Structure and mechanical properties of ceramic coatings fabricated by plasma electrolytic oxidation on aluminized steel

Ceramic coatings were formed by plasma electrolytic oxidation (PEO) on aluminized steel. Characteristics of the average anodic voltages versus treatment time were observed during the PEO process. The micrographs, compositions and mechanical properties of ceramic coatings were investigated. The results show that the anodic voltage profile for processing of aluminized steel is similar to that for processing bulk Al alloy during early PEO stages and that the thickness of ceramic coating increases approximately linearly with the Al layer consumption. Once the Al layer is completely transformed, the FeAl intermetallic layer begins to participate in the PEO process. At this point, the anodic voltage of aluminized steel descends, and the thickness of ceramic coating grows more slowly. At the same time, some micro-cracks are observed at the Al₂O₃/FeAl interface. The final ceramic coating mainly consists of γ-Al₂O₃, mullite, and α-Al₂O₃ phases. PEO ceramic coatings have excellent elastic recovery and high load supporting performance. Nanohardness of ceramic coating reaches about 19.6 GPa.     

Microstructure and corrosion resistance behavior of ceramic coatings on biomedical NiTi alloy prepared by micro-arc oxidation

In this paper, ceramic coatings were prepared on biomedical NiTi alloys by micro-arc oxidation (MAO) in constant voltage mode. The current density-time response was recorded during the MAO process. The microstructure, element distribution and phase composition of the coatings prepared at different MAO treatment times were investigated by scanning electron microscopy (SEM), energy dispersive X-ray spectrometer (EDS), thin-film X-ray diffraction (TF-XRD) and X-ray photoelectron spectroscopy (XPS). The corrosion behavior of the coatings in 0.9% NaCl solution was evaluated by the potentiodynamic polarization test. It is found that the coatings become more compact with increasing the MAO treatment time, and the growth rate of coating decreases. The results of TF-XRD, EDS and XPS indicate that the coatings are composed of a large amount of γ-Al₂O₃ and a little α-Al₂O₃, TiO₂ and Ni₂O₃. The Ni content of the coatings is about 3 at.%, which is greatly lower than that of NiTi substrate. The bonding strength of coating-substrate is higher than 40 MPa for all the samples in this study. The corrosion resistance of the coatings is about two orders of magnitude higher than that of the uncoated NiTi alloy.     

电流密度对铝合金微弧氧化膜物理化学特性的影响

利用微弧氧化(MAO)技术，在LYl2铝合金上沉积了显微硬度达42.14GPa的超硬陶瓷膜.采用x射线衍射仪和显微硬度计研究了阳极电流密度j_a和阴极、阳极电流密度比j_c/j_a对MAO膜相构成和力学特性的影响.此外，利用扫描电子显微镜和恒电位仪分别对膜的微结构和抗点腐蚀特性进行了分析.结果表明，高j_a制备的膜主要含α-Al₂O₃相，低j_a制备的膜主要含γ-Al₂O₃相.显微硬度测试表明，这类膜有较高的硬度，但以j_a=15A/dm²和j_c/j_a=0.7制备的陶瓷膜硬度最高.抗点腐蚀测试表明，j_c/j_a对陶瓷膜的微结构有很强的影响. 关键词： 微弧氧化 显微硬度 电流密度 抗点腐蚀     

Deposition of duplex Al2O3/aluminum coatings on steel using a combined technique of arc spraying and plasma electrolytic oxidation

Plasma electrolytic oxidation (PEO) is a cost-effective technique that can be used to prepare ceramic coatings on metals such as Ti, Al, Mg, Nb, etc., and their alloys, but this promising technique cannot be used to modify the surface properties of steels, which are the most widely used materials in engineering. In order to prepare metallurgically bonded ceramic coatings on steels, a combined technique of arc spraying and plasma electrolytic oxidation (PEO) was adopted. In this work, metallurgically bonded ceramic coatings on steels were obtained using this method. We firstly prepared aluminum coatings on steels by arc spraying, and then obtained the metallurgically bonded ceramic coatings on aluminum coatings by PEO. The characteristics of duplex coatings were analyzed by X-ray diffractometer (XRD) and scanning electron microscopy (SEM). The corrosion and wear resistance of the ceramic coatings were also studied. The results show that, duplex Al₂O₃/aluminum coatings have been deposited on steel substrate after the combined treatment. The ceramic coatings are mainly composed of α-Al₂O₃, γ-Al₂O₃, θ-Al₂O₃ and some amorphous phase. The duplex coatings show favorable corrosion and wear resistance properties. The investigations indicate that the combination of arc spraying and plasma electrolytic oxidation proves a promising technique for surface modification of steels for protective purposes.     

Effects of duty ratio at low frequency on growth mechanism of micro-plasma oxidation ceramic coatings on Ti alloy

The aim of this work is to study the effects of duty ratio on the growth mechanism of the ceramic coatings on Ti-6Al-4V alloy prepared by pulsed single-polar MPO at 50 Hz in NaAlO₂ solution. The phase composition of the coatings was studied by X-ray diffraction, and the morphology and the element distribution in the coating were examined through scanning electron microscopy and energy dispersive spectroscopy. The thickness of the coatings was measured by eddy current coating thickness gauge. The corrosion resistance of the coated samples was examined by linear sweep voltammetry technique in 3.5% NaCl solution. The changes of the duty ratio (D) of the anode process led to the changes of the mode of the spark discharge during the pulsed single-polar MPO process, which further influenced the structure and the morphology of the ceramic coatings. The coatings prepared at D = 10% were composed of a large amount of Al₂TiO₅ and a little γ-Al₂O₃ while the coatings prepared at D = 45% were mainly composed of α-Al₂O₃ and γ-Al₂O₃. The coating thickness and the roughness were both increased with the increasing D due to the formation of Al₂O₃. The formation of Al₂TiO₅ resulted from the spark discharge due to the breakdown of the oxide film, while the formation of Al₂O₃ resulted from the spark discharge due to the breakdown of the vapor envelope. The ceramic coatings improved the corrosion resistance of Ti-6Al-4V alloy. And the surface morphology and the coating thickness determined the corrosion resistance of the coated samples prepared at D = 45% was better than that of the coated samples prepared at D = 10%.     

Ultra-hard ceramic coatings fabricated through microarc oxidation on aluminium alloy

Ultra-hard ceramic coatings with microhardness of 2535 Hv have been synthesized on the Al alloy substrate by microarc oxidation (MAO) technique. The effects of anodic current density (j_a) and the ratio of cathodic to anodic current density (j_c/j_a) on the mechanical and corrosion resistance properties of MAO coatings have been studied by microhardness and pitting corrosion tests, respectively. In addition, the phase composition and microstructure of the coatings were analyzed by X-ray diffraction (XRD) and scanning electron microscopy (SEM), respectively. The results show that the coatings prepared at high anodic current density consist mainly of α-Al₂O₃, while those fabricated at low anodic current density are almost composed of γ-Al₂O₃. Microhardness test shows that the coatings have high microhardness, and the highest one is found in the coating formed at j_a = 15 A/dm² and j_c/j_a = 0.7. Pitting corrosion test shows that the structure of coatings is strongly influenced by the varying j_c/j_a.     

Influence of treating frequency on microstructure and properties of Al2O3 coating on 304 stainless steel by cathodic plasma electrolytic deposition

Alumina ceramic coatings were fabricated on 304 stainless steel by cathodic plasma electrolytic deposition (CPED). Influence of treating frequency of the power supply on the microstructure and properties of the coatings were studied. The results indicated that coatings obtained at various frequencies on 304 stainless steels were all composed of α-Al₂O₃ and γ-Al₂O₃, and α-Al₂O₃ was the dominant phase. The contents of α-Al₂O₃ decreased gradually in a very small rate with increasing the frequency and γ-Al₂O₃ gradually increased. The surface of alumina ceramic coating was porous. With increasing the frequency, the coating surface gradually became less rough and more compact, resulting in low surface roughness. The bonding strength of Al₂O₃ coating was higher than 22 MPa and was not strongly affected by treating frequency. With increasing the frequency, the alumina coated steels showed better and gradually increasing corrosion resistance than the uncoated one in 3.5% NaCl solution. The coating steel with desirable corrosion resistance was obtained at 800 Hz whose corrosion current potential and corrosion density were −0.237 V and 7.367 × 10⁻⁸ A/cm², respectively.     

Formation of Al2O3 coatings on NiTi alloy by micro-arc oxidation method

Rough and porous Al₂O₃ coatings containing Ca and P were prepared on Ti–50.8 at.% Ni alloy by micro-arc oxidation (MAO) technique. The microstructure, elemental and phase composition of the coatings were investigated by scanning electron microscopy (SEM), energy dispersive X-ray spectrometer (EDS) and thin-film X-ray diffraction (TF-XRD). The thickness of the coatings was measured by eddy current coating thickness gauge. The corrosion resistance and the nickel release of the coated and uncoated samples were examined by potentiodynamic polarization tests and immersion tests in Hank’s solution, respectively. The results show that the coatings are mainly composed of γ-Al₂O₃ crystal phase. The Ni content of the coatings is about 3.5 at.%, which is greatly lower than that of NiTi substrate. With increasing treatment time, both thickness and roughness of the coatings increase. The corrosion resistance of the coated samples is about two orders of magnitude higher than that of the uncoated NiTi alloy. The concentration of Ni released from coated NiTi samples is much lower than that of uncoated NiTi sample. It can be reduced in the factor of one-seventh compared with the uncoated NiTi sample after 3 weeks immersion in Hank’s solution.     

Laser surface remelting of plasma sprayed nanostructured Al2O3-13wt%TiO2 coatings on titanium alloy

Plasma sprayed nanostructured coatings were successfully fabricated on a titanium alloy (Ti-6Al-4V) substrate using the as-prepared nanostructured Al₂O₃-13wt%TiO₂ feedstock. A CO₂ laser was used to remelt the plasma sprayed coatings. The effects of laser remelting on the phase constituents, microstructure and properties of the ceramic coatings were investigated. The laser remelted coatings (LRmC) possessed a much denser and more homogenous structure and excellent metallurgical bonding to the substrate. The average porosity of the LRmC was reduced to 0.9%, compared with 6.2% of the as-sprayed coatings. The net-like structure in the as-prepared feedstock remained in the coatings before and after laser remelting. The metastable γ-Al₂O₃ phase in the as-sprayed coatings transformed to stable α-Al₂O₃ during laser remelting. The LRmC could remain nanostructure. The microhardness of the coatings was enhanced to 1000-1400 HV_0.3 after laser remelting, which was much higher than that of the plasma sprayed coatings and 2-3 times higher that of the substrate. Significant decreases in surface roughness were also found in the LRmC.     

Improvement of surface porosity and properties of alumina films by incorporation of Fe micrograins in micro-arc oxidation

Micro-arc oxidation (MAO) is an effective approach to improve the properties of aluminum and its alloy by forming ceramic films on the surface. However, the oxide layers often have a porous surface structure, which exhibits relatively high friction coefficients. In this work, in order to enhance the surface and mechanical properties of the films produced by micro-arc oxidation, Al₂O₃ coatings embedded with Fe micrograins of different thicknesses were produced on aluminum alloys by adding Fe micrograins into the electrolyte during MAO. Compared to the Al₂O₃ coatings without Fe micrograins, the MAO Al₂O₃ coatings with Fe micrograins are much denser and harder, and the wear resistance is also improved significantly. The enhancement can be attributed to the enhancement of the surface structure and morphology of the MAO Al₂O₃ coatings with embedded Fe micrograins.     

Influence of C3H8O3 in the electrolyte on characteristics and corrosion resistance of the microarc oxidation coatings formed on AZ91D magnesium alloy surface

Ceramic coatings were fabricated on AZ91D Mg-alloy substrate by microarc oxidation in Na₂SiO₃-NaOH-Na₂EDTA electrolytes with and without C₃H₈O₃ addition. The effects of different concentrations of C₃H₈O₃ contained in the electrolyte on coatings thickness were investigated. The surface morphologies, RMS roughness, phase compositions and corrosion resistance property of the ceramic coatings were analyzed by scanning electron microscopy (SEM), atomic force microscopy (AFM), X-ray diffraction (XRD), and electrochemical corrosion test respectively. It is found that the addition of C₃H₈O₃ into silicate electrolyte leads to increase of the unit-area adsorptive capacity of the negative ions at anode-electrolyte interface and thus improves the compactness and corrosion resistance of the MAO coating. The coating thickness decreases gradually with the increase of concentrations of C₃H₈O₃ in the electrolyte. The oxide coating formed in base electrolyte containing 4 mL/L C₃H₈O₃ exhibits the best surface appearance, the lowest surface RMS roughness (174 nm) and highest corrosion resistance. In addition, both ceramic coatings treated in base electrolyte with and without C₃H₈O₃ are mainly composed of periclase MgO and forsterite Mg₂SiO₄ phase, but no diffraction peak of Mg phase is found in the patterns.     

Investigation of Ceramic-Like Coatings Formed on Aluminum Composites by Microarc Oxidation

Ceramic-like coatings with a thickness of up to 40 μm are formed on aluminum composites without additives and with copper additives (1 and 4.5%) in a silicate-alkaline electrolyte by microarc oxidation. The composites are prepared by powder metallurgy (cold pressing and sintering in forevacuum). An increase in the copper concentration in the composites to 4.5% leads to the retardation of anode voltage growth on the initial stage of oxidation corresponding to the formation of a barrier layer. The coatings are studied by scanning electron microscopy, X-ray microanalysis, X-ray photoelectron spectroscopy, and X-ray diffraction. The morphology of their surface corresponds to the morphology of the surface of coatings on compact aluminum alloys. According to X-ray photoelectron spectroscopy, a thin 1-μm layer forms on the surface. It consists predominantly of electrolyte components. X-ray diffraction analysis shows that the coatings mainly consist of γ-Al₂O₃ oxide as well as the η-Al₂O₃ phase, the peaks of which are broadened. This broadening is characteristic of the amorphous component and may be due to the presence of nanocrystalline regions in the coating structure. In the coatings on the composite Al + 4.5% Cu, mullite Al₂SiO₅ and copper oxide CuO are also found. The excess aluminum content may be associated with residual unoxidized aluminum inclusions in the structure of the coatings.     

电解等离子体法制备Al2O3陶瓷层及其特性研究

利用电弧喷铝并重熔后进行电解等离子体处理(EPP)的方法在Q235钢基体上制备出呈冶金结 合的Al₂O₃陶瓷层.利用XRD，SEM和EDS等手段对陶瓷层的成分和显 微组织进行了分析， 测定了陶瓷层的耐蚀性能和耐磨性能.实验结果表明，陶瓷层主要由α-Al₂O3，γ-Al₂O₃，θ-Al₂O₃以及一 些非晶相组成，组织致密，耐蚀性能和耐磨性能良好. 关键词： 电解等离子体处理 陶瓷层 复合技术 生长机理     

Growth characteristics of micro-plasma oxidation ceramic coatings on Ti alloy by inductively coupled plasma-atomic emission spectrometer technique

The aim of this work was to study the growth characteristics of micro-plasma oxidation ceramic coatings on Ti-6Al-4V alloy. Compound ceramic coatings were prepared on Ti-6Al-4V alloy by pulsed micro-plasma oxidation (MPO) in NaAlO₂ solution. The phase composition and surface morphology of the coating were investigated by X-ray diffractometry and scanning electron microscopy. The solution of Ti from the substrate and the content of Al in the electrolyte were studied by inductively coupled plasma-atomic emission spectrometer (ICP-AES) technique. Ti from the substrate dissolved and came into the coating and the electrolyte during MPO process. The content of Ti in the electrolyte under the pulsed bi-polar mode was more than that of the pulsed single-polar mode. The phase composition and structure of the coating was attributable to the space steric hindrance of Al congregated on the electrode surface due to the effect of the electric field and the electrolyte characters. For the pulsed single-polar mode, the coating was mainly composed of a large amount of α-Al₂O₃ and a small amount of γ-Al₂O₃. And the coating was mainly structured by Al from the electrolyte. However, the coating was composed of a large amount of Al₂TiO₅ and a little α-Al₂O₃ and rutile TiO₂ for the pulsed bi-polar mode. And the coating was structured both by Ti from the substrate and Al from the electrolyte.     

Fabrication and luminous properties of phosphor ceramic for application in automotive laser headlight

We report on the optimization of fabrication of a ceramic phosphor plate (CPP) using α-Al₂O₃ as functional materials for an automotive laser headlamp. The prepared CPP shows the high luminous characteristics with increasing α-Al₂O₃ contents because of the light scattering of the hexagonal structure of α-Al₂O₃ materials. We investigated the correlation between α-Al₂O₃ and thickness of CPP. The luminous properties of the CPP are improved and optimized according to the variables of one. We found that the prepared sample is a potential material for future solid-state laser lighting in application as an automotive headlamp.     

Formation and structure of sphene/titania composite coatings on titanium formed by a hybrid technique of microarc oxidation and heat-treatment

Sphene/titania composite coatings were fabricated on titanium by a hybrid technique of microarc oxidation (MAO) and heat treatment. The high-applied voltages promote the formation of sphene in the MAO coatings after heat-treatment. Heat treatment could change the surface morphology of the MAO coatings such as roughness, macropores size and density and the thickness of the MAO coatings. Increasing the heat-treatment temperature decreased the atomic concentration ratios of Ti/Si and Ti/Ca of the MAO coatings. The chemical states of Ti⁴⁺, Ca²⁺, Si²⁺ and O²⁻ were observed on all the coatings. Additionally, Ti²⁺ was detected in the MAO and heat-treated MAO coatings at 600 and 700 °C. The heat-treatment has obvious effect on the chemical states of Si, Ti and O elements due to the formation of sphene and oxidation of TiO phase of the MAO coating, but did not affect that of Ca. In the heat-treated MAO coatings at 800 °C (MAO-H8), the titanium surface shows a MAO top layer and oxidized interior layer. A concentration gradient in components in the MAO layer of the MAO-H8 coating was formed.     

Microstructure characteristic of ceramic coatings fabricated on magnesium alloys by micro-arc oxidation in alkaline silicate solutions

Micro-arc oxidation (MAO) of AZ31B magnesium alloys was studied in alkaline silicate solutions at constant applied current densities. The microstructure, phase composition and elemental distribution of ceramic coatings were investigated using scanning electron microscopy (SEM), X-ray diffraction (XRD) and energy-dispersive spectroscopy (EDX). There are two inflections in the voltage-time response, three regions were identifiable and each of the regions was almost linear. The pores with different shapes distributed all over the coating surface, the number of the pores was decreasing, while the diameter was apparently increasing with prolonged MAO treatment time. There were also cracks on the coating surface, resulting from the rapid solidification of the molten oxide. The ceramic coating was comprised of two layers, an outer loose layer and an inner dense layer. The ceramic coating was mainly composed of forsterite phase Mg₂SiO₄ and MgO; the formation of MgO was similar to conversional anodizing technology, while formation of Mg₂SiO₄ was attributed to a high temperature phase transformation reaction. Presence of Si and O indicated that the electrolyte components had intensively incorporated into coatings.     

Effect of α-Al2O3 on the properties of cold sprayed Al/α-Al2O3 composite coatings on AZ91D magnesium alloy

Composite coatings using pure Al powder blended with α-Al₂O₃ as feedstock were deposited on AZ91D magnesium alloy substrates by cold spray (CS). The content of α-Al₂O₃ in the feedstock was 25 wt.% and 50 wt.%, respectively. The effects of α-Al₂O₃ on the porosity, microhardness, adhesion and tensile strength of the coatings were studied. Electrochemical tests were carried out in neutral 3.5 wt.% NaCl solution to evaluate the effect of α-Al₂O₃ on the corrosion behavior of the coatings. The results showed that the composite coatings possessed lower porosity, higher adhesion strength and tensile strength than cold sprayed pure Al coating. The corrosion current densities of the composite coatings were similar to that of the pure Al coating and much higher than that of bare AZ91D magnesium alloy.     

Effect of additives on structure and corrosion resistance of ceramic coatings on Mg–Li alloy by micro-arc oxidation

In order to improve the corrosion resistance of ceramic coatings formed on Mg–5mass%Li substrate by micro-arc oxidation (MAO) method, two kinds of additives (Na₂B₄O₇ and EDTA) were doped in Na₂SiO₃–Na₃PO₄ solution system. The surface and cross-section morphology feature, phase composition and elemental composition were examined by SEM, XRD and EDX, respectively. Corrosion resistance of ceramic coating was tested by electrochemical methods. It was revealed that all coatings were composed of MgO and Mg₂SiO₄, and had porous surface structure. Doping of additives had little effect on the elemental composition, while it influenced the morphological feature of the coating. The results of electrochemical tests showed that the coatings prepared in the solutions with additive had good corrosion resistance. The addition of EDTA to the solution made coatings thinner and more uniform which resulted in better general corrosion resistance. The addition of Na₂B₄O₇ to the solution made coatings much thicker and compacter, which improved the pitting corrosion resistance.     

Effect of NaAlO2 concentrations on microstructure and corrosion resistance of Al2O3/ZrO2 coatings formed on zirconium by micro-arc oxidation

In this study, Al₂O₃/ZrO₂ composite coatings were prepared on Zr substrates by micro-arc oxidation (MAO) in the NaAlO₂-containing electrolytes, and the effect of NaAlO₂ concentration on the microstructure, bond strength, microhardness and corrosion resistance of coatings was systematically investigated. The study reveals that the adequate NaAlO₂ in the electrolyte (>0.2 M) is essential to the formation of needle-like α-Al₂O₃ in the coatings, and the amount of α-Al₂O₃ rises with the increase of the NaAlO₂ concentration. m-ZrO₂ and t-ZrO₂ are present in all of the coatings, but their relative amount largely depends on the amount of Al₂O₃. It is also found that as the NaAlO₂ concentration increases from 0.2 to 0.3 M, the coating becomes denser and thicker, and its bond strength, maximum microhardness and corrosion resistance increases as well. The coating formed at 0.3 M NaAlO₂ demonstrates the highest bond strength of 52 MPa, the maximum microhardness of 1600 Hv_0.2N and the superior corrosion resistance. However, the overhigh concentration of NaAlO₂ (0.35 M) is found harmful to the coating's microstructure and properties.