Preparation of activated carbon from a renewable bio-plant of Euphorbia rigida by H2SO4 activation and its adsorption behavior in aqueous solutions

The use of activated carbon obtained from Euphorbia rigida for the removal of a basic textile dye, which is methylene blue, from aqueous solutions at various contact times, pHs and temperatures was investigated. The plant material was chemically modified with H₂SO₄. The surface area of chemically modified activated carbon was 741.2 m² g⁻¹. The surface characterization of both plant- and activated carbon was undertaken using FTIR spectroscopic technique. The adsorption process attains equilibrium within 60 min. The experimental data indicated that the adsorption isotherms are well described by the Langmuir equilibrium isotherm equation and the calculated adsorption capacity of activated carbon was 114.45 mg g⁻¹ at 40° C. The adsorption kinetics of methylene blue obeys the pseudo-second-order kinetic model and also followed by the intraparticle diffusion model up to 60 min. The thermodynamic parameters such as ΔG°, ΔH° and ΔS° were calculated to estimate the nature of adsorption. The activation energy of the system was calculated as 55.51 kJ mol⁻¹. According to these results, prepared activated carbon could be used as a low-cost adsorbent to compare with the commercial activated carbon for the removal textile dyes from textile wastewater processes.     

Optimization of nickel adsorption from aqueous solution by using activated carbon prepared from waste apricot by chemical activation

Waste apricot supplied by Malatya apricot plant (Turkey) was activated by using chemical activation method and K₂CO₃ was chosen for this purpose. Activation temperature was varied over the temperature range of 400-900 °C and N₂ atmosphere was used with 10 °C/min heat rate. The maximum surface area (1214 m²/g) and micropore volume (0.355 cm³/g) were obtained at 900 °C, but activated carbon was predominantly microporous at 700 °C. The resulting activated carbons were used for removal of Ni(II) ions from aqueous solution and adsorption properties have been investigated under various conditions such as pH, activation temperature, adsorbent dosage and nickel concentration. Adsorption parameters were determined by using Langmuir model. Optimal condition was determined as; pH 5, 0.7 g/10 ml adsorbent dosage, 10 mg/l Ni(II) concentration and 60 min contact time. The results indicate that the effective uptake of Ni(II) ions was obtained by activating the carbon at 900 °C.     

Removal of lead(II) by adsorption onto Viscumalbum L.: Effect of temperature and equilibrium isotherm analyses

The removal efficiency of Viscumalbum L. from lead containing aqueous solutions was investigated. The effect of adsorbent mass, pH of solution, initial Pb(II) concentration and temperature was investigated using a batch adsorption technique. The optimum pH for Pb(II) adsorption was found as 3.0 for Viscumalbum L. Results were analyzed by the Langmuir, Freundlich, Temkin and Harkins-Jura, equation using linearized correlation coefficient at different temperature. The characteristic parameters for each isotherm have been determined. The Langmuir model agrees very well with experimental data than the other models. According to Langmuir isoterm, the monolayer saturation capacity (Q_o) is 769.23 mg/g at 25 °C. Models and the isotherm constant were evaluated depending on temperature. Thermodynamic parameters such as ΔH^o, ΔS^o and ΔG^o were calculated. The adsorption process was found to be endothermic and spontaneous. The experimental data were analyzed using the first- and the second-order kinetic models. The rate constants of adsorption for both kinetics models have been calculated. The second-order model provides the best correlation of the data.     

Preparation and hydrogen storage of activated rayon-based carbon fibers with high specific surface area

Activated carbon fibers were prepared from rayon-based carbon fibers by two step activations with steam and KOH treatments. Hydrogen storage properties of the activated rayon-based carbon fibers with high specific surface area and micropore volume have been investigated. SEM, XRD and Brunauer-Emmett-Teller (BET) were used to characterize the samples. The adsorption performance and porous structure were investigated by nitrogen adsorption isotherm at 77 K on the base of BET and density functional theory (DFT). The BET specific surface area and micropore volume of the activated rayon-based carbon fibers were 3144 m²/g and 0.744 m³/g, respectively. Hydrogen storage properties of the samples were measured at 77 and 298 K with pressure-composition isotherm (PCT) measuring system based on the volumetric method. The capacities of hydrogen storage of the activated rayon-based carbon fibers were 7.01 and 1.46 wt% at 77 and 298 K at 4 MPa, respectively. Possible mechanisms for hydrogen storage in the activated rayon-based carbon fibers are discussed.     

Adsorption and solid phase extraction of 8-hydroxyquinoline from aqueous solutions by using natural bentonite

The nitrogen-heterocyclic compound 8-hydroxyquinoline (8HQ) is one of the components of coal tar and has a wide variety of uses in industry. Because of its toxicity for aquatic organisms and harmful effects for human health, the removal of 8HQ from aqueous solutions by adsorption onto natural bentonite was investigated in the present work. The experimental results show that the optimum pH value of 2.5 is favourable for the 8HQ adsorption. The experimental data were fitted well with the pseudo-second-order kinetic and Langmuir adsorption isotherm models at all studied temperatures. The maximum adsorption capacity obtained from the Langmuir isotherm model at 20 °C was 120.6 mg g⁻¹. The calculated thermodynamic results such as ΔG° (−24.3 kJ mol⁻¹) and ΔH° (−9.56 kJ mol⁻¹) indicate that the adsorption process is spontaneous and exothermic in nature. Solid phase extraction of 8HQ was also performed. The X-ray diffractometry (XRD), Fourier Transform Infrared (FTIR) and thermogravimetric (TG) analyses were carried out in order to confirm the 8HQ adsorption onto bentonite. According to the obtained results, natural bentonite can be a reusable and effective adsorbent for the removal of 8HQ.     

Application of bifunctional Saccharomyces cerevisiae to remove lead(II) and cadmium(II) in aqueous solution

A magnetic adsorbent, EDTAD-functionalized Saccharomyces cerevisiae, has been synthesized to behave as an adsorbent for heavy metal ions by adjusting the pH value of the aqueous solution to make carboxyl and amino groups protonic or non-protonic. The bifunctional Saccharomyces cerevisiae (EMS) were used to remove lead(II) and cadmium(II) in solution in a batch system. The results showed that the adsorption capacity of the EMS for the heavy metal ions increased with increasing solution pH, and the maximum adsorption capacity (88.16 mg/g for Pb²⁺, 40.72 mg/g for Cd²⁺) at 10 °C was found to occur at pH 5.5 and 6.0, respectively. The adsorption process followed the Langmuir isotherm model. The regeneration experiments revealed that the EMS could be successfully reused.     

纸质活性炭纤维的制备及性能表征

通过KOH活化纸巾制备活性炭纤维, 比表面积高达1388 m²/g. 用制得的活性炭纤维作为吸附剂进行亚甲基蓝吸附实验研究,用Langmuir和Freundlich吸附模型分析实验数据,并研究pH值对活性炭纤维吸附亚甲基蓝影响. 活性炭纤维吸附速率更适于Pseudo-second-order动力学模型,相关系数高达0.998. 整个浓度变化区间Langmuir吸附等温线比Freundlich吸附等温线更适合实验数据. 所制备活性炭纤维对亚甲基蓝最大平衡吸附量为520 mg/g,实验发现,pH值越高活性炭纤维对亚甲基蓝吸附量越大.     

Biomass waste-derived activated carbon for the removal of arsenic and manganese ions from aqueous solutions

The goal of this study is to investigate the preparation of low-cost activated carbon from bean pods waste and to explore their potential application for the removal of heavy metals from aqueous solutions. Conventional physical (water vapor) activation was used for synthesizing the adsorbent. The obtained carbon was employed for the removal of As (III) and Mn (II) from aqueous solutions at different initial concentrations and pH values. Adsorption for both ions follows Langmuir-type isotherm, the maximum loading capacities for arsenic (III) and Mn (II) ions being 1.01 and 23.4 mg g⁻¹, respectively. According to the experimental data, it can be inferred that the basic character of the surface, i.e. the high content of basic groups, favors adsorption of ions. Arsenic adsorption capacity on the carbon obtained from agricultural waste was found to be similar to this of more expensive commercial carbons showing high adsorption capability. Regarding manganese adsorption, herein obtained carbon presented higher uptake adsorption than that of activated carbons reported in the literature.     

Surface and adsorptive properties of carbons prepared from biomass

A number of activated carbons were prepared from a locally available by-product, corncobs, under currently established activation schemes. Obtained carbons were characterized by N₂ adsorption at 77 K and the isotherms were analyzed by BET and α_s methods. Steam-activation at 900 °C produced a microporous carbon having the highest S^α of 788 m² g⁻¹, whereas activation with air at 350 °C produced a carbon of S^α = 321 m²/g and possess wider pores. KOH impregnation with char in ratio 1:1 (w/w) and impregnated in the same ratio with the raw material prior to pyrolysis at 700 °C for 1 h, gave CK700, K700 respectively. An additional sample was obtained by oxidizing part of K700 with conc. HNO₃. All three KOH carbons show pore structures much close to char itself which may be due to potassium salt left in pores and is not easily leached with repeated water washings. In addition, KOH is more effective on the precursor itself than on its char of already developed porosity. FT-IR spectra show an increase in oxygen functionalties on the carbon surface as a result of activation process and the bands become stronger in the spectra of the acid-treated sample. The oxidized carbon sample showed relatively higher uptake of Pb²⁺ and MB and its surface chemistry plays the key role in their adsorption, while sharp decrease was observed in the uptake of phenol and mono-nitrophenols from aqueous solutions. An SEM study showed that air activation produce obvious voids reflecting its erosive effect on the external carbon surface.     

Kinetics and thermodynamics of Pb(II) adsorption onto modified spent grain from aqueous solutions

Spent grain, a main by-product of the brewing industry, is available in large quantities, but its main application has been limited to animal feeding. Nevertheless, in this study, spent grain modified with 1 M NaCl solution as a novel adsorbent has been used for the adsorption of Pb(II) in aqueous solutions. Isotherms, kinetics and thermodynamics of Pb(II) adsorption onto modified spent grain were studied. The equilibrium data were well fitted with Langmuir, Freundlich and Dubinin-Radushkevick (D-R) isotherm models. The kinetics of Pb(II) adsorption followed pseudo-second-order model, using the rate constants of pseudo-second-order model, the activation energy (E_a) of Pb(II) adsorption was determined as 12.33 kJ mol⁻¹ according to the Arrhenius equation. Various thermodynamic parameters such as ΔG^ads, ΔH^ads and ΔS^ads were also calculated. Thermodynamic results indicate that Pb(II) adsorption onto modified spent grain is a spontaneous and endothermic process. Therefore, it can be concluded that modified spent grain as a new effective adsorbent has potential for Pb(II) removal from aqueous solutions.     

Chitin-humic acid hybrid as adsorbent for Cr(III) in effluent of tannery wastewater treatment

Adsorption of Cr(III) from both synthetic and real samples of tannery wastewater treatment's effluent on chitin-humic acid (chitin-HA) hybrid has been carried out. Rate constant and capacity of adsorption of Cr(III) from the synthetic sample were investigated and removal of Cr(III) from the real sample was tested at optimum medium acidity equivalent to pH 3.5. Characterization using Fourier transform infra red (FT-IR) spectroscopy revealed that both COO⁻ and N-acetyl originated from respectively humic acid (HA) and chitin were involved on the adsorption of Cr(III), and hence the Freundlich's multilayer and multi-energy adsorption model was more applicable to treat the adsorption data than the Langmuir's monolayer and mono-energy model. The quantification of adsorption capacity and rate constant using Freundlich isotherm model and first order adsorption reaching equilibrium yielded values of 6.84 × 10⁻⁴ mol g⁻¹ (35.57 mg g⁻¹) and 1.70 × 10⁻² min⁻¹, respectively. Removal test for the real wastewater treatment's effluent showed that the maximum amount of Cr(III) could be removed by 1 g of chitin-HA hybrid was 2.08 × 10⁻⁴ mol or equivalent to 10.82 mg.     

Synthesis of magnetic γ-Fe2O3-based nanomaterial for ultrasonic assisted dyes adsorption: Modeling and optimization

γ-Fe₂O₃ nanoparticles were synthesized and loaded on activated carbon. The prepared nanomaterial was characterized by field emission scanning electron microscopy (FE-SEM), energy-dispersive X-ray spectroscopy (EDX), Fourier transforms infrared spectroscopy (FT-IR) and X-ray diffraction (XRD). The γ-Fe₂O₃ nanoparticle-loaded activated carbon (γ-Fe₂O₃-NPs-AC) was used as novel adsorbent for the ultrasonic-assisted removal of methylene blue (MB) and malachite green (MG). Response surface methodology and artificial neural network were applied to model and optimize the adsorption of the MB and MG in their individual and binary solutions followed by the investigation on adsorption isotherm and kinetics. The individual effects of parameters such as pH, mass of adsorbent, ultrasonication time as well as MB and MG concentrations in addition to the effects of their possible interactions on the adsorption process were investigated. The numerical optimization revealed that the optimum adsorption (>99.5% for each dye) is obtained at 0.02 g, 15 mg L⁻¹, 4 min and 7.0 corresponding to the adsorbent mass, each dye concentration, sonication time and pH, respectively. The Freundlich, Langmuir, Temkin and Dubinin–Radushkevich isotherms were studied. The Langmuir was found to be most applicable isotherm which predicted maximum monolayer adsorption capacities of 195.55 and 207.04 mg g⁻¹ for the adsorption of MB and MG, respectively. The pseudo-second order model was found to be applicable for the adsorption kinetics. Blank experiments (without any adsorbent) were run to investigate the possible degradation of the dyes studied in presence of ultrasonication. No dyes degradation was observed.     

Adsorptive removal of congo red dye from aqueous solution using bael shell carbon

This study investigates the potential use of bael shell carbon (BSC) as an adsorbent for the removal of congo red (CR) dye from aqueous solution. The effect of various operational parameters such as contact time, temperature, pH, and dye concentration were studied. The adsorption kinetics was modeled by first-order reversible kinetics, pseudo-first-order kinetics, and pseudo-second-order kinetics. The dye uptake process obeyed the pseudo-second-order kinetic expression at pH 5.7, 7 and 8 whereas the pseudo-first-order kinetic model was fitted well at pH 9. Langmuir, Freundlich and Temkin adsorption models were applied to fit adsorption equilibrium data. The best-fitted data was obtained with the Freundlich model. Thermodynamic study showed that adsorption of CR onto BSC was endothermic in nature and favorable with the positive ΔH° value of 13.613 kJ/mol.     

An ion-imprinted amino-functionalized silica gel sorbent prepared by hydrothermal assisted surface imprinting technique for selective removal of cadmium (II) from aqueous solution

A new ion-imprinted amino-functionalized silica gel sorbent was synthesized by the hydrothermal-assisted surface imprinting technique using Cd²⁺ as the template, 3-[2-(2-aminoethylamino)ethylamino]propyl-trimethoxysilane (AAAPTS) as the functional monomer, and epichlorohydrin as the cross-linking agent (IIP-AAAPTS/SiO₂) for the selective removal of Cd²⁺ from aqueous solution, and was characterized by FTIR, SEM, nitrogen adsorption and the static adsorption-desorption experiment method. The specific surface area of the IIP-AAAPTS/SiO₂ sorbents was found to be 149 m² g⁻¹. The results showed that the maximum static adsorption capacities of IIP-AAAPTS/SiO₂ sorbents by hydrothermal heating method and by the conventional heating method were 57.4 and 31.6 mg g⁻¹, respectively. The IIP-AAAPTS/SiO₂ sorbents offered a fast kinetics for the adsorption and desorption of Cd(II). The relative selectivity coefficients of IIP-AAAPTS/SiO₂ sorbents for Cd²⁺/Co²⁺, Cd²⁺/Ni²⁺, Cd²⁺/Zn²⁺, Cd²⁺/Pb²⁺ and Cd²⁺/Cu²⁺ were 30.68, 14.02, 3.00, 3.12 and 6.17, respectively. IIP-AAAPTS/SiO₂ sorbents had a substantial binding capacity in the range of pH 4-8 and could be used repeatedly. Equilibrium data fitted perfectly with Langmuir isotherm model compared to Freundlich isotherm model. Kinetic studies indicated that adsorption followed a pseudo-second-order model. Negative values of ΔG° indicated spontaneous adsorption and the degree of spontaneity of the reaction increased with increasing temperature. ΔH° of 26.13 kJ mol⁻¹ due to the adsorption of Cd²⁺ on the IIP-AAAPTS/SiO₂ sorbents indicated that the adsorption was endothermic in the experimental temperature range.     

Wettability modification of pitch-based spherical activated carbon by air oxidation and its effects on phenol adsorption

The surface chemistry of pitch-based spherical activated carbon (PSAC) was modified by air oxidation to enhance its wettability as well as adsorption properties. Changes of PSAC after modification in texture, surface chemistry and wettability were studied by different techniques including N₂ adsorption, X-ray photoelectron spectroscopy (XPS) and dynamic contact angle analyzer (DCA). Phenol adsorption characteristics in different solvents on PSAC were also investigated. When PSAC was modified under an atmosphere with 20 vol.% oxygen at 400 and 450 °C for 5 h, surface acidic groups increased from 0.11 to 1.22 and 1.60 meq/g, while basic groups decreased from 0.52 to 0.03 and 0.02 meq/g, respectively. After PSAC was modified, the increase of the oxygen-containing groups, especially carboxylic and phenolic ones, is responsible for the increasing of the surface acidity and the significant improvement of the wettability of PSAC. PSAC with a relatively high oxygen content provided a low adsorption capacity to phenol in aqueous solution, and the adsorption isotherms change from Langmuir class (L) to the S-shaped curve; while the solvent is changed into cyclohexane, all adsorption isotherms are type L, and the adsorption capacity to phenol increases with increasing oxygen-containing groups. Possible reasons, including the solvent effect, π-π dispersion and donor-acceptor interactions are discussed.     

Adsorption of methylene blue onto sonicated sepiolite from aqueous solutions

The aim of the present study is to enhance the methylene blue (MB) adsorption of sepiolite by ultrasonic treatment. The natural sepiolite was pretreated by sonication to improve the surface characteristics and enhance the dye uptake capacity. Sonication process resulted in a significant increase in the specific surface area (SSA) of sepiolite. The FTIR spectrum of the sonicated sepiolite indicates that the tetrahedral sheet is probably distorted after sonication process. The effect of various parameters such as sonication, pH, initial dye concentration and temperature on dye adsorption has been investigated. The adsorbed amount of MB on sepiolite increased after sonication as well as with increasing pH and temperature. The experimental data were evaluated by applying the pseudo-first- and second-order, and the intraparticle diffusion adsorption kinetic models. Adsorption process of MB onto sepiolite followed the pseudo-second-order rate expression. The experimental data were analyzed by Langmuir and Freundlich isotherms, and found that the isotherm data were reasonably well correlated by Langmuir isotherm. Maximum monolayer adsorption capacity of sepiolite for MB increased from 79.37 to 128.21 mg/g after the sonication. Various thermodynamic parameters, such as ΔG⁰, ΔH⁰ and ΔS⁰ were calculated. The thermodynamics of MB/sepiolite system indicated spontaneous and endothermic nature of the process. Adsorption measurements showed that the process was very fast and physical in nature.     

1,3-Bis(3-hyroxymethyl-5-methyl-1-pyrazole) propane as corrosion inhibitor for steel in 0.5 M H2SO4 solution

The effect of addition of 1,3-bis(3-hyroxymethyl-5-methyl-1-pyrazole) propane (M = 264 g). HMPP on steel corrosion in 0.5 M sulphuric acid is studied by weight-loss, electrochemical polarisation and electrochemical impedance spectroscopy (EIS) measurements at various temperatures. The results obtained showed that HMPP acts as a good corrosion inhibitor. The inhibition efficiency increases with the bipyrazole compound to attain 88%. It acts as a mixed-type inhibitor. Trends in the increase of charge-transfer resistance and decrease of capacitance values also show the adsorption of the molecule on the metal surface. The bipyrazole adsorbs on the steel surface according to the Langmuir isotherm adsorption model. Effect of temperature indicates that inhibition efficiency decreases with temperature between 25 and 85 °C.     

Effect of precursor preoxidation on the structure of phenolic resin-based activated carbon spheres

Activated carbon spheres with 3D hierarchical porous structure were prepared from phenol-formaldehyde resins with oxidation treatment in air and physical activation in an inert atmosphere. Based on the results of thermogravimetric analysis, infrared spectrometer (IR), scanning electron microscopy (SEM) and nitrogen adsorption/desorption, the effect of preoxidation on the morphology and structure of activated carbon spheres was investigated. The results show that decomposition and crosslinking reactions occur during the preoxidation and the structural changes of precursor generated by the preoxidation lead to differences in the pore structure of activated carbon spheres. The carbon spheres exhibit the unique 3D hierarchical porous structure, high specific surface area of 1897 m²/g and high pore volume of 2.22 cm³/g.     

Preparation and characterization of hexadecyl functionalized magnetic silica nanoparticles and its application in Rhodamine 6G removal

In this paper, a new adsorbent, hexadecyl functionalized magnetic silica nanoparticles (C₁₆/SiO₂-Fe₃O₄ NPs), was prepared by a facile method. The final product was characterized by X-ray diffractometer, transmission electron microscope, Fourier transform infrared spectrometer and vibration sample magnetometer. The preparation and adsorption conditions of the adsorbent were optimized. The adsorbent prepared maintaining volume ratio of tetraethylorthosilicate to hexadecyltrimethoxysilane at 1:0.5 and their total volume at 1100 μL exhibited high adsorption capacity. The optimum pH value for the adsorption experiments was 11.00. The adsorption behavior of Rhodamine 6G onto C₁₆/SiO₂-Fe₃O₄ NPs obeyed pseudo-second-order kinetic model and Langmuir isotherm. Thermodynamic data indicated that the adsorption process was spontaneous and exothermic. The adsorption capacity of the adsorbent could reach to 35.6 mg g⁻¹, owing to the hydrophobic attraction and the enhanced electrostatic attraction. The saturation magnetization of the magnetic adsorbent was 35 emu g⁻¹, which ensured the magnetic separation after adsorption.     

Ultrasound-assisted adsorption of copper(II) ions on hazelnut shell activated carbon

The present study was aimed to removal of Cu(II) ions from aqueous solution by ultrasound-assisted adsorption onto the granular activated carbon obtained from hazelnut shells. The attention was focused on modeling the equilibrium and kinetics of Cu(II) adsorption onto the granular activated carbon. The granular activated carbon was prepared from ground dried hazelnut shells by simultaneous carbonization and activation by water steam at 950 °C for 2 h. Adsorption isotherm data were better fitted by the Langmuir model than the Freundlich model in both the absence and the presence of ultrasound. The maximum adsorption capacity of the adsorbent for Cu(II), calculated from the Langmuir isotherms, in the presence of ultrasound (3.77 mmol/g) is greater than that in the absence of ultrasound (3.14 mmol/g). The adsorption process in the absence and the presence of ultrasound obeyed to the pseudo second-order kinetics. The removal of Cu(II) ions was higher in the presence of ultrasound than in its absence, but ultrasound reduced the rate constant. The intraparticular diffusion model indicated that adsorption of Cu(II) ions on the granular activated carbon was diffusion controlled as well as that ultrasound promoted intraparticular diffusion.