Preparation and visible light photocatalytic activity of mesoporous N, S-codoped TiO2(B) nanobelts

The mesoporous N, S-codoped TiO₂(B) nanobelts are synthesized via hydrothermal synthesis and post-treatment, and characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), N₂ adsorption-desorption measurements (BET), X-ray photoelectron spectra (XPS), and UV-vis diffuse reflectance spectra (DRS). The results show that the prepared samples are mesoporous structured and exhibit stronger absorption in the visible light region with red shift in the absorption edge. The photocatalytic activity of N, S-codoped mesoporous TiO₂(B) nanobelts is evaluated by the photocatalytic photodegradation of potassium ethyl xanthate (KEX) under visible light irradiation. It is found that the photocatalytic activity of the prepared samples increases with increasing the molar ratio of thiourea to Ti (R). At R = 3, the photocatalytic activity of the N, S-codoped TiO₂(B) sample TBLTS-3 reaches a maximum value. With further increasing R, the photocatalytic activity of the sample decreases. The high photocatalytic activity of N, S-codoped TiO₂(B) nanobelts can be attributed to the balance between strong absorption in visible light region and low recombination rate of electron/hole pairs.     

Mn,N共掺杂对锐钛矿相TiO2微观结构和性能的影响

采用第一性原理平面波超软赝势方法,系统研究了Mn,N共掺杂对锐钛矿相TiO₂的晶体结构、缺陷形成能、电子结构、光学性质以及氧化还原能力的影响.研究表明:Mn,N共掺杂锐钛矿相TiO₂后,TiO₂晶格发生了畸变,导致晶体八面体偶极矩增加,有利于光生电子-空穴对的有效分离;在TiO₂带隙中出现了杂质能级,使锐钛矿相TiO₂的光学吸收带边红移,可见光区的吸收系数明显增大,有利于光催化效率的提高;在不考虑 关键词： 2')" href="#">锐钛矿相TiO₂ 第一性原理 Mn和N共掺杂 光催化性能     

具有可见光活性的新型氮掺杂二氧化钛光催化剂的合成

设计合成了一种同时具有取代型与空隙型的氮掺杂二氧化钛,并采用X射线衍射、X光电能谱、漫反射光谱、光致发光谱、电子顺磁共振进行了表征．结果表明新型氮掺杂二氧化钛中氮不仅取代晶格氧原子存在取代型氮,而且与氧配位在二氧化钛晶格中形成空隙型氮．这种新型氮掺杂二氧化钛比取代型和空隙型氮掺杂二氧化钛具有更高的可见光光催化活性,且两种氮掺杂形式具有协同效应.     

(Mo + N) codoped TiO2 for enhanced visible-light photoactivity

A series of Ti_1−xMo_xO_2−yN_y samples were prepared by using sol-gel method and characterized by X-ray diffraction, transmission electron microscopy and UV-vis absorption spectroscopy. All Ti_1−xMo_xO_2−yN_y samples are anatase phase. It is found that Mo, N mono-doping can increase visible light absorption, while (Mo + N) co-doping can greatly enhance absorption in whole visible region. Results of our first-principles band structure calculations reveal that (Mo + N)-doping, especially passivated co-doping can increase the up-limit of dopant concentration and create more impurity bands in the band gap of TiO₂, which leads to a greatly increase of its visible-light absorption without a decrease of its redox potential. It reveals that (Mo + N) co-doped TiO₂ is promising for a photocatalyst with high photocalystic activity under visible light.     

Effect of N2 ion flux on the photocatalysis of nitrogen-doped titanium oxide films by electron-beam evaporation

Nitrogen-doped titanium oxide (TiO_xN_y) films were prepared with ion-assisted electron-beam evaporation. The nitrogen (N) incorporated in the film is influenced by the N₂ flux modulated by the N₂ flow rate through an ion gun. The TiO_xN_y films have the absorption edge of TiO₂ red-shifted to 500 nm and exhibit visible light-induced photocatalytic properties in the surface hydrophilicity and the degradation of methylene blue. The structures and states of nitrogen in the films are investigated by X-ray diffraction patterns (XRD), and X-ray photoelectron spectroscopy (XPS) and related to their visible light-induced photocatalytic properties. The results indicate that the substitutional N in anatase TiO₂ can induce visible light photocatalysis. The substitutional N is readily doped by the energetic nitrogen ions from the ion gun. The best photocatalytic activity is obtained at the largest N loading about 5.6 at.%, corresponding to the most substitutional N in anatase TiO₂. The film exhibits the degradation of methylene blue with a rate-constant (k) about 0.065 h⁻¹ and retaining 7° water contact angle on the surface under visible light illumination.     

Electronic and optical properties of pure and Mo doped anatase TiO2 using GGA and GGA+U calculations

Comparative GGA and GGA+U calculations for pure and Mo doped anatase TiO₂ are performed based on first principle theory, whose results show that GGA+U calculation provide more reliable results as compared to the experimental findings. The direct band gap nature of the anatase TiO₂ is confirmed, both by using GGA and GGA+U calculations. Mo doping in anatase TiO₂ narrows the band gap of TiO₂ by introducing Mo 4d states below the conduction band minimum. Significant reduction of the band gap of anatase TiO₂ is found with increasing Mo doping concentration due to the introduction of widely distributed Mo 4d states below the conduction band minimum. The increase in the width of the conduction band with increasing doping concentration shows enhancement in the conductivity which may be helpful in increasing electron–hole pairs separation and consequently decreases the carrier recombination. The Mo doped anatase TiO₂ exhibits the n-type characteristic due to the shifting of Fermi level from the top of the valence band to the bottom of the conduction band. Furthermore, a shift in the absorption edge towards visible light region is apparent from the absorption spectrum which will enhance its photocatalytic activity. All the doped models have depicted visible light absorption and the absorption peaks shift towards higher energies in the visible region with increasing doping concentration. Our results describe the way to tailor the band gap of anatase TiO₂ by changing Mo doping concentration. The Mo doped anatase TiO₂ will be a very useful photocatalyst with enhanced visible light photocatalytic activity.     

IR and XPS investigation of visible-light photocatalysis—Nitrogen-carbon-doped TiO2 film

To use solar irradiation or interior lighting efficiently, we sought a photocatalyst with high reactivity under visible light. Nitrogen and carbon doping TiO_2−x−yN_xC_y films were obtained by heating the TiO₂ gel in an ionized N₂ gas and then were calcined at 500 °C. The TiO_2−x−yN_xC_y films have revealed an improvement over the TiO₂ films under visible light (wavelength, 500 nm) in optical absorption and photocatalytic activity such as photodegradation of methyl orange. X-ray photoemission spectroscopy, infrared spectrum and UV-visible (UV-vis) spectroscopy were used to find the difference of two kinds of films. Nitrogen and carbon doped into substitutional sites of TiO₂ has been proven to be indispensable for band-gap narrowing and photocatalytic activity.     

Photocatalytic photodegradation of xanthate over C, N, S-tridoped TiO2 nanotubes under visible light irradiation

C, N, S-tridoped TiO₂ nanotubes were synthesized via hydrothermal synthesis and post-treatment, and characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), X-ray photoelectron spectra (XPS), the Brunauer-Emmett-Teller method (BET), and UV-vis diffuse reflectance spectroscopy (DRS). The UV-diffuse reflectance spectra of all the C, N, S-tridoped TiO₂ nanotubes greatly extended the absorption edge to the visible light region, and the absorbance in the visible region increased with increasing molar ratio of thiourea to Ti (R), which could be attributed to C, N, S-tridoping in the form of cation C-doping, interstitial N-doping, cation S-doping, and adsorbed ions’ states. The photocatalytic activity of C, N, S-tridoped TiO₂ nanotubes was evaluated by photocatalytic photodegradation of potassium ethyl xanthate (KEX) under visible light irradiation. It was found that the photocatalytic activity of the prepared samples increased with increasing molar ratio of thiourea to Ti (R). At R=6, the photocatalytic activity of the tridoped sample TNTS-6 reached a maximum value. With further increase in R, photocatalytic activity of the sample decreased, which could be attributed to the high visible light activity resulting from the balance between visible light absorption and recombination of electron/hole pairs.     

Effects of native defects on the electronic structure and photocatalytic activity in anatase TiO2 by first principles calculations

The crystal structure, electronic structure, optical properties and photocatalytic activity of the native defects in anatase TiO₂ were investigated based on the density-functional theory (DFT). The results show that oxygen vacancies (V_O) have the lowest formation energy, and thus are easiest to form in the bulk structure. The conduction and valence band moves to the high or low energy region, and the energy gap becomes narrower for the native point defect models. In particular, oxygen interstitials (O_i) have a direct band gap, and new gap states appear in the band gap, which can be responsible for the high photocatalytic efficiency in anatase TiO₂. The phenomenon of “impurity compensation” takes place for the oxygen and titanium interstitials. Ti vacancy (V_Ti) can promote the utilization of solar light by analyzing the absorption spectra. All the calculated results show that O_i and V_Ti are beneficial in improving the photocatalytic activity of TiO₂ in the UV–visible light range.     

P掺杂锐钛矿相TiO2的第一性原理计算

利用基于密度泛函理论的第一性原理对不同P掺杂形式(P替位Ti, P替位O, 间隙P)的锐钛矿相TiO₂的晶格常数、电荷布居、能带结构、分态密度和吸收光谱进行了计算. 结果表明, P替位Ti时, TiO₂体积减小, P替位O和间隙P的存在使TiO₂的体积膨胀; 替位Ti的P和间隙P均有不同程度的氧化, 而替位O的P带有负电荷. 三种P掺杂形式均导致锐钛矿相TiO₂禁带宽度的增大, 并在TiO₂禁带之内引入了掺杂局域能级. P掺杂导致TiO₂禁带宽度增大的程度依次为: 间隙P>P替位Ti>P替位O. 吸收光谱的计算结果表明, P替位Ti并不能增强TiO₂的可见光吸收能力, 但间隙P的存在大幅提高了TiO₂的可见光光吸收能力, 间隙P有可能是造成实验上P掺杂增强锐钛矿相TiO₂光催化活性的重要原因. 关键词： P掺杂 2')" href="#">锐钛矿相TiO₂ 第一性原理     

Efficient visible-light-induced photocatalytic degradation of MO on the Cr-nanocrystalline titania-S

In order to improve visible light photocatalytic activities of the nanometer TiO₂, a novel and efficient Cr,S-codoped TiO₂ (Cr-TiO₂-S) photocatalyst was prepared by precipitation-doping method. The crystalline structure, morphology, particle size, and chemical structure of Cr-TiO₂-S were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), scanning electron microscopy (SEM), and Fourier transform infrared (FT-IR) techniques, respectively. Results indicate that the doping of Cr and S, cause absorption edge shifts to the visible light region (λ > 420 nm) compare to the pure TiO₂, reduces average size of the TiO₂ crystallites, enhances desired lattice distortion of Ti, promotes separation of photo-induced electron and hole pair, and thus improves pollutant decomposition under visible light irradiation. The photocatalytic activities of Cr-TiO₂-S nanoparticles were evaluated using the photodegradation of methyl orange (MO) as probe reaction under the irradiation of UV and visible light and it was observed that the Cr-TiO₂-S photocatalyst shows higher visible photocatalytic activity than the pure TiO₂. The optimal Cr-TiO₂-S concentration to obtain the highest photocatalytic activity was 5 mol% for both of Cr and S.     

Preparation and photocatalytic activity of nitrogen-doped TiO2 hollow nanospheres

TiO₂ hollow nanospheres were prepared using silicon oxide as a template. N-doped titanium oxide hollow spheres, TiO_2−xN_x were synthesized by reacting TiO₂ hollow spheres with thiourea at 500 °C. XRD and XPS data showed that oxygen was successfully substituted by nitrogen through the nitrogen-doping reaction, and finally N-doped TiO₂ hollow spheres were formed. The N-doped TiO₂ hollow spheres showed new absorption shoulder in visible light region so that they were expected to exhibit photocatalytic activity in the visible light. The photocatalytic activity of N-doped TiO₂ hollow spheres under visible light was similar to that of normal spherical TiO_2−xN_x in spite of the structural difference.     

Two-step nitridation of photocatalytic TiO2 films by low energy ion irradiation

Nitridation of TiO₂ films is performed by the simultaneous irradiation of low-energy N₂⁺ and H₂⁺ ions under substrate-heating condition. Spectroscopic observations of the resultant films clarify the formation of nitrogen-substituted TiO₂ (TiO_2−xN_x) with large N fractions and the agglomeration of undesirable oxynitride species attributed to the deep states in the band gap. We find that the addition of a thin TiO₂ cap layer on the ion-irradiated films improves the nitrogen bonding structure and distribution near the surfaces, leading to a good photocatalytic performance even in the visible region.     

硼(氮、氟)掺杂对TiO2纳米颗粒光学性能的影响

利用X射线衍射谱、拉曼光谱和紫外-可见光吸收光谱研究了硼(氮、氟)掺杂对TiO₂纳米颗粒光学性能的影响.X射线衍射谱和拉曼光谱结果表明,掺硼(氮、氟)对TiO₂纳米颗粒的锐钛矿相晶体结构无明显影响,而其锐钛矿晶格出现畸变(c/a值增大),这被归因于掺杂原子对TiO₂纳米颗粒表面氧原子缺位沿晶格c轴方向的占据.另外,掺硼(氮、氟)TiO₂纳米颗粒吸收带红移与TiO相似文献   

S掺杂对锐钛矿相TiO2电子结构与光催化性能的影响

采用基于第一性原理的平面波超软赝势方法研究了掺杂不同价态S的锐钛矿相TiO₂的晶体结构、杂质形成能、电子结构及光学性质.计算结果表明硫在掺杂体系中的存在形态与实验中的制备条件有关;掺杂后晶格发生畸变、原子间的键长及原子的电荷量也发生了变化,导致晶体中的八面体偶极矩增大; S 3p态与O 2p态、Ti 3d态杂化而使导带位置下移、价带位置上移及价带宽化,从而导致TiO₂的禁带宽度变窄、光吸收曲线红移到可见光区.这些结果很好地解释了S掺杂锐钛矿相TiO₂在可见光下具有优良的光催化性能的内在原因.根据计算结果分析比较了硫以不同离子价态掺杂对锐钛矿相TiO₂电子结构和光催化性能影响的差别. 关键词： 2')" href="#">锐钛矿相TiO₂ S掺杂 第一性原理 光催化性能     

Aerosol-assisted flow synthesis of WxTi1−xO2 solid solution spheres with enhanced photocatalytic activity

In this paper, W_xTi_1−xO₂ solid solutions (x = 0.000, 0.005, 0.010, 0.015, and 0.020) microspheres were synthesized with an aerosol-assisted flow synthesis method. The resulting samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), nitrogen sorption, UV-vis diffuse reflectance spectrum (DRS) and X-ray photoelectron spectroscopy (XPS). The photocatalytic activities of the as-prepared catalysts were measured by the degradation of rhodamine B (RhB) under visible light irradiation (λ ≥ 420 nm). All the solid solutions exhibited higher photocatalytic activities than pure TiO₂ and the W_0.015Ti_0.985O₂ solid solution possessed the highest photocatalytic activity. The degradation constant of RhB on W_0.015Ti_0.985O₂ solid solution catalyst was about 15 times of that of the pure TiO₂ and 25 times of that of Degussa P25, respectively. This study provides an effective method to prepare visible light photocatalysts on a large scale.     

The preparation of nitrogen-doped TiO2−xNx photocatalyst coated on hollow glass microbeads

In this paper, the effective method for nitrogen-doped TiO_2−xN_x photocatalyst coated on hollow glass microbeads is described, which uses titanium tetraisopropoxide [Ti(iso-OC₃H₇)₄] as the raw materials and gaseous ammonia as a heat treatment atmosphere. The effects of heat treatment temperature and time on the photocatalytic activity of TiO_2−xN_x/beads are studied. The photocatalyst is characterized by the UV-vis diffuse reflection spectroscopy, X-ray photoelectron spectroscopy (XPS), X-ray powder diffraction (XRD), Brunauer-Emmett-Teller (BET) analysis and scanning electron microscopy (SEM). The results show that when the TiO_2−xN_x/beads is heated at 650 °C for 5 h, the photocatalytic activity of the TiO_2−xN_x/beads is the best. Compared with TiO₂, the photoabsorption wavelength range of nitrogen-doped TiO_2−xN_x red shifts of about 60 nm, and the photoabsorption intensity increases as well. The photocatalytic activity of the TiO_2−xN_x/beads is higher than that of the TiO₂/beads under visible light irradiation. The presence of nitrogen neither influences on the transformation of anatase to rutile, nor creates new crystal phases. When the TiO_2−xN_x/beads is heated at 650 °C for 5 h, the amount of nitrogen-doped is 0.53 wt.% in the TiO_2−xN_x. As the density of TiO_2−xN_x/beads prepared is lower than 1.0 g/cm³, it may float on water surface and use broader sunlight spectrum directly.     

Sol-gel derived S,I-codoped mesoporous TiO2 photocatalyst with high visible-light photocatalytic activity

A mesoporous S,I-codoped TiO₂ photocatalyst with high visible light photocatalytic activity was synthesized through the hydrolysis and condensation of titanium isopropoxide with thiourea and iodic acid as the precursors. The as-prepared catalysts were characterized by X-ray diffraction (XRD), scanning electron microscope (SEM), UV-vis diffuse reflectance (DRS), X-ray photoelectron spectroscopy (XPS), Fourier translation infrared spectroscopy (FT-IR), and N₂ adsorption. The results showed that the cations of S⁶⁺ and I⁵⁺ could substitute for some of the lattice titanium (Ti⁴⁺). The S,I-codoping forms the new bands above the valence band and narrows the band-gap of the TiO₂, then shifts the absorption edge from UV light region to visible light range. The activity of the catalyst was examined by photodegradation of methylene blue in an aqueous solution under visible light irradiation. The activity of the S,I-codoped catalyst is far superior to that of single S or I-doped TiO₂ counterpart. The high visible light photocatalytic activity could be attributed to the strong absorption of light, well-crystalline anatase phase, and mesoporous microstructure.     

Visible light sensitization effect of polyaminobenzoate adsorbed on TiO2 nanocrystal surface

Poly-o-aminobenzoate (POA) was prepared by oxidizing o-aminobenzoic acid with (NH₄)₂S₂O₈ in an acidic solution. POA was adsorbed on TiO₂ nanocrystal surface to obtain a POA-TiO₂ nanocomposite. The polymerization reaction, structure, adsorption reaction on TiO₂ surface, and visible light sensitization effect of the polymer adsorbed on TiO₂ surface were studied by FT-IR and UV-visible spectra, cyclic voltammetry, and measurements of visible light photoelectrochemical and photocatalytic activities. Three kinds of POA with different long conjugate structures can be formed. These polymers have large absorbance in wide visible light region. POA molecules can be adsorbed on TiO₂ surface by anchoring their carboxylate groups to the TiO₂ surface with a multi-bridging chelating mode, which causes formation of the POA-TiO₂ nanocomposite with a high stability. POA adsorbed on the TiO₂ nanocrystal showed high visible light sensitization effect in the photocatalytic reaction.     

N,Fe, La三掺杂锐钛矿型TiO2能带调节的理论与实验研究

采用基于密度泛函理论(DFT)的平面波超软赝势方法(PWPP), 利用Material studio 计算N, Fe, La三种元素掺杂引起的锐钛矿TiO₂晶体结构、能带结构和态密度变化. 并通过溶胶-凝胶法制得锐钛矿型本征TiO₂, N, Fe共掺杂TiO₂和N, Fe, La共掺杂TiO₂; 用X射线衍射和扫描电镜表征结构; 紫外-可见分光光度计检测TiO₂对甲基橙的降解效率变化. 计算结果表明, 由于N, Fe, La三掺杂TiO₂的晶格体积、键长等发生变化, 导致晶体对称性下降, 光生电子-空穴对有效分离, 同时在导带底和价带顶形成杂质能级, TiO₂禁带宽度由1.78 eV变为1.35 eV, 减小25%, 光吸收带边红移, 态密度数增加, 电子跃迁概率提升, 光催化能力增加. 实验结果表明: 离子掺杂使颗粒变小, 粒径大小: 本征TiO₂>N/Fe_TiO₂>N/Fe/La_TiO₂, 并测得N/Fe/La_TiO₂发光峰425 nm, 能隙减小, 光催化能力比N/Fe_TiO₂强, 增强原因是杂质能级和电子态数量增加引起.