Preparation and characterization of iodine-doped mesoporous TiO2 by hydrothermal method

Iodine-doped mesoporous TiO₂ (I/TiO₂) was prepared by hydrothermal method, using tetrabutyl titanate as precursor, potassium iodate as iodine sources. The as-prepared I/TiO₂ catalysts were characterized by UV-vis, XRD, TEM, BET, TG/DTA, XPS and photoluminescence (PL) spectroscopy. Production of OH radicals on the I/TiO₂ surface was detected by the PL technique using terephthalic acid as a probe molecule. The effects of hydrothermal reaction temperature, calcination temperature and iodine doping content on the structure and properties of the catalysts were investigated. The results showed that iodine-doped TiO₂ calcinated at 300 °C have good anatase crystal. The optimal hydrothermal conditions have been determined to be that reaction temperature 120 °C, calcinated temperature 300 °C and added 1.16 mmol iodine dopants. The average particle size of I/TiO₂ synthesized under optimal condition (I-3 sample) is about 3.9 nm. The I-3 photocatalyst contains 100% anatase crystalline phase of TiO₂. BET specific surface area of I-3 sample is184.8 m² g⁻¹ and is 3.67 times that of pure TiO₂ (50.37 m² g⁻¹). Iodine in I/TiO₂ catalyst mainly exists in the form of I₂, and photoactivity of I/TiO₂ catalyst in visible light comes from photosensitize of I₂. I/TiO₂ catalysis shows very high efficiency for the degradation of phenol under visible light.     

The enhanced photocatalytic activity of CdS/TiO2 nanocomposites by controlling CdS dispersion on TiO2 nanotubes

CdS/TiO₂ nanocomposites were prepared via a simple wet chemical method, and characterized through X-ray diffraction (XRD) and transmission electron microscopy (TEM). Their ability to degrade Acid Rhodamine B was investigated under visible light irradiation. The results indicate that CdS/TiO₂ nanocomposite with a mass ratio of 4:1(TiO₂:CdS) showed high photocatalytic activity and the CdS loaded on TiO₂ nanotube surface exhibited a hexagonal phase. The dispersion of CdS on TiO₂ nanotube surface had an important effect on the degradation efficiency of pollutant, which provides a strategy for practical industry application.     

Structural, photochemical and photocatalytic properties of zirconium oxide doped TiO2 nanocrystallites

Composite photocatalysts composed of TiO₂ and ZrO₂ have been prepared via the sol-gel method. The as-prepared nanocomposites are characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), UV-vis spectrometry and fluorescence emission spectra. The results shows that TiO₂/ZrO₂ nanocomposites are composed of mainly anatase titania and tetragonal ZrO₂. Incorporating TiO₂ particles with ZrO₂ plays an important role in promoting the formation of nanoparticles with an anatase structure and leads to decreased fluorescence emission intensity. Most of the TiO₂/ZrO₂ nanocomposites exhibited comparable photocatalytic activity compared with commercial TiO₂ for the degradation aqueous methyl orange (MO) under ultraviolet irradiation, while the composite with Zr/Ti mass ratio of 15.2% shows the highest photocatalytic performances. Furthermore, the as-prepared nanocomposites can be reused with little photocatalytic activity loss. Without any further treatment besides rinsing, the photocatalytic activity of TiO₂/ZrO₂ (15.2%) composites is still higher than after five-cycle utilization.     

Effect of surface species on Cu-TiO2 photocatalytic activity

The Cu-TiO₂ nanoparticles with different Cu dopant content were prepared by sol-gel method. The structure of the as-prepared catalysts and the surface species of Cu-TiO₂ were determined using X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and diffuse reflection spectroscopy (DRS). The relationship between the photocatalytic activity and the surface species of Cu-TiO₂ was revealed via the measurement of surface photovoltage spectroscopy (SPS) as well as the degradation of the rhodamine B (RhB). The experimental results suggest that the Cu-TiO₂ photocatalysts with appropriate content of Cu (about 0.06 mol%) possess abundant electronic trap, which effectively inhibits the recombination of photoinduced charge carriers, improving the photocatalytic activity of TiO₂. While at high Cu dopant region (>0.06 mol%), the excessive oxygen vacancies and Cu species can become the recombination centers of photoinduced electrons and holes. Meanwhile, at heavy Cu doping concentration, excessive P-type Cu₂O can cover the surface of TiO₂, which leads to decrease in the photocatalytic activity of photocatalyst. The photocatalytic experimental results are in good agreement with the conclusions of SPS measurements, indicating that there is a close relationship between the photocatalytic activity and the intensity of SPS spectra.     

Tunable photocatalytic selectivity of fluoropolymer PVDF modified TiO2

Fluoropolymer poly-vinylidene-fluoride modified TiO₂ (PVDF/TiO₂) were prepared via a simple chemisorption approach and characterized by thermo gravimetric analyse, transmission electron microscope, X-ray diffraction, X-ray photoelectron spectroscopy and photoluminescence spectra. The modified mechanism and the photocatalytic selectivity of the PVDF/TiO₂ were studied. The existence of Ti-F coordination bond on the interface between TiO₂ and PVDF was confirmed. For the PVDF modification, the photocatalytic degradation (PCD) of cationic dye was greatly enhanced, and the PCD of anionic dye was obviously inhibited. PVDF/TiO₂ shows high photocatalytic selectivity than that of TiO₂ by degrading mixed solution of cationic dyes MB and anionic dyes MO. The selectivity can be tuned by changing the PVDF modification amount.     

Preparation and characterization of amine-functionalized SiO2/TiO2 films for formaldehyde degradation

This paper investigated the gaseous formaldehyde degradation by the amine-functionalized SiO₂/TiO₂ photocatalytic films for improving indoor air quality. The films were synthesized via the co-condensation reaction of methyltrimethoxysilane (MTMOS) and 3-aminopropyltrimethoxysilane (APTMS). The physicochemical properties of prepared photocatalysts were characterized with N₂ adsorption/desorption isotherms measurement, X-ray diffraction (XRD) and Fourier Transform Infrared spectroscopy (FT/IR). The effect of amine-functional groups and the ratio of MTMOS/APTMS precursors on the formaldehyde adsorption and photocatalytic degradation were investigated. The results showed that the formaldehyde adsorption and photocatalytic degradation of the APTMS-functionalized SiO₂/TiO₂ film was higher than that of SiO₂/TiO₂ film due to the surface adsorption on amine sites and the relatively high of the specific surface area of the APTMS-functionalized SiO₂/TiO₂ film (15 times higher than SiO₂/TiO₂). The enhancement of the formaldehyde degradation of the film can be attributed to the synergetic effect of adsorption and subsequent photocatalytic decomposition. The repeatability of photocatalytic film was also tested and the degradation efficiency was 91.0% of initial efficiency after seven cycles.     

Surface effect of natural zeolite (clinoptilolite) on the photocatalytic activity of TiO2

The surface interaction between TiO₂ and natural zeolite, clinoptilolite, has been investigated by means of transmission electron microscope (TEM), atom force microscope (AFM), X-ray diffractometer (XRD), diffuse reflectance infrared Fourier transform (DRIFT) and far Fourier transform infrared ray (FTIR) spectroscopy. And the photocatalytic degradation (PCD) rate of methyl orange (MO), a model of recalcitrant azo dye, in aqueous system has been measured to compare the photocatalytic activities of different photocatalysts. A model has been carried out to explain the incorporation between TiO₂ particles and natural zeolite. The results show that the TiO₂ particles loaded on zeolite are 50 nm or so, smaller than the pure one, and combine with zeolite via chemical force. Since the reserved adsorption ability and the existence of electron trapper, the TiO₂-zeolite performed more efficient at low initial concentration and in the later period of PCD process, as compared with pure TiO₂ nanopowders.     

Effects of surface-modification with Bi2O3 on the thermal stability and photoinduced charge property of nanocrystalline anatase TiO2 and its enhanced photocatalytic activity

Bi₂O₃ surface-modified TiO₂ nanoparticle has been synthesized by sol-hydrothermal processes, followed by post-treatment with an appropriate amount of bismuth nitrate solution, and also characterized by XRD, Raman, BET, TEM, FT-IR, XPS, UV-vis DRS and SPS techniques. The effects of the surface-modification with Bi₂O₃ on the thermal stability, photoinduced charge separation and photocatalytic activity for degrading rhodamine B (or phenol) under ultraviolet (or visible) irradiation are investigated in detail, along with their relationships and the activity enhancement mechanisms are also suggested. The results show that the modification with Bi₂O₃ can improve the thermal stability of the as-prepared anatase crystallites, consequently enhancing the anatase crystallinity so as to promote the photoinduced charge separation. And the modification with Bi₂O₃ also extends the optical response range. It can be concluded that the activity enhancement of surface-modified TiO₂ is mainly attributed to the increase in the photoinduced charge separation rate and to the extent of the optical response range, compared with un-modified ones. Moreover, the inhibition phase transformation mechanism related to Bi₂O₃ is suggested.     

Synthesis of fluorinated TiO2 hollow microspheres and their photocatalytic activity under visible light

Fluorinated TiO₂ hollow microspheres with three-dimensional hierarchical architecture were prepared by solvothermally treatment using solid microspheres as precursor. The obtained solid and hollow TiO₂ microspheres were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), Brunauer-Emmett-Teller (BET), X-ray photoelectron spectroscopy (XPS), UV-Vis diffuse reflectance spectrum (DRS) and photoluminescence (PL) spectra. The photocatalytic activity of as-prepared solid and hollow TiO₂ microspheres was determined by degradation of methyl orange (MO) under visible light irradiation. The results showed that the surface fluorination, the existence of accessible mesopores channels, and the increased light harvesting abilities could remarkably improve the photocatalytic activity of TiO₂ hollow microspheres.     

Enhancement of the photocatalytic activity of TiO2 nanoparticles by surface-capping DBS groups

TiO₂ nanoparticles capped with sodium dodecylbenzenesulfonate (DBS) are synthesized by a sol-hydrothermal process using tetrabutyl titanate and DBS as raw materials. The effects of surface-capping DBS on the surface photovoltage spectroscopy (SPS), photoluminescence (PL) and photocatalytic performance of TiO₂ nanoparticles are principally investigated together with their relationships. The results show that the surface of TiO₂ nanoparticles can be well capped by DBS groups while the pH value and added DBS amount are controlled at 5.0 and 2% of TiO₂ mass weight, respectively, and the linkage between DBS groups and TiO₂ surfaces is mainly by means of quasi-sulphonate bond. The intensities of SPS and PL spectra of TiO₂ obviously decrease after DBS-capping, while the activity can greatly increase during the photocatalytic degradation of Rhodamine B (RhB) solution, which are mainly attributed to the electron-withdrawing character of the DBS groups. Moreover, the enhancement of photocatalytic activity of DBS-capped TiO₂ is also related to the increase in the capability for adsorbing RhB.     

Room temperature ferromagnetism in vacuum-annealed TiO2 thin films

Thin films of pure TiO₂ have been prepared using both spin-coating and sputter-deposition techniques on sapphire and quartz substrates. The structural characteristics of the films have been investigated in detail using Raman spectroscopy and high-resolution transmission electron microscopy (HRTEM). When annealed in vacuum, all films demonstrate room temperature ferromagnetism, while the air-annealed samples show much smaller, often negligible, magnetic moments. The magnetization of the vacuum-annealed sputtered samples depends on film thickness, with the volume magnetization decreasing monotonically with increasing thickness. Furthermore, the magnetization per unit area also decreases slightly with increasing film thickness. These results suggest that ferromagnetism in the vacuum-annealed TiO₂ films is mediated by surface defects or interfacial effects, but does not arise from stoichiometric crystalline TiO₂.     

Design and fabrication of a TiO2/nano-silicon composite visible light photocatalyst

Nano-silicon (nc-Si) was utilized as the charges generator to promote the photocatalytic and super-hydrophilic reactivity of TiO₂ film under visible light irradiation. The photocatalytic ability of TiO₂/nc-Si composite photocatalyst was evaluated by a set of experiments to photodecompose 100 ppm methylene blue (MB) in aqueous solution. And the super-hydrophilic property was characterized by measuring the water droplet contacts angle, under visible light irradiation in atmospheric air and at room temperature. Under 100 mW/cm² visible light irradiation, the droplet contact angles were reduced to 0° within 4 h with nc-Si charge generator. Additionally, the rate constant of MB photo-degradation was promoted 6.6 times.     

Efficient one-pot synthesis of Ag nanoparticles loaded on N-doped multiphase TiO2 hollow nanorod arrays with enhanced photocatalytic activity

The simultaneous Ag loaded and N-doped TiO₂ hollow nanorod arrays with various contents of silver (Ag/N-THNAs) were successfully synthesized on glass substrates by one-pot liquid phase deposition (LPD) method using ZnO nanorod arrays as template. The catalysts were characterized by Raman spectrum, field-emission scanning electron microscopy (FESEM), high-resolution transmission electron microscope (HRTEM), ultraviolet-vis (UV-vis) absorption spectrum and X-ray photoelectron spectroscopy (XPS). The results suggest that AgNO₃ additive in the precursor solutions not only can promote the anatase-to-rutile phase transition, but also influence the amount of N doping in the samples. The photocatalytic activity of all the samples was evaluated by photodegradation of methylene blue (MB) in aqueous solution. The sample exhibited the highest photocatalytic activity under UV light illumination when the AgNO₃ concentration in the precursor solution was 0.03 M, due to Ag nanoparticles acting as electron sinks; When the AgNO₃ concentration was 0.07 M, the sample performed best under visible light illumination, attributed to the synergetic effects of Ag loading, N doping, and the multiphase structure (anatase/rutile).     

Preparation, characterization and visible-light photocatalytic activity of AgI/AgCl/TiO2

In this paper, a novel composite photocatalyst AgI/AgCl/TiO₂ was prepared by ion exchange method and characterized by XRD, SEM and UV-Vis spectrometry. The as-prepared AgI/AgCl/TiO₂ composites show much higher photocatalytic activity than AgCl/TiO₂ and AgI/TiO₂ under visible-light irradiation (λ > 400 nm) in the process of methyl orange (MO) degradation. When the molar percentage of AgI to initial AgCl is 20% (sample SE-20%), the maximal degradation efficiency of MO has reached 85.8% after irradiation for 120 min. The enhancement of photocatalytic activity of the composite photocatalyst AgI/AgCl/TiO₂ will be attributed to its good absorption in the visible-light region, especially low recombination rate of the electron-hole pairs based on the photoluminescence (PL) spectra investigation of AgI/AgCl/TiO₂ and the matching band structures of AgI, AgCl and TiO₂. The detection of reactive species by radical scavengers displays that O₂⁻ and H₂O₂ are the main reactive species for the degradation of MO under visible-light irradiation. Moreover, PL analysis by using terephthalic acid (TA) as a probe molecule further reveals that OH can be negligible for the degradation of MO.     

From anodic TiO2 nanotubes to hexagonally ordered TiO2 nanocolumns

We report on the formation of hexagonally ordered TiO₂ nanocolumnar layers by electrochemical oxidation in a fluoride containing electrolyte, using self-organizing nanotube formation conditions at elevated potentials and low temperatures. The influence of the substrate temperature on the nanocolumn morphology and composition is investigated and characterized by FE-SEM and EDX. The origin of these nanocolumns can be attributed to a thickening of the inner tube wall of the double wall structure of self-organized TiO₂ nanotubes. Furthermore, a transition from nanocolumnar to nanotubular structure can be established by changing the applied voltage or applying a post-immersion treatment.     

Photoelectrocatalytic degradation of organic contaminants at Bi2O3/TiO2 nanotube array electrode

In the current work, TiO₂ nanotube array was prepared via electrochemical anode method. Then the Bi₂O₃ nanoparticles were deposited onto the TiO₂ nanotube array via dip-coating method from an amorphous complex precursor. The crystal structures were characterized via X-ray diffraction analysis. Their surface textures were observed via electron-scanning microscope. The prepared composite array electrode exhibited high photoelectrocatalytic activities towards degrading organic contaminants under visible light irradiation. High photoelectrocatalytic activities were also exhibited under UV light irradiation. The catalytic mechanism was discussed based on the analysis of electrochemical and degradation kinetics results. It is suggested a P (Bi₂O₃)-N (TiO₂) junction was formed to increase the catalytic activates. The stability of the electrode materials was confirmed finally.     

Enhanced photocatalytic activity of TiO2 nano-structured thin film with a silver hierarchical configuration

TiO₂ sol-gels with various Ag/TiO₂ molar ratios from 0 to 0.9% were used to fabricate silver-modified nano-structured TiO₂ thin films using a layer-by-layer dip-coating (LLDC) technique. This technique allows obtaining TiO₂ nano-structured thin films with a silver hierarchical configuration. The coating of pure TiO₂ sol-gel and Ag-modified sol-gel was marked as T and A, respectively. According to the coating order and the nature of the TiO₂ sol-gel, four types of the TiO₂ thin films were constructed, and marked as AT (bottom layer was Ag modified, surface layer was pure TiO₂), TA (bottom layer was pure TiO₂, surface layer was Ag modified), TT (pure TiO₂ thin film) and AA (TiO₂ thin film was uniformly Ag modified). These thin films were characterized by means of linear sweep voltammetry (LSV), X-ray diffraction (XRD), scanning electron microscopy (SEM), electrochemical impedance spectroscopy and transient photocurrent (I_ph). LSV confirmed the existence of Ag⁰ state in the TiO₂ thin film. SEM and XRD experiments indicated that the sizes of the TiO₂ nanoparticles of the resulting films were in the order of TT > AT > TA > AA, suggesting the gradient Ag distribution in the films. The SEM and XRD results also confirmed that Ag had an inhibition effect on the size growth of anatase nanoparticles. Photocatalytic activities of the resulting thin films were also evaluated in the photocatalytic degradation process of methyl orange. The preliminary results demonstrated the sequence of the photocatalytic activity of the resulting films was AT > TA > AA > TT. This suggested that the silver hierarchical configuration can be used to improve the photocatalytic activity of TiO₂ thin film.     

The photocatalytic application and regeneration of anatase thin films with embedded commercial TiO2 particles deposited on glass microrods

Anatase thin films (<200 nm in thickness) embedding Degussa P25 TiO₂ were prepared by sol-gel method. TiO₂-anatase thin films were deposited on a fiberglass substrate and then ground to obtain glass microrods containing the composite films. The film structure was characterized using Raman spectroscopy, atomic absorption and UV-vis spectrophotometry, and atomic force microscopy. The photocatalytic activity of the composite films, calcined at 450 °C, and the regeneration of the activity under the same experimental conditions, were assessed using gas chromatography to study the photodegradation of phenol, an industrial pollutant, in water under 365 nm irradiation. The film with 15.0 wt.% of P25 TiO₂ was found to be more photoactive (54 ppm of degraded phenol at 6 h of illumination) than the other ones.     

Improvement in the photocatalytic activity of TiO2 by the partial oxidation of the C impurities

TiO₂ was treated by water in an ultrasonic bath, resulting in the enhancement of the photocatalytic activity for the decomposition of methylene blue under UV and visible light irradiation. No change in the crystallinity and optical properties of TiO₂ by the H₂O-treatment was observed. The X-ray photoelectron spectroscopy (XPS) and FT-IR data revealed that the C impurities were oxidized by this treatment, indicating that the change in the structure of the C impurities plays a pivotal role in the photocatalytic activity of TiO₂.     

Sunlight photocatalytic activity of CdS modified TiO2 loaded on activated carbon fibers

To improve the photocatalytic application performances of TiO₂, in this work, firstly CdS modified Degussa P25 TiO₂ (CdS/TiO₂) composites were prepared by two methods, sol-gel method and precipitation method. Next they, sol-gel-CdS/TiO₂ (sg-CdS/TiO₂) and precipitation-CdS/TiO₂ (pp-CdS/TiO₂), were loaded on activated carbon fibers (ACFs) by dip-coating method using the sodium carboxymethyl cellulose as adhesives. The composites were characterized by XRD, UV-vis absorbance spectra, SEM, EDS and BET. The photocatalytic activities under sunlight were investigated by the degradation of methylene blue. The results showed that CdS/TiO₂ composites were mainly composed of anatase-TiO₂ and little CdS cubic phases. The absorption wavelengths of sg-CdS/TiO₂ and pp-CdS/TiO₂ composites were extended to 590 nm and 740 nm, respectively. The absorption edge had a pronounced ‘red shift’. From EDS analysis, the elemental contents of CdS/TiO₂ were mainly Ti and O and a small quantity of S and Cd. CdS/TiO₂ loaded on ACFs were in the form of small clusters, but not very uniform; compared with the original ACFs, the surface area and pore volume of CdS/TiO₂/ACFs decreased slightly, respectively, while the average pore diameter was not changed. The photodegradation rate of methylene blue under sunlight with CdS/TiO₂/ACFs composites was markedly higher than that of P25-TiO₂/ACFs, and the effect of pp-CdS/TiO₂/ACFs composites was better than that of sg-CdS/TiO₂/ACFs, when irradiated for 180 min, and the photodegradation rate of methylene blue reached to 90.1%. The photodegradation kinetics of the methylene blue fitted with the Langmuir-Hinshelwood equation. The apparent reaction rate constants of sg-CdS/TiO₂/ACFs and pp-CdS/TiO₂ were 0.0105 min⁻¹ and 0.0146 min⁻¹, respectively, which were about 1.3-1.7 times as large as that of P25-TiO₂/ACFs.