Influence of assisted ion energy on surface roughness and mechanical properties of boron carbon nitride films synthesized by DIBSD

The BCN thin films were produced by dual ion beam sputtering deposition (DIBSD). The influence of assisted ion energy on surface roughness and mechanical properties of BCN films were investigated. The surface roughness was determined by atomic force microscopy (AFM) and the mechanical properties of BCN firms were evaluated by nano-indentation in N₂ gas. The composition, structure and chemical bonding of the BCN thin films were analyzed by using energy dispersive spectroscopy (EDS), transmission electron microscopy (TEM), laser Raman spectroscopy and Fourier transform infrared spectroscopy (FTIR). These films appeared as amorphous structure. As a result, the BCN films with the smoothest surface (R_a = 0.35 nm and R_p-v = 4.4 nm) and the highest nano-hardness of 30.1 GPa and elastic modulus of 232.6 GPa were obtained at 200 eV and 12 mA with N₂:Ar = 1:1, and the chemical composition of this BCN film was 81 at.% B, 14 at.% C and 5 at.% N. Moreover, several bonding states such as B-N, B-C and C-N were observed in BCN thin films.     

Diamond-like phase formation in an amorphous carbon films prepared by periodic pulsed laser deposition and laser irradiation method

Diamond-like carbon (DLC) films were fabricated by pulsed laser ablation of a liquid target. During deposition process the growing films were exited by a laser beam irradiation. The films were deposited onto the fused silica using 248 nm KrF eximer laser at room temperature and 10⁻³ mbar pressure. Film irradiation was carried out by the same KrF laser operating periodically between the deposition and excitation regimes. Deposited DLC films were characterized by Raman scattering spectroscopy. The results obtained suggested that laser irradiation intensity has noticeable influence on the structure and hybridization of carbon atoms deposited. For materials deposited at moderate irradiation intensities a very high and sharp peak appeared at 1332 cm⁻¹, characteristic of diamond crystals. At higher irradiation intensities the graphitization of the amorphous films was observed. Thus, at optimal energy density the individual sp³-hybridized carbon phase was deposited inside the amorphous carbon structure. Surface morphology for DLC has been analyzed using atomic force microscopy (AFM) indicating that more regular diamond cluster formation at optimal additional laser illumination conditions (∼20 mJ per impulse) is possible.     

Study of porous carbon thin films produced by pulsed laser deposition

Amorphous carbon is an interesting material and its properties can be varied by tuning its diamond-like (sp³) fractions. The diamond-like fractions in an amorphous carbon films depends on the kinetic energy of the deposited carbon ions. Porous amorphous carbon thin films were deposited onto silicon substrates at room temperature in a vacuum chamber by Glancing Angle Pulsed Laser Deposition (GAPLD). Krypton fluoride (248 nm) laser pulses with duration of 15 ns and intensities of 1-20 GW/cm² were used. In GAPLD, the angles between the substrate normal and the trajectory of the incident deposition flux are set to be almost 90°. Porous thin films consisting of carbon nanowires with diameters less than 100 nm were formed due to a self-shadowing effect. The kinetic energies of the deposited ions, the deposition rate of the films and the size of the nanowires were investigated. The sp³ fraction of the porous carbon films produced at intensity around 20 GW/cm² were estimated from their Raman spectra.     

Femtosecond pulsed laser deposition of diamond-like carbon films: The effect of double laser pulses

The bonding structure of carbon films prepared by pulsed laser deposition is determined by the plasma properties especially the change of the kinetic energy. Using double laser pulses the ablation process and the characteristics of the generated plasma can be controlled by the setting of the delay between the pulses. In our experiments, amorphous carbon films have been deposited in vacuum onto Si substrates by double pulses from a Ti:sapphire laser (180 fs, λ = 800 nm, at 1 kHz) and a KrF laser system (500 fs, λ = 248 nm, at 5 Hz). The intensities have been varied in the range of 3.4 × 10¹² to 2 × 10¹³ W/cm². The morphology and the main properties of the thin layers were investigated as a function of the time delay between the two ablating pulses (0-116.8 ps) and as a function of the irradiated area on the target surface. Atomic force microscopy, spectroscopic ellipsometry and Raman-spectroscopy were used to characterize the films. It was demonstrated that the change of the delay and the spot size results in the modification of the thickness distribution of the layers, and the carbon sp²/sp³ bonding ratio.     

The effect of different gas atmospheres on luminescent properties of pulsed laser ablated SrAl2O4:Eu,Dy thinfilms

SrAl₂O₄:Eu²⁺,Dy³⁺ thin films were grown on Si (1 0 0) substrates using the pulsed laser deposition (PLD) technique to investigate the effect of vacuum, oxygen (O₂) and argon (Ar) deposition atmospheres on the structural, morphological, photoluminescence (PL) and cathodoluminescence (CL) properties of the films. The films were ablated using a 248 nm KrF excimer laser. Atomic force microscopy (AFM), scanning electron microscopy (SEM), X-ray diffraction (XRD), energy dispersive X-ray spectroscopy (EDS) and fluorescence spectrophotometry were used to characterize the thin films. Auger electron spectroscopy (AES) combined with CL spectroscopy were employed for the surface characterization and electron-beam induced degradation of the films. Better PL intensities were obtained from the unannealed films prepared in Ar and O₂ atmospheres with respect to those prepared in vacuum. A stable green emission peak at 515 nm, attributed to 4f⁶5d¹→4f⁷ Eu²⁺ transitions were obtained with less intense peaks at 619 nm, which were attributed to transitions in Eu³⁺. After annealing the films prepared in vacuum at 800 °C for 2 h, the intensity of the green emission (520 nm) of the thin film increased considerably. The amorphous thin film was crystalline after the annealing process. The CL intensity increased under prolonged electron bombardment during the removal of C due to electron stimulated surface chemical reactions (ESSCRs) on the surface of the SrAl₂O₄:Eu²⁺, Dy³⁺ thin films. The CL stabilized and stayed constant thereafter.     

Characterization of polymer thin films obtained by pulsed laser deposition

The development of laser techniques for the deposition of polymer and biomaterial thin films on solid surfaces in a controlled manner has attracted great attention during the last few years. Here we report the deposition of thin polymer films, namely Polyepichlorhydrin by pulsed laser deposition. Polyepichlorhydrin polymer was deposited on flat substrate (i.e. silicon) using an NdYAG laser (266 nm, 5 ns pulse duration and 10 Hz repetition rate).The obtained thin films have been characterized by atomic force microscopy, scanning electron microscopy, Fourier transform infrared spectroscopy and spectroscopic ellipsometry.It was found that for laser fluences up to 1.5 J/cm² the chemical structure of the deposited polyepichlorhydrin polymer thin layers resembles to the native polymer, whilst by increasing the laser fluence above 1.5 J/cm² the polyepichlorohydrin films present deviations from the bulk polymer.Morphological investigations (atomic force microscopy and scanning electron microscopy) reveal continuous polyepichlorhydrin thin films for a relatively narrow range of fluences (1-1.5 J/cm²).The wavelength dependence of the refractive index and extinction coefficient was determined by ellipsometry studies which lead to new insights about the material.The obtained results indicate that pulsed laser deposition method is potentially useful for the fabrication of polymer thin films to be used in applications including electronics, microsensor or bioengineering industries.     

Stimulation of the local growth of aligned carbon nanotubes by pulse laser exposure of the substrate

The local stimulation of carbon nanotubes (CNT) growth at the laser-modified sites that have been obtained by excimer laser irradiation at 248 nm causing a local surface modification has been investigated by two different processing methods. The influence of the laser processing parameters on the CNT growth is compared for the irradiation of thin spin-coated iron nitrate films on silicon substrates and the backside irradiation of a fused silica substrate being in contact with an iron nitrate solution. Both techniques cause the formation of catalytic surface sites either by decomposition of the film or by deposition from the solution. For both laser modification approaches the local growth of vertical aligned nanotubes has been observed. In the case of spin-coated film the laser irradiation conditions have only a small influence on the CNT growth whereas at backside modification by means of a solution a strong dependence on the laser processing parameters has been found.     

Laser deposition of cryoglobulin blood proteins thin films by matrix assisted pulsed laser evaporation

We report the first successful deposition of type II cryoglobulin blood protein thin films by matrix assisted pulsed laser evaporation (MAPLE) using a KrF^* excimer laser source (λ = 248 nm, τ_FWHM ≈ 20 ns) operated at a repetition rate of 10 Hz. We demonstrate by AFM and FTIR that MAPLE-deposited thin films consist of starting type II cryoglobulin only, maintaining its chemical structure and biological functionality, being properly collected and processed. The dependence on incident laser fluence of the induced surface morphology is presented. The presence of type II cryoglobulin was revealed as aggregates of globular material in the MAPLE-deposited thin films and confirmed by standard cryoglobulin tests.     

Laser microstructuring and annealing processes for lithium manganese oxide cathodes

It is expected that cathodes for lithium-ion batteries (LIB) composed out of nano-composite materials lead to an increase in power density of the LIB due to large electrochemically active surface areas but cathodes made of lithium manganese oxides (Li-Mn-O) suffer from structural instabilities due to their sensitivity to the average manganese oxidation state. Therefore, thin films in the Li-Mn-O system were synthesized by non-reactive radiofrequency magnetron sputtering of a spinel lithium manganese oxide target. For the enhancement of the power density and cycle stability, large area direct laser patterning using UV-laser radiation with a wavelength of 248 nm was performed. Subsequent laser annealing processes were investigated in a second step in order to set up a spinel-like phase using 940 nm laser radiation at a temperature of 680 °C. The interaction processes between UV-laser radiation and the material was investigated using laser ablation inductively coupled plasma mass spectroscopy. The changes in phase, structure and grain shape of the thin films due to the annealing process were recorded using Raman spectroscopy, X-ray diffraction and scanning electron microscopy. The structured cathodes were cycled using standard electrolyte and a metallic lithium anode. Different surface structures were investigated and a significant increase in cycling stability was found. Surface chemistry of an as-deposited as well as an electrochemically cycled thin film was investigated via X-ray photoelectron spectroscopy.     

The structure of thin carbon films deposited at 13.5 nm EUV irradiation

In this work, the structure and chemistry of thin nm-thick carbon films deposited on a substrate using strong 13.5 nm EUV irradiation under a strong vacuum were studied. The film structure was studied by Raman spectroscopy in comparison with the Raman spectra of well-known carbon phases: diamond, single-wall nanotubes, nano- and micro-crystalline graphite and amorphous carbon. As well, FTIR spectroscopy was used to study possible IR-active chemical bonds, primarily, hydrogen bonds. It was shown that films deposited on a surface under EUV irradiation consists of amorphous sp ²-carbon. The mechanisms of deposition are discussed briefly. Knowledge about the structure and chemistry of such carbon films is very important for EUV lithography.     

Study of temperature dependence and angular distribution of poly(9,9-dioctylfluorene) polymer films deposited by matrix-assisted pulsed laser evaporation (MAPLE)

Poly(9,9-dioctylfluorene) (PFO) polymer films were deposited by matrix-assisted pulsed laser evaporation (MAPLE) technique. The polymer was diluted (0.5 wt%) in tetrahydrofuran and, once cooled to liquid nitrogen temperature, it was irradiated with a KrF excimer laser. 10,000 laser pulses were used to deposit PFO films on 〈1 0 0〉 Si substrates at different temperatures (−16, 30, 50 and 70 °C). One PFO film was deposited with 16,000 laser pulses at a substrate temperature of 50 °C. The morphology, optical and structural properties of the films were investigated by SEM, AFM, PL and FTIR spectroscopy. SEM inspection showed different characteristic features on the film surface, like deflated balloons, droplets and entangled polymer filaments. The roughness of the films was, at least partially, controlled by substrate heating, which however had the effect to reduce the deposition rate. The increase of the laser pulse number modified the target composition and increased the surface roughness. The angular distribution of the material ejected from the target confirmed the forward ejection of the target material. PFO films presented negligible modification of the chemical structure respect to the bulk material.     

Thin films of polyaniline deposited by MAPLE technique

Polyaniline (PAni) has important electro-conductive properties, high absorbance in microwave range and it is also frequently used in gas sensors because of its capability to convert chemical interactions into electrical signals. The methods of obtaining polyaniline in the form of thin films and/or nanostructures are complicated and request special physical and chemical treatments, both on the substrate surface and for the polymer itself.In this paper we applied matrix assisted pulsed lased evaporation (MAPLE) for obtaining thin films and nanostructures of polyaniline. In MAPLE, the target consisting of the material (usually 0.2-3 wt%) dissolved in a solvent is frozen and it is evaporated using a laser. In our case polyaniline-emeraldine salt (PAni-ES) was dissolved in xylene or toluene, frozen in liquid nitrogen and was used as target. The third and the fourth harmonics of a Nd-YAG laser (λ = 355 nm and 266 nm) were used as laser sources. The obtained films have been characterized by atomic force microscopy, dielectric spectroscopy and Fourier transform infrared spectroscopy. The influence of the solvent type and of the laser parameters (wavelengths and fluence) on the polyaniline structures composition and properties has been investigated.     

Electron beam evaporated LaF3 thin films prepared by different temperatures and deposition rates

LaF₃ thin films were prepared by electron beam evaporation with different temperatures and deposition rates. Microstructure properties including crystalline structure and surface roughness were investigated by X-ray diffraction (XRD) and optical profilograph. X-ray photoelectron spectroscopy (XPS) was employed to study the chemical composition of the films. Optical properties (transmittance and refractive index) and laser induce damage threshold (LIDT) at 355 nm of the films were also characterized. The effects of deposition rate and substrate temperature on microstructure, optical properties and LIDT of LaF₃ thin films were discussed, respectively.     

Thin films of silver nanoparticles deposited in vacuum by pulsed laser ablation using a YAG:Nd laser

We report the deposition of thin films of silver (Ag) nanoparticles by pulsed laser ablation in vacuum using the third line (355 nm) of a YAG:Nd laser. The nanostructure and/or morphology of the films was investigated as a function of the number of ablation pulses, by means of transmission electron microscopy and atomic force microscopy. Our results show that films deposited with a small number of ablation pulses (500 or less), are not continuous, but formed of isolated nearly spherical Ag nanoparticles with diameters in the range from 1 nm to 8 nm. The effect of increasing the number of pulses by one order of magnitude (5000) is to increase the mean diameter of the globular nanoparticles and also the Ag areal density. Further increase of the number of pulses, up to 10,000, produces the formation of larger and anisotropic nanoparticles, and for 15,000 pulses, quasi-percolated Ag films are obtained. The presence of Ag nanoparticles in the films was also evidenced from the appearance of a strong optical absorption band associated with surface plasmon resonance. This band was widened and its peak shifted from 425 nm to 700 nm as the number of laser pulses was increased from 500 to 15,000.     

AlN:Cr thin films synthesized by pulsed laser deposition: Studies by X-ray diffraction and spectroscopic ellipsometry

The structure and optical properties of AlN thin films doped with Cr atoms were studied by X-ray diffractometry, Fourier transform infrared spectroscopy and spectroscopic ellipsometry analyses. The films were synthesized by pulsed laser deposition from an AlN:Cr (10% Cr) target onto Si(1 0 0) wafers in vacuum at residual pressure of 10⁻³ Pa or in nitrogen at a dynamic pressure of 0.1 Pa. The study of the XRD patterns revealed that both phases co-existed in the synthesized films and that the amorphous one was prevalent. Two different amorphous matrices, i.e. two types of chemical bond arrangements, were found in films deposited at 0.1 Pa N₂. By difference, deposition in vacuum resulted in the coexistence of hexagonal and cubic crystallites embedded into an amorphous matrix. The introduction of Cr atoms into the AlN lattice causes a broadening of the IR spectrum along with the shift toward higher wavenumbers of the characteristic Al-N bands at 2351 cm⁻¹ and 665 cm⁻¹, respectively. This was related to the generation of a compressive stress inside films. In comparison to the optical constants of pure AlN films, the synthesized AlN:Cr films exhibited a smaller refractive index and showed a weak absorption throughout the 300-800 nm spectral region, characteristic to amorphous AlN structure.     

Amorphous to crystalline phase transition in pulsed laser deposited silicon carbide

SiC thin films were grown on Si (1 0 0) substrates by excimer laser ablation of a SiC target in vacuum. The effect of deposition temperature (up to 950 °C), post-deposition annealing and laser energy on the nanostructure, bonding and crystalline properties of the films was studied, in order to elucidate their transition from an amorphous to a crystalline phase. Infra-red spectroscopy shows that growth at temperatures greater than 600 °C produces layers with increasingly uniform environment of the Si-C bonds, while the appearance of large crystallites is detected, by X-ray diffraction, at 800 °C. Electron paramagnetic resonance confirms the presence of clustered paramagnetic centers within the sp² carbon domains. Increasing deposition temperature leads to a decrease of the spin density and to a temperature-dependent component of the EPR linewidth induced by spin hopping. For films grown below 650 °C, post-deposition annealing at 1100 °C reduces the spin density as a result of a more uniform Si-C nanostructure, though large scale crystallization is not observed. For greater deposition temperatures, annealing leads to little changes in the bonding properties, but suppresses the temperature dependent component of the EPR linewidth. These findings are explained by a relaxation of the stress in the layers, through the annealing of the bond angle disorder that inhibits spin hopping processes.     

Effect of temperature on pulsed laser deposition of HgCdTe films

HgCdTe thin films have been deposited on Si(1 1 1) substrates at different substrate temperatures by pulsed laser deposition (PLD). An Nd:YAG pulsed laser with a wavelength of 1064 nm was used as laser source. The influences of the substrate temperature on the crystalline quality, surface morphology and composition of HgCdTe thin films were characterized by X-ray diffraction (XRD), selected area electron diffraction (SAED), atomic force microscopy (AFM) and energy dispersive X-ray spectroscopy (EDS). The results show that in our experimental conditions, the HgCdTe thin films deposited at 200 °C have the best quality. When the substrate temperature is over 250 °C, the HgCdTe film becomes thermodynamically unstable and the quality of the film is degraded.     

Effect of RF power on the optical and morphological properties of RF plasma polymerised linalyl acetate thin films

Thin films derived from linalyl acetate were fabricated using the Radio Frequency (RF) plasma polymerisation technique between RF power levels of 10 and 75 W. The optical properties of the films were investigated using spectroscopic ellipsometry and UV-vis spectroscopy between 200 and 1000 nm. An optical band gap of approximately 3 eV for all power levels was determined from Tauc plots. The surface morphology and hardness of the material were studied using AFM and nano-indentation respectively to determine the effect of RF power on the thin film properties. Smooth surfaces with an average roughness of approximately 0.2 nm with consistent morphology were obtained across all power levels, while hardness demonstrated a linearly increasing dependence on RF deposition power, with values ranging between 0.29 and 0.44 GPa. These studies indicate the ability to tailor film characteristics by varying the RF deposition power, and the potential for the films to be used within electronic devices as encapsulation layers, insulating layers, or as semiconducting layers with the introduction of charge carriers to the chemical structure of the material.     

Depth-profile investigations of triterpenoid varnishes by KrF excimer laser ablation and laser-induced breakdown spectroscopy

The ablation properties of aged triterpenoid dammar and mastic films were investigated using a Krypton Fluoride excimer laser (248 nm, 25 ns). Ablation rate variations between surface and bulk layers indicated changes of the ablation mechanisms across the depth profiles of the films. In particular, after removal of the uppermost surface varnish layers there was a reduction of the ablation step in the bulk that was in line with a significant reduction of carbon dimer emission beneath the surface layers as detected by laser-induced breakdown spectroscopy. The results are explicable by the generation of condensation, cross-linking and oxidative gradients across the depth profile of triterpenoid varnish films during the aging degradation process, which were recently quantified and established on the molecular level.     

Influence of deposition pressure on structural, optical and electrical properties of nc-Si:H films deposited by HW-CVD

Hydrogenated nanocrystalline silicon (nc-Si:H) thin films were deposited using HW-CVD technique at various deposition pressures. Characterisation of these films from Raman spectroscopy revealed that nc-Si:H thin films consist of a mixture of two phases, crystalline phase and amorphous phase containing small Si crystals embedded therein. We observed increase in crystallinity in the films with increase in deposition pressure whereas the size of Si nanocrystals was found ∼2 nm over the entire range of deposition pressure studied. The FTIR spectroscopic analysis showed that with increasing deposition pressure the predominant hydrogen bonding in the films shifts from, Si-H to Si-H₂ and (Si-H₂)_n complexes and the hydrogen content in the films was found in the range 6.2-9.3 at% over the entire range of deposition pressure studied. The photo and dark conductivities results also indicate that the films deposited with increasing deposition pressure get structurally modified. It has been found that the optical energy gap range was between 1.72 and 2.1 eV with static refractive index between 2.85 and 3.24. From the present study it has been concluded that the deposition pressure is a key process parameter to induce the crystallinity in the Si:H thin films using HW-CVD.