Relative humidity sensor based on SMS fiber structure with polyvinyl alcohol coating

A novel relative humidity (RH) sensor based on single-mode–multimode–single-mode (SMS) fiber structure is presented. The sensors are created through coating a thin layer of polyvinyl alcohol (PVA) on the multimode fiber deleted the cladding trough HF solution cauterization as the sensitive cladding film, whose refractive index varies as a function of humidity level. Due to the SMS fiber structure's sensitivity to ambient refractive index, the transmission spectra of SMS fiber structure coated PVA film are modified under exposure to different ambient humidity levels ranging from 30% to 80% RH. The related numerical simulations of transmission spectra of SMS fiber structure with different surrounding refractive index are also proposed. The sensitive of the RH measurement of 0.09 nm/% RH in the range from 30% to 80% RH is experimentally achieved. Meanwhile the intensity of wavelength at 1543 nm is decreasing as the humidity increasing. The experimental results obtained are consistent with the conclusion obtained by numerical simulating.     

基于Nafion-结晶紫传感膜的光纤湿度传感器研究

通过研究基于荧光和可见光吸收的两种湿度传感方法,从数种湿度分子探针中优选出结晶紫为分子识别器,包埋于Nafion溶胶中,制备成基于可见光吸收原理的光纤化学湿度传感膜。该传感膜与电荷耦合二极管阵列检测器等构成的光纤湿度传感器,于640 nm波长处对30%～100%范围内的相对湿度(relative humidity, RH)具有较快的响应时间(＜2 min)、较高的灵敏度(≤5%RH)、选择性和良好的可逆性(RSD≤2.6%)。     

SiO2 passivation film effects on microwave characteristics of YBa2Cu3O7−x-based resonators

SiO₂ film coated as a passivation layer for YBa₂Cu₃O_7−x (YBCO)-based microwave devices is investigated by measuring the microwave characteristics of microstrip line resonators. The SiO₂ film is deposited with its 0.3 to 0.4 μm thickness by a sputtering method using Ar + 30%O₂ plasma. These deposition conditions do not degrade the microwave characteristics and the critical temperature (T_c). Next, the SiO₂ film coated resonators are compared with the uncoated ones for two kinds of degradation conditions: a 200°C annealing in air, and an exposure to air at 85°C and 85% RH (relative humidity). We find that the SiO₂ passivation film prevents the YBCO thin film from the surface degradation and reacting with water.     

Humidity sensor based on localized surface plasmon resonance of multilayer thin films of gold nanoparticles linked with myoglobin

Layer-by-layer self-assembled multilayer thin films of gold nanoparticles (GNPs) linked with myoglobin (Mb) show substantial sensitivity to humidity at room temperature according to measurements of localized surface plasmon resonance (LSPR) absorption that relies on the interparticle interaction present in the film. The sensor response is reversible, with response and recovery times as low as 5 s. The sensing mechanism is as follows: as the ambient humidity changes, Mb molecules change their size, making the GNP-to-GNP spacing and thereby the interparticle interaction change; the change in the interparticle interaction causes a change in the LSPR absorption of the multilayer thin film. We found that the LSPR band of the multilayer thin film was almost insensitive to both the surrounding refractive index and the adlayer thickness, rendering the multilayer-film-based humidity sensor highly immune to ambient disturbances.     

硅纳米孔柱阵列及其四氧化三铁复合薄膜的湿敏电容特性研究

报道了硅纳米孔柱阵列（Si-NPA），Fe₃O₄复合的Si-NPA（Fe ₃O₄/Si-NPA）两种薄 膜材料的制备方法并对其形貌和结构进行了表征，研究了其电容湿度传感特性.结果表明，S i-NPA，Fe₃O₄/Si-NPA均为微米/纳米结构复合体系.当环境相对湿 度从11％上升到95％ 时，采用100 Hz的信号频率进行测试，以Si-NPA和Fe₃O₄/Si-NPA 为电介质材料制成的湿 敏元件的电容增加值分别为起始值的1500％和5500％；采用1000 Hz的信号频率测试时，则 分别为起始值的800％和12000％，显示出两种材料较高的湿度灵敏性和较强的绝对电容输出 信号强度.同时，在升湿和降湿过程中，Si-NPA，Fe₃O₄/Si-NPA都 具有较快的响应速度 ，其响应时间分别为15 s，5 s和20 s，15 s.文章结合材料的形貌和结构特性对其物理机理 进行了分析.上述结果表明，Si-NPA无论是直接作为湿度薄膜传感材料还是作为复合薄膜湿 度传感材料的衬底都具有很好的前景. 关键词： 硅纳米孔柱阵列 3O₄')" href="#">Fe₃O₄ 湿度电容传感特性     

Optical fiber humidity sensor based on evanescent-wave scattering

The phenomenon of evanescent-wave scattering (EWS) is used to design an optical-fiber humidity sensor. Porous solgel silica (PSGS) coated on the surface of a silica optical-fiber core scatters evanescent waves that penetrate the coating layer. Water molecules in the gas phase surrounding the optical fiber can be absorbed into the inner surface of the pores of the porous silica. The absorbed water molecules form a thin layer of liquid water on the inner surface of the porous silica and enhance the EWS. The amount of water absorbed into the PSGS coating is in dynamic equilibrium with the water-vapor pressure in the gas phase. Therefore the humidity in the air can be quantitatively determined with fiber-optic EWS caused by the PSGS coating. The humidity sensor reported here is fast in response, reversible, and has a wide dynamic range. The possible interference caused by EWS to an optical-fiber gas sensor with a reagent-doped PSGS coating as a transducer is also discussed.     

光纤SPR湿敏传感器及其共振光谱特性研究

提出并研制了基于光纤SPR传感探针的新型湿敏传感器。首先研究了光纤SPR传感探针对环境湿度变化的敏感特性,在此基础上提出在光纤SPR传感探针表面增覆不同厚度且具有水分子吸附功能的PVA薄膜来实现环境相对湿度的监测。研究结果表明,增覆双层PVA薄膜的光纤SPR传感探针在高湿区具有较好监测效果,其共振强度对应的相对湿度测量灵敏度达到1.59%/%RH,较光纤SPR探针呈现显著提高。而增覆单层PVA薄膜的光纤SPR传感探针在高湿区共振波长对应的相对湿度监测灵敏度达到2.411nm/%RH。此外所提出的新型光纤SPR湿敏探针在PVA薄膜失效后经过特殊工艺处理仍可重复镀膜使用。     

Fiber-optic humidity sensor based on an air-gap long period fiber grating

In this paper, we propose a novel high-sensitivity fiber-optic humidity sensor based on a calcium chloride thin film to be coated on an air-gap long-period grating fabricated (AG-LPG) by combining the fiber side-polishing and fiber etching methods. When the surrounding refractive index of the air-gap long-period grating is changed by a change in humidity, the grating resonant wavelength is considered varied. Experimental results indicate that humidity can be detected by this sensing mechanism and has a high sensitivity of about 1.36 nm/1%RH.     

Graphene/LiNbO3 surface acoustic wave device based relative humidity sensor

This study described relative humidity (RH) sensing using a graphene/128° YX LiNbO₃ surface acoustic wave (SAW) device. The resonant frequency of the device decreased in a two-stage manner as the RH increased. For a low RH range (RH < 50%), a frequency downshift of 1.38 kHz per 1% RH change was observed. This was attributed to mass loading of the SAW propagation surface due to the adsorption of water molecules by the graphene surface. For a high RH range (RH > 50%), a frequency downshift of 2.6 kHz per 1% RH change was obtained, which was due to the change in elastic grapheme properties. The mass loading effect of the water layer was less effective at high temperature, resulting in a lower temperature coefficient of resonant frequency (TCF).     

Enhanced-performance relative humidity sensor based on MOF-801 photonic crystals

We proposed an enhanced-performance relative humidity (%RH) nano-sensor based on MOF-801/TiO₂ one-dimensional photonic crystals (1DPC). The maximum reflectance-peak wavelength of it shifted obviously in the range of 20%-90% under varying %RH levels, due to the highly moisture-sensitive MOF-801 film in the 1DPC structure. It was demonstrated that the linear spectrum sensitivity of the MOF-801/TiO₂ %RH 1DPC sensor is exceeding 119 pm/%RH from 20%RH to 90% RH, and the sensitivity of reflection power variations exhibits 1.34 dB/%RH with the resolvable relative humidity variation less than 0.1%RH at 15°C. Meanwhile, the sensor shows a fast optical response time less than 100 ms with exceptional repeatability and reliability, which promises successful measurements of human respiration. Moreover, the sensor performance on the structure of 1DPC is investigated, representing a tradeoff between the sensing sensitivity and response time.     

The enhancement of humidity sensing performance based on Eu-doped ZnO

In this work, a high performance impedance-type humidity sensor based on Europium-doped ZnO with abundant surface oxygen vacancy defects was synthesized by sol-gel method. Response of the Eu-doped ZnO with different molar ratio were investigated by exposing them to humidity environments in wide range of 11–95% RH at room temperature. The Eu-doped ZnO (2?mol%) exhibits a three orders impedance change, along with short response/recovery time (5?s/19?s), low hysteresis and best linearity. Complex impedance spectra indicates that dopant Eu can enhance humidity sensing performance of ZnO, which is resulted from the introduction of Eu³⁺ ions into ZnO structure to produce more defects of surface oxygen vacancy and more active sites on the surface of ZnO. The results show that this is a feasible method to achieve high humidity sensing performance by Eu doped ZnO, which make it a promising candidate for humidity sensing materials and broaden the use of ZnO materials.     

Orange dye polyaniline composite based impedance humidity sensors

This study presents the fabrication and investigation of humidity sensors based on orange dye (OD) and polyaniline (PANI) composite films. A blend of 3 wt.% OD with 1 wt.% PANI was prepared in 1 ml water. The composite films were deposited on glass substrates between pre-deposited silver electrodes. The gap between the electrodes was 45 μm. The sensing mechanism was based on the impedance and capacitance variations due to the absorption/desorption of water vapor. It was observed that with the increase in relative humidity (RH) from 30% to 90%, the impedance decreases by 5.2 × 10 4 and 8.8 × 10 3 times for the frequencies of 120 Hz and 1 kHz, respectively. The impedance-humidity relationship showed a more uniform change compared to the capacitance-humidity relationship in the RH range of 30% to 90%. The consequence of annealing, measuring frequency, response and recovery time, and absorption-desorption behavior of the humidity sensor were also discussed in detail. The annealing resulted in an increase in sensitivity of up to 2.5 times, while the measured response time and recovery time were 34 s and 450 s, respectively. The impedance-humidity relationship was simulated.     

Water vapor adsorption onto activated carbons prepared from cattle manure compost (CMC)

Activated carbons were prepared from cattle manure compost (CMC) using zinc chloride activation. The structural and surface chemical characteristics of CMC-based activated carbons were determined by N₂ adsorption-desorption and Boehm titration, respectively. The water vapor adsorption properties of the prepared activated carbons with various pore structure and surface nature were examined, and the mechanism of water adsorbed onto activated carbon was also discussed. The results show that the adsorption of water vapor on carbons begins at specific active sites at low relative humidity (RH), followed by micropore filling at medium RH through the formation of pentamer cluster of water molecules in the narrow micropores. The water vapor adsorption capacity of activated carbon is predominantly dependent on its pore volume and surface area. Although capillary condensation is not the mechanism for water adsorption onto activated carbon, water can adsorb on narrow mesopore to some extent.     

Use of polyethylene glycol coatings for optical fibre humidity sensing

Humidity induced change in the refractive index and thickness of the polyethylene glycol (PEG) coatings are in situ investigated for a range from 10 to 95%, using an optical waveguide spectroscopic technique. It is experimentally demonstrated that, upon humidity change, the optical and swelling characteristics of the PEG coatings can be employed to build a plastic fibre optic humidity sensor. The sensing mechanism is based on the humidity induced change in the refractive index of the PEG film, which is directly coated onto a polished segment of a plastic optical fibre with dip-coating method. It is observed that PEG, which is a highly hydrophilic material, shows no monotonic linear response to humidity but gives different characteristics for various ranges of humidity levels both in index of refraction and in thickness. It undergoes a physical phase change from a semi-crystalline structure to a gel one at around 80% relative humidity. At this phase change point, a drastic decrease occurs in the index of refraction as well as a drastic increase in the swelling of the PEG film. In addition, PEG coatings are hydrogenated in a vacuum chamber. It is observed that the hydrogen has a preventing effect on the humidity induced phase change in PEG coatings. Finally, the possibility of using PEG coatings in construction of a real plastic fibre optic humidity sensor is discussed.     

The adsorption of water on clean and oxygen covered Cu(110)

The water adsorption on clean and oxygen precovered Cu(110) surfaces is studied by means of UPS, LEED, work function measurements and ELS. At 90 K on the clean surface molecular water adsorption is indicated by UPS. The H₂O molecules are bonded at the oxygen end and the H-O-H angle is increased as compared with the free molecule. In the temperature range between 90 and 300 K distorted H₂O molecules and adsorbed hydroxyl species (OH) are detected, which are desorbed at room temperature. On an oxygen covered surface hydroxyl groups are formed by dissociation of adsorbed water molecules at a lower temperature than on the clean surface. Multilayers of condensed water are found below 140 K in both cases.     

腔增强拉曼技术下的过饱和硫酸镁液滴蒸发动力学初探(英文)

本文通过单光束梯度力光学镊子-拉曼光谱系统,对硫酸镁单液滴随着相对湿度变化的反应进行了探究。当硫酸镁单液滴被光镊捕获之后,通过相对湿度的梯度变化探究了捕获液滴的蒸发动力学变化。发生在与耳语回音模相称波长的受激拉曼散射可以用来准确地确定液滴半径,因此,可以通过腔增强拉曼散射得到在不同湿度下处于平衡的液滴半径信息。本研究通过光镊对硫酸镁单液滴的实时监测,阐述了在某个相对湿度范围内该液滴的粒径变化的过程和结果,在此之前的硫酸镁吸湿性研究中没有先例。研究结果表明在相对湿度逐渐降低至40%的过程中硫酸镁液滴半径的变化速率逐渐变小。而当相对湿度低于40%时,液滴半径的减小会被严重抑制。这种现象表示在高浓度条件下硫酸镁液滴中水的蒸发扩散速率会降低。另一方面,在蒸发过程后的相对湿度上升过程中,硫酸镁液滴尺寸的增加明显缓慢于湿度增长速度。这一现象显示液滴的尺寸变化是不可逆的。说明胶态的形成导致了传质受阻,从而阻碍了液滴中水分子的交换。     

Electron-stimulated desorption of sodium atoms from germanium-coated tungsten

The yield of sodium atoms and energy distribution upon electron-stimulated desorption from sodium layers adsorbed on tungsten coated with a germanium thin film are measured under variations in the electron energy, the sodium coverage, and the surface temperature by the time-of-flight method with the use of a surface ionization detector. It is revealed that the electron-stimulated desorption of sodium atoms occurs via three channels, namely, a channel involving ionization of adsorbed sodium; the most efficient channel, which is produced by the germanium ionization; and a channel associated with the formation of tungsten excitons, which brings about desorption of NaGe molecules.     

Adsorption dynamics of double-stranded DNA on a graphene oxide surface with both large unoxidized and oxidized regions

The adsorption dynamics of double-stranded DNA (dsDNA) molecules on a graphene oxide (GO) surface are important for applications of DNA/GO functional structures in biosensors, biomedicine and materials science. In this work, molecular dynamics simulations were used to examine the adsorption of different length dsDNA molecules (from 4 bp to 24 bp) on the GO surface. The dsDNA molecules could be adsorbed on the GO surface through the terminal bases and stand on the GO surface. For short dsDNA (4 bp) molecules, the double-helix structure was partially or totally broken and the adsorption dynamics was affected by the structural fluctuation of short dsDNA and the distribution of the oxidized groups on the GO surface. For long dsDNA molecules (from 8 bp to 24 bp) adsorption is stable. By nonlinear fitting of the contact angle between the axis of the dsDNA molecule and the GO surface, we found that a dsDNA molecule adsorbed on a GO surface has the chance of orienting parallel to the GO surface if the length of the dsDNA molecule is longer than 54 bp. We attributed this behavior to the flexibility of dsDNA molecules. With increasing length, the flexibility of dsDNA molecules also increases, and this increasing flexibility gives an adsorbed dsDNA molecule more chance of reaching the GO surface with the free terminal. This work provides a whole picture of adsorption of dsDNA molecules on the GO surface and should be of benefit for the design of DNA/GO based biosensors.     

氧化石墨烯修饰倾斜光纤光栅10–12级重金属离子传感

设计了一种氧化石墨烯(GO)功能化的倾斜光纤光栅(TFBG)传感器,用于检测水溶液中的重金属离子.通过氧等离子体活化光纤表面,以及采用GO的无水乙醇分散液,避免了咖啡环效应引起的GO的团聚和堆叠,充分了暴露GO的表面和羧基.吸附重金属离子后, GO-TFBG传感器的透射光谱中的谐振峰发生红移,这是由GO向重金属离子的电子转移导致的有效折射率变化造成的.对Pb²⁺和Cd²⁺离子最低检测限可达到10^–10 mol/L (ng/L量级),相应灵敏度分别为0.426 d B/(nmol·L^–1)和0.385 d B/(nmol·L^–1)(2.06和3.43 d B/(μg·L^–1)).此外, GO-TFBG传感器具有出色的器件一致性, 5组传感器的传感性能稳定.本研究实现了GO纳米片在光纤表面的无团聚和均匀成膜,获得了具有超大表面积的GO并充分暴露表面羧基实现对重金属离子的吸附,利用了TFBG不同模式谐振对环境的高度敏感性,完成了对低浓度重金属离子的高灵敏度、可重...     

碱金属修饰的多孔石墨烯的储氢性能

基于第一性原理深入研究了碱金属原子(Li,Na,K)修饰的多孔石墨烯(PG)体系的储氢性能,并且通过从头算分子动力学模拟了温度对Li-PG吸附的H2分子稳定性的影响.研究结果表明,PG结构的碳环中心是碱金属原子最稳定的吸附位置,PG单胞最多可以吸附4个碱金属原子,Li原子被束缚最强,金属原子间无团聚的倾向;H2分子通过极化机制吸附在碱金属修饰的PG结构上,每个金属原子周围最多可以稳定地吸附3个H2分子;Li-PG对H2分子的吸附最强(平均吸附能为-0.246 eV/H2),Na-PG对H2分子的吸附较弱(平均吸附能为-0.129 eV/H2),K-PG对H2分子的吸附最弱(平均吸附能为-0.056 eV/H2),不适合用做储氢材料;在不考虑外界压强且温度为300 K的情况下,Li-PG结构可稳定地吸附9个H2分子,储氢量为9.25 wt.%;在400 K时,有7个吸附H2分子脱离Li-PG的束缚,在600-700 K的范围内,吸附H2分子全部脱离了Li-PG体系的束缚.