Au island growth on a Si(1 1 1) vicinal surface

Au island nucleation and growth on a Si(1 1 1) 7 × 7 vicinal surface was studied by means of scanning tunneling microscopy. The surface was prepared to have a regular array of step bunches. Growth temperature and Au coverage were varied in the 255-430 °C substrate temperature range and from 1 to 7 monolayers, respectively. Two kinds of islands are observed on the surface: Au-Si reconstructed islands on the terraces and three-dimensional (3D) islands along the step bunches. Focusing on the latter, the dependence of island density, size and position on substrate temperature and on Au coverage is investigated. At 340 °C and above, hemispherical 3D islands nucleate systematically on the step edges.     

Temperature dependent low energy electron microscopy study of Ge growth on Si(1 1 3)

We investigated the initial Ge nucleation and Ge island growth on a Si(1 1 3) surface using low energy electron microscopy and low energy electron diffraction. The sample temperature was varied systematically between 380 °C and 590 °C. In this range, a strong temperature dependence of the island shape is observed. With increasing temperature the Ge islands are elongated in the direction. Simultaneously, the average island size increases while their density decreases. From the Arrhenius-like behaviour of the island density, a Ge adatom diffusion barrier height of about 0.53 eV is deduced.     

Influence of the surface-termination of hexagonal SiC(0 0 0 1) on the temperature dependences of Ge growth modes and desorption

With the aim of comparing initial Ge adsorption and desorption modes on different surface terminations of 4H-SiC(0 0 0 1) faces, 3 × 3, √3×√3R30° (R3) and 6√3×6√3R30° (6R3) reconstructions, of decreasing Si surface richness, have been prepared by standard surface preparation procedures. They are controlled by reflection high energy electron diffraction (RHEED), low energy electron diffraction and photoemission. One monolayer of Ge has been deposited similarly at room temperature on each of these three surfaces, followed by the same set of isochronal heatings at increasing temperatures up to complete Ge desorption. At each step of heating, the structural and chemical status of the Ge ad-layer has been probed. Marked differences between the Si- (3 × 3 and R3) and C-rich (6R3) terminations have been obtained. Ge wetting layers are only obtained up to 400 °C on 3 × 3 and R3 surfaces in the form of a 4 × 4 reconstruction. The wetting is more complete on the R3 surface, whose atomic structure is the closest to an ideally Si-terminated 1 × 1 SiC surface. At higher temperatures, the wetting layer stage transiets in Ge polycrystallites followed by the unexpected appearance on the 3 × 3 surface of a more ordered Si island structure. It denotes a Si clustering of the initial Si 3 × 3 excess, induced by the presence of Ge. A phase separation mechanism between Si and Ge prevails therefore over alloying by Ge supply onto a such Si-terminated 3 × 3 surface. Conversely, no wetting is obtained on the 6R3 surface and island formation of exclusively pure Ge takes place already at low temperature. These islands exhibit a better epitaxial relationship characterized by Ge(1 1 1)//SiC(0 0 0 1) and Ge〈1 1 −2〉//SiC〈1 −1 0 0〉, ascertained by a clear RHEED spot pattern. The absence of any Ge-C bond signature in the X-ray photoelectron spectroscopy Ge core lines indicates a dominant island nucleation on heterogeneous regions of the surface denuded by the 6R3 graphite pavings. Owing to the used annealing cycles, the deposited Ge amount desorbs on the three surfaces at differentiated temperatures ranging from 950 to 1200 °C. These differences probably reflect the varying morphologies formed at lower temperature on the different surfaces. Considering all these results, the use of imperfect 6R3 surfaces appears to be suited to promote the formation of pure and coherent Ge islands on SiC.     

Solid phase epitaxy of Ge films on CaF2/Si(1 1 1)

At room temperature deposited Ge films (thickness < 3 nm) homogeneously wet CaF₂/Si(1 1 1). The films are crystalline but exhibit granular structure. The grain size decreases with increasing film thickness. The quality of the homogeneous films is improved by annealing up to 200 °C. Ge films break up into islands if higher annealing temperatures are used as demonstrated combining spot profile analysis low energy electron diffraction (SPA-LEED) with auger electron spectroscopy (AES). Annealing up to 600 °C reduces the lateral size of the Ge islands while the surface fraction covered by Ge islands is constant. The CaF₂ film is decomposed if higher annealing temperatures are used. This effect is probably due to the formation of GeF_x complexes which desorb at these temperatures.     

Scaling behavior of island density in submonolayer growth of CaF2 on vicinal Si(1 1 1)

We have studied the scaling behavior of two-dimensional island density during submonolayer growth of CaF₂ on vicinal Si(1 1 1) surfaces using scanning tunneling microscopy. We have analyzed the morphology of the Si(1 1 1) surfaces where CaF₂ partial monolayers with coverages of about 0.1 monolayer are deposited at ∼600 °C. The number density of terrace nucleated islands increases with substrate terrace width l as ∼l⁴ in a low island density regime. This scaling behavior is consistent with predictions for the case of the irreversible growth of islands.     

Behavior of N atoms in atomic-order nitrided Si0.5Ge0.5(1 0 0)

Behavior of N atoms in atomic-order nitrided Si_0.5Ge_0.5(1 0 0) by heat treatment in Ar at 600 °C was investigated by X-ray photoelectron spectroscopy (XPS). For thermal nitridation by NH₃ at 400 °C, nitridation of surface Si atoms tends to proceed preferentially over nitridation of surface Ge atoms. It is also clear that, with the heat treatment, nitridation of Si atoms proceeds by transfer of N atoms from Ge atoms. Angle-resolved XPS results show that Ge fraction beneath the surface nitrided layer increases significantly at 600 °C compared to the initial surface. These results indicate that preferential nitridation of Si atoms at surface over Ge atoms induces Ge segregation beneath the surface nitrided layer at higher temperatures above 400 °C.     

Real time investigation of the growth of silicon carbide nanocrystals on Si(1 0 0) using synchrotron X-ray diffraction

The growth of silicon carbide nanocrystals on Si(1 0 0) is studied by synchrotron surface X-ray diffraction (SXRD) during annealing at high temperature. A chemisorbed methanol monolayer is used as carbon source, allowing to have a fixed amount of carbon atoms to feed the growth. At room temperature, minor changes in the 2 × 1 reconstruction of silicon are observed due to the formation of Si-O-CH₃ and Si-H bonds from methanol molecules. When annealed at 500 °C, carbon incorporation into the silicon leads only to local modifications of the surface structure. Above 600 °C, tri-dimensional silicon carbide nanocrystals growth takes place, together with surface roughening and sharp decrease of domain sizes of the 2 × 1 reconstruction. The different processes taking place at each temperature are clearly distinguished and identified during the real time SXRD measurements.     

Femtosecond pulsed laser deposition of Ge quantum dot growth on Si(1 0 0)-(2 × 1)

Ge quantum dots were grown on Si(1 0 0)-(2 × 1) by femtosecond pulsed laser deposition at various substrate temperatures using a femtosecond Ti:sapphire laser. In situ reflection high-energy electron diffraction and ex situ atomic force microscopy were used to analyze the film structure and morphology. The morphology of germanium islands on silicon was studied at different coverages. The results show that femtosecond pulsed laser deposition reduces the minimum temperature for epitaxial growth of Ge quantum dots to ∼280 °C, which is 120 °C lower than previously observed in nanosecond pulsed laser deposition and more than 200 °C lower than that reported for molecular beam epitaxy and chemical vapor deposition.     

Surface etching induced by Ce silicide formation on Si(1 0 0)

We investigate the temperature-dependent surface etching process induced by Ce silicide on Si(1 0 0) using scanning tunneling microscopy and X-ray photoelectron spectroscopy. We found that step edges on the Si(1 0 0) surface are gradually roughened due to the formation of Ce silicide as a function of substrate temperature. Unlike the Si(1 1 1) surface, however, terrace etching also occurs in addition to step roughening at 500 °C. Moreover, we found that Si(1 0 0) dimers are released and formed dimer vacancy lines because bulk diffusion of Ce silicide into Si(1 0 0) surface occurs the defect-induced strain at higher temperature (∼600 °C).     

Surface evolution and three-dimensional shape changes of SiGe/Si(0 0 1) islands during capping at various temperatures

The authors use a combination of atomic force microscopy and selective wet chemical etching of the Si capping layer to investigate both the surface and the three-dimensional SiGe/Si(0 0 1) island shape changes during capping at various temperatures. Different evolution paths are identified depending on the capping temperature. During the early stages of Si overgrowth at 450 °C, a moderate SiGe alloying occurs near the island apex. In the later stages, island burying begins through lateral growth of pyramid-like structures, which consist of pure Si. A comparison with previous overgrowth studies allows us to clarify the role of the initial island size in determining the surface evolution above buried islands. Island dissolution with material transfer to the wetting layer dominates upon capping at 580 °C. Finally, when the temperature during growth and capping is identical, the islands become flatter and wider indicating that the system starts to evolve towards an energetically preferred SiGe quantum well.     

Growth of (√3 × √3)-Ag and (1 1 1) oriented Ag islands on Ge/Si(1 1 1) surfaces

We have studied the growth of Ag on Ge/Si(1 1 1) substrates. The Ge/Si(1 1 1) substrates were prepared by depositing one monolayer (ML) of Ge on Si(1 1 1)-(7 × 7) surfaces. Following Ge deposition the reflection high energy electron diffraction (RHEED) pattern changed to a (1 × 1) pattern. Ge as well as Ag deposition was carried out at 550 °C. Ag deposition on Ge/Si(1 1 1) substrates up to 10 ML has shown a prominent (√3 × √3)-R30° RHEED pattern along with a streak structure from Ag(1 1 1) surface. Scanning electron microscopy (SEM) shows the formation of Ag islands along with a large fraction of open area, which presumably has the Ag-induced (√3 × √3)-R30° structure on the Ge/Si(1 1 1) surface. X-ray diffraction (XRD) experiments show the presence of only (1 1 1) peak of Ag indicating epitaxial growth of Ag on Ge/Si(1 1 1) surfaces. The possibility of growing a strain-tuned (tensile to compressive) Ag(1 1 1) layer on Ge/Si(1 1 1) substrates is discussed.     

Nanogroove formation during homoepitaxial Au electrodeposition on reconstructed Au( 1 1 1)

In situ scanning tunneling microscopy (STM) studies of homoepitaxial electrodeposition on Au(1 1 1) from hydrochloric acid solution reveal an unusual deposit morphology in the potential regime of the Au surface reconstruction, where the deposited Au islands are separated by nanoscale grooves with preferred widths of 6 and 12 nm. The formation of these structures is attributed to a hindered coalescence of the islands, caused by elastic energy contributions of the reconstructed bottom of the grooves.     

A structural parallel between Ge- and Si-induced 4 × 4 and 3 × 3 reconstructions on SiC(0 0 0 1) drawn from comparative RHEED oscillations

The initial Ge growth stages on a (√3 × √3)R30°-reconstructed SiC(0 0 0 1) surface (√3) have been studied using a complete set of surface techniques such as reflection high energy electron diffraction (RHEED), low energy electron diffraction (LEED), atomic force microscopy (AFM) and photoemission and compared with similar Si surface enrichments in place of Ge. The investigations essentially focus on the wetting growth-regimes that are favoured by the use of the √3 surface as a starting substrate, this surface being the closest to a smooth and ideally truncated Si-terminated face of hexagonal SiC(0 0 0 1). Depending on temperature and Ge or Si coverages, varying surface organizations are obtained. They range from unorganized layer by layer growths to relaxed Ge(1 1 1) or Si(1 1 1) island growths, through intermediate attempts of coherent and strained Ge or Si surface layers, characterized by 4 × 4 and 3 × 3 surface reconstructions, respectively. RHEED intensity oscillation recordings, as a function of Ge or Si deposited amounts, have been particularly helpful to pinpoint the limited (by the high lattice mismatch) existence domains of these interesting coherent phases, either in terms of formation temperature or surface coverages. Prominently comparable data for these two Ge- and Si-related reconstructions allow us to propose an atomic model for the still unexplained Ge-4 × 4 one. It is based on a same local organization in trimer and ad-atom units for the Ge excess as admitted for the Si-excess of the 3 × 3 surface, the higher strain nevertheless favouring arrangements, for the Ge-units, in 4 × 4 arrays instead of 3 × 3 Si ones. Admitting such models, 1.25 and 1.44 monolayers of Ge and Si, should, respectively, be able to lie coherently on SiC, with respective lattice mismatches near 30% and 25%. The experimental RHEED-oscillations values are compatible with such theoretical ones. Moreover, these RHEED coverage determinations (for layer completion, for instance) inform us in turn about the initial Si richness of the starting √3 reconstruction and help us to discriminate between earlier contradictory atomic models proposed in the literature.     

Fabrication of uniform Au silicide islands on the Si(1 1 1)-(7 × 7) substrate

The Au silicide islands have been fabricated by additional deposition of Au on the prepared surface at 270 °C where the Si islands of magic sizes were formed on the Si(1 1 1)-(7 × 7) dimer-adatom-stacking fault substrate. The surface structure on the Au silicide islands shows the Au/Si(1 1 1)-√3 × √3 reconstructed structure although the substrate remains 7 × 7 DAS structure. The size of the Au silicide islands depends on the size distribution of the preformed Si islands, because the initial size and shape of the Si islands play important roles in the formation of the Au silicide island. We have achieved the fabrication of the Au silicide islands of about the same size (∼5 nm) and the same shape by controlling the initial Si growth and the additional Au growth conditions.     

Bimodal growth of manganese silicide on Si(1 0 0)

Two different growth modes of manganese silicide are observed on Si(1 0 0) with scanning tunneling microscopy. 1.0 and 1.5 monolayer Mn are deposited at room temperature on the Si(1 0 0)-(2 × 1) substrate. The as-grown Mn film is unstructured. Annealing temperatures between room temperature and 450 °C lead to small unstructured clusters of Mn or Mn_xSi_y. Upon annealing at 450 °C and 480 °C, Mn reacts chemically with the Si substrate and forms silicide islands. The dimer rows of the substrate become visible again. Two distinct island shapes are found and identified as MnSi and Mn₅Si₃.     

Growth of Ge islands on prepatterned Si (0 0 1) substrates

We report on the growth and properties of Ge islands grown on (0 0 1) Si substrates with lithographically defined two-dimensionally periodic pits. After thermal desorption and a subsequent Si buffer layer growth these pits have an inverted truncated pyramid shape. We observe that on such prepatterned substrates lens-like Ge-rich islands grow at the pit bottoms with less Ge deposition than necessary for island formation on flat substrates. This is attributed to the aggregation of Ge at the bottom of the pits, due to Ge migration from the pit sidewalls. At the later stages of growth, dome-like islands with dominant {1,1,3} or {15,3,23}, or other high-index facets [i.e. {15,3,20} facets] are formed on the patterned substrates as shown by surface orientation maps using atomic force microscopy. Furthermore, larger coherent islands can be grown on patterned substrates as compared to Ge deposition on flat ones.     

Effects of electronic confinement and substrate on the low-temperature growth of Pb islands on Si(1 0 0)-2 × 1 surfaces

The growth of Pb films on the Si(1 0 0)-2 × 1 surface has been investigated at low temperature using scanning tunneling microscopy. Although the orientation of the substrate is (1 0 0), flat-top Pb islands with (1 1 1) surface can be observed. The island thickness is confined within four to nine atomic layers at low coverage. Among these islands, those with a thickness of six layers are most abundant. Quantum-well states in Pb(1 1 1) islands of different thickness are acquired by scanning tunneling spectroscopy. They are found to be identical to those taken on the Pb(1 1 1) islands grown on the Si(1 1 1)7 × 7 surface. Besides Pb(1 1 1) islands, two additional types of Pb islands are formed: rectangular flat-top Pb(1 0 0) islands and rectangular three-dimensional (3D) Pb islands, and both their orientations rotate by 90° from a terrace to the adjacent one. This phenomenon implies that the structures of Pb(1 0 0) and 3D islands are influenced by the Si(1 0 0)-2 × 1 substrate.     

Germanium growth on Br-terminated Si(1 0 0)

The consequences of Ge deposition on Br-terminated Si(1 0 0) were studied with scanning tunneling microscopy at ambient temperature after annealing at 650 K. One monolayer of Br was sufficient to prevent the formation of Ge huts beyond the critical thickness of 3 ML. This is possible because Br acts as a surfactant whose presence lowered the diffusivity of Ge adatoms. Hindered mobility was manifest at low coverage through the formation of short Ge chains. Further deposition resulted in the extension and connection of the Ge chains and gave rise to the buildup of incomplete layers. The deposition of 7 ML of Ge resulted in a rough surface characterized by irregularly shaped clusters. A short 800 K anneal desorbed the Br and allowed Ge atoms to reorganize into the more energetically favorable “hut” structures produced by conventional Ge overlayer growth on Si(1 0 0).     

Surface composition and structure of palladium ultra-thin films deposited on Ni(1 1 1)

Ultra-thin palladium films deposited on the Ni(1 1 1) surface were characterized by X-ray photoelectron spectroscopy (XPS), low-energy electron diffraction (LEED) and X-ray photoelectron diffraction (XPD). For low coverage, LEED shows a (1 × 1) pattern similar to that of the substrate. For intermediate coverage, the LEED pattern displays extra spots around the main (1 × 1) spots, resembling a Moiré coincidence pattern, probably associated with the formation of Pd bi-dimensional islands oriented in different directions on the Ni(1 1 1) surface. The results obtained by XPS and XPD corroborate this finding. The LEED pattern displays this structure up to 500 °C. Annealing at 650 °C brings back the (1 × 1) pattern, which is associated with a Pd island coalescence and alloy formation by Pd diffusion in the first atomic layers of the Ni(1 1 1). In this paper we present a detailed study of this surface structure via a comparison between XPD experiment and theory.     

Cooperative growth of nano-islands on Si(1 0 0) surface

By setting up two low temperature regions on a terrace of a vicinal Si(1 0 0)-2 × 1 surface, we have studied growth of nano-islands in the two regions using a kinetic Monte Carlo simulation. At first two islands are formed and grow independently without any supply of atoms from the outside. As the growth proceeds further, two islands are connected with each other by forming a bridge region. After the connection, the growth changes dramatically showing a competitive mode in one stage and a cooperative mode in the other. Two islands grow cooperatively in a sense that a larger island ceases to grow and waits until the size of the other smaller island becomes similar to that of the larger one. When two islands become similar in size, one of the islands grows faster than the other competitively, by accumulating atoms from then smaller one. The origin of the growth mode is analyzed.