface compositions and oxidation states were determined. In addition, the properties of the aging solutions, such as conductivity, supernatant pH (point of zero charge), and redox potential, were monitored during aging.It was shown that the materials were stable under aging conditions, but that considerable surface rearrangements, such as dissolution-reprecipitation and surface site redistributions may occur. However, overall only minor changes in surface properties results from this restructuring process.     

Influence of treating frequency on microstructure and properties of Al2O3 coating on 304 stainless steel by cathodic plasma electrolytic deposition

Alumina ceramic coatings were fabricated on 304 stainless steel by cathodic plasma electrolytic deposition (CPED). Influence of treating frequency of the power supply on the microstructure and properties of the coatings were studied. The results indicated that coatings obtained at various frequencies on 304 stainless steels were all composed of α-Al₂O₃ and γ-Al₂O₃, and α-Al₂O₃ was the dominant phase. The contents of α-Al₂O₃ decreased gradually in a very small rate with increasing the frequency and γ-Al₂O₃ gradually increased. The surface of alumina ceramic coating was porous. With increasing the frequency, the coating surface gradually became less rough and more compact, resulting in low surface roughness. The bonding strength of Al₂O₃ coating was higher than 22 MPa and was not strongly affected by treating frequency. With increasing the frequency, the alumina coated steels showed better and gradually increasing corrosion resistance than the uncoated one in 3.5% NaCl solution. The coating steel with desirable corrosion resistance was obtained at 800 Hz whose corrosion current potential and corrosion density were −0.237 V and 7.367 × 10⁻⁸ A/cm², respectively.     

Parametric study of Al and Al2O3 ceramic coatings deposited by air plasma spray onto polymer substrate

Aluminum and ceramic (Al₂O₃) coatings were deposited onto the polymer substrate by air plasma spray (APS) to improve the mechanical properties of the polymer surface. The effect of spray parameters (current and spray distance in this paper) on the phase composition, microstructure and mechanical properties was investigated. Shear adhesion strength between the coatings and the substrates was also examined. The results indicate that the deposition parameters have a significant effect on the phase composition, microstructure and mechanical properties of as-spayed coatings. The maximum shear adhesion strength of the bond coats was 5.21 MPa with the current of 180 A and 190 mm spray distance.     

Effect of α-Al2O3 on the properties of cold sprayed Al/α-Al2O3 composite coatings on AZ91D magnesium alloy

Composite coatings using pure Al powder blended with α-Al₂O₃ as feedstock were deposited on AZ91D magnesium alloy substrates by cold spray (CS). The content of α-Al₂O₃ in the feedstock was 25 wt.% and 50 wt.%, respectively. The effects of α-Al₂O₃ on the porosity, microhardness, adhesion and tensile strength of the coatings were studied. Electrochemical tests were carried out in neutral 3.5 wt.% NaCl solution to evaluate the effect of α-Al₂O₃ on the corrosion behavior of the coatings. The results showed that the composite coatings possessed lower porosity, higher adhesion strength and tensile strength than cold sprayed pure Al coating. The corrosion current densities of the composite coatings were similar to that of the pure Al coating and much higher than that of bare AZ91D magnesium alloy.     

Electrodeposition and properties of Zn-nanosized TiO2 composite coatings

Nanosized TiO₂ particles were prepared by sol-gel method. The TiO₂ particles were co-deposited with zinc from a sulphate bath at pH 4.5 using electrodeposition technique. The corrosion behavior of the coatings was assessed by electrochemical polarization, impedance, weight-loss and salt spray tests. Wear resistance and microhardness of the composite coating was measured. The smaller grain size of the composite coatings was observed in the presence of TiO₂ and it was confirmed by the images of scanning electron microscopy (SEM) and X-ray diffraction (XRD) techniques.     

Laser treatment of Si-Al2O3 two-layer target

The laser treatment of two-layer Si-Al₂O₃ target at λ=1064 nm and P=170 W in a N₂+O₂ atmosphere by electron microscopy, atomic force microscopy, X-ray microanalysis, and IR-spectroscopy was investigated. It is established that in the stage of fracture of a silicon plate, the ablation products were silicon clusters into which, when passing over, oxygen and nitrogen diffused. On collective plate, a SiO_xN composite film formed. In the stage of fracture of an alumina plate, the oxidation of silicon in the channel zone and the interaction of Al and Si oxides, accompanied by their nitration, occurred. In this stage, evolved oxide vapors and ejected mullite drops deposit on the SiO_xN film. On collective plate, mullite nanowhiskers grew from mullite drops by the vapor-liquid-solid body mechanism.     

Temperature-induced changes in morphology and structure of TiO2-Al2O3 fibers

Electrospinning of a sol-gel and polymer mixture is used to produce titania-alumina (TiO₂-Al₂O₃) fibers with diameters ranging from 200 to 800 nm. These composite metal-oxide fibers were calcined at various temperatures and their morphology is studied using scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The decrease in the average diameter of the fibers with increasing temperature is observed. Powder X-ray diffraction (XRD) reveals that up to 800 °C the composite fibers have anatase titania structure whereas at 900 °C the fibers exhibit mixture of anatase and rutile phases. It is found that specific surface area decreases as a function of temperature in the 700-900 °C range. The change in phase (anatase-to-rutile) and the increase in crystallite size occur simultaneously. The presence of smaller amount of amorphous alumina in the primarily titania-based structure seems to play the role in stabilizing the anatase phase.     

Silane treatment of Fe3O4 and its effect on the magnetic and wear properties of Fe3O4/epoxy nanocomposites

In this study, the effect of silane treatment of Fe₃O₄ on the magnetic and wear properties of Fe₃O₄/epoxy nanocomposites was investigated. Fe₃O₄ nanopowders were prepared by coprecipitation of iron(II) chloride tetrahydrate with iron(III) chloride hexahydrate, and the surfaces of Fe₃O₄ were modified with 3-aminopropyltriethoxysilane. The magnetic properties of the powders were measured on unmodified and surface-modified Fe₃O₄/epoxy nanocomposites using SQUID magnetometer. Wear tests were performed on unmodified and surface-modified Fe₃O₄/epoxy nanocomposites under the same conditions (sliding speed: 0.18 m/s, load: 20 N).The results showed that the saturation magnetization (M_s) of surface-modified Fe₃O₄/epoxy nanocomposites was approximately 110% greater than that of unmodified Fe₃O₄/epoxy nanocomposites. This showed that the specific wear rate of surface-modified Fe₃O₄/epoxy nanocomposites was lower than that of unmodified Fe₃O₄/epoxy nanocomposites. The decrease in wear rate and the increase in magnetic properties of surface-modified Fe₃O₄/epoxy nanocomposites occurred due to the improved dispersion of Fe₃O₄ into the epoxy matrix.     

激光重熔对等离子喷涂ZrO2-20%Y2O3热障涂层隔热性能的影响

采用大气等离子喷涂（APS）技术在铝基体表面制备氧化锆（ZrO2-20%Y2O3,质量分数）热障涂层,并用脉冲激光对其进行重熔处理,研究了激光重熔对涂层组织形貌、物相转变和隔热性能的影响。研究结果表明激光的比能量对涂层的成型及性能有重要影响,过高的比能量会使涂层表面粗糙度增加,涂层成型变差。在选用合适的低比能量激光重熔条件下,扫描电镜观察结果表明经激光重熔可消除喷涂态涂层的孔隙和层状结构。对粉末和重熔前后的涂层进行了X射线衍射分析,结果表明喷涂及重熔过程中都没有发生相变;隔热试验结果表明重熔后涂层的隔热温度有所下降。     

激光重熔对等离子喷涂ZrO_2-20%Y_2O_3热障涂层隔热性能的影响

采用大气等离子喷涂(APS)技术在铝基体表面制备氧化锆(ZrO2-20%Y2O3,质量分数)热障涂层,并用脉冲激光对其进行重熔处理,研究了激光重熔对涂层组织形貌、物相转变和隔热性能的影响。研究结果表明激光的比能量对涂层的成型及性能有重要影响,过高的比能量会使涂层表面粗糙度增加,涂层成型变差。在选用合适的低比能量激光重熔条件下,扫描电镜观察结果表明经激光重熔可消除喷涂态涂层的孔隙和层状结构。对粉末和重熔前后的涂层进行了X射线衍射分析,结果表明喷涂及重熔过程中都没有发生相变;隔热试验结果表明重熔后涂层的隔热温度有所下降。     

Microstructures and properties of plasma sprayed FeAl/CeO2/ZrO2 nano-composite coating

Commercial FeAl powders and ZrO₂ nano-particles as well as CeO₂ additive were reconstituted into a novel multi-compositional feedstock powders via spray drying. The resulting feedstock powders were used to deposit FeAl/CeO₂/ZrO₂ nano-composite coating by plasma spraying on 1Cr18Ni9Ti stainless steel. An X-ray diffractometer (XRD), a scanning electron microscope equipped with an energy dispersive spectrometer (SEM/EDS), and a field emission scanning electron microscope equipped with an energy dispersive spectrometer (FESEM/EDS) were employed to characterize the microstructure of the as-prepared feedstock powders and nano-composite coating. At the same time, the mechanical properties and friction and wear behavior of the nano-composite coating and pure FeAl coating were comparatively evaluated by using a Vickers microindentation tester and ball-on-disk sliding wear tribotester, respectively. And the wear mechanisms for the two types of coatings are discussed in terms of their microstructure and mechanical properties. Results indicate that the nano-composite coating has a much higher hardness and fracture toughness as well as drastically increased wear resistance than pure FeAl coating, which could be mainly attributed to the reinforcing effect of ZrO₂ nano-particles and partially attributed to the refining effect of CeO₂ in the nano-composite coating.     

Plasma sprayed Al2O3/FeCrAl composite coatings for electromagnetic wave absorption application

Al₂O₃/FeCrAl composite coatings were fabricated by atmosphere plasma spraying technique. Microstructure and dielectric properties in the frequency range from 8.2 to 12.4 GHz were investigated. The microstructure of composite coatings shows a uniform dispersion of metal particles with litter pores and microcracks in the composite coatings. The relaxation polarization and interfacial polarization in the coatings would contribute to enhance ?′ with rising FeCrAl content, and the associated loss could be considered as a dominating factor enhancing ?″. By calculating the microwave-absorption as a single-layer absorber, for the composite coatings with 41 wt.% FeCrAl content, the reflection loss values exceeding −10 dB are achieved in the frequency range of 9.1-10.6 GHz when the coating thickness is 1.3 mm.     

Synthesis of anodizing composite films containing superfine Al2O3 and PTFE particles on Al alloys

Anodized composite films containing superfine Al₂O₃ and PTFE particles were prepared on 2024 Al alloy using an anodizing method. The microstructures and properties of the films were studied by scanning electron microscopy, optical microscopy and X-ray diffraction. Friction wear tests were performed to evaluate the mechanical properties of the composites. Results indicate that the composite films with reinforced Al₂O₃ and PTFE two-particles have reduced friction coefficients and relatively high microhardness. The friction coefficient can be as small as 0.15, which is much smaller than that of an oxide film prepared under the same conditions but without adding any particles (0.25), while the microhardness can reach as high as 404 HV. When rubbed at room temperature for 20 min during dry sliding friction tests, the wear loss of the film was about 16 mg, which is about the half of that of the samples without added particles. The synthesized composite films that have good anti-wear and self-lubricating properties are desirable for oil-free industrial machinery applications.     

Preparation and characterization of the electrodeposited Cr-Al2O3/SiC composite coating

To increase the SiC content in Cr-based coatings, Cr-Al₂O₃/SiC composite coatings were plated in Cr(VI) baths which contained Al₂O₃-coated SiC powders. The Al₂O₃-coated SiC composite particles were synthesized by calcining the precursor prepared by heterogeneous deposition method. The transmission electron microscopy analysis of the particles showed that the nano-SiC particle was packaged by alumina. The zeta potential of the particles collected from the bath was up to +23 mV, a favorable condition for the co-deposition of the particles and chromium. Pulse current was used during the electrodeposition. Scanning Electron Microscopy (SEM) indicated that the coating was compact and combined well with the substrate. Energy dispersive X-ray analysis of Cr-Al₂O₃/SiC coatings demonstrated that the concentration of SiC in the coating reached about 2.5 wt.%. The corrosion behavior of the composite coating was studied by potentiodynamic polarization and electrochemical impedance spectroscopy techniques. The data obtained suggested that the Al₂O₃/SiC particles significantly enhanced the corrosion resistance of the composite coating in 0.05 M HCl solution.