Oxygen flux influence on the morphological, structural and optical properties of Zn1−xMgxO thin films grown by plasma-assisted molecular beam epitaxy

The Zn_1−xMg_xO thin films were grown on Al₂O₃ substrate with various O₂ flow rates by plasma-assisted molecular beam epitaxy (P-MBE). The growth conditions were optimized by the characterizations of morphology, structural and optical properties. The Mg content of the Zn_1−xMg_xO thin film increases monotonously with decreasing the oxygen flux. X-ray diffractometer (XRD) measurements show that all the thin films are preferred (0 0 2) orientated. By transmittance and absorption measurements, it was found that the band gap of the film decreases gradually with increasing oxygen flow rate. The surface morphology dependent on the oxygen flow rate was also studied by field emission scanning electron microscopy (FE-SEM). The surface roughness became significant with increasing oxygen flow rate, and the nanostructures were formed at the larger flow rate. The relationship between the morphology and the oxygen flow rate of Zn_1−xMg_xO films was discussed.     

Properties of MgxZn1−xO thin films sputtered in different gases

Mg_xZn_1−xO alloy films were prepared on sapphire substrates using Ar and N₂ as the sputtering gases. The effect of the sputtering gas on the structural, optical and electrical properties of the Mg_xZn_1−xO films was studied. By using N₂ as the sputtering gas, the Mg_xZn_1−xO film shows p-type conductivity and the band gap is larger than that employing Ar as the sputtering gas. The reason for this phenomenon is thought to be related to the reaction between N-O or N-Zn, and the N-doping.     

Preparation and properties of composite ceramic coating containing Al2O3–ZrO2–Y2O3 on AZ91D magnesium alloy by plasma electrolytic oxidation

A composite ceramic coating containing Al₂O₃–ZrO₂–Y₂O₃ was successfully prepared on AZ91D magnesium alloy by plasma electrolytic oxidation (PEO) technique in an alkaline aluminate electrolyte. The morphology, elemental and phase composition, corrosion behavior and thermal stability of the uncoated and coated samples were studied by environmental scanning electron microscopy (ESEM), energy dispersive X-ray spectrometer (EDS), X-ray diffractometer (XRD), electrochemical corrosion test, high temperature oxidation test and thermal shock test. The results showed that the composite ceramic coating was composed of Al₂O₃, c-ZrO₂, t-ZrO₂, Y₂O₃ and some magnesium compounds, such as MgO, MgF₂ and MgAl₂O₄. After PEO treatment, the corrosion potential of AZ91D alloy was increased and the corrosion current density was significantly reduced. Besides, the coated magnesium alloys also showed excellent high temperature oxidation resistance and thermal shock resistance at 500 °C environment.     

First-principles calculations of structural,electronic and thermal properties of Zn1−x Mg x S ternary alloys

Structural, electronic and thermal properties of Zn_1?x Mg _x S ternary alloys are studied by using the full potential-linearized augmented plane wave method (FP-LAPW) within the density functional theory (DFT). The Wu-Cohen generalized gradient approximation (WC-GGA) is used in this approach for the exchangecorrelation potential. Moreover, the modified Becke-Johnson approximation (mBJ) is adopted for band structure calculations. The dependence of the lattice constant, bulk modulus and band gap on the composition x showed that the first exhibits a small deviation from the Vegard’s law, whereas, a marginal deviation of the second from linear concentration dependence (LCD). The bowing of the fundamental gap versus composition predicted by our calculations agrees well with the available theoretical data. The microscopic origins of the gap bowing are explained by using the approach of Zunger and co-workers. Thermal effects on some macroscopic properties of Zn_1?x Mg _x S alloys are also investigated using the quasi-harmonic Debye model, in which the phononic effects are considered. As, this is the first quantitative theoretical prediction of the thermal properties of Zn_1?x Mg _x S alloys, no other calculated results and furthermore no experimental studies are available for comparison.     

Effects of niobium on thermal stability and corrosion behavior of glassy Cu-Zr-Al-Nb alloys

The corrosion behavior of Cu_95−xZr_xAl₅ (x=40, 42.5 and 45 at.%) in 1 N HCl, 3 mass% NaCl and 1 N H₂SO₄ solutions was studied. As Zr content increases, the corrosion resistance is slightly enhanced. In order to improve the corrosion resistance of the Cu-Zr-Al glassy alloy, Nb was selected to substitute Cu. Although the supercooled liquid region ΔT_x of the Cu-Zr-Al glassy alloys decreases with increasing Nb content, the alloys still retain high glass-forming ability and bulk glassy samples with 1.5 mm diameter can be obtained when up to 5 at.% Nb was added. It is found that the addition of Nb results in improvement of the corrosion resistance of the glassy Cu-Zr-Al alloys.     

Effect of substrate annealing on the quality of pulsed laser deposited Zn1−xMgxO thin films

The annealing effects of sapphire substrate before deposition on the quality of epitaxial Zn_1−xMg_xO thin films grown by pulsed laser deposition are reported. Our Experimental results indicate that the surface quality of Zn_1−xMg_xO thin films and hexagonal columnar growth is improved on the annealed sapphire substrate at high temperatures due to formation of atomic terraces on the substrate surface. The photoluminescence signals also increases with the increasing annealing temperature of the substrate.     

Yttrium ion implantation on the surface properties of magnesium

Owing to their excellent physical and mechanical properties, magnesium and its alloys are receiving more attention. However, their application has been limited to the high reactivity and the poor corrosion resistance. The aim of the study was to investigate the beneficial effects of ion-implanted yttrium using a MEVVA ion implanter on the surface properties of pure magnesium. Isothermal oxidation tests in pure O₂ at 673 and 773 K up to 90 min indicated that the oxidation resistance of magnesium had been significantly improved. Surface morphology of the oxide scale was analyzed using scanning electron microscope (SEM). Auger electron spectroscopy (AES) and X-ray diffraction (XRD) analyses indicated that the implanted layer was mainly composed of MgO and Y₂O₃, and the implanted layer with a duplex structure could decrease the inward diffusion of oxygen and reduce the outward diffusion of Mg²⁺, which led to improving the oxidation resistance of magnesium. Potentiodynamic polarization curves were used to evaluate the corrosion resistance of the implanted magnesium. The results show yttrium implantation could enhance the corrosion resistance of implanted magnesium compared with that of pure magnesium.     

射频磁控溅射法生长MgxZn1-xO薄膜的结构和光学特性

用射频磁控溅射法在80℃的衬底温度下制备出Mg_xZn_1-xO(0≤x ≤030)薄膜.x射线 衍射(XRD)结果表明，Mg_xZn_1-xO薄膜为单相六角纤锌矿结构， 没有形成任何显著 的MgO分离相，Mg_xZn_1-xO薄膜的择优取向平行于与衬底垂直的 c轴；c轴晶格常数随着Mg含量的增加逐渐减小.在Mg_xZn_1-xO薄膜的光透射谱中出现 锐利的吸收边，由透 射谱估算出Mg_xZn_1-xO薄膜的带隙宽度由332eV(x=0)线性地 增加到396eV(x=030). 关键词： xZn_1-xO薄膜')" href="#">Mg_xZn_1-xO薄膜 射频磁控溅射 Mg含量     

Size dependent effective band gap,optical absorption coefficients and refractive index changes in a wide ZnS/Zn1−xMgxS strained quantum well

Exciton binding energy of a confined heavy hole exciton is investigated in a Zn_1−xMg_xS/ZnS/Zn_1−xMg_xS single strained quantum well with the inclusion of size dependent dielectric function for various Mg content. The effects of interaction between the exciton and the longitudinal optical phonon are brought out. The effect of exciton is described by the effective potential between the electron and hole. The interband emission energy as a function of well width is calculated for various Mg concentration with and without the inclusion of dielectric confinement. Non-linear optical properties are carried out using the compact density matrix approach. The dependence of nonlinear optical processes on the well width is investigated for different Mg concentration. The linear, third order non-linear optical absorption coefficients values and the refractive index changes of the exciton are calculated for different concentration of magnesium content. The results show that the exciton binding energy is found to exceed LO phonon energy of ZnS for x>0.2 and the incorporation of magnesium ions and the effect of phonon have great influence on the optical properties of ZnS/Zn_1−xMg_xS quantum wells.     

Effect of Mg doping and substrate temperature on the properties of pulsed laser deposited epitaxial Zn1?xMgxO thin films

In this paper, we report on the pulsed laser deposition of epitaxial (0002) oriented Zn_1−x Mg _x O thin films onto (0001) sapphire substrate in O₂ ambient at different deposition temperatures. Pulsed laser deposited Zn_1−x Mg _x O films showed (0002) oriented hexagonal wurtzite structure up to 34% of Mg concentration. The bandgap of Zn_1−x Mg _x O thin films is successfully tuned from 3.3 to 4.2 eV by adjusting the Mg concentration x=0.0 to x=0.34. Pulsed laser deposited Zn_1−x Mg _x O thin films were characterized by XRD, AFM, SEM, PL and UV–VIS spectrometer. We have also studied the effect of deposition temperature on to the structure, surface morphology and optical properties of Zn_1−x Mg _x O thin films.     

Neutron crystal-field spectroscopy and susceptibility in TmxY1−xAl2

Inelastic neutron scattering due to crystalline electric field transitions is observed in Tm_0.25Y_0.75Al₂. The best fit of the theoretical cross section to experiment is obtained for the Lea, Leask and Wolf parameters W = (0.040 ± 0.005)meV and X = (0.50 ± 0.05). The extrapolation of the measured susceptibility of Tm_xY_1?xAl₂(x = 0.05, 0.15, 0.25)tox = 0 is in good agreement with theory when using the above parameters.     

Cu(In,Ga)Se2 superstrate-type solar cells with Zn1−xMgxO buffer layers

Superstrate-type Cu(In,Ga)Se₂ (CIGS) thin film solar cells were fabricated using Zn_1−xMg_xO buffer layers. Due to the diffusion of Cd into CIGS during the growth of the CIGS layer, the conventional buffer material of CdS is not suitable. ZnO is a good candidate because of higher thermal tolerance but the conduction band offset (CBO) of ZnO/CIGS is not appropriate. In this study, the Zn_1−xMg_xO buffer layers were used to fulfill both the requirements. The superstrate-type solar cells with a soda-lime glass/In₂O₃:Sn/Zn_1−xMg_xO/CIGS/Au structure were fabricated with different band gap energies of the Zn_1−xMg_xO layer. The CIGS layers [Ga/(In + Ga)∼0.25] were deposited by co-evaporation method. The substrate temperature during the CIGS deposition of 450 °C did not cause the intermixing of the Zn_1−xMg_xO and CIGS layers. The conversion efficiency of the cell with Zn_1−xMg_xO was higher than that with ZnO due to the improvement of open-circuit voltage and shunt resistance. The results well corresponded to the behavior of the adjustment of CBO, demonstrating that the usefulness of the Zn_1−xMg_xO layer for the CBO control in the superstrate-type CIGS solar cells.     

Structural and magnetic properties of rapidly solidified (Ce0.2Fe0.8)1-x Al x ribbons determined by X-ray diffraction and Mössbauer spectrometry

(Ce_0.2Fe_0.8)_1-x Al _x (0 x 0.9) ribbons have been prepared by planar flow casting under an He atmosphere with a linear velocity of 29 m s^-1. Analyses of the ribbons by X-ray diffraction and⁵⁷Fe Mössbauer spectrometry in the temperature range 4–300 K show that all the ribbons are crystalline. With increasingx, the observed phases are Ce(Fe, Al)₂, Ce₂(Fe, Al)₁₇, CeFe_4+y,Al_8-y and the single fcc aluminium phase. For the different phases, the line intensities of the Mössbauer spectra agree with previous results on the preferential substitution sites for aluminium. A coherent hyperfine parameters set was deduced from fitting spectra in the temperature range 4–300 K.     

Correlation between structural changes and luminescent properties of ZnMgS:Mn thin film phosphor with annealing temperature

With varying rapid thermal annealing temperature, luminescent properties of Zn_0.75Mg_0.25S:Mn thin film deposited by RF-magnetron sputtering technique were investigated. Although all samples were deposited from identical source composition, it was found that a main peak wavelength of photoluminescence of Zn_0.75Mg_0.25S:Mn depended on RTA temperatures and it shifted toward shorter wavelength upon the increase of RTA temperature. The same dependence of wavelength on RTA temperature was also observed in cathodoluminescence as well as electroluminescence measurements. It is noticeable that Zn_0.75Mg_0.25S:Mn thin film phosphor in this study showed more reddish emission than those of the previous studies.It was revealed that changes of the luminescent properties were originated from structural changes in Zn_0.75Mg_0.25S:Mn thin film phosphor from cubic to hexagonal phases using X-ray pole figure mapping, and the growing up of hexagonal phase mainly caused cracks and porous morphology on the surface of thin films. It is suggested that the phase transition would be the origin of luminescent property changes with respect to rapid thermal annealing temperature.     

石英玻璃衬底上纤锌矿Mg0.25Zn0.75O薄膜的结构及光学性能

Mg_xZn_1-xO材料是一种新型光电功能材料.采用溶胶凝胶法在石英玻璃上制备了Mg_0.25Zn_0.75O薄膜,理论结合实验研究了Mg_0.25Zn_0.75O薄膜的结构和光学性能.研究表明,石英玻璃衬底上Mg_0.25Zn_0.75O薄膜呈六方纤锌矿结构,薄膜均匀,平均粒径约为20nm.吸收光谱表明吸收带边始于3 关键词： 0.25Zn_0.75O薄膜')" href="#">Mg_0.25Zn_0.75O薄膜 溶胶凝胶法 石英玻璃衬底 紫外发光     

白宝石衬底上生长的MgxZn1-xO晶体薄膜的结构和光学性能

在白宝石（sapphire）衬底上低温外延生长出了Mg_xZn_1-xO晶体薄膜.x射线衍射（XRD）及能量色散x射线（EDX）分析表明，Mg_xZn_1-xO薄膜的晶体结构依赖于薄膜中Mg的组分x，随着Mg组分的增大，Mg_xZn_1-xO薄膜的结构从与ZnO晶体一致的六方结构转变为与MgO晶体一致的立方结构.对Mg_xZn_1-xO薄膜的紫外透 关键词： 电子束蒸发反应 xZn_1-xO晶体薄膜')" href="#">Mg_xZn_1-xO晶体薄膜 结构和光学性能     

Observation of optical properties related to room-temperature ferromagnetism in co-sputtered Zn1−xCoxO thin films

We report on the analysis of optical transmittance spectra and the resulting ferromagnetic characteristics of sputtered Zn_1−xCo_xO films. Zn_1−xCo_xO films were prepared on (0001)-oriented Al₂O₃ substrates by the radio-frequency (rf) magnetron co-sputtering method. The XRD results showed that the crystallinity of films was properly maintained up to x=0.30 and no second phase peaks were detected up to x=0.40. The transmittance spectra showed both the increase of the absorption band intensity and the red shift of the absorption peak as well as the band edge with increasing x. We have proved experimentally that these changes depend on Co concentration. These optical properties suggest that sp-d exchange interactions and typical d-d transitions become activated with increasing x, which leads to the enhancement of ferromagnetic properties in Zn_1−xCo_xO films as shown in the AGM results. Therefore, it is concluded that the ferromagnetism derives from the substitution of Co²⁺ for Zn²⁺ without changing the wurtzite structure.     

Ternary alloys CdyZn1 ? yO and MgxZn1 ? xO as materials for optoelectronics

Thin films of Cd _y Zn_{1 − y} O and Mg _x Zn_{1 − x} O (y = 0−0.35, x = 0−0.45) ternary alloys have been grown by pulsed laser deposition onto sapphire substrates. The record solubility limits of Cd (y = 0.3) and Mg (x = 0.35) have been achieved in hexagonal zinc oxide. The mismatch of the lattice parameters a of Cd_0.2Zn_0.8O and Mg_0.35Zn_0.65O does not exceed 1%; in this case, the band gap discontinuity is 1.3 eV. The surface roughness of the films does not exceed 2.5 nm at x = 0−0.27 and y = 0−0.20.     

Growth of non-polar Zn1−x Mg x O thin films with different Mg contents on r-plane sapphire substrates by plasma-assisted molecular beam epitaxy

We report the growth and characterization of a series of non-polar Zn_1?x Mg _x O thin films with different Mg contents, which have been prepared on r-plane sapphire substrates by plasma-assisted molecular beam epitaxy. Structural properties are anisotropic and surfaces of films show stripes running along the c-axis direction. The films exhibit atomically smooth surface with the minimal root mean square surface roughness of 0.36 nm. Non-polar Zn_1?x Mg _x O thin film is much easier to obtain pure a-plane single crystal orientation when Mg content is high. The quality of the non-polar Zn_1?x Mg _x O thin films is evidenced by X-ray diffraction (XRD) rocking curves full-width at half-maximum of 1,350 arcsec for the ( \( 11\overline{2} 0 \) ) reflection and 1,760 arcsec for the ( \( 10\overline{1} 1 \) ) reflection, respectively. Room temperature photoluminescence peak shifts monotonously from 3.29 to 3.56 eV as Mg content increases from 0 to 0.13. Alloying with Mg is found to widen the bandgap energy of the ZnO.