Preparation and characterization of montmorillonite-silica nanocomposites: A sol-gel approach to modifying clay surfaces

Montmorillonite-silica nanocomposites were prepared by a sol-gel approach involving hydrolysis reaction of alkoxysilanes (TEOS) and subsequent condensation reaction with hydroxyl groups of the clay, resulting in the formation of the mesoporous silica network and silica nanoparticles covered or attached on the clay surfaces. According to X-ray diffraction (XRD), transmission electron microscopy (TEM), scanning electron microscopy (SEM) and nitrogen adsorption isotherms, the structure and surface properties of the sol-gel-modified clay can be controlled by varying the TEOS/clay mass ratio and/or adding trace amounts of acid as catalyst. In the case of acid-catalyzed procedures, large continuous mesoporous silica was covered on the clay surfaces, resulting in delamination of clay platelets in silica matrix at higher TEOS/clay ratio, and attaching of isolated mesoporous silica on the clay surface at lower TEOS/clay ratio, respectively. In the case of non-catalyzed procedures, silica nanoparticles were attached on the two-dimensional (2D) clay platelets, while the stack order of the clay was maintained regardless of the TEOS/clay ratios. This sol-gel modification approach combines the surface properties of mesoporous silica and nanoparticles with layered clay, while inheriting the structural properties of the pristine clay such as further intercalation with organic compounds and polymers.     

氧化锌纳米颗粒薄膜的近紫外电致发光特性研究

利用溶胶-凝胶法(sol-gel method)制备了ZnO纳米颗粒薄膜(ZnO nanoparticle film),并以此为发光层制备了结构为ITO/ZnO nanoparticle/MEH-PPV/LiF/Al的电致发光器件.通过调整器件发光层厚度,对器件的发光光谱和电学特性进行测试研究,发现该器件在一定的直流电压下可以得到以ZnO近紫外(中心波长390 nm)发光为主的电致发光光谱,显示出较好的ZnO近紫外电致发光特性.对该器件的发光机理进行了一定的研究,认为该器件的发光是基于载流子隧穿.     

Enhanced photoluminescence of ZnO-SiO2 nanocomposite particles and the analyses of structure and composition

Stable blue-green photoluminescent ZnO-SiO₂ nanocomposite particles exhibiting quantum efficiency as high as 34.8% under excitation at 360 nm were prepared using a spray-drying process from a feed solution that contained both luminescent ZnO nanoparticles synthesized by a sol-gel method and commercially-available SiO₂ nanoparticles. The effects of silica nanoparticle size and SiO₂-to-ZnO concentration ratio on the PL properties of the composite particles were investigated. The internal structure and chemical composition were investigated in detail using elemental mapping, which revealed that ZnO nanoparticles were well-dispersed within silica nanoparticle matrix. At a LiOH concentration of 0.23 M, the predicted ZnO crystallite diameter before and after spray drying was approximately constant at 3.3 and 3.6 nm, respectively. This result indicates that ZnO particle growth was inhibited and therefore the PL property of ZnO nanoparticles was stably preserved in the composite.     

Facile preparation of super-hydrophobic and super-oleophilic silica film on stainless steel mesh via sol-gel process

A super-hydrophobic and super-oleophilic silica film on stainless steel mesh was obtained by simple sol-gel method using tetraethoxysilane (TEOS) and methyltriethoxysilane (MTES) as precursors. The super-hydrophobic and super-oleophilic properties were achieved owing to the hierarchical structure of the silica film with methyl groups terminated domains constructed on the mesh. The effects of the particle size, molar ration of MTES/TEOS, molar concentration of TEOS and aging of the silica sol on the hydrophobicity of the silica film were discussed. With increasing the dimensional size of silica particle, molar ration of MTES/TEOS, molar concentration of TEOS and aging period, the hydrophobicity of the silica film can be enhanced due to the increase of the surface roughness or coverage of the methyl groups. Besides, diiodomethane droplet can spread out on the silica film within 6.71 s for the capillary force and intrinsic oleophilicity of the methyl groups.     

利用氟硅烷提高溶胶-凝胶SiO2增透膜的疏水性

 以正硅酸乙酯为前驱体，氨水为催化剂，采用溶胶 凝胶法制备了二氧化硅增透膜；通过自组装技术，用氟硅烷对膜层进行表面修饰，制得了疏水增透膜，克服了常规增透膜亲水的缺点。采用红外光谱、分光光度计、扫描探针显微镜和静滴接触角测量仪等测试手段分析了薄膜的特性。结果表明：疏水增透膜的峰值透光率为99.7％，疏水角为110°；氟硅烷自组装改性不影响二氧化硅增透膜的光学性能。     

Study of the luminescence of tris(2-thenoyltrifluoroacetonato)lanthanide(III) complexes covalently linked to 1,10-phenanthroline-functionalized hybrid sol-gel glasses

The solubility and uniform distribution of lanthanide complexes in sol-gel glasses can be improved by covalently linking the complexes to the sol-gel matrix. In this study, several lanthanide β-diketonate complexes (Ln=Nd, Sm, Eu, Tb, Er, Yb) were immobilized on a 1,10-phenanthroline functionalized sol-gel glass. For the europium(III) complex, a sol-gel material of diethoxydimethylsilane (DEDMS) with polymer-like properties was derived. For the other lanthanide complexes, the sol-gel glass was prepared by using a matrix of tetramethoxysilane (TMOS) and DEDMS. Both systems were prepared under neutral reaction conditions. High-resolution emission and excitation spectra were recorded. The luminescence lifetimes were measured.     

钌(Ⅱ)配合物有机改性溶胶-凝胶氧传感膜荧光行为的研究

本文考察了利用甲基硅氧烷（TMOS）和二甲基二甲氧基硅烷（DiMe-DMOS)为共先驱体制备的有机改性溶胶－凝胶（sol-gel）氧荧光繁感传感膜，比较了5种不同配体的Ru配合物在不同极性溶剂和sol-gel膜内的荧光行为，考察了膜极性的改变对Ru化合物荧光光谱的影响，以及氧对不同极性有机改性sol-gel包埋Ru化合物荧光猝灭的程度。研究结果表明，在sol-gel膜内，Ru化合物的荧光寿命都有不同程度的增加，同时对氧的猝灭程度增加。另外膜的极性对氧猝灭的程度也有很大的影响，增加膜的疏水性，将提高传感膜对氧浓度的响应。     

Microstructure and interfacial interaction of polyimide/silica hybrid nanocomposites prepared with 3-aminopropyltriethoxysilane

A series of polyimide (PI)-silica hybrid nanocomposites are prepared from 3,3′,4,4′biphenyltetracarboxylic dianhydride (BPDA)-4,4′-oxydianiline (ODA) polyamic acid (PAA) and tetraethoxysilane (TEOS) or tetramethoxysilane (TMOS) by the sol-gel process. 3-Aminopropyltriethoxysilane (3-APS) is used to enhance the interfacial interaction between polyimide and silica. The morphology, interfacial interaction, and properties of the hybrids are investigated using scanning electron microscope (SEM), UV-vis spectroscopy, atomic force microscope (AFM), Fourier transform infrared spectroscopy (FTIR), and thermogravimetric analysis (TGA). SEM and AFM images indicate that silica particles of ca. 45-55 nm size are uniformly distributed in polyimide matrices and that the interfacial interaction between PI and TEOS is better than that between PI and TMOS. The optical transparencies of the PI/TEOS hybrids are better than that of the PI/TMOS hybrids. FTIR spectra confirm the Si O Si bond as well as the conversion of PAA to polyimide and PI/silica hybrid films. The thermal stability is increased after incorporation of the silicas in the polyimide matrix.     

St?ber法制备二氧化硅薄膜反应动力学

通过研究正硅酸乙酯(TEOS)水解的反应动力学,推导出Stber法制备二氧化硅溶胶体系中反应时间与TEOS转化率关系的动力学公式。分析确定了合适的转化率,进而用于计算二氧化硅溶胶的理论最佳反应时间。同时,以正硅酸乙酯为硅源,采用溶胶凝胶法在氨水催化作用下制备了不同配比的二氧化硅溶胶,考察了氨和水的浓度对反应时间的影响,结果表明,两者浓度增大可以有效减少反应时间。通过成膜性检测确定制备过程中的最佳反应时间,并与理论计算得到的最佳反应时间进行比较,结果表明,两者一致,误差控制在5%以内,说明该动力学公式具有很好的适用性。 2012-06-01;修订日期:     

Sonochemical synthesis, photocatalytic activity and optical properties of silica coated ZnO nanoparticles

In this paper, we report the synthesis of silica coated ZnO nanoparticles by ultrasound irradiation of a mixture of dispersion of ZnO, tetraethoxysilane (TEOS), and ammonia in an ethanol-water solution medium. The silica coating layer formed at the initial TEOS/ZnO loading of 0.8 for 60 min ultrasonic irradiation was uniform and extended up to 3 nm from the ZnO surface as revealed from HR-TEM images. Silica coated ZnO nanoparticles demonstrated a significant inhibition of photocatalytic activity against photodegradation of methylene blue dye in aqueous solution. The effects of silica coating on the UV blocking property of ZnO nanoparticles were also studied.     

Highly crystalline bilayer electron transport layer for efficient conjugated polymer solar cells

Solution processed solar cells are a promising renewable energy technology due to the low fabrication costs. The most commonly used electron transport layer for solution processed organic solar cells is ZnO. However, sol-gel derived ZnO is amorphous, which limits interfacial charge transport. In this study, we demonstrate a ZnO bilayer, composed of a nanoparticle ZnO and sol-gel derived ZnO layer, as the electron transport layer in polymer solar cells incorporating the novel polymer poly [(5,6-difluoro-2,1,3-benzothiadiazol-4,7-diyl)-alt-(3,3‴-di (2-octyldodecyl)-2,2′; 5′,2″; 5″,2‴-quaterthiophen-5,5‴-diyl)] (PffBT4T-2OD). Compared with the single layer sol-gel ZnO, the bilayer displayed enhanced crystallinity. Consequently, the interfacial transport from the active layer was improved, as evidenced by dark J-V and PL spectroscopy measurements. Solar cells incorporating this bilayer ZnO layer achieved PCE values exceeding 10%, a relative improvement of 25% compared to the sol-gel ZnO devices.     

Synthesis and characterization of hydrophobic silica nanocomposites

Hydrophobically modified silica nanocomposites have been prepared using a low temperature sol-gel process. In this study, an alkyltriethoxysilane derivative, hexdecyltrimethoxysilane (HDTMS), was co-condensed with tetraethoxyorthosilicate (TEOS) with and without a cross-linking agent, 3-glycidoxypropyltrimethoxysilane (GPTMS), to produce the modified composites. The hydrophobic properties were determined using contact angle measurement. FESEM observations revealed a semispherical nanostructure of the composites with grain size of about 50-75 nm in diameter. The chemical modification was studied by FTIR and EDX, whereas the physicothermal properties were analyzed by DSC and TGA. These long-chain alkyl modified silica nanocomposites are promising materials for use in hydrophobic and water-resistant applications.     

钌(Ⅱ)配合物有机改性干凝胶的氧传感性能

采用溶胶-凝胶法以正硅酸乙酯(TEOS)和正辛基三乙氧基硅烷(Octyl-triEOS)为共先驱体制备了掺杂二氯化二联吡啶(二吡啶并[3,2-a 2,3-c]吩嗪)合钌(Ru-Dppz)的干凝胶.考察了Ru-Dppz在乙醇溶液和干凝胶内的荧光行为,发现在干凝胶中配合物的发射光谱较乙醇溶液中有明显蓝移.与固态本体配合物相比,干凝胶内Ru-Dppz的荧光寿命有明显增加.以Ru-Dppz为荧光指示剂的有机改性氧传感材料具有灵敏度高、响应时间短及稳定性好等优点.该复合材料中有机改性剂的加入提高了氧的通透性,降低了发光分子间的浓度自猝灭进而改善了材料传感的灵敏度.     

Spectroscopic study of sulforhodamine 640-doped sol-gel silica

The sol-gel process is a technique which provides a low-temperature route for the preparation of organic dye-doped porous silica glass. Extended UV transmission was observed for HCl-catalysed sol-gel silica. Properties of a solute may differ greatly between a free solution and that solution confined in pores of a sol-gel glass. Absorption and fluorescence properties of sulforhodamine 640-doped silica samples prepared by sol-gel process were investigated. In the TEOS-derived gel, the emission of the dye does not shift during aging but exhibits a large change during drying. The emission maximum of sulforhodamine 640 blue shifts was discussed as a function of increasing rigidity of the surrounding matrix.     

超低密度SiO2气凝胶的制备及成型研究

 以正硅酸乙酯(TEOS)为硅源，采用酸碱二步催化溶胶-凝胶法，结合超临界干燥技术制备了超低密度SiO₂气凝胶,最低密度为3.4 mg/cm³；进一步结合成型工艺，在解决了模具设计和脱模技术后制备了具有不同密度的柱状和微型套筒样品，密度10～50 mg/cm³。研究了水、催化剂、稀释剂对二步溶胶-凝胶过程的影响，获得了制备低密度SiO₂气凝胶的最佳条件。利用扫描电镜、孔径分布及比表面积测试仪等对SiO₂气凝胶微结构进行了研究。结果表明，获得的超低密度SiO₂气凝胶具有较好的纳米网络，平均孔径18.9 nm，还具有高比表面积898 9 m²/g。     

Organic-inorganic hybrid superhydrophobic surfaces using methyltriethoxysilane and tetraethoxysilane sol-gel derived materials in emulsion

By applying alkaline-catalyzed co-hydrolysis and copolycondensation reactions of tetraethoxysilane (TEOS) and methyltriethoxysilane (MTES) in organic siloxane modified polyacrylate emulsion (OSPA emulsion), we are able to demonstrate the potential for developing a sol-gel derived organic-inorganic hybrid emulsion for a superhydrophobic surface research. TEOS and MTES derived sol-gel moieties can be designed for a physical roughness and hydrophobic characteristic (Si-CH₃) of the hybrid superhydrophobic surface, while OSPA emulsion can be endowed for good film-forming property. The effect of formulation parameters on superhydrophobicity and film-forming property was analyzed. The water contact angle (WCA) on the sol-gel derived hybrid film is determined to be 156°, and the contact angle hysteresis is 5° by keeping the mole ratio of TEOS:MTES:C₂H₅OH:NH₃·H₂O:AMP-95 at 1:4:30:10:0.63 and the mass percentage of OSPA emulsion at 25%. The nanoparticle-based silica rough surface is observed as the mole ratio of MTES/TEOS at 4:1. The sol-gel derived organic-inorganic hybrid emulsion shows remarkable film-forming property when the mole ratio of MTES/TEOS reaches or exceeds 4:1. With the primer coating, the performance of superhydrophobic film achieve actual use standard. It reveals that this new procedure is an effective shortcut to obtain a superhydrophobic surface with potential applications.     

Red colored transparent PMMA-SiO2 hybrid films

Red colored transparent organic-inorganic hybrids films of a cross-linked polymethyl-methacrylate (PMMA) and silica were prepared via the sol-gel route using tetraethoxy-silane (TEOS) as precursor and a commercial organic red dye. 3-(Trimethoxysilyl) propyl methacrylate (TMSPM) was used to make compatible the organic and inorganic components of the precursor solution mixture. Four type of colored hybrid films were deposited using precursor solutions with the reactants molar ratio 1:0.5:1 for TEOS: TMSPM:MMA, respectively, and four different weight contents of the organic red dye. The hybrid films were studied by Fourier transform infrared spectroscopy, atomic force microscopy and optical transmission and reflection spectroscopy. The hardness of the films was determined from a pencil hardness test referred to ASTM Standard D 3363-92. The results showed that the colored hybrid films have a thickness of about 2 μm and consist of a homogeneous cross-linked organic-inorganic matrix with embedded dye molecules very well dispersed. The hardness of the hybrid films was enhanced with respect to that of the pure organic component. The AFM measurements showed very flat and smooth film surfaces with rms average roughness about 0.3 nm. The optical properties of the hybrid films including their color properties were determined from optical transmission and reflection spectroscopy. We found that the intensity of the color in the hybrid films and the corresponding color coordinates depend on the amount of red dye in the hybrid films. Photodegradation studies were performed by monitoring the optical density of the films as a function of the exposure time to illumination for several values of illumination intensity.     

有机掺杂溶胶-凝胶法制备pH敏感膜及其光谱响应的研究

使用四甲氧基硅烷（TMOS）和二甲基二甲氧基硅烷（DiMe-DMOS)为共先驱体，采用溶胶－凝胶的有机掺杂，制备对pH具有宽程响应的敏感膜。详细考察了包埋溴酚蓝和溴酚绿的敏感膜对pH的响应值、响应时间、泄漏和可逆性等响应性能指标，并进行了溴酚蓝和溴酚绿在水相与膜内吸收光谱的研究。     

单甲基原位改性SiO2疏水减反膜的制备与性能研究

 在碱性条件下通过TEOS和MTES的共水解缩聚反应制备了单甲基原位改性的SiO₂溶胶，并使用提拉法在K9玻璃基片上镀制了疏水减反膜。通过透射电镜（TEM）考察了镀膜溶胶的微结构，分别使用红外光谱（FTIR）分析了薄膜的组分，用原子力显微镜（AFM）观察了薄膜的表面形貌和起伏状况，用紫外可见光谱（UV-vis）考察了薄膜的减反射性能，用接触角仪测量了薄膜对水的接触角。并使用“R-on-1”的方式测量了薄膜在Nd:YAG激光（1 064 nm，1 ns）作用下的损伤阈值。结果表明，通过共水解缩聚反应可以把甲基引入镀膜溶胶簇团中，改善了溶胶簇团的网络结构，使薄膜得到相当好的疏水性能和更好的抗激光损伤性能，同时薄膜能保持较好的减反射性能。     

PVA–APTEOS/TEOS Hybrid Sol–Gel Pervaporation Membrane for Dehydration of Ethanol

Novel organic–inorganic hybrid membranes were prepared by co-hydrolysis and co-condensation reactions of aminopropyltriethoxysilane (APTEOS) and tetraethylorthosilicate (TEOS) in poly(vinyl alcohol) (PVA) aqueous solution. These sol–gel reactions make a silica nanoparticles network which cross-links the structure of membranes. As a result, swelling properties of the membranes change due to these cross-linking reactions. The relative molar content of APTEOS to (APTEOS + TEOS) was changed from 0.0 to 0.75. The effect of APTEOS to (APTEOS + TEOS) on morphology as well as pervaporation performance of the membranes for dehydration of ethanol was investigated. It was found out that the hybrid membranes with a certain mass ratio of 1:1 (APTEOS + TEOS to PVA) exhibit higher permselectivity and more permeation flux for dehydration of ethanol aqueous mixtures compared with the PVA–TEOS membranes. Because hydrolysis and condensation reactions of mixed silanes make smaller silica nanoparticles, the permeability properties of the membranes improve in comparison with those of the membranes prepared using a single silane.