Fabrication of nanostructures by selective growth of C60 and Si on Si(1 1 1) substrate

Using two types of selective growth, selective C₆₀ growth and selective Si growth, on a common Si(1 1 1) substrate, an array of C₆₀ nanoribbons with controlled values of width and thickness is fabricated. On a surface that has Si(1 1 1)√3 × √3R30°-Ag (referred to as Si(1 1 1)√3-Ag hereafter) and bare Si(1 1 1) regions at the same time, the preferential growth of C₆₀ multilayered film is recognized on the Si(1 1 1)√3-Ag region. The growth of Si selectively occurs on a bare Si(1 1 1) region if the substrate surface has C₆₀-adsorbed and bare Si(1 1 1) regions at the same time. As a demonstration of the use of these selective growths, we fabricate an array of well-isolated C₆₀ nanoribbons, which show a well-ordered molecular arrangement and have sizes of about 40 nm in widths and 3-4 nm in thicknesses.     

Bulk and surface properties of spinel Co3O4 by density functional calculations

DFT calculations are employed to bulk and surface properties of spinel oxide Co₃O₄. The bulk magnetic structure is calculated to be antiferromagnetic, with a Co²⁺ moment of 2.631 μ_B in the antiferromagnetic state. There are three predicted electron transitions O(2p) → Co²⁺(t_2g) of 2.2 eV, O(2p) → Co³⁺(e_g) of 2.9 eV and Co³⁺(t_2g) → Co²⁺(t_2g) of 3.3 eV, and the former two transitions are close to the corresponding experimental values 2.8 and 2.4 eV. The naturally occurring Co₃O₄ (1 1 0) and (1 1 1) surfaces were considered for surface calculations. For ideal Co₃O₄ (1 1 0) surfaces, the surface relaxations are not significant, while for ideal Co₃O₄ (1 1 1) surfaces the relaxation of Co²⁺ cations in the tetrahedral sites is drastic, which agrees with the experiment observation. The stability over different oxygen environments for possible ideal and defect surface terminations were explored.     

Growth of silver structures on silicon surfaces observed in vivo by scanning tunneling microscopy

Early stages of growth of silver thin films on oriented silicon surfaces Si(1 0 0)2 × 1 and Si(1 1 1)7 × 7 were studied directly during deposition at room temperature by the scanning tunneling microscopy. Single Ag atoms deposited on the Si(1 0 0)2 × 1 surface diffuse too fast on the surface to be imaged by the microscope. Nucleation on C-type defects of the Si(1 0 0)2 × 1 reconstruction has been observed. During further growth, the defects represent stable terminations of silver chains. Ag nanoclusters growing on the Si(1 1 1)7 × 7 surface have been studied as a system with low diffusivity at room temperature. On this surface, presence of effective interaction between Ag clusters and individual Ag atoms in neighboring cells of the reconstruction has been identified. The interaction results in lowering the barrier for Ag atom hopping to an adjacent unit cell occupied by an Ag cluster. Unique possibilities arising from scanning the surface directly during growth are demonstrated.     

Molecular dynamics simulation of CH3 interaction with Si(1 0 0) surface

Molecular dynamics simulations of the CH₃ interaction with Si(1 0 0) were performed using the Tersoff-Brenner potential. The H/C ratio obtained from the simulations is in agreement with available experimental data. The results show that H atoms preferentially react with Si. SiH is the dominant form of SiH_x generated. The amount of hydrogen that reacts with silicon is essentially energy-independent. H atoms do not react with adsorbed carbon atoms. The presence of C-H bonds on the surface is due to molecular adsorption.     

A density functional theory study of ethylene adsorption on Ni10(1 1 1), Ni13(1 0 0) and Ni10(1 1 0) surface cluster models and Ni13 nanocluster

Ethylene adsorption was studied by use of DFT/B3LYP with basis set 6-31G(d,p) in Gaussian’03 software. It was found that ethylene has adsorbed molecularly on all clusters with π adsorption mode. Relative energy values were calculated to be −50.86 kcal/mol, −20.48 kcal/mol, −32.44 kcal/mol and −39.27 kcal/mol for Ni₁₃ nanocluster, Ni₁₀(1 1 1), Ni₁₃(1 0 0) and Ni₁₀(1 1 0) surface cluster models, respectively. Ethylene adsorption energy is inversely proportional to Ni coordination number when Ni₁₀(1 1 1), Ni₁₃(1 0 0) and Ni₁₀(1 1 0) cluster models and Ni₁₃ nanocluster are compared with each other.     

Effects of electronic confinement and substrate on the low-temperature growth of Pb islands on Si(1 0 0)-2 × 1 surfaces

The growth of Pb films on the Si(1 0 0)-2 × 1 surface has been investigated at low temperature using scanning tunneling microscopy. Although the orientation of the substrate is (1 0 0), flat-top Pb islands with (1 1 1) surface can be observed. The island thickness is confined within four to nine atomic layers at low coverage. Among these islands, those with a thickness of six layers are most abundant. Quantum-well states in Pb(1 1 1) islands of different thickness are acquired by scanning tunneling spectroscopy. They are found to be identical to those taken on the Pb(1 1 1) islands grown on the Si(1 1 1)7 × 7 surface. Besides Pb(1 1 1) islands, two additional types of Pb islands are formed: rectangular flat-top Pb(1 0 0) islands and rectangular three-dimensional (3D) Pb islands, and both their orientations rotate by 90° from a terrace to the adjacent one. This phenomenon implies that the structures of Pb(1 0 0) and 3D islands are influenced by the Si(1 0 0)-2 × 1 substrate.     

Intramolecular structures of C60 and C84 molecules on Si(1 1 1)-7 × 7 surfaces by scanning tunneling microscopy

The intramolecular features of carbon 60 and carbon 84 molecules on Si(1 1 1)-7 × 7 surfaces were studied under a UHV-scanning tunneling microscope. Carbon molecules preferentially appear in faulted halves, rather than in unfaulted halves and corner holes; they are embedded in silicon substrates. The orientation and details of the structure of carbon molecules are determined by applying various sample biases to the silicon substrate. As compared with other fullerenes, a bright pentagonal ring with nebulous clusters which represents the cage structure is clearly observed on top of carbon 60 molecules. The bright stripes associated with partitioned curves which depict eight features of asymmetrical C₈₄ molecules are also investigated on Si(1 1 1)-7 × 7 surfaces. The orientations and possible configurations of C₆₀ and C₈₄ are considered in this work. The energy differences for various features of C₆₀ and C₈₄ molecules are estimated and discussed. The corresponding models with respect to each intramolecular feature are proposed and compared with recent theoretical calculation.     

Adsorption of water on thin V2O3(0 0 0 1) films

V₂O₃(0 0 0 1) films have been grown epitaxially on Au(1 1 1) and W(1 1 0). Under typical UHV conditions these films are terminated by a layer of vanadyl groups as has been shown previously [A.-C. Dupuis, M. Abu Haija, B. Richter, H. Kuhlenbeck, H.-J. Freund, V₂O₃(0 0 0 1) on Au(1 1 1) and W(1 1 0): growth, termination and electronic structure, Surf. Sci. 539 (2003) 99]. Electron irradiation may remove the oxygen atoms of this layer. H₂O adsorption on the vanadyl terminated surface and on the reduced surface has been studied with thermal desorption spectroscopy (TDS), vibrational spectroscopy (IRAS) and electron spectroscopy (XPS) using light from the BESSY II electron storage ring in Berlin. It is shown that water molecules interact only weakly with the vanadyl terminated surface: water is adsorbed molecularly and desorbs below room temperature. On the reduced surface water partially dissociates and forms a layer of hydroxyl groups which may be detected on the surface up to T ∼ 600 K. Below ∼330 K also co-adsorbed molecular water is detected. The water dissociation products desorb as molecular water which means that they recombine before desorption. No sign of surface re-oxidation could be detected after desorption, indicating that the dissociation products desorb completely.     

NH3 on Si(0 0 1): Can Gaussian cluster and planewave slab models agree on energetics?

We critically evaluate the use of cluster and periodic slab models in describing the NH₃/Si(0 0 1) molecule-surface reaction system. We show that considerable discrepancies in the relative adsorbate energetics originate in the limitations of the small cluster and slab models commonly used. These limitations in turn are the consequence of the balance that must be struck between the competing demands of cluster/slab size, basis set size and exchange-correlation model. This leads us to consider “cluster compound models” in which the results of several smaller calculations (separately probing the effects of cluster/slab size, basis set size and exchange-correlation model) are combined to estimate the energy of a converged model.     

DFT study of NH3 dissociation on Si(1 1 1)-7 × 7. The role of intermolecular interactions

The adsorption of NH₃ molecule on the Si(1 1 1)-7 × 7 surface modelled with a cluster has been studied using density functional theory (DFT). The results indicate the existence of a precursor state for the non-dissociative chemisorption. The active site for the molecular chemisorption is the adatom; while the NH₃ molecule adsorbs on the Si restatom via this preadsorbed state, the adsorption on the Si adatom is produced practically without an energy barrier. The ammonia adsorption on the adatom induces an electron transfer from the dangling bond of this atom to the dangling bond of the adjacent Si restatom, hindering this site for the adsorption of a second NH₃ incoming molecule. However, this second molecule links strongly by means of two H-bonds. The dissociative chemisorption process was studied considering one and two ammonia molecules. For the dissociation of a lonely NH₃ molecule an energy barrier of ∼0.3 eV was calculated, yielding NH₂ on the adatom and H on the restatom. When two molecules are adsorbed, the NH₃-NH₃ interaction yields the weakening of a N-H bond of the ammonia molecule adsorbed closer the Si surface. As a consequence, the dissociation barrier practically disappears. Thus, the presence of a second NH₃ molecule at the adatom-restatom pair of the Si(1 1 1)-7 × 7 surface makes the dissociative reaction self-assisted, the total adsorption process elapsing with a negligible activation barrier (less than 0.01 eV).     

Evolution of Si0.8Ge0.2 quantum dots during Si encapsulation

Surface structure, determined by scanning tunneling microscopy (STM), surface morphology, determined by atomic force microscopy (AFM), and surface composition, determined by X-ray photoelectron spectroscopy (XPS) of 20.0 nm Si_0.8Ge_0.2 quantum dots formed at 800 °C and encapsulated with 0-10 nm of Si at 500 °C and 800 °C are presented. It is observed that the quantum dot surface morphology changes during the Si encapsulation at 800 °C by the smoothing of the quantum dots. The height of the quantum dots decreases faster than can be accounted for from the amount of Si deposited, indicating that there is movement of material out of the quantum dots during the encapsulation process. Encapsulation at 500 °C results in a retention of the quantum dot surface morphology with increased Ge segregation compared to Si encapsulation at 800 °C. We conclude that the changing surface morphology at 800 °C is not the result of Ge segregation but due to intermixing resulting from the tensile strain of Si depositing on SiGe.     

Configuration of pentacene (C22H14) films on Si(1 0 0)-2 × 1 studied by NEXAFS

Pentacene films on Si(1 0 0)-(2 × 1) surface at 300 K were investigated using near edge X-ray absorption fine structure (NEXAFS) at the carbon K-edge. NEXAFS spectra show that pentacene molecules are chemisorbed on the Si(1 0 0)-(2 × 1) surface for monolayer with flat-laying and predominantly physisorbed on the Si(1 0 0)-(2 × 1) surface for multilayer films with an upright molecular orientation. Absorption angle of pentacene molecules were measured through π^∗ transition. The angles between the double bond and the silicon surface were 35-55°, 65° and 76° at monolayer, 24 and 48 nm pentacene deposited on the Si(1 0 0) surface, respectively. We observed that the intermediate flat-laying phase is favored for monolayer coverage, while the films of molecules standing perpendicular to the Si(1 0 0) surface are favored for multilayer coverage.     

Correlation between structural and mechanical properties of PbTiO3 thin films grown by pulsed-laser deposition

Tetragonal lead titanate (PbTiO₃, PT) thin films are grown on (1 0 0) MgO substrate by pulsed-laser deposition (PLD) for expected applications in integrated optics. The realisation of outstanding and reliable devices into integrated circuits requires sufficient mechanical resistance despite that the obtained PT films display interesting waveguiding properties associated with low optical losses. Two mechanical properties characteristic of elasticity and hardness of PT films are studied. The elastic modulus (E or Young's modulus) and the hardness (H) are measured by the nanoindentation technique. These mechanical properties are correlated to the crystalline quality of PT/MgO thin films. The films show epitaxial relationship with the MgO substrate and the orientation of crystallites perpendicularly to the surface substrate may be the consequence of a growth process along c-axis, a-axis or both. Differences on curves plotting hardness and elastic modulus as a function of indentation depth are observed as the curves are less dispersed for the films mainly c-axis oriented.     

Spin-engineering in the Co75Fe25/Cu(1 1 0) system

We present results on the growth and magnetic anisotropies of Co₇₅Fe₂₅ films grown on a Cu(1 1 0) single crystal. Angular dependent MOKE measurements show a thickness dependent, in-plane rotation of the easy axis of magnetisation of up to 60° from the [0 0 1] direction (towards [−1 1 0]). For a film thickness of 5 ML, just greater than that required for the onset of ferromagnetism, uniaxial anisotropy is observed with the easy axis along the [0 0 1] direction. As the film thickness increases this is seen to rotate in-plane towards the [−1 1 0] direction as the contribution from the cubic anisotropy constant grows. At a film thickness of 9 ML there is predominantly cubic anisotropy and at 10 ML the easy axis is rotated to 150° with respect to the [1 −1 0] axis, where it is stabilised.     

Effect of oxygen pressure on microstructure and magnetic properties of strontium hexaferrite (SrFe12O19) film prepared by pulsed laser deposition

The effects of oxygen pressure during deposition on microstructure and magnetic properties of strontium hexaferrite (SrFe₁₂O₁₉) films grown on Si (100) substrate with Pt (111) underlayer by pulsed laser deposition have been investigated. X-ray diffraction pattern confirms that the films have c-axis perpendicular orientation. The c-axis dispersion (Δθ₅₀) increases and c-axis lattice parameter decreases with increasing oxygen pressure. The films have hexagonal shape grains with diameter of 150-250 nm as determined by atomic force microscopy. The coercivities in perpendicular direction are higher than those in in-plane direction, which shows the films have perpendicular magnetic anisotropy. The saturation magnetization and anisotropy field for the film deposited in oxygen pressure of 0.13 mbar are comparable to those of the bulk strontium hexaferrite. Higher oxygen pressure leads to the films having higher coercivity and squareness. The coercivity in perpendicular and in-plane directions of the film deposited in oxygen pressure of 0.13 mbar are 2520 Oe and 870 Oe, respectively.     

Low temperature adsorption of oxygen on reduced V2O3(0 0 0 1) surfaces

Well ordered V₂O₃(0 0 0 1) films were prepared on Au(1 1 1) and W(1 1 0) substrates. These films are terminated by a layer of vanadyl groups under typical UHV conditions. Reduction by electron bombardment may remove the oxygen atoms of the vanadyl layer, leading to a surface terminated by vanadium atoms. The interaction of oxygen with the reduced V₂O₃(0 0 0 1) surface has been studied in the temperature range from 80 to 610 K. Thermal desorption spectroscopy (TDS), infrared reflection absorption spectroscopy (IRAS), high resolution electron energy loss spectroscopy (HREELS), X-ray photoelectron spectroscopy (XPS), and density functional theory (DFT) were used to study the adsorbed oxygen species. Low temperature adsorption of oxygen on reduced V₂O₃(0 0 0 1) occurs both dissociatively and molecularly. At 90 K a negatively charged molecular oxygen species is observed. Upon annealing the adsorbed oxygen species dissociates, re-oxidizing the reduced surface by the formation of vanadyl species. Density functional theory was employed to calculate the structure and the vibrational frequencies of the O₂ species on the surface. Using both cluster and periodic models, the surface species could be identified as η²-peroxo () lying flat on surface, bonded to the surface vanadium atoms. Although the O-O vibrational normal mode involves motions almost parallel to the surface, it can be detected by infrared spectroscopy because it is connected with a change of the dipole moment perpendicular to the surface.     

Growth of (√3 × √3)-Ag and (1 1 1) oriented Ag islands on Ge/Si(1 1 1) surfaces

We have studied the growth of Ag on Ge/Si(1 1 1) substrates. The Ge/Si(1 1 1) substrates were prepared by depositing one monolayer (ML) of Ge on Si(1 1 1)-(7 × 7) surfaces. Following Ge deposition the reflection high energy electron diffraction (RHEED) pattern changed to a (1 × 1) pattern. Ge as well as Ag deposition was carried out at 550 °C. Ag deposition on Ge/Si(1 1 1) substrates up to 10 ML has shown a prominent (√3 × √3)-R30° RHEED pattern along with a streak structure from Ag(1 1 1) surface. Scanning electron microscopy (SEM) shows the formation of Ag islands along with a large fraction of open area, which presumably has the Ag-induced (√3 × √3)-R30° structure on the Ge/Si(1 1 1) surface. X-ray diffraction (XRD) experiments show the presence of only (1 1 1) peak of Ag indicating epitaxial growth of Ag on Ge/Si(1 1 1) surfaces. The possibility of growing a strain-tuned (tensile to compressive) Ag(1 1 1) layer on Ge/Si(1 1 1) substrates is discussed.     

Adsorption behaviors of V2O5 nanowires on binary mixed self-assembled monolayers

The adsorption behaviors of V₂O₅ nanowires on binary mixed self-assembled monolayers (SAMs) were investigated with variation of the mixing ratio of two differently terminated thiolates on Au. Hydroxyl-covered V₂O₅ nanowires showed a preferential adsorption on amine (NH₂)-terminated thiolates over methyl (CH₃)-terminated ones. However, on the binary mixed SAM of NH₂- and CH₃-terminated thiols, the adsorption behavior did not follow a simple expectation based upon the electrostatic interaction. The total number of adsorbed V₂O₅ nanowires increased with the mole fraction of NH₂-terminated thiolates up to χNH₂∼0.5, then it decreased with further increase of χNH₂. The height distribution of adsorbed nanowires showed that the relative portion of the agglomerated wires thicker than 3.5 nm to individual wires thinner than 3.5 nm increased up to χNH₂∼0.75 and then it decreased with further increase of χNH₂. The dispersion of molecules with polar-functional groups as well as the molecular ordering of mixed SAMs is attributed to such adsorption behaviors of V₂O₅ nanowires.     

Non-contact AFM images of a C60 molecule adsorbed on the Si(0 0 1) surface: An ab initio method

A theoretical non-contact atomic force microscope (nc-AFM) image is simulated for an individual C₆₀ molecule adsorbed on the clean Si(0 0 1) surface. The ability to identify the intramolecular features of the molecule though nc-AFM imaging would allow many of the different configurations the molecule may take when adsorbed, to be identified. This would be an important preliminary step in the manipulation of the molecule along the surface, as the initial configuration that the molecule is in will affect the periodicity of the tip trajectory during the manipulation event (see D.L. Keeling et al., Phys. Rev. Lett. 94 (2005) #146104). Presented in this paper are simulated images and force curves above important sites for key stable configurations of the C₆₀ molecule. It is shown that in principle it is possible to distinguish between the different configurations of the molecule using nc-AFM. An ab initio DFT method was used to accurately describe the chemical interaction between the adsorbate and the Si tip, which has a single dangling bond at its apex.     

Combined spectroscopy and microscopy of supported MoS2 nanoparticles

Supported molybdenum-sulfide nanoparticles are known catalysts for petroleum hydrodesulfurization as well as for electrochemical hydrogen evolution. In this study, we investigate molybdenum-sulfide nanoparticles supported on Au(1 1 1) using X-ray photoelectron spectroscopy (XPS) and scanning tunneling microscopy (STM), aiming to correlate spectroscopically determined chemical states with atomically resolved nanostructure. The results of this study allow us to conclude the following: (1) the XPS results from our model system are in good agreement with previously published results on supported MoS₂ for industrial applications, validating in part the fidelity of the model system; (2) STM reveals that catalytically active, crystalline MoS₂ nanoparticles exhibiting the well-known metallic edge state are only present after a post-deposition annealing step in the synthesis procedure, without which the particles exhibit amorphous shapes and incomplete sulfidation; and (3) the sulfided nanoparticles are found to be stable in air at room temperature.