Efficient visible-light-induced photocatalytic degradation of MO on the Cr-nanocrystalline titania-S

In order to improve visible light photocatalytic activities of the nanometer TiO₂, a novel and efficient Cr,S-codoped TiO₂ (Cr-TiO₂-S) photocatalyst was prepared by precipitation-doping method. The crystalline structure, morphology, particle size, and chemical structure of Cr-TiO₂-S were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), scanning electron microscopy (SEM), and Fourier transform infrared (FT-IR) techniques, respectively. Results indicate that the doping of Cr and S, cause absorption edge shifts to the visible light region (λ > 420 nm) compare to the pure TiO₂, reduces average size of the TiO₂ crystallites, enhances desired lattice distortion of Ti, promotes separation of photo-induced electron and hole pair, and thus improves pollutant decomposition under visible light irradiation. The photocatalytic activities of Cr-TiO₂-S nanoparticles were evaluated using the photodegradation of methyl orange (MO) as probe reaction under the irradiation of UV and visible light and it was observed that the Cr-TiO₂-S photocatalyst shows higher visible photocatalytic activity than the pure TiO₂. The optimal Cr-TiO₂-S concentration to obtain the highest photocatalytic activity was 5 mol% for both of Cr and S.     

Sol-gel derived S,I-codoped mesoporous TiO2 photocatalyst with high visible-light photocatalytic activity

A mesoporous S,I-codoped TiO₂ photocatalyst with high visible light photocatalytic activity was synthesized through the hydrolysis and condensation of titanium isopropoxide with thiourea and iodic acid as the precursors. The as-prepared catalysts were characterized by X-ray diffraction (XRD), scanning electron microscope (SEM), UV-vis diffuse reflectance (DRS), X-ray photoelectron spectroscopy (XPS), Fourier translation infrared spectroscopy (FT-IR), and N₂ adsorption. The results showed that the cations of S⁶⁺ and I⁵⁺ could substitute for some of the lattice titanium (Ti⁴⁺). The S,I-codoping forms the new bands above the valence band and narrows the band-gap of the TiO₂, then shifts the absorption edge from UV light region to visible light range. The activity of the catalyst was examined by photodegradation of methylene blue in an aqueous solution under visible light irradiation. The activity of the S,I-codoped catalyst is far superior to that of single S or I-doped TiO₂ counterpart. The high visible light photocatalytic activity could be attributed to the strong absorption of light, well-crystalline anatase phase, and mesoporous microstructure.     

镧掺杂介孔TiO2光催化剂的制备、表征及其光催化性能

以钛酸四正丁酯和硝酸镧为原料, 以P123为模板剂,采用模板法合成了La掺杂型介孔TiO₂光催化剂, 借助TGA-DSC、BET、XRD及UV-Vis等测试手段对样品进行了表征,并以苯酚为模型污染物考察了镧掺杂量对样品光催化活性的影响．结果表明: La掺杂介孔TiO₂光催化剂孔径分布较均匀(～10 nm),比表面积可达165 m²/g．与纯介孔TiO₂相比,经掺杂改性后的样品在紫外光区及可见光区的吸收显著增强,对光具有更高的利用率,La掺杂可显著提高介孔TiO₂的光催化活性.     

Sputter deposition of high transparent TiO2−xNx/TiO2/ZnO layers on glass for development of photocatalytic self-cleaning application

In this study, TiO_2−xN_x/TiO₂ double layers thin film was deposited on ZnO (80 nm thickness)/soda-lime glass substrate by a dc reactive magnetron sputtering. The TiO₂ film was deposited under different total gas pressures of 1 Pa, 2 Pa, and 4 Pa with constant oxygen flow rate of 0.8 sccm. Then, the deposition was continued with various nitrogen flow rates of 0.4, 0.8, and 1.2 sccm in constant total gas pressure of 4 Pa. Post annealing was performed on as-deposited films at various annealing temperatures of 400, 500, and 600 °C in air atmosphere to achieve films crystallinity. The structure and morphology of deposited films were evaluated by X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), and atomic force microscopy (AFM). The chemical composition of top layer doped by nitrogen was evaluated by X-ray photoelectron spectroscopy (XPS). Photocatalytic activity of samples was measured by degradation of Methylene Blue (MB) dye. The optical transmittance of the multilayer film was also measured using ultraviolet-visible light (UV-vis) spectrophotometer. The results showed that by nitrogen doping of a fraction (∼1/5) of TiO₂ film thickness, the optical transmittance of TiO_2−xN_x/TiO₂ film was compared with TiO₂ thin film. Deposited films showed also good photocatalytic and hydrophilicity activity at visible light.     

Visible-light-activated Ce-Si co-doped TiO2 photocatalyst

To enhance the visible photocatalytic activity and thermal stability of TiO₂, Ce-Si co-doped TiO₂ materials were synthesized through a nonaqueous method of which the purpose was to reduce the aggregation between TiO₂ particles. The obtained materials maintained anatase phase and large surface area of 103.3 m² g⁻¹ even after calcined at 800 °C. The XPS results also indicated that Si was weaved into the lattice of TiO₂, and Ce mainly existed as oxides on the surface of TiO₂ particles. The doped Si might enhance surface area and suppress transformation from anatase to rutile, while the doped Ce might cause visible absorption and inhibit crystallite growth during heat treatment. Evaluated by decomposing dye Rhodamine B, visible photocatalytic activity of Ce-Si co-doped TiO₂ was obviously higher than that of pure TiO₂ and reached the maximum at Ce and Si contents of 0.5 mol% and 10 mol%.     

Preparation and characterization of iodine-doped mesoporous TiO2 by hydrothermal method

Iodine-doped mesoporous TiO₂ (I/TiO₂) was prepared by hydrothermal method, using tetrabutyl titanate as precursor, potassium iodate as iodine sources. The as-prepared I/TiO₂ catalysts were characterized by UV-vis, XRD, TEM, BET, TG/DTA, XPS and photoluminescence (PL) spectroscopy. Production of OH radicals on the I/TiO₂ surface was detected by the PL technique using terephthalic acid as a probe molecule. The effects of hydrothermal reaction temperature, calcination temperature and iodine doping content on the structure and properties of the catalysts were investigated. The results showed that iodine-doped TiO₂ calcinated at 300 °C have good anatase crystal. The optimal hydrothermal conditions have been determined to be that reaction temperature 120 °C, calcinated temperature 300 °C and added 1.16 mmol iodine dopants. The average particle size of I/TiO₂ synthesized under optimal condition (I-3 sample) is about 3.9 nm. The I-3 photocatalyst contains 100% anatase crystalline phase of TiO₂. BET specific surface area of I-3 sample is184.8 m² g⁻¹ and is 3.67 times that of pure TiO₂ (50.37 m² g⁻¹). Iodine in I/TiO₂ catalyst mainly exists in the form of I₂, and photoactivity of I/TiO₂ catalyst in visible light comes from photosensitize of I₂. I/TiO₂ catalysis shows very high efficiency for the degradation of phenol under visible light.     

Preparation and visible light photocatalytic activity of mesoporous N, S-codoped TiO2(B) nanobelts

The mesoporous N, S-codoped TiO₂(B) nanobelts are synthesized via hydrothermal synthesis and post-treatment, and characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), N₂ adsorption-desorption measurements (BET), X-ray photoelectron spectra (XPS), and UV-vis diffuse reflectance spectra (DRS). The results show that the prepared samples are mesoporous structured and exhibit stronger absorption in the visible light region with red shift in the absorption edge. The photocatalytic activity of N, S-codoped mesoporous TiO₂(B) nanobelts is evaluated by the photocatalytic photodegradation of potassium ethyl xanthate (KEX) under visible light irradiation. It is found that the photocatalytic activity of the prepared samples increases with increasing the molar ratio of thiourea to Ti (R). At R = 3, the photocatalytic activity of the N, S-codoped TiO₂(B) sample TBLTS-3 reaches a maximum value. With further increasing R, the photocatalytic activity of the sample decreases. The high photocatalytic activity of N, S-codoped TiO₂(B) nanobelts can be attributed to the balance between strong absorption in visible light region and low recombination rate of electron/hole pairs.     

Effect of Cr incorporation on the structural and optoelectronic properties of TiO2:Cr deposited by means of a magnetron co-sputtering process

In this work, we report on the effect of Cr incorporation on the microstructural and optical properties of TiO₂:Cr thin films deposited by the RF-magnetron sputtering method. The structural, morphological, chemical bonding and optoelectronic properties of the sputter-deposited TiO₂:Cr films were systematically investigated, as a function the incorporated Cr content, by means of various techniques including X-ray diffraction (XRD), atomic force microscopy (AFM), Fourier-Transform Infra-Red (FTIR) absorption, X-ray Photoelectron Spectroscopy (XPS) and ellipsometry. The Cr incorporation into the TiO₂ films was controlled by adjusting the RF power (P_Cr) on the Cr target during the co-sputtering process of TiO₂ and Cr. We were thus able to demonstrate that by varying P_Cr from 8 W to 150 W, the Cr content of the TiO₂:Cr films can be fairly controlled from ∼2 at.% to ∼18 at.% and their associated bandgap engineered from 3.3 eV to 1.5 eV. The room-temperature deposited TiO₂:Cr are mainly amorphous with the presence of some TiO₂ nanocrystallites, and their density increases as their Cr content is increased. The Cr inclusions were found to coexist under both metallic and oxidized forms in the films. By subjecting the TiO₂:Cr films to post-annealing treatment (at 550 °C), their crystalline structure was found to be sensitive to their Cr content. Indeed, an anatase-to-rutile phase transformation has been pointed out to occur at a Cr content of ∼7 at.%. Likewise, the Cr-content dependence of the bandgap of annealed TiO₂:Cr films undergoes a transition around the 7 at.% of Cr. Our results demonstrate the ability to control the Cr-content of TiO₂:Cr films, which leads to tune their optoelectronic properties, such as bandgap or optical absorption edge.     

Preparation and characterization of TiO2 photocatalysts co-doped with iron (III) and lanthanum for the degradation of organic pollutants

Titanium dioxide photocatalysts co-doped with iron (III) and lanthanum were prepared by a facile sol-gel method. The structure of catalysts was characterized by X-ray diffraction (XRD), Raman spectroscopy, UV-vis diffuse reflectance spectroscopy and X-ray photoelectron spectroscopy (XPS). The photocatalytic activities of the samples were evaluated by the degradation of methylene blue in aqueous solutions under visible light (λ > 420 nm) and UV light irradiation. Doping with Fe³⁺ results in a lower anatase to rutile (A-R) phase transformation temperature for TiO₂ particles, while doping with La³⁺ inhibits the A-R phase transformation, and co-doping samples indicate that Fe³⁺ partly counteracts the effect of La³⁺ on the A-R transformation property of TiO₂. Fe-TiO₂ has a long tail extending up the absorption edges to 600 nm, whereas La-TiO₂ results in a red shift of the absorption. However, Fe and La have synergistic effect in the absorption of TiO₂. Compared with Fe³⁺ and La³⁺ singly doped TiO₂, the co-doped simple exhibits excellent visible light and UV light activity and the synergistic effect of Fe³⁺ and La³⁺ is responsible for improving the photocatalytic activity.     

Effect of N2 ion flux on the photocatalysis of nitrogen-doped titanium oxide films by electron-beam evaporation

Nitrogen-doped titanium oxide (TiO_xN_y) films were prepared with ion-assisted electron-beam evaporation. The nitrogen (N) incorporated in the film is influenced by the N₂ flux modulated by the N₂ flow rate through an ion gun. The TiO_xN_y films have the absorption edge of TiO₂ red-shifted to 500 nm and exhibit visible light-induced photocatalytic properties in the surface hydrophilicity and the degradation of methylene blue. The structures and states of nitrogen in the films are investigated by X-ray diffraction patterns (XRD), and X-ray photoelectron spectroscopy (XPS) and related to their visible light-induced photocatalytic properties. The results indicate that the substitutional N in anatase TiO₂ can induce visible light photocatalysis. The substitutional N is readily doped by the energetic nitrogen ions from the ion gun. The best photocatalytic activity is obtained at the largest N loading about 5.6 at.%, corresponding to the most substitutional N in anatase TiO₂. The film exhibits the degradation of methylene blue with a rate-constant (k) about 0.065 h⁻¹ and retaining 7° water contact angle on the surface under visible light illumination.     

A combined experimental and theoretical analysis of Fe-implanted TiO2 modified by metal plasma ion implantation

Photocatalyst titanium dioxide (TiO₂) thin films were prepared using sol-gel process. To improve the photosensitivity of TiO₂ at visible light, transition metal of Fe was implanted into TiO₂ matrix at 20 keV using the metal plasma ion implantation process. The primary phase of the Fe-implanted TiO₂ films is anatase, but X-ray diffraction revealed a slight shift of diffraction peaks toward higher angles due to the substitutional doping of iron. The additional band gap energy levels were created due to the formation of the impurity levels (Fe-O) verified by X-ray photoelectron spectroscopy, which resulted in a shift of the absorption edge toward a longer wavelength in the absorption spectra. The optical band gap energy of TiO₂ films was reduced from 3.22 to 2.87 eV with an increase of Fe ion dosages from 0 to 1 × 10¹⁶ ions/cm². The band gap was determined by the Tauc plots. The photocatalysis efficiency of Fe-implanted TiO₂ was assessed using the degradation of methylene blue under ultraviolet and visible light irradiation. The calculated density of states for substitutional Fe-implanted TiO₂ was investigated using the first-principle calculations based on the density functional theory. A combined experimental and theoretical Fe-implanted TiO₂ film was formed, consistent with the experimentally observed photocatalysis efficiency of Fe-implanted TiO₂ in the visible region.     

Synthesis, characterization and application of iodine modified titanium dioxide in phototcatalytical reactions under visible light irradiation

Iodine doped titanium dioxide has been successfully prepared by simple hydrolysis of tetrabutyl titanate in the presence of iodic acid. The adopted method allowed for the production of spherical iodine doped titaniun dioxide nanoparticles with varied amount of iodine content. Analysis by X-ray diffraction, Raman, transmission electron microscopy as well as UV-vis DRS revealed that titanium dioxide nanostructures were doped with iodine which existed in two different valence states I⁵⁺ and I⁻. The iodine in the form of I⁵⁺ is believed to have doped into the lattice whereas I⁻ was well dispersed on the surface of TiO₂ probably as iodine adducts hence rendering it to be highly absorbing in visible light region. The I-TiO₂ exhibited improved photocatalytic activity toward degradation of acid orange 7 (AO7), methyl orange (MO) and 2,4-dichlorophenol (2,4-DCP) under visible light over the pristine TiO₂ prepared by the same method. High catalytic properties are attributed to iodine doping which led to high specific surface area, absorption in visible region as well as alleviation of charge carrier recombination. The most probable route undertaken in the degradation of AO7 is through indirect oxidation by the hydroxyl radicals.     

Influence of physicochemical-electronic properties of transition metal ion doped polycrystalline titania on the photocatalytic degradation of Indigo Carmine and 4-nitrophenol under UV/solar light

To understand the role of dopant inside TiO₂ matrix, anatase TiO₂ was doped with transition metal ions like Mn²⁺, Fe³⁺, Ru³⁺ and Os³⁺ having unique half filled electronic configuration and their photocatalytic activity was probed in the degradation of Indigo Carmine (IC) and 4-nitrophenol (NP) under UV/solar light. For comparison, TiO₂ was also doped with V⁵⁺, Ni²⁺ and Zn²⁺ metal ions having d⁰, d⁸ and d¹⁰ electronic configuration respectively. Irrespective of excitation source UV/solar light and nature of the organic pollutant, photocatalytic activities of doped photocatalysts followed the order: Mn²⁺-TiO₂ > Fe³⁺-TiO₂ > Ru³⁺-TiO₂ ≥ Os³⁺-TiO₂ > Zn²⁺-TiO₂ > V⁵⁺-TiO₂ > Ni²⁺-TiO₂ at an optimum concentration of dopant. Based on the experimental results obtained, it is proposed that the existence of dopant with half filled electronic configuration in TiO₂ matrix which is known to enhance the photocatalytic activity is not universal! Rather it is a complex function of several physicochemical-electronic properties of doped titania. Enhanced photocatalytic activity of Mn²⁺ (0.06 at.%)-TiO₂ was attributed to the combined factors of high positive reduction potential of Mn²⁺/Mn³⁺ pairs, synergistic effects in the mixed polymorphs of anatase and rutile, smaller crystallite size with high intimate contact between two phases and favorable surface structure of the photocatalyst. Despite the intense research devoted to transition metal ion doped TiO₂, it is rather difficult to make unifying conclusion which is highlighted in this study.     

Synthesis and characterization of the Pd/InVO4-TiO2 co-doped thin films with visible light photocatalytic activities

Novel Pd/InVO₄-TiO₂ thin films with visible light photocatalytic activity were synthesized from the Pd and InVO₂ co-doped TiO₂ sol via sol-gel method. The photocatalytic activities of Pd/InVO₄-TiO₂ thin films were investigated based on the oxidative decomposition of methyl orange in aqueous solution. The as-prepared samples were characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), X-ray photoelectron spectroscopy (XPS) and UV-vis absorption spectroscopy (UV-vis). The results indicate that the Pd/InVO₄-TiO₂ thin films are compact, uniform and consist of sphere nanoparticles with diameters about 80-100 nm. The UV-vis spectra show that the Pd/InVO₄-TiO₂ thin films extend the light absorption spectrum toward the visible region. XPS results reveal that doped Pd exist in the form of metallic palladium. The photocatalytic experiments demonstrate that Pd doping can effectively enhance the photocatalytic activities of InVO₄-TiO₂ thin films in decomposition of aqueous methyl orange under visible light irradiation. It has been confirmed that Pd/InVO₄-TiO₂ thin films could be excited by visible light (E < 3.2 eV) due to the existence of the Pd and InVO₄ doped in the films.     

Design and fabrication of a TiO2/nano-silicon composite visible light photocatalyst

Nano-silicon (nc-Si) was utilized as the charges generator to promote the photocatalytic and super-hydrophilic reactivity of TiO₂ film under visible light irradiation. The photocatalytic ability of TiO₂/nc-Si composite photocatalyst was evaluated by a set of experiments to photodecompose 100 ppm methylene blue (MB) in aqueous solution. And the super-hydrophilic property was characterized by measuring the water droplet contacts angle, under visible light irradiation in atmospheric air and at room temperature. Under 100 mW/cm² visible light irradiation, the droplet contact angles were reduced to 0° within 4 h with nc-Si charge generator. Additionally, the rate constant of MB photo-degradation was promoted 6.6 times.     

Optical spectroscopy of heavily Ho-doped BaY2F8 crystals

The ultraviolet, visible, and near IR (0.8-2.4 μm) luminescence spectra of BaY₂F₈ single crystals heavily doped with Ho³⁺ ions (10 and 30 mol%) have been investigated at room temperature and 12 K, together with the luminescence decay curves (up to 300 μs) of the visible emission. Excitation in the visible region gives rise to very strong emission bands originating from the first ⁵I₇ level and located around 2070 nm. However the ⁵I₇ emission is not observed upon excitation at wavelengths shorter than 300 nm. The inter-ionic processes are found to shorten the decay times of the levels emitting in the visible region with respect to the corresponding radiative lifetimes.     

Preparation and characterization of visible light responsive Fe2O3-TiO2 composites

In this study we present the effects of iron oxide (Fe₂O₃) on titanium dioxide (TiO₂) in synthesising visible-light reactive photocatalysts. A Fe₂O₃-TiO₂ composite photocatalyst was synthesized from Fe₂(SO₄)₃ and Ti(SO₄)₂ by a ethanol-assisted hydrothermal method. The preparation conditions were optimized through the investigation of the effects of hydrothermal temperature and time as well as molar ratio of Ti to Fe on the photocatalytic activity. The visual, physical and chemical properties of the Fe₂O₃-TiO₂ composites were investigated. The results showed that α-Fe₂O₃ and anatase TiO₂ were present in the composites. The Fe₂O₃-TiO₂ synthesized under optimum condition consisted of mesoporous structure with an average pore size of 4 nm and a surface area of 43 m²/g. Under visible and solar light irradiation, the photocatalytic activity of optimized sample was significantly higher than that of pure TiO₂. This sample led to a photodegradation efficiency of 90% and 40% of auramine under visible light and solar light, respectively.     

Effect of cobalt doping and annealing on properties of titania thin films prepared by sol-gel process

Undoped and cobalt doped titania (TiO₂) thin films have been prepared on Si(1 0 0) monocrystal and quartz substrate using the sol-gel deposition method and annealed in air at 450, 550, 650, 750, 850, 950 and 1050 °C. Several experimental techniques (AFM, XRD, Raman spectroscopy, XRR, EDX, XPS, XAS, UV-VIS spectroscopy) have been used to characterize these films. Further more the degree of light induced hydrophilicity was estimated by measuring the contact angle of a water droplet on the film. Increase of the annealing temperature and in smaller degree also cobalt doping predispose titania crystallite growth. The rutile phase was detected at lower temperatures in the cobalt doped films than in the undoped titania films. Cobalt in the cobalt doped TiO₂ was seen to be in Co²⁺ oxidation state, mainly in CoTiO₃ phase when films were annealed at temperatures higher than 650 °C. Cobalt compounds segregated into the sub-surface region and to the surface of the titania, where they formed islands. Cobalt doping red-shifted the fundamental absorption edge further into the visible range, however it did not enhance the light induced hydrophilicity of the thin film surface as compared to the undoped titania thin films.     

An origin of light induced centers in the visible range in ferroelectric oxides: possible role of the states of charge transfer vibronic excitons

A light induced absorption peculiarity connected with an absorption peak in the visible range for SBN/Ce was detected. The analysis of these data together with investigation results for a visible range center (VIS-center) absorption study in SBN/Ce and Cr, in nominally pure strontium barium niobate (SBN) as well as in Ba_0.77Ca_0.23TiO₃ crystals give support to charge transfer vibronic excitons (CTVEs) as origin of the phenomenon. While the fast (with relaxation time ∼1 ns at T∼300 K) response can be connected with transitions between excited branches of the adiabatic potential of the CTVE phase, the slow (with relaxation time ∼50 s at T∼230 K for SBN/Cr) response is connected with transitions between ground and first excited CTVE phase branches. The additional contribution to the latter effect due to the absorption of recharged oxygen ions which are in the framework of charge transfer induced by the CTVE cannot be disregarded. The explanation of the main results of the experiments shows that the VIS-center phenomena can be induced by the CTVE-states.     

IR and XPS investigation of visible-light photocatalysis—Nitrogen-carbon-doped TiO2 film

To use solar irradiation or interior lighting efficiently, we sought a photocatalyst with high reactivity under visible light. Nitrogen and carbon doping TiO_2−x−yN_xC_y films were obtained by heating the TiO₂ gel in an ionized N₂ gas and then were calcined at 500 °C. The TiO_2−x−yN_xC_y films have revealed an improvement over the TiO₂ films under visible light (wavelength, 500 nm) in optical absorption and photocatalytic activity such as photodegradation of methyl orange. X-ray photoemission spectroscopy, infrared spectrum and UV-visible (UV-vis) spectroscopy were used to find the difference of two kinds of films. Nitrogen and carbon doped into substitutional sites of TiO₂ has been proven to be indispensable for band-gap narrowing and photocatalytic activity.