Efficient visible-light-induced photocatalytic degradation of MO on the Cr-nanocrystalline titania-S

In order to improve visible light photocatalytic activities of the nanometer TiO₂, a novel and efficient Cr,S-codoped TiO₂ (Cr-TiO₂-S) photocatalyst was prepared by precipitation-doping method. The crystalline structure, morphology, particle size, and chemical structure of Cr-TiO₂-S were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), scanning electron microscopy (SEM), and Fourier transform infrared (FT-IR) techniques, respectively. Results indicate that the doping of Cr and S, cause absorption edge shifts to the visible light region (λ > 420 nm) compare to the pure TiO₂, reduces average size of the TiO₂ crystallites, enhances desired lattice distortion of Ti, promotes separation of photo-induced electron and hole pair, and thus improves pollutant decomposition under visible light irradiation. The photocatalytic activities of Cr-TiO₂-S nanoparticles were evaluated using the photodegradation of methyl orange (MO) as probe reaction under the irradiation of UV and visible light and it was observed that the Cr-TiO₂-S photocatalyst shows higher visible photocatalytic activity than the pure TiO₂. The optimal Cr-TiO₂-S concentration to obtain the highest photocatalytic activity was 5 mol% for both of Cr and S.     

Fabrication and characterization of electrospun orthorhombic InVO4 nanofibers

The novel orthorhombic InVO₄ nanofibers have been successfully synthesized by annealing electrospun precursor fibers. Citric acid was used as a ligand for it could react with metal salts to get a transparent homogeneous precursor solution and homogeneous precursor sol for electrospining. Polyvinyl pyrrolidone (PVP, K-30) was used as a binder and a structure guide reagent because it was one kind of water-soluble polymers. It is easy to gain one-dimensional materials while the viscosity of the citrate/PVP sol was suitable. The structure, morphology and photocatalytic properties of the nanofibers were characterized by X-ray diffraction (XRD), thermogravimetry analysis (TGA), scanning electron microscopy (SEM) analysis, UV-vis spectrophotometer and fluorescence spectrophotometer. The nanofibers calcined at 700 °C were orthorhombic InVO₄ with a width in the range of 30-100 nm and length in micron-grade. This one-dimensional pure orthorhombic InVO₄ had the higher photocatalytic activity under visible light irradiation. The photo-degradation rate of nitrobenzene aqueous solution under visible light reached 69% after 6 h. It is obvious that the orthorhombic InVO₄ nanofibers have a potential application in wastewater-treatment.     

Synthesis, characterization and photocatalytic activities of rare earth-loaded BiVO4 catalysts

The BiVO₄-based photocatalysts loaded with rare earth (RE=Ho, Sm, Yb, Eu, Gd, Nd, Ce and La) were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), diffuse reflectance spectroscopy (DRS), nitrogen adsorption for the BET specific surface area and X-ray photoelectron spectroscopy (XPS). The photocatalytic activities of the samples were evaluated by decolorization of methylene blue (MB) under visible light irradiation. The results of XRD, SEM and XPS analysis deduced that the rare earth ions were present as RE₂O₃ in the samples. The DRS analysis showed the shift in the absorbption edge from the UV to the visible range: Ho³⁺-BiVO₄ < Sm³⁺-BiVO₄ < Yb³⁺-BiVO₄ < Eu³⁺-BiVO₄ < Gd³⁺-BiVO₄ < Nd³⁺-BiVO₄ < La³⁺-BiVO₄ < Ce³⁺-BiVO₄ < BiVO_4. Gd³⁺-BiVO₄ had the highest photocatalytic activity among all the RE³⁺-BiVO₄ catalysts. The optimal Gd content was 8 at% under visible light irradiation. This beneficial effect was attributed to the specific electron structure characteristics of gadolinium and the increasing in the separation efficiency of the electron-hole pairs. On the contrast, the other rare earth ions had the detrimental effect on the photocatalytic decolorization of MB.     

Hydrothermal synthesis of graphitic carbon nitride–BiVO4 composites with enhanced visible light photocatalytic activities and the mechanism study

Novel graphitic carbon nitride (C₃N₄) and bismuth vanadate (BiVO₄) composite photocatalysts were successfully synthesized by a facile hydrothermal method. The scanning electron microscopy (SEM) revealed that an intimate interface between C₃N₄ and BiVO₄ formed in the composites. Compared with the pure C₃N₄ and BiVO₄, the C₃N₄–BiVO₄ photocatalysts showed remarkably the higher photocatalytic activities in degrading rhodamine B (Rh B). The best active heterojunction proportion was 0.5C₃N₄–0.5BiVO₄. Over this catalyst, the 100% degradation of Rh B (0.002 mmol L⁻¹) was obtained under visible light irradiation (λ>420 nm) for 40 min. The active species in Rh B degradation were examined by adding a series of scavengers. The study on photocatalytic mechanism revealed that the electrons injected directly from the conduction band of C₃N₄ to that of BiVO₄, resulting in the production of superoxide radical (O₂^•−) and hydroxyl radical (OH^•) in the conduction band of BiVO₄. Simultaneously, the rich holes in the valence band of g-C₃N₄ oxidized Rh B directly to promote the photocatalytic degradation reaction.     

Preparation, characterization and photocatalytic performance of TiO2/CexZr1−xO2 toward the oxidation of gaseous benzene

Increasing environmental pollution caused by the volatile organic compounds due to their toxicity makes their removal imperative. So it is crucial to develop processes which can degrade these compounds effectively. The paper demonstrates that the photocatalytic activity of TiO₂ toward the decomposition of gaseous benzene in a batch reactor can be greatly enhanced by loading TiO₂ onto the surface of Ce_xZr_1−xO₂ (x ≥ 0.25) using sol-gel technology. This research investigated the relationship between x amount and the photocatalytic activity of TiO₂. The prepared photocatalysts were characterized by BET, XRD, UV-vis diffuse reflectance and XPS analyses. The specific surface area of photocatalyst decreases as x decreases. XRD results reveal the no peaks of titania were detected. Among the five catalysts prepared, only the binding energy values of Ti2p_3/2 of TiO₂/Ce_0.5Zr_0.5O₂ shift toward lower value. The order of photocatalytic activity is TiO₂/Ce_0.5Zr_0.5O₂ > TiO₂/Ce_0.75Zr_0.25O₂ > TiO₂/CeO₂ ≈ TiO₂/Ce_0.25Zr_0.75O₂ > TiO₂/ZrO₂ ≈ TiO₂. The mechanism role of Ceria-Zirconia mixed oxides in photocatalytic reaction was speculated.     

Surface modification of nanocrystalline anatase with CTAB in the acidic condition and its effects on photocatalytic activity and preferential growth of TiO2

The nanocrystalline anatase TiO₂, which was synthesized by a sol-hydrothermal process in advance, has successfully modified with cetyltrimethylammonium bromide (CTAB) in the acidic condition as well as in the basic condition. On the basis of the measurements of infrared spectrum and X-ray photoelectron spectroscopy of the resulting TiO₂, together with the phase-transfer experiments, it is suggested that the modification mechanism in the acidic condition is closely related to Br⁻. Interestingly, compared with un-modified TiO₂, the modified TiO₂ exhibits high photocatalytic activity for degrading Rhodamine B (RhB) solution, especially for that modified in the acid. The enhanced photocatalytic activity of modified TiO₂ in the acid is attributed to the role that the Br⁻ can easily capture photo-induced holes and then form active Br, consequently effectively inducing photocatalytic oxidation reactions, based on the surface photovoltage responses of the resulting TiO₂. After that, a one-pot sol-hydrothermal route at the temperature as low as 80 °C is developed to directly synthesize CTAB-modified nanocrystalline TiO₂ with a little preferred growth along 〈0 0 1〉 direction, which can be easily dispersed in the organic system and possess good photocatalytic performance. This work provides a feasible strategy to further improve the photocatalytic performance of nanocrystalline anatase and to synthesize TiO₂ nanocrystals with preferential growth.     

Effect of surface species on Cu-TiO2 photocatalytic activity

The Cu-TiO₂ nanoparticles with different Cu dopant content were prepared by sol-gel method. The structure of the as-prepared catalysts and the surface species of Cu-TiO₂ were determined using X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and diffuse reflection spectroscopy (DRS). The relationship between the photocatalytic activity and the surface species of Cu-TiO₂ was revealed via the measurement of surface photovoltage spectroscopy (SPS) as well as the degradation of the rhodamine B (RhB). The experimental results suggest that the Cu-TiO₂ photocatalysts with appropriate content of Cu (about 0.06 mol%) possess abundant electronic trap, which effectively inhibits the recombination of photoinduced charge carriers, improving the photocatalytic activity of TiO₂. While at high Cu dopant region (>0.06 mol%), the excessive oxygen vacancies and Cu species can become the recombination centers of photoinduced electrons and holes. Meanwhile, at heavy Cu doping concentration, excessive P-type Cu₂O can cover the surface of TiO₂, which leads to decrease in the photocatalytic activity of photocatalyst. The photocatalytic experimental results are in good agreement with the conclusions of SPS measurements, indicating that there is a close relationship between the photocatalytic activity and the intensity of SPS spectra.     

Synthesis and photocatalytic properties of porous TiO2 films prepared by ODA/sol-gel method

Porous TiO₂ films were deposited on SiO₂ pre-coated glass-slides by sol-gel method using octadecylamine (ODA) as template. The amount of ODA in the sol played an important role on the physicochemical properties and photocatalytic performance of the TiO₂ films. The films prepared at different conditions were all composed of anatase titanium dioxide crystals, and TiO₂ crystalline size got larger with increasing ODA amount. The maximum specific surface area of 41.5 m²/g was obtained for TiO₂ powders prepared from titanium sol containing 2.0 g ODA. Methyl orange degradation rate was enhanced along with increasing ODA amount and reached the maximal value at 2.0 g addition of ODA. After 40 min of UV-light irradiation, methyl orange degradation rate reached 30.5% on the porous film, which was about 10% higher than that on the smooth film. Porous TiO₂ film showed almost constant activity with slight decrease from 30.5% to 28.5% after 4 times of recycles.     

Characterization and activity of visible-light-driven TiO2 photocatalyst codoped with lanthanum and iodine

The novel visible-light-activated La/I/TiO₂ nanocomposition photocatalyst was successfully synthesized using precipitation-dipping method, and characterized by X-ray powder diffraction (XRD), the Brunauer-Emmett-Teller (BET) method, transmission electron microscopy (TEM), thermogravimetry-differential scanning calorimetry (TG-DSC) and UV-vis diffuse reflectance spectroscopy (UV-vis DRS). The photocatalytic activity of La/I/TiO₂ was evaluated by studying photodegradation of reactive blue 19 as a probe reaction under simulated sunlight irradiation. Photocatalytic experiment results showed that the maximum specific photocatalytic activity of the La/I/TiO₂ photocatalyst appeared when the molar ratio of La/Ti was 2.0 at%, calcined at 350 °C for 2 h, due to the sample with good crystallization, high BET surface area and small crystal size. Under simulated sunlight irradiation, the degradation of reactive blue 19 aqueous solution reached 98.6% in 80 min, which showed La/I/TiO₂ photocatalyst to be much higher photocatalytic activity compared to standard Degussa P25 photocatalyst. The higher visible light activity is due to the codoping of lanthanum and iodine.     

TiO2 thick films supported on reticulated macroporous Al2O3 foams and their photoactivity in phenol mineralization

TiO₂ thick films deposited on macroporous reticulated Al₂O₃ foams with pore size of 10 ppi and 15 ppi were prepared using dip coating from slurries of Aeroxide^® P25 nanopowder and precipitated titania. All prepared films have sufficiently good adhesion to the surface of the substrate also in case of strongly cracked films. No measurable release of deposited TiO₂ after repeated photocatalytic cycles was observed. The photocatalytic activity was characterized as the rate of mineralization of aqueous phenol solution under irradiation of UVA light by TOC technique. The best activity was obtained with Aeroxide^® P25 coated Al₂O₃ foam with the pore size of 10 ppi, annealed at 600 °C. The optimal annealing temperature for preparation of films from precipitated titania could be determined at 700 °C. Films prepared by sol-gel deposition technique were considerably thinner compared to coatings made of suspensions and their photocatalytic activity was significantly smaller.     

Enhanced photocatalytic activity of TiO2 nano-structured thin film with a silver hierarchical configuration

TiO₂ sol-gels with various Ag/TiO₂ molar ratios from 0 to 0.9% were used to fabricate silver-modified nano-structured TiO₂ thin films using a layer-by-layer dip-coating (LLDC) technique. This technique allows obtaining TiO₂ nano-structured thin films with a silver hierarchical configuration. The coating of pure TiO₂ sol-gel and Ag-modified sol-gel was marked as T and A, respectively. According to the coating order and the nature of the TiO₂ sol-gel, four types of the TiO₂ thin films were constructed, and marked as AT (bottom layer was Ag modified, surface layer was pure TiO₂), TA (bottom layer was pure TiO₂, surface layer was Ag modified), TT (pure TiO₂ thin film) and AA (TiO₂ thin film was uniformly Ag modified). These thin films were characterized by means of linear sweep voltammetry (LSV), X-ray diffraction (XRD), scanning electron microscopy (SEM), electrochemical impedance spectroscopy and transient photocurrent (I_ph). LSV confirmed the existence of Ag⁰ state in the TiO₂ thin film. SEM and XRD experiments indicated that the sizes of the TiO₂ nanoparticles of the resulting films were in the order of TT > AT > TA > AA, suggesting the gradient Ag distribution in the films. The SEM and XRD results also confirmed that Ag had an inhibition effect on the size growth of anatase nanoparticles. Photocatalytic activities of the resulting thin films were also evaluated in the photocatalytic degradation process of methyl orange. The preliminary results demonstrated the sequence of the photocatalytic activity of the resulting films was AT > TA > AA > TT. This suggested that the silver hierarchical configuration can be used to improve the photocatalytic activity of TiO₂ thin film.     

Aerosol-assisted flow synthesis of WxTi1−xO2 solid solution spheres with enhanced photocatalytic activity

In this paper, W_xTi_1−xO₂ solid solutions (x = 0.000, 0.005, 0.010, 0.015, and 0.020) microspheres were synthesized with an aerosol-assisted flow synthesis method. The resulting samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), nitrogen sorption, UV-vis diffuse reflectance spectrum (DRS) and X-ray photoelectron spectroscopy (XPS). The photocatalytic activities of the as-prepared catalysts were measured by the degradation of rhodamine B (RhB) under visible light irradiation (λ ≥ 420 nm). All the solid solutions exhibited higher photocatalytic activities than pure TiO₂ and the W_0.015Ti_0.985O₂ solid solution possessed the highest photocatalytic activity. The degradation constant of RhB on W_0.015Ti_0.985O₂ solid solution catalyst was about 15 times of that of the pure TiO₂ and 25 times of that of Degussa P25, respectively. This study provides an effective method to prepare visible light photocatalysts on a large scale.     

Reasons for the deactivation of Pt/TiO2 photocatalyst treated by inert gas N2

The effect of N₂ treatment on the photocatalytic activity of Pt⁰/TiO₂ was investigated. The results showed that after treatment at 500 °C in N₂, 70% of the photocatalytic activity of 1.0 wt.% Pt⁰/TiO₂ was lost by the evaluation of photocatalytic oxidation reaction of C₃H₆. Transmission electron microscopy (TEM) and Ar⁺ ion sputtering tests revealed that in the course of high-temperature N₂ treatment, the size of Pt⁰ particles on TiO₂ increases and a strong interaction between metal and support, i.e. Pt⁰ particles encapsulated by Ti_xO_y, happens, which are the reasons for the deactivation of Pt⁰/TiO₂ photocatalyst treated by high-temperature N₂.     

Roles of oleic acid during micropore dispersing preparation of nano-calcium carbonate particles

In the present work, nano-calcium carbonate powder was prepared by micropore dispersion method with assistance of oleic acid as surfactant. CO₂ gas was dispersed into the Ca(OH)₂/H₂O slurry via a glass micropore-plate with the diameter of micropore about 20 μm. To investigate the effect of oleic acid on the size of CaCO₃ particles, different amount of oleic acid was added in Ca(OH)₂/H₂O slurry at 5 °C and 25 °C, respectively. XRD patterns show that cubic calcite is the only crystalline phase in all cases. ZPA data and TEM photo indicate that the average particle size synthesized at 5 °C without oleic acid is of about 40 nm, slightly smaller than that of prepared at 25 °C, and that the dispersity of sample prepared at 5 °C is better than that of 25 °C. When oleic acid is added in both temperatures, the average particle size decreases a little. FT-IR spectra demonstrate that oleic acid interacts with Ca²⁺ and carbon-carbon double bond existed on the surface of particle. Consequently, two opposite roles of oleic acid during the process of preparation of nano-CaCO₃ were proposed, namely preventing nanoparticles from growing during reaction and making nanoparticles reunite to a certain extent after reaction.     

TiO2 activation using acid-treated vermiculite as a support: Characteristics and photoreactivity

Vermiculite was treated by sulfuric or nitric acid aqueous solutions with different concentration. These modified materials as the promising supports, were used to immobilize TiO₂. TiO₂ was prepared by the precursor, which was obtained by substituting partly isopropyl alcohol with Cl⁻ in titanium chloride {[Ti(IV)(OR)_nCl_m] (n = 2-3, m = 4 − n)}. The TiO₂/vermiculite composites were characterized by X-ray diffraction, scanning electron microscopy, and the nitrogen absorption. Their photocatalytic activity was evaluated by removal of methylene blue (MB). The pure anatase type crystalline phase was well deposited on the supports. The concentrations of acid for treatment had a significant influence on pore sizes and surface area of vermiculite. The treatment process changed microstructure of vermiculite, modified its characteristics, and farther improved the catalytic activity and absorption capacity of TiO₂/vermiculite composites. The treatment effect of nitric acid was superior to that of sulfuric acid.     

One-pot synthesis of Ag+ doped BiVO4 microspheres with enhanced photocatalytic activity via a facile hydrothermal method

The Ag⁺/BiVO₄ photocatalyst was fabricated through a facile hydrothermal method by using K₆V₁₀O₂₈·9H₂O as the vanadium source. The impact of Ag⁺ on the product's structure and morphology was studied. It was shown that the amount of Ag⁺ has no effect on the product’s crystal phases but plays an important role on the morphology of the nanoparticles that construct the shell of BiVO₄ microspheres. In addition, the Ag⁺-doped photocatalysts have much higher photocatalytic activities in removing RhB and MB under the UV light illumination than the pure BiVO₄. A possible photocatalytic mechanism was proposed in photoexcitation of the BiVO₄ electrons which subsequently captured by the dopant. The present work may offer a novel route to reach higher photocatalytic activity by doping the Ag⁺ in the semiconductor catalysts.     

P/Si-TiO2 transparent films with high anatase stability and photocatalytic activity

The anatase-TiO₂ transparent films, containing 3 mol% of Si and P elements (as dopants), were synthesized using a process combining the sol-gel method and spin-coating technique. Effects of relative ratio of dopants and calcination temperature on phase transformation, grain growth, surface morphology, light transmittance, band-gap energy and photocatalytic activity of the P/Si-TiO₂ films were examined and their results were compared with those of the undoped-TiO₂ and Si-TiO₂ films. The P/Si-TiO₂ films calcined at temperature between 600 and 900 °C adhered strongly to the surface of fused-silica substrate and were composed of anatase-TiO₂ monophase. The photocatalytic activities of the films were measured and represented using a characteristic time constant (τ) for the methylene blue (MB) photodegradation. The small τ stands for high photocatalytic ability of the film. The P/Si-TiO₂ film, containing equalmolar Si and P dopants, calcined at 800 °C gave the best performance in photocatalysis; this film had τ=5.7 h and decomposed about 90 mole% of MB in the water after 12 h of the 365-nm UV light irradiation.     

Phase transition of BiVO4 nanoparticles in molten salt and the enhancement of visible-light photocatalytic activity

BiVO₄ nanoparticles are prepared by molten salt method. Tetragonal BiVO₄ completely transforms to monoclinic phase after heating in molten LiNO₃ at 270 °C for 18 h. The average particle sizes of monoclinic BiVO₄ varied from 30 to 52 nm while the initial ratio of BiVO₄ to LiNO₃ changes from 1:6 to 1:24. The photocatalytic activity is evaluated by measuring decolorization of N,N,N′,N′-tetraethylated rhodamine dye solution under visible-light irradiation. Both of the de-ethylation and chromophore cleavage are responsible for the decolorization of RB. The sample with an average particle size of 52 nm and a moderate surface area of 10 m²/g exhibit the highest visible-light photocatalytic activity. The shift of Raman peak position indicates that the symmetry distortions in the local structure of the monoclinic BiVO₄. The variations of the local structure result in the modification of the electronic structure, which is responsible for the high visible-light photocatalytic activity.     

Effect of boric acid on structure,morphology and luminescent properties of divalent europium doped calcium aluminate phosphors

Blue phosphors Ca_1 − xAl₂O₄: xEu²⁺ were prepared by high temperature solid-state method. Their structure, morphology and luminescent properties were investigated by X-ray diffraction (XRD), scanning electron microscope (SEM) and fluorescence spectroscopy. The effect of different amounts of fluxing agent H₃BO₃ on structure, morphology and luminescent properties of blue phosphors Ca_1 − xAl₂O₄: xEu²⁺ luminous intensity caused by different amount of H₃BO₃ was also investigated. The amount of H₃BO₃ doped Ca_1 − xAl₂O₄: xEu²⁺ in optimal luminous intensity had been determined. The results showed that both the excitation and emission spectra of samples were all broad bands, and that the peak of emission spectra was near 442 nm, which was corresponding to the 4f⁶5d → 4f⁷ transition of Eu²⁺ illuminating blue light. Ca_1 − xAl₂O₄: xEu²⁺ (x = 3.5 mol%) could be gained with good morphology and the best luminous intensity when H₃BO₃ mass ratio was 0.5 wt%.     

Preparation and visible light photocatalytic activity of mesoporous N, S-codoped TiO2(B) nanobelts

The mesoporous N, S-codoped TiO₂(B) nanobelts are synthesized via hydrothermal synthesis and post-treatment, and characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), N₂ adsorption-desorption measurements (BET), X-ray photoelectron spectra (XPS), and UV-vis diffuse reflectance spectra (DRS). The results show that the prepared samples are mesoporous structured and exhibit stronger absorption in the visible light region with red shift in the absorption edge. The photocatalytic activity of N, S-codoped mesoporous TiO₂(B) nanobelts is evaluated by the photocatalytic photodegradation of potassium ethyl xanthate (KEX) under visible light irradiation. It is found that the photocatalytic activity of the prepared samples increases with increasing the molar ratio of thiourea to Ti (R). At R = 3, the photocatalytic activity of the N, S-codoped TiO₂(B) sample TBLTS-3 reaches a maximum value. With further increasing R, the photocatalytic activity of the sample decreases. The high photocatalytic activity of N, S-codoped TiO₂(B) nanobelts can be attributed to the balance between strong absorption in visible light region and low recombination rate of electron/hole pairs.