Improvement of copper plating adhesion on silane modified PET film by ultrasonic-assisted electroless deposition

Copper thin film on silane modified poly(ethylene terephthalate) (PET) substrate was fabricated by ultrasonic-assisted electroless deposition. The composition and topography of copper plating PET films were characterized by scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD) and atomic force microscopy (AFM), respectively. Peel adhesion strength, as high as 16.7 N/cm, was achieved for the planting copper layer to the modified PET substrate with ultrasonic-assisted deposition; however, a relative low value as 11.9 N/cm was obtained for the sample without ultrasonic vibration by the same measurement. The electrical conductivity of Cu film was changed from 7.9 × 10⁴ to 2.1 × 10⁵ S/cm by using ultrasonic technique. Ultrasonic operation has the significant merits of fast deposition and formation of good membranes for electroless deposition of Cu on PET film.     

Fabrication of microelectrodes using flow layer-by-layer self assembly of gold nanoparticles

Microelectrodes to be used in microfluidic devices were prepared from the layer-by-layer flow deposition of gold nanoparticles. Pre-designed microfluidic channels were used as templates for the flow driven deposition of the nanoparticles in sequence with poly (diallyldimethyl amonium chloride) (PDADMAC). The electrical resistivity of the gold nanoparticle assembly was found to be strongly dependant on the concentration of sodium citrate used in the gold nanoparticle synthesis. As the electrical properties of the film changed from insulating to conducting when decreasing the citrate concentration, a 4 point probe setup was used to measure the resistivity of the film. Near bulk conductivity (5.42 × 10⁻⁶ Ω cm) was achieved with only 10 layers of film. The thickness and morphology of the flow-printed multilayer microelectrode was characterized using atomic force microscopy (AFM) and a field emission scanning electron microscope (FE-SEM). To demonstrate its usefulness, the microelectrode assembly was then tested toward the detection of KCl in solution, having a concentration ranging from 1 to 20 mM using AC current detection in a simple setup. Good linearity and stability of the electrode confirmed that this method could be very convenient for the fabrication of microelectrodes for lab-on-chip applications.     

A green synthetic approach to graphene nanosheets for hydrogen adsorption

A green and facile strategy of preparing graphene by reducing exfoliated graphite oxide (GO) with glucose was developed in this study. The as-prepared samples were characterized by X-ray diffraction (XRD), Raman spectroscopy, Fourier transform infrared spectroscopy (FT-IR), Scanning electron microscopy (SEM), Transmission electron microscopy (TEM) and Atomic force microscopy (AFM). The characterization results indicated that the graphene sheets (GS) were of high quality with smooth surface, rich pore structure and few layer graphene. The samples have a BET specific surface area of 1205.8 m² g⁻¹ measured by N₂ adsorption at 77 K. The hydrogen storage capacity of 2.7 wt.% at 298 K and 25 bar demonstrated that the as-prepared graphene employing glucose as reductant is supposed to be a promising material with outstanding property for hydrogen storage.     

Multilayer Bi1.5Zn1.0Nb1.5O7/Ba0.6Sr0.4TiO3/Bi1.5Zn1.0Nb1.5O7 thin films for tunable microwave applications

Bi_1.5Zn_1.0Nb_1.5O₇/Ba_0.6Sr_0.4TiO₃/Bi_1.5Zn_1.0Nb_1.5O₇ tunable multilayer thin film has been fabricated by pulsed laser ablation and characterized. Phase composition and microstructure of multilayer films were characterized by X-ray diffraction, scanning electron microscopy (SEM) and atomic force microscopy (AFM). The film has very smooth surface with RMS roughness of 1.5-2 nm and grain size of 100-150 nm. Total film thickness has been measure to be 375 nm. The BZN thin films at 300 K, on Pt(1 1 1)/SiO₂/Si substrate showed zero-field dielectric constant of 105 and dielectric loss tangent of 0.002 at frequency of 0.1 MHz. Thin films annealed at 700 °C shows the dielectric tunability of 18% with biasing field 500 kV/cm at 0.1 MHz. The multilayer thin film shows nonferroelectric behavior at room temperature. The good physical and electrical properties of multilayer thin films make them promising candidate for tunable microwave device applications.     

Novel chemical synthetic route and characterization of zinc selenide thin films

Zinc selenide (ZnSe) thin film have been deposited using chemical bath method on non-conducting glass substrate in a tartarate bath containing zinc sulfate, ammonia, hydrazine hydrate, sodium selenosulfate in an aqueous alkaline medium at 333 K. The deposition parameter of the ZnSe thin film is interpreted in the present investigation. The films were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), optical absorption, electrical measurements, atomic absorption spectroscopy (AAS). The ZnSe thin layers grown with polycrystalline zinc blende system along with some amorphous phase present in ZnSe film. The direct optical band gap ‘E_g’ for the film was found to be 2.81 eV and electrical conductivity in the order of 10⁻⁸(Ω cm)⁻¹ with n-type conduction mechanism.     

Preparation and electrochemical properties of LiFePO<Subscript>4</Subscript>/graphene composites from tailoring graphene oxides

LiFePO₄/graphene composites have been prepared by using tailoring graphene oxide (GO) nanosheets as precursors. The structure and electrochemical properties of the composites were investigated by X-ray diffraction (XRD), atomic force microscopy (AFM), scanning electron microscopy (SEM), Raman microscopy, and a variety of electrochemical testing techniques. The decrease in graphene size reduces the contact resistance between activated materials, and enhances the lithium-ion transport in LiFePO₄/graphene composites. With low weight fractions of small-size graphene sheets, the composites show better electrochemical performance than those with large size graphene sheets.     

Synthesis, characterization of chemically deposited indium selenide thin films at room temperature

Polycrystalline In₂Se₃ semiconducting thin films were prepared by using relatively simple chemical bath deposition method at room temperature by the reaction between indium chloride, tartaric acid, hydrazine hydrate and sodium selenosulphate in an aqueous alkaline medium. Various preparative conditions of thin film deposition are outlined. The as grown films were found to be transparent, uniform, well adherent and red in color. The films were characterized using X-ray diffraction (XRD), scanning electron microscopy, atomic absorption spectroscopy and energy dispersive atomic X-ray diffraction (EDAX). The XRD analysis of the film showed the presence of polycrystalline nature with hexagonal crystal structure. SEM study revels that the grains are homogenous, without cracks or pinholes and well covers the glass substrate. The optical absorption and electrical conductivity was measured. The direct optical band gap value for the films was found to be of the order of 2.35 eV at room temperature and have specific electrical conductivity of the order of 10⁻² (Ω cm)⁻¹ showing n-type conduction mechanism. The utility of the adapted technique is discussed from the view-point of applications considering the optoelectric and structural data.     

Effects of poly(ethylene glycol) on electrical conductivity of poly(3,4-ethylenedioxythiophene)–poly(styrenesulfonic acid) film

A series of poly(3,4-ethylenedioxythiophene)–poly(styrenesulfonic acid) composite thin films with prescribed concentrations of poly(ethylene glycol) were prepared. The PEDOT–PSS pristine film and PEDOT–PSS/PEG films were studied using four-probe method, photoelectron spectroscopy and atomic force microscopy. The electrical conductivity of PEDOT–PSS/PEG hybrid films was found to be enhanced compared to the PEDOT–PSS pristine film, depending on the PEG concentration and molecular weight. XPS analysis and AFM results showed that PEG induces the phase separation between the PEDOT–PSS conducting particles and the excessive PSSNa shell. Simultaneously PEG may form hydrogen bond with sulfonic groups of PSSH, and hence weaken the electrostatic interactions between PEDOT cationic chains and PSS anionic chains. These resulted in the creation of a better conduction pathway among PEDOT–PSS particles, attributed to the improvement of conductivity.     

Nanosized multilayer films with concurrent photochromism and electrochromism based on Dawson-type polyoxometalate

An inorganic-organic composite multilayer film constructed of poly(vinyl alcohol) (PVA) with Dawson-type phosphotungstate anion [P₂W₁₈O₆₂]⁶⁻ (P₂W₁₈) and poly(allylamine hydrochloride) (PAH) were fabricated on quartz, ITO, silicon and CaF₂ substrates by a layer-by-layer self-assembly method. The film was provided with concurrent photochromism and electrochromism. IR spectra showed that the structure of the PVA was fully maintained in the multilayer film. And their photochromic and electrochromic properties were investigated by UV-vis spectra, cyclic voltammetry (CV), chronoamperometry (CA) measurement and X-ray photoelectron spectra (XPS). Atomic force microscopy (AFM) was used to investigate the surface topography. This study provides a new route to explore the possibility of application to polyoxometalate-based hybrid inorganic-organic materials.     

Effect of temperature on pulsed laser deposition of HgCdTe films

HgCdTe thin films have been deposited on Si(1 1 1) substrates at different substrate temperatures by pulsed laser deposition (PLD). An Nd:YAG pulsed laser with a wavelength of 1064 nm was used as laser source. The influences of the substrate temperature on the crystalline quality, surface morphology and composition of HgCdTe thin films were characterized by X-ray diffraction (XRD), selected area electron diffraction (SAED), atomic force microscopy (AFM) and energy dispersive X-ray spectroscopy (EDS). The results show that in our experimental conditions, the HgCdTe thin films deposited at 200 °C have the best quality. When the substrate temperature is over 250 °C, the HgCdTe film becomes thermodynamically unstable and the quality of the film is degraded.     

Synthesis of aqueous dispersion of graphenes via reduction of graphite oxide in the solution of conductive polymer

Graphene sheets were produced by chemical reduction of graphite oxides in the solution of ionic conductive polymer, Nafion. The obtained graphene, coated with Nafion, can be re-dispersed in water, and readily forms stable dispersed state. The polymer-coated graphene had been characterized by FT-IR spectroscopy, UV-vis and X-ray photoelectron spectroscopy (XPS). The PEDOT film with Nafion-coated graphene increased significantly from 0.25 S/cm for pure PEDOT film and reached 12 S/cm. Further, the films of PEDOT doped Nafion-coated graphene had also higher conductivities compared to films doped PSS-coated graphene.     

Preparation of Co3O4 nanoplate/graphene sheet composites and their synergistic electrochemical performance

Co₃O₄ nanoplate/graphene sheet composites were prepared through a two-step synthetic method. The composite material as prepared was characterized using X-ray diffraction, scanning electron microscopy, transmission electron microscopy, and energy-dispersive X-ray spectroscopy. The platelet-like morphology of Co₃O₄ leads to a layer-by-layer-assembled structure of the composites and a good dispersion of Co₃O₄ nanoplates on the surface of graphene sheets. The electrochemical characteristics indicate that the specific capacitance of the composites is 337.8 F?g^?1 in comparison with the specific capacitance of 204.4 F?g^?1 without graphene sheets. Meanwhile, the composites have an excellent rate capability and cycle performance. The results show that the unique microstructure of the composites enhances the electrochemical capacitive performance of Co₃O₄ nanoplates due to the three-dimensional network of graphene sheets for electron transport increasing electric conductivity of the electrode and providing unobstructed pathways for ionic transport during the electrochemical reaction.     

Graphene oxide with improved electrical conductivity for supercapacitor electrodes

Predominant few-layer graphene (FLG) sheets of high electrical conductivity have been synthesized by a multi-step intercalation and reduction method. The electrical conductivity of the as-synthesized FLG is measured to be ∼3.2 × 10⁴ S m⁻¹, comparable to that of pristine graphite. Scanning electron microscopy (SEM), transmission electron microscopy (TEM) and Raman analysis reveal that the as-synthesized FLG sheets have large areas with single and double layers. The specific capacitance of 180 F g⁻¹ is obtained for the FLG in a 1 M Na₂SO₄ aqueous electrolyte by integrating the cyclic voltammogram. The good capacitive behavior of the FLG is very promising for the application for next-generation high-performance electrochemical supercapacitors.     

Surface and interfacial structural characterization of MBE grown Si/Ge multilayers

Si/Ge multilayer structures have been grown by solid source molecular beam epitaxy (MBE) on Si (1 1 1) and (1 0 0) substrates and were characterized by high-resolution X-ray diffraction (XRD), atomic force microscopy (AFM), high-depth-resolution secondary ion mass spectroscopy (SIMS) and cross-section high-resolution transmission electron microscopy (HRTEM). A reasonably good agreement has been obtained for layer thickness, interfacial structure and diffusion between SIMS and HRTEM measurements. Epitaxial growth and crystalline nature of the individual layer have been probed using cross-sectional HRTEM and XRD measurements. Surface and interface morphological studies by AFM and HRTEM show island-like growth of both Si and Ge nanostructures.     

Multi-layer structures including zigzag sculptured thin films for corrosion protection of AISI 304 stainless steel

To increase corrosion resistance of the sample,its electrical impedance must be increased.Due to the fact that electrical impedance depends on elements such as electrical resistance,capacitance,and inductance,by increasing the electrical resistance,reducing the capacitance and inductance,electrical impedance and corrosion resistance can be increased.Based on the fact that these elements depend on the type of material and the geometry of the material,multilayer structures with different geometries are proposed.For this purpose,conventional multilayer thin films,multilayer thin film including zigzag structure(zigzag 1)and multilayer thin film including double zigzag structure(zigzag 2)of manganese nitride are considered to protect AISI 304 stainless steel against corrosion in salt solution.These multilayer coatings including zigzag structures are prepared by alternately using the conventional deposition of thin film and glancing angle deposition method.After deposition,the samples are placed in a furnace under nitrogen flux for nitriding.The cross sections of the structures are observed by field emission scanning electron microscopy(FESEM).Atomic force microscope(AFM)is used to make surface analyses of the samples.The results show that the multilayer thin films including zigzag structures have smaller grains than conventional multilayer thin films,and the zigzag 2 structure has the smaller grain than the other two samples,which is attributed to the effect of shadowing and porosity on the oblique angle deposition method.Crystallography structures of the samples are studied by using x-ray diffraction(XRD)pattern and the results show that nitride phase formation in zigzag 2 structure is better than that in zigzag 1 structure and conventional multilayer thin film.To investigate the corrosion resistances of the structures,electrochemical impedance spectroscopy(EIS)and potentiodynamic polarization tests are performed.The results reveal that the multilayer thin films with zigzag structures have better corrosion protection than the conventional multilayer thin films,and the zigzag structure 2 has the smallest corrosion current and the highest corrosion resistance.The electrical impedances of the samples are investigated by simulating equivalent circuits.The high corrosion resistance of zigzag 2 structure as compared with conventional multilayer structure and zigzag 1 structure,is attributed to the high electrical impedance of the structure due to its small capacitance and high electrical resistance.Finally,the surfaces of corroded samples are observed by scanning electron microscope(SEM).     

Deposition of ZnO multilayer on LiNbO3 single crystals by DC-magnetron sputtering

Zinc oxide (ZnO) thin films were deposited on LiNbO₃ (LN) single crystals with 200 nm thicknesses by three different ways, where coating of zinc (Zn) film was followed by thermal oxidation for four, two, and one steps with 50, 100, and 200 nm thicknesses repeatedly. Sample, which was produced at 4-step of deposition and oxidation of Zn layer, showed high transmittance and low structural defect due to a lower photoluminescence intensity and Urbach energy. Average grain size in X-ray diffraction (XRD), scanning electron microscopy (SEM) micrograph, and atomic force microscopy (AFM) images for multilayer of ZnO was lower than monolayer of ZnO thin films. Applying multilayer coating technique leads to decrease of surface roughness and scattering on light on surface and fabrication of LiNbO₃ waveguides with lower optical loss.     

Deposition of aluminum nitride thin film on Si(1 1 1) by KrF excimer laser and its characterizations

We present the deposition of aluminum nitride (AlN) thin film by KrF excimer laser sputtering and the study of the effects of substrate temperature and laser fluences. Deposition rate of AlN thin film at 0.3 Å/pulse has been achieved with laser fluence of 1500 mJ/cm² and at substrate temperature of 250 K, and this shows the enhancement of the deposition rate at low substrate temperature. Surface morphology of the deposited films is characterized by atomic force microscopy (AFM). In addition, the electrical performance of the MIS devices with AlN thin films prepared in this experiment has been characterized.     

Thin films of molecular materials synthesized from C32H20N10M (M = Co, Pb, Fe): Film formation, electrical and optical properties

In this work, the synthesis of molecular materials formed from metallic phthalocyanines and 1,4-phenylenediamine is reported. The powder and thin film (∼80-115 nm thickness) samples of the synthesized materials, deposited by vacuum thermal evaporation, show the same intra-molecular bonds in the IR spectroscopy studies, which suggests that the thermal evaporation process does not alter these bonds. The morphology of the deposited films was studied using scanning electron microscopy (SEM) and atomic force microscopy (AFM) and their optical and electrical properties were studied as well. The optical parameters have been investigated using spectrophotometric measurements of transmittance in the wavelength range 200-1200 nm. The absorption spectra recorded in the UV-vis region for the deposited samples showed two bands, namely the Q and Soret bands. The optical activation energy was calculated and found to be 3.41 eV for the material with cobalt, 3.34 eV for the material including lead and 3.5 eV for the material with iron. The effect of temperature on conductivity was measured for the thin films and the corresponding conduction processes are discussed in this work.     

Immobilization of immunoglobulin G in a highly oriented manner on a protein-A terminated multilayer system

In this study, we have fabricated a multilayer system consisting of 3-glycidoxypropyldimethylmethoxysilane (GPDS), poly(dimethylsiloxane) bis 3-aminopropyl terminated (PDMS) and protein-A on a silicon wafer surface for oriented immobilization of immunoglobilin G (IgG). The multilayer system with a different component in each layer was characterized by ellipsometry, contact-angle goniometer, X-ray photoelectron spectroscopy (XPS) and atomic force microscopy (AFM) and fluorescence microscopy. The epoxy-terminated monolayer was formed by the chemisorption of GPDS molecules on the hydroxylated silicon surface. The PDMS film about 4.5 nm thick was produced on the GPDS-monolayer by the chemical reaction between the amine groups at the end of PDMS chain and the epoxy groups of GPDS molecules. By introducing the PDMS chains, the hydrophilic character of GPDS-monolayer decreased. Study of the time dependence of polymer grafting showed that the chemisorption of GPDS is fast, whereas at least 16 h is needed to generate the homogeneous PDMS layer. For immobilization of IgG molecules in a highly oriented manner, protein-A molecules were first chemically bound to an ultrathin (∼4.5 nm) PDMS reactive polymer layer and later used to capture IgG. It was shown that the existence of protein-A in the multilayer system has a strong influence on the binding properties of IgG not only in the efficiency of binding, but also in its specificity. In conclusion, the multilayer system with protein-A has the potential to be further developed into an efficient immunoassay protein chip.     

Fabrication and Characterization of Ultrathin Graphene Oxide/Poly(Vinyl Alcohol) Composite Films via Layer-by-Layer Assembly

Novel multilayer ultrathin films comprised of graphene oxide (GO) and poly(vinyl alcohol) (PVA) were fabricated through a layer-by-layer (LBL) assembly technique. GO could self-assemble onto quartz substrates alternately with PVA via hydrogen-bonding interactions. X-ray diffraction, atomic force microscopy, and transmission electron microscopy analysis revealed that GO was exfoliated to monolayers. The ultrathin films, with PVA/GO multilayer structures fabricated by LBL assembly, were characterized by ultraviolet-visible spectroscopy and X-ray diffraction analysis, confirming that the assembly of the multilayer films was quantitative and reproducible.